LDA抽运Nd∶YAG/KTP腔内和频589nm连续波激光器

报道了一种激光二极管阵列(LDA)抽运Nd∶YAG双波长和频黄光激光器.黄激光是由Nd∶YAG晶体的1064 nm和1319 nm谱线腔内和频产生.以KTP为和频晶体,采用Ⅱ类临界相位匹配,在12 W的808 nm抽运功率下,获得了最高功率为430 mW连续波基横模的589 nm黄激光输出,光光转换效率为3.6%,光束质量因子M2<1.2.实验结果表明采用激光二极管阵列抽运Nd∶YAG/KTP腔内和频技术是获得黄激光的高效方法,并可以应用到其它激光增益介质的两条谱线进行腔内和频,获得更多不同颜色的单谱线激光输出.     

激光感生碰撞能量转移实验

首次观察到Eu(6s6p)^P9/2至Sr(5s10s)^1So、准稳态翼为紫翼的激光感生碰撞能量转移实验现象,其荧光波长为458.42nm,峰值转移激光波长为459.75nm,并对其激发函数谱随温度和随转移激光能量改变进行实验研究,测量了激光感生碰撞能量转移谱的截面,证实了激光感生碰撞能量转移谱为非对称谱。     

基于新型Nd∶Gd_(0.1)Y_(0.9)AlO_(3)晶体的540 nm倍频绿光激光器EI北大核心CSCD

本工作首次在新型Nd∶Gd_(0.1)Y_(0.9)AlO_(3)(Nd∶GYAP)晶体上实现了540 nm倍频绿光激光器。Nd∶GYAP晶体产生在1μm波段的基频激光中心波长为1079.4 nm,在此基础上利用LBO晶体产生的倍频绿色激光的中心波长为539.4 nm,阈值为46 mW,最大输出功率为65 mW。这一激光系统产生的约为540 nm的绿色激光相较于传统Nd离子掺杂的晶体1064 nm激光倍频而来的532 nm绿色激光,可以有效地避开Nd^(3+)位于530 nm附近的吸收峰。因此,具有更长波长、发射峰位于约540 nm处的绿色激光器可以使激光输出更有效,并扩展绿色激光器的应用。     

LDA抽运Nd:YAG/KTP腔内和频589 nm连续波激光器

报道了一种激光二极管阵列（LDA）抽运Nd:YAG双波长和频黄光激光器黄激光是由Nd:YAG晶体的1064 nm和1319 nm谱线腔内和频产生以KTP为和频晶体,采用Ⅱ类临界相位匹配,在12 W的808 nm抽运功率下,获得了最高功率为430 mW连续波基横模的589 nm黄激光输出,光光转换效率为3.6%,光束质量因子M2<1.2实验结果表明采用激光二极管阵列抽运Nd:YAG/KTP腔内和频技术是获得黄激光的高效方法,并可以应用到其它激光增益介质的两条谱线进行腔内和频,获得更多不同颜色的单谱线激光输出     

Ti原子315nm-321nm区（1+1）共振增强多光子电离谱的实验研究

结合激光烧蚀、超声射流技术,在实验上制备了高浓度的Ti原子自由原子束源,测定了315nm-321nm光谱区过渡金属Ti原子的(1+1)共振增强多光子电离谱,并对光谱结构进行了归属.     

LD泵浦全固态608.1nm和频激光器

本文报道了一种全固态腔内和频608.1 nm激光器。在激光谐振腔两个分臂中,两支激光二极管分别泵浦Nd: YVO₄和Nd: YAG晶体,分别选择1 342 nm波长(Nd: YVO₄晶体的⁴F_3/2-⁴I_13/2谱线)与1 112 nm波长(Nd: YAG晶体的⁴F_3/2-⁴I_11/2谱线)振荡并进行腔内和频。通过优化谐振腔设计,腔内两个波长获得了较好的模式匹配。在两个分臂的交叠部分,利用LBO I类相位匹配进行和频,获得和频608.1 nm激光输出。实验表明,当Nd: YVO₄与Nd: YAG晶体泵浦功率分别为600和740 mW时,获得了功率为23.8 mW、波长为608.1 nm激光输出,激光输出稳定、噪声低。利用本文提出的和频结构是获得608.1 nm激光输出较为有效的方法。     

基于激光器激射特性的新型应变传感系统

报道了一种基于掺铒光纤激光器瞬态特性的新型应变传感系统.用光纤环反射镜和光纤Bragg光栅(FBG)构成Fabry-Perot线型腔.腔内插入一个长周期光纤光栅(LPG)，其透射谱的中心波长为1574.4nm.FBG的带宽为0.23nm，不受力时其反射波长为1557.98nm，位于LPG的透射谱左沿；当FBG受力时激射波长向长波方向移动，激光通过LPG时透射损耗增大，腔损耗的增加将使激光激射延迟时间增加.因此，应变的大小可以通过激光产生的延迟时间来测量.这种新型应变传感器的分辨率和灵敏度由抽运光脉冲的高、 关键词： 应变传感 光纤激光器 时域测量 光纤Bragg光栅     

激光波长对煤激光诱导击穿光谱特性影响的试验研究

我国电站入炉煤种复杂多变,实时快速获取煤质成分对保障锅炉的安全、高效、低污染运行具有重大意义。将激光诱导击穿光谱(LIBS)技术应用于燃煤煤质测量,观测了不同波长激光(355,532和1 064 nm)诱导产生的等离子体时间演变特性和不同电离特性元素的谱线时间特性,对比了出现屏蔽效应时的能量阈值随激光波长的变化特征,并研究了激光波长对煤LIBS光谱特性的影响规律。结果发现：使用532 nm激光作为激发光源时,煤LIBS光谱具有最强的谱线信号强度,且出现等离子体屏蔽效应的能量阈值也较高,是一种较理想的激发光源,为LIBS技术在煤质测量领域的工业应用提供了实验依据。     

423—475nm的激光作用下呋喃分子的多光子电离离解研究

在波长为423—475nm的激光作用下对呋喃分子的多光子电离离解过程进行了研究.在此实验波段内,呋喃分子主要经历的是(3+1)多光子过程.得到了呋喃分子的共振多光子电离分质量谱以及离子强度与激光强度的关系.对共振多光子电离谱峰进行了里德堡态标识. 关键词：     

闪光灯泵浦的可调谐镁橄榄石激光器

一、前言最近,可调谐固态激光器领域取得了显著进展。在各种可调谐激光晶体中,掺铬镁橄榄石(Cr:Mg_2SiO_4)由于其激光波长和泵浦源更引人注目。据报道,镁橄榄石可以在1230nm附近产生激光,可以用Nd:YAG激光器(1064nm)激励这种晶体,获得高效率的泵浦。     

一种新颖的实现纳米条纹沉积方法研究

利用近共振激光驻波场操纵中性原子实现纳米量级条纹沉积技术是一种新型的研制纳米结构长度传递标准的方法,采用了一种新颖的方法,通过预准直孔的设定,将原子束在空间分成三部分,利用中间部分的原子束和近共振激光驻波场相互作用,在激光驻波场辐射压力作用下使原子按照特定周期沉积在基板上,从而实现纳米条纹的制作.利用两侧部分的原子束与探测激光束相互作用,通过其感生荧光来监测中间部分原子束沉积过程中的准直效果,从而为原子的沉积过程提供实时的原子束特性监测.最后对纳米沉积条纹在经由三狭缝预准直结构作用前后的效果进行了三维仿真,结果表明,未采用该三狭缝预准直结构时,纳米沉积条纹的半高宽为32nm,对比度为8∶1,而采用该三狭缝预准直结构之后,纳米沉积条纹的半高宽为6.2nm,对比度为28∶1,大大提高了纳米沉积条纹的质量.     

Second harmonic 423-nm laser generated by BIBO crystal for calcium optical frequency standard

Calcium is one prospective element for the modern optical frequency standard.The 423-nm transition line of calcium atoms has been widely used in laser slowing and laser cooling, the precise spectrum measurement, and the magnetic optical trapping (MOT).However, there is no any available commercial diode laser working at this wavelength.We built a 423-nm laser based on extra bow-tie cavity and by using a Brewster cut uncoated BIBO (BiB3O6) crystal, which worked at room temperature, with conversion efficiency of 3.75%, and a potential up to 20%.     

A diode-laser optical frequency standard based on laser-cooled Ca atoms: Sub-kilohertz spectroscopy by optical shelving detection

We report an optical frequency standard at 657 nm based on laser-cooled/trapped Ca atoms. The system consists of a novel, compact magneto-optic trap which uses 50 mW of frequency-doubled diode laser light at 423 nm and can trap >10⁷ Ca atoms in 20 ms. High resolution spectroscopy on this atomic sample using the narrow 657 nm intercombination line resolves linewidths (FWHM) as narrow as 400 Hz, the natural linewidth of the transition. The spectroscopic signal-to-noise ratio is enhanced by an order of magnitude with the implementation of a “shelving" detection scheme on the 423 nm transition. Our present apparatus achieves a fractional frequency instability of in 1 s with a potential atom shot-noise-limited performance of and excellent prospects for high accuracy. Received 2 November 1998     

Efficient cooling and trapping of strontium atoms

We report the capture of cold strontium atoms in a magneto-optical trap (MOT) at a rate of 4 x 10(10) atoms/s. The MOT is loaded from an atomic beam decelerated by a Zeeman slower operating with a focused laser beam. The 461-nm laser, used for both cooling and trapping, was generated by sum-frequency mixing in a KTP crystal with diode lasers at 813 nm and a Nd:YAG laser at 1064 nm. As much as 115 mW of blue light was obtained.     

Two-color photoionization of calcium using SHG and LED light

We present a photoionization method to load single ⁴⁰Ca ions in a linear Paul trap from an atomic beam. Neutral Ca I atoms are resonantly excited from the ground state to the intermediate 4s4p ¹P₁-level using coherent 423 nm radiation produced by single-pass second harmonic generation in a periodically poled KTiOPO₄ crystal pumped with an 120 mW extended-cavity diode laser. Ionization is then attained with a high-power light emitting diode imaged to the trap center, using an appropriately designed optical system composed of standard achromatic doublet lenses. The setup simplifies previous implementations at similar efficiency, and it hardly requires any maintenance at all.     

Frequency stabilization of a 399-nm laser by modulation transfer spectroscopy in an ytterbium hollow cathode lamp

The modulation transfer spectroscopy in an ytterbium hollow cathode lamp at 399 nm is measured. The error signal for frequency locking is optimized by measuring the dependences of its slope, linewidth and magnitude on various parameters. Under the optimum condition, the laser frequency at 399 nm can be stabilized. The long-term stability of laser frequency is measured by monitoring the fluorescence signal of the ytterbium atomic beam induced by the locked laser. The laser frequency is shown to be tightly locked, and the stabilized laser is successfully applied to the cooling of ytterbium atoms.     

Atomic gallium laser spectroscopy with violet/blue diode lasers

We describe the operation of two GaN-based diode lasers for the laser spectroscopy of gallium at 403 nm and 417 nm. Their use in an external cavity configuration has enabled us to investigate of absorption spectroscopy in a gallium hollow cathode. We have analyzed the Doppler-broadened profiles, accounting for hyperfine and isotope structure and extracting both the temperature and density of the neutral atomic sample produced in the glow discharge. We have also built a setup to produce a thermal atomic beam of gallium. By using the GaN-based diode lasers, we have studied the laser-induced fluorescence and hyperfine-resolved spectra of gallium. PACS 42.55.Px; 42.60.-v; 32.30.-r; 03.75.Be     

Reducing the first-order Doppler shift in a Sagnac interferometer

We demonstrate a technique to reduce first-order Doppler shifts in crossed atomic/molecular and laser beam setups by aligning two counterpropagating laser beams as part of a Sagnac interferometer. Interference fringes on the exit port of the interferometer reveal minute deviations from perfect antiparallelism. Residual Doppler shifts of this method scale with the ratio v/(4d) of the typical atomic/molecular velocity v and the laser beam diameter d. The method is implemented for precision frequency calibration studies at deep-UV wavelengths, both in one- and two-photon excitation schemes: the 6s(2) --> 6s30p(3/2)J=1 line in Yb at 199 nm and the 4p(6) --> 4p(5)p[1/2](0) transition in Kr at lambda=212 nm. The achieved precision of 6 x 10(-10) is limited by the characteristics of the laser system.     

高功率脉冲电子束辐照SiO$lt;sub$gt;2$lt;/sub$gt;的光学和激光损伤性能

研究了不同剂量的60 kW高功率脉冲电子束辐照对高纯熔石英玻璃的微观结构、光学性能和激光损伤特性的影响规律. 光学显微图像表明, 辐照后熔石英样品由于热效应导致表面破裂, 裂纹密度和尺寸随辐照剂量增加而增大, 采用原子力显微镜分析表面裂纹的微观形貌, 裂纹宽度约1 um, 同时样品表面分布着大量尺寸约0.1–1μm的碎片颗粒. 吸收光谱测试表明, 所有样品均在394 nm处出现微弱的吸收峰, 吸收强度随着电子束辐照剂量增大呈现先增加后减小的趋势. 荧光光谱测试发现辐照前后样品均有3个荧光带, 分别位于460, 494和520 nm, 荧光强度随辐照剂量的变化趋势与吸收光谱一致. 利用355 nm激光研究了不同剂量电子束辐照对熔石英激光损伤阈值的影响, 结果表明熔石英的损伤阈值随着辐照剂量的增加而降低. 在剂量较低时, 导致熔石英激光损伤阈值下降的原因主要是色心缺陷; 剂量较高时, 导致损伤阈值降低的原因主要是样品表面产生的大量微裂纹和碎片颗粒对激光的调制和吸收. 关键词： 熔石英 电子束辐照 色心 激光损伤阈值     

铀原子单色三光子共振增强电离

利用Ｎｄ：ＹＡＧ激光泵浦的脉冲染料激光、原子束装置和飞行时间分辩质谱仪在６０２．７－６２１．０ｎｍ光谱范围内测量了铀原子单色三光子电离光谱。