Profiling and screening analysis of 27 aromatic amino acids by capillary electrophoresis in dual modes

An efficient capillary electrophoretic (CE) profiling and screening system based on dual modes of capillary zone electrophoresis (CZE) and micellar electrokinetic capillary chromatography (MEKC) was developed for the simultaneous determination of 23 nonprotein amino acids (NPAAs) and 4 protein amino acids with aromatic moiety. It involves separation by an uncoated fused-silica capillary under phosphoric acid buffer in CZE mode and by another uncoated fused-silica capillary under neutral sodium dihydrogen phosphate buffer containing sodium dodecyl sulfate in MEKC mode. Migration orders of the amino acids studied on the two separation modes under each optimum condition were very different. The repeatability of migration times measured by the CZE and MEKC was found to be better than 4.8 and 3.4%, respectively, thereby enabling to cross-check the identification of each amino acid. The method linearity and limit of detection of the CZE for each amino acid were found to be adequate for the assay of aromatic amino acids. When the present CE profiling and screening analysis in dual modes was applied to plant seeds, NPAAs such as mimosine from Mimosa pudica Linné, and 2-phenylglycine from Lindera erythrocarpa Makino were positively detected along with tryptophan, phenylalanine and tyrosine.     

Continuous on-line derivatization and selective separation of D-aspartic acid by a capillary electrophoresis system with a continuous sample introduction interface

A rapid and selective method is described for the separation of D-aspartic acid (D-Asp) using a continuous on-line derivatization system coupled to capillary electrophoresis (CE). D-Asp was derivatized using o-phthaldialdehyde/N-acetyl-L-cysteine (OPA/NAC). By on-line derivatization, amino acid enantiomers were automatically and reproducibly converted to the UV-absorbing diastereomer derivatives which were separated by capillary zone electrophoresis (CZE) in the presence of 10 mmol/L beta-cyclodextrin (beta-CD). Under the investigated separation conditions, D-Asp is resolved from L-aspartic acid (L-Asp) and other amino acids in a standard mixture of amino acids. The separation could be achieved within 4 min and the sample throughput rate can reach up to 16 h(-1). The repeatability (defined as relative standard deviation, RSD) was 3.21%, 3.58% with peak area evaluation and 3.72%, 4.03% with peak height evaluation for L-Asp and D-Asp.     

Comparative study of capillary zone electrophoresis and micellar electrokinetic chromatography for the separation of twelve aromatic sulphonate compounds

Summary Two modes of capillary electrophoresis (CE), capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC), were investigated for the separation of 12 aromatic sulphonate compounds. In CZE, although the voltage applied, the buffer concentration and the pH were optimized for effective separation of the compounds studied, under the best conditions four of the five amino compounds coeluted, as did naphthalene-1-sulphonic acid and naphthalene-2-sulphonic acid. In MEKC, sodium dodecyl sulphate (SDS) and Brij 35 were chosen as the anionic and nonionic surfactants and the effect of the concentration of micelles was examined. The effect of adding methanol as the organic modifier was also investigated with each of these micellar systems. All the analytes, including the isomers, were completely separated by use of MEKC with Brij 35 but when SDS was used only 11 compounds were separated because two amino compounds coeluted.     

Potential of Capillary Electrophoresis for the Profiling of Propolis

The usefulness of capillary electrophoresis (CE) with diode array detection for the profiling of Propolis, a hive product, is investigated. Water extracts of Propolis were analyzed with both capillary zone electrophoresis (CZE) at pH 7.0 and 9.3, and micellar electrokinetic chromatography (MEKC) with sodium dodecyl sulfate at pH 9.3. Characteristic profiles were obtained and several organic acids and preservatives could be identified by means of library comparison of the recorded UV spectra combined with addition of reference compounds to the extracts. The selectivity of the CZE and MEKC system differed considerably but the information obtained with both methods was similar. The dry residues of the water extraction were extracted with ethanol-water (70 : 30, v/v) and analyzed with the MEKC system to enable the separation of the more hydrophobic constituents of the Propolis samples. Complex profiles containing various well separated peaks were obtained allowing the identification of some interesting flavonoids. On the basis of the recorded CZE and MEKC profiles, the Propolis samples could be divided into two clearly different groups which are probably from a different origin.     

Continuous on-line derivatization and determination of amino acids by a microfluidic capillary electrophoresis system with a continuous sample introduction interface

An automatic, rapid and continuous on-line derivatization system coupled to microfluidic capillary electrophoresis (CE) for the determination of amino acids using o-phthaldialdehyde/N-acetyl-l-cysteine (OPA/NAC) as the derivative agents has been developed. By on-line derivatization, amino acids were automatically and reproducibly converted to the UV-absorbing derivatives, which were separated by capillary zone electrophoresis (CZE). Optimization of derivatization and separation condition was carried out to achieve both good sensitivity and separation efficiency. The separation could be achieved within 4 min and sample throughput rate can reach up to 16 h⁻¹. The repeatability (defined as relative standard deviation, R.S.D.) was 2.56, 2.85, 3.24 and 3.60% with peak area evaluation and 2.93, 3.12, 4.20 and 4.91% with peak height evaluation for arginine (Arg), phenylalanine (Phe), serine (Ser) and glycine (Gly), respectively. The limits of detection (S/N=3) were 10.46, 13.14, 34.39 and 44.79 μmol/l for Arg, Phe, Ser and Gly, respectively. Major advantages of the proposed method include improved precision and efficient automation of the derivatization by the FI system and the enhanced sampling frequencies by the combined FI-CE system.     

Enantioseparation of chiral aromatic amino acids by capillary electrophoresis in neutral and charged cyclodextrin selector modes

Simultaneous enantioseparations of 15 racemic aromatic amino acids and L-mimosine for their chiral discrimination were achieved by neutral selector-modified capillary electrophoresis (CE) and by charged selector-modified CE. Among the diverse cyclodextrins (CDs) examined, hydroxypropyl (HP)-alpha-CD as the neutral selector and highly sulfated (HS)-gamma-CD as the charged selector provided best chiral environments of different enantioselectivities. Fairly good enantiomeric resolutions were achieved with the HP-alpha-CD mode except for racemic 6-hydroxy-3,4-dihydroxyphenylalanine, threo-3,4-dihydroxyphenylserine and homophenylalanine while high-resolution separations of all the enantiomeric pairs were achieved in the HS-gamma-CD mode except that L-mimosine was not detected and a partial resolution (0.6) for threo-3,4-dihydroxyphenylserine enantiomers. Relative migration times to that of internal standard under the respective optimum conditions were characteristic of each enantiomer with good precision (% RSD: 0.7-3.8), thereby enabling to cross-check the chemical identification of aromatic amino acids and also their chiralities. The method linearity was found to be adequate (r> 0.99) for the chiral assay of the aromatic amino acids investigated. When applied to extracts of three plant seeds, nonprotein amino acids such as L-mimosine (42 nug/g) from Mimosa pudica Linné, and L-3,4-dihydroxyphenylalanine (268 nug/g) from Vicia faba were positively detected along with L-tryptophan, L-phenylalanine and L-tyrosine.     

Determination of nonsteroidal anti-inflammatory drugs in human specimens by capillary zone electrophoresis and micellar electrokinetic chromatography

Therapeutic drug monitoring of anti-inflammatory drugs is necessary for the identification of the agents that cause toxic events and for the decision on the treatment for intoxication. Recently, capillary electrophoresis (CE) has been developed for the simple and rapid analyses of a variety of chemical agents. Micellar electrokinetic chromatography (MEKC) can separate acidic, neutral and basic anti-inflammatory drugs in serum. Furthermore, serum samples are directly applied to the CE system without any pretreatments, and some anti-inflammatory drugs can be separated from serum albumin in the MEKC analysis. On the other hand, capillary zone electrophoresis (CZE) enables us to determine a few microg/mL levels of acidic anti-inflammatory drugs with simple running buffer and stacking technique. A rapid and simultaneous determination of several analgesic anti-inflammatory agents, including ibuprofen, acetaminophen, indomethacin, and salicylic acid in human serum has been developed by using CZE. Therefore, the CZE and MEKC analysis may become a potentially useful alternative to high-performance liquid chromatography (HPLC) and fluorescence polarization immunoassay (FPIA) for therapeutic drug monitoring, particularly in serum of patients suffering from intoxication by overdosage of nonsteroidal anti-inflammatory agents.     

毛细管电泳在手性氨基酸拆分中的研究进展

毛细管电泳(capillary electrophoresis,CE)作为一种强有力的手性分离技术,由于操作简单、试剂消耗少及柱效高等优点,受到广泛关注,是近年来手性分离领域的研究热点.氨基酸是组成蛋白质的基本单元,且大多数氨基酸具有手性中心,手性氨基酸是生命体系的一个重要特征.具有手性中心的氨基酸,其对映体间的生物活性往往存在着较大的差异,因此,氨基酸的手性拆分对了解人体及动物生命活动起着举足轻重的作用.主要总结了近5年来毛细管电泳的3种分离模式(毛细管区带电泳、胶束电动毛细管色谱、毛细管电色谱)在氨基酸手性拆分中的发展和应用.     

Determination of amino acids in tobacco samples by capillary electrophoresis/indirect absorbance detection with isolation of the electrolysis compartment and p-Aminobenzoic acid as a background electrolyte.

A fast, convenient and sensitive method of capillary zone electrophoresis (CZE) and indirect UV detection was proposed for the determination of 16 amino acids. p-Aminobenzoic acid (PAB) was selected as a background electrolyte (BGE). An isolated cell included a BGE buffer part and an electrode buffer one, which were jointed with a glass frit. The isolated cell can prevent PAB from the electrode reaction and improve the stability of the detection baseline. The separation conditions of amino acids were investigated, such as different BGEs, BGE concentration, buffer pH and electroosmotic flow (EOF) modifiers. Under the selected separation conditions, 14 amino acid peaks could be separated in 12 min. The detection limits of the amino acids were in the range of 1.7 - 4.5 micromol/L. The isolated cell is suitable for reagents reacting on the electrodes in capillary electrophoresis. The proposed method has been successfully applied to the determination of the amino acids in tobacco samples.     

Multi-purpose capillary electrophoresis system with concentration gradient detection

A robust, inexpensive and versatile capillary electrophoresis (CE) system for routine and rapid analysis is reported, which consists of a rugged cartridge holding a 20-mum i.d. 15-cm long capillary, and an inexpensive, universal and sensitive concentration gradient detector. The design of the cartridge simplifies the sample introduction process and makes it possible to perform many separation modes, including moving boundary capillary electrophoresis (MBCE), capillary zone electrophoresis (CZE), capillary isotachophoresis (CITP) and capillary isoelectric focusing (CIEF), on the same system. This arrangement provides more information about a sample's components since analytes can be separated by different modes performed on the same CE system. The detector only consists of a low-power HeNe laser, or laser diode, and a photodiode position sensor. Amino acids and proteins of 10(-6)-10(-3)M concentration can be separated by different capillary electrophoretic modes, and detected directly by the detector. The universal detector shows particularly good sensitivity when applied to CE separation modes having self-concentration and focusing effects. Femtomoles of proteins were separated and detected with CIEF. In addition, a short and narrow capillary allows use of high electrical fields which facilitate rapid separations. Four amino acids at millimolar concentrations were fully separated and detected in less than 80 sec by the MBCE mode when a high electric field was applied. The physical size of the whole system is much smaller than that of conventional CE instruments with UV absorbance or fluorescence detector.     

Continuous wave-based multiphoton excitation fluorescence for capillary electrophoresis

It was reported that a novel detection method, continuous wave (CW)-based multiphoton excitation (MPE) fluorescence detection with diode laser (DL), has been firstly proposed for capillary electrophoresis (CE). Special design of end-column detection configuration proved to be superior to on-column type, considering the detection sensitivity. Three different kinds of fluorescent tags that were widely used as molecular label in bio-analysis, such as small-molecule dye, fluorescent protein and nano particle or also referred to as quantum dot (QD), have been evaluated as samples for the constructed detection scheme. Quantitative analyses were also performed using rhodamine species as tests, which revealed dynamic linear range over two orders of magnitude, with detection limit down to zeptomole-level. Simultaneous detection of fluorescent dyestuffs with divergent excitation and emission wavelengths in a broad range showed advantage of this scheme over conventional laser-induced fluorescence (LIF) detection. Further investigations on CW-MPE fluorescence detection with diode laser for capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC) separations of fluorescein isothiocyanate (FITC) labeled amino acids indicated good prospect of this detection approach in various micro or nano-column liquid phase separation technologies.     

Rapid simultaneous determination of alkylxanthines by CZE and its application in analysis of pharmaceuticals and food samples

Capillary electrophoresis (CE) offers the possibility of fast, cheap and reproducible separations for pharmaceutical preparations. Alkylxanthines make up a family of compounds that are used in the treatment and prevention of bronchi asthma and chronic pulmonary disease. The group of analysed compounds include caffeine, dyphylline, theophylline, theobromine and enprofylline. This paper shows a simple capillary zone electrophoretic (CZE) method for separation of this group of xanthines. Using 20 mM borate buffer at pH 9.4 as running buffer at 55 °C it was possible to complete a total separation of a sample in 2 min. Limits of detection in the range 1.9-2.5 mg l⁻¹ were achieved with %R.S.D. of 0.06-0.22% (n = 5). The technique is applied to a range of samples containing the analytes, including tablets and chocolate. Reproducibility (%R.S.D.) of the chocolate analysis technique by CZE was less than 4.5%.     

Combining capillary electrophoresis with mass spectrometry for applications in proteomics

Mass spectrometry (MS)-based proteomics is currently dominated by the analysis of peptides originating either from digestion of proteins separated by two-dimensional gel electrophoresis (2-DE) or from global digestion; the simple peptide mixtures obtained from digestion of gel-separated proteins do not usually require further separation, while the complex peptide mixtures obtained by global digestion are most frequently separated by chromatographic techniques. Capillary electrophoresis (CE) provides alternatives to 2-DE for protein separation and alternatives to chromatography for peptide separation. This review attempts to elucidate how the most promising CE modes, capillary zone electrophoresis (CZE) and capillary isoelectric focusing (CIEF), might best be applied to MS-based proteomics. CE-MS interfacing, mass analyzer performance, column coating to minimize analyte adsorption, and sample stacking for CZE are considered prior to examining numerous applications. Finally, multidimensional systems that incorporate CE techniques are examined; CZE often finds use as a fast, final dimension before ionization for MS, while CIEF, being an equilibrium technique, is well-suited to being the first dimension in automated fractionation systems.     

Ion-interaction-capillary zone electrophoresis of cationic proteomic peptide standards

We have employed a novel capillary electrophoresis (CE) approach recently developed in our laboratory, termed ion-interaction-capillary zone electrophoresis (II-CZE), to the resolution of a mixture of 27 synthetic cationic proteomic peptide standards. These peptides were comprised of three groups of nine peptides (with net charges of +1, +2 and +3 for all nine peptides within a group), the hydrophobicity of the nine peptides within a group varying only subtly between adjacent peptides. This bidimensional CE approach achieved excellent resolution of the peptides with high peak capacity by combining the powerful CZE mechanism located in the background electrolyte (BGE) with an hydrophobicity-based mechanism also located in the BGE, the latter consisting of high concentrations (up to 0.4M) of aqueous perfluorinated acids (trifluoroacetic acid, pentafluoropropionic acid and heptafluorobutyric acid). Thus, concomitant with a CZE separation of the three differently charged groups of peptides, there is an hydrophobically-mediated separation of the peptides within these groups effected through interaction of the hydrophobic anions of the perfluorinated acids with hydrophobic amino acid side-chains in the peptides. This methodology is dramatically different from other CE methods that have used complexing agents such as micelles or cyclodextrins in MEKC. Overall, the results presented here demonstrate the value of CE as a peptide separative tool in its own right, including its use for proteomic applications, and not merely as a complementary technique to reversed-phase high-performance liquid chromatography (RP-HPLC).     

Recent developments in capillary electrophoresis-mass spectrometry of proteins and peptides.

Many researchers have invested considerable efforts toward improving capillary electrophoresis (CE)-mass spectrometry (MS) systems so they can be applied better to standard analyses. This review highlights the developments in CE-MS of proteins and peptides over the last five years. It includes the developments in interfaces, sample-enrichment techniques, microfabricated devices, and some applications, largely in capillary zone electrophoresis (CZE), capillary isoelectric focusing (CIEF) and capillary isotachophoresis formats.     

Chiral Separation by Capillary Zone Electrophoresis Used Cyclodextrins and Their Derivatives as Chiral Selector

Capillary zone electrophoresis (CZE) is a very pronising analytical technique for the optical isomer resolution of the compounds studied. The drawbacks of the techniques such as HPLC [1] were sophisticated stationary phases and/or the relatively high quantity of the chiral agent in the mobile phase, which do not exist in CZE. The capillary electrophoresis (CE) method can offer advantages on lower consumption of analyte and background electrolyte (BGE), shorter analysis time, and higher efficiencies [2-3]     

Analysis of synthetic chemical drugs in adulterated Chinese medicines by capillary electrophoresis/electrospray ionization mass spectrometry

Sixteen synthetic chemical drugs, often found in adulterated Chinese medicines, were studied by capillary electrophoresis/UV absorbance (CE/UV) and capillary electrophoresis/electrospray ionization mass spectrometry (CE/ESI-MS). Only nine peaks were detected with CZE/UV, but on-line CZE/MS provided clear identification for most compounds. For a real sample of a Chinese medicinal preparation, a few adulterants were identified by their migration times and protonated molecular ions. For coeluting compounds, more reliable identification was achieved by MS/MS in selected reaction monitoring mode. Micellar electrokinetic chromatography (MEKC) using sodium dodecyl sulfate (SDS) provided better separation than capillary zone electrophoresis (CZE), and, under optimal conditions, fourteen peaks were detected using UV detection. In ESI, the interference of SDS was less severe in positive ion mode than in negative ion mode. Up to 20 mM SDS could be used in direct coupling of MEKC with ESI-MS if the mass spectrometer was operated in positive ion mode. Because of better resolution in MEKC, adulterants can be identified without the use of MS/MS.     

Cover Picture: Electrophoresis 2'2011

Issue no. 2 is a regular issue assembled of 16 solid and original research articles distributed over 3 distinct parts. Part I is on novel trends in fundamentals and methodologies including theoretical models for selectivity of charged solutes in MEKC, system peaks in indirect detection, measuring epimerization constants by MEEKC, bundled CE using micro‐structured fibers, 2‐D separations by coupling CIEF and CEC, high speed DNA CE, MCE of N‐glycans and mucin expression in a microfluidic gradient device. Part II is concerned with detection, sensitivity enhancement, on‐column preconcentration and microdialysis sampling involving the design of continuous full filling CEC‐ESI‐MS using nanoparticles, CE‐fluorescence using tapered optical fiber, CZE separation of pesticide residues in water samples with acid‐assisted on‐column preconcentration and CE‐LIF to detect neurotransmitter amino acids and carbamathione in brain microdialysis samples. Novel methods for the separation and profiling of various proteins and large nucleic fragments are described in 4 consecutive papers grouped in part III. Featured articles include: Theoretical models of separation selectivity for charged compounds in micellar electrokinetic chromatography (( 10.1002/elps.201000405 )) Bundled capillary electrophoresis using microstructured fibres ( 10.1002/elps.201000442 )) Two‐dimensional separation system by on‐line hyphenation of capillary isoelectric focusing with pressurized capillary electrochromatography for peptide and protein mapping ( 10.1002/elps.201000419 )) Microchip electrophoresis of N‐glycans on serpentine separation channels with asymmetrically tapered turns ( 10.1002/elps.201000461 ))     

Capillary electrophoresis method for the analysis of inorganic anions, organic acids, amino acids, nucleotides, carbohydrates and other anionic compounds.

A previously developed capillary zone electrophoresis (CZE) method with indirect UV detection for the simultaneous determination of inorganic and organic anions, amino acids and carbohydrates using 20 mM 2,6-pyridinedicarboxylic acid (PDC) as the background electrolyte was extended to allow determination of 206 anions including those above--mentioned and physiological amino acids, nucleotides, aromatic acids, haloacetic acids, alcohols, phosphorylated saccharides, oxyhalides, metal oxoacids, metal-ethylenediaminetetraacetic acid (EDTA) complexes, forensic anions, Good's buffers and herbicides. Every compound could be analyzed and their electrophoretic mobility determined simply by selecting detection wavelength. This method is simple and universal for anion analysis, and could be readily applied to the simultaneous determination of anionic compounds. In this work, it was used to identify and quantify important anions in sea urchin and sake.     

Characterization and application of a new ultraviolet derivatization reagent for amino acids analysis in capillary electrophoresis

A new ultraviolet (UV) labeling reagent, p-acetamidobenzenesulfonyl fluoride (PAABS-F), was designed and synthesized to label and determine the amino acids by capillary electrophoresis (CE) with diode-array detector (DAD). PAABS-F is very stable and easy to synthesize. It reacted with primary or secondary amino acids very quickly under facile conditions to give corresponding derivatives in high yield with excellent sensitivity and stability. No by-products were observed in amino acid derivatives when stored at room temperature under natural daylight for at least 7 days. Both amino acids standard solution and real samples reacted with this new UV labeling reagent smoothly to form high UV-absorption derivatives. The labeled 20 standard amino acids were efficiently separated by CE and the mass detection limits (S/N = 3) were ranged from 59.3 fmol for l-tryptophan to 1.70 pmol for l-histidine.