On the Luminescence of Ce<Superscript>3+</Superscript>, Eu<Superscript>3+</Superscript>, and Tb<Superscript>3+</Superscript> in Novel Borate LiSr<Subscript>4</Subscript>(BO<Subscript>3</Subscript>)<Subscript>3</Subscript>

This paper reports on the photoluminescence (PL) and time-resolved properties of Ce³⁺, Eu³⁺, and Tb³⁺ in novel LiSr₄(BO₃)₃ powder phosphors. Ce³⁺ shows an emission band peaking at 420 nm under 350-nm UV excitation. Energy transfer from Ce³⁺ to Mn²⁺ takes place in the co-doped samples. Eu³⁺ shows red emission under near UV excitation. LiSr₄(BO₃)₃:Eu³⁺ phosphor could be a suitable candidate for phosphor-converted solid state lighting. The luminescence lifetime is 2.13 ms for Eu³⁺ in LiSr₄(BO₃)₃:0.001Eu³⁺. As Eu³⁺ concentration increasing, the decay curves deviate from exponential behavior. Tb³⁺ shows the strongest ⁵D₄→⁷ F₅ emission line at 540 nm. Decay curves of ⁵D₄→⁷ F₅ and ⁵D₃→⁷ F₅ emission with different Tb³⁺ concentrations were also measured. Cross-relaxation process is discussed based on the decay curves.     

Synthesis and luminescent properties of Eu<Superscript>3+</Superscript>- and Eu<Superscript>2+</Superscript>-activated sodium pyrophosphate Na<Subscript>4</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

The luminescent properties of Eu³⁺ and Eu²⁺ ions in sodium pyrophosphate, Na₄P₂O₇, have been studied. The excitation spectrum of the Eu³⁺ emission in Na₄P₂O₇ consists of several sets of bands in the range 280–535 nm due to 4f–4f transitions of Eu³⁺ ions and a broad band with a maximum at about 240 nm interpreted to be due to a charge transfer (CT) transition from oxygen 2p states to empty states of the Eu³⁺ 4f⁶-configuration. Although the CT band energy is large enough, the quantum efficiency (η) of the Eu³⁺ emission in Na₄P₂O₇ under CT excitation was estimated to be very low (η ≤ 0.01). In terms of a configurational coordinate model, this fact is interpreted as a result of the high efficiency of a radiationless relaxation from the CT state to the ⁷F₀ ground state of Eu³⁺ ions occupying sodium sites in Na₄P₂O₇. A strong reducing agent is required in order to stabilize Eu²⁺ ions in Na₄P₂O₇ during the synthesis. Several nonequivalent Eu²⁺ luminescence centers in Na₄P₂O₇ were found.     

Morphology-dependent luminescence behavior of Y<Subscript>2-x</Subscript>Gd<Subscript>x</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> thin-film phosphors grown by a laser ablation

Y_2-xGd_xO₃:Eu³⁺ luminescent thin films have been grown on Al₂O₃(0001) substrates using pulsed laser deposition. Films grown under different deposition conditions have been characterized using microstructural and luminescence measurements. The crystallinity, surface morphology and photoluminescence (PL) of the films are highly dependent on the amount of Gd present. The photoluminescence (PL) brightness data obtained from Y_2-xGd_xO₃:Eu³⁺ films grown under optimized conditions have indicated that Al₂O₃(0001) is one of the most promising substrates for the growth of high-quality Y_2-xGd_xO₃:Eu³⁺ thin-film red phosphors. In particular, the incorporation of Gd into the Y₂O₃ lattice could induce a remarkable increase of PL. The highest emission intensity was observed with Y_1.35Gd_0.60Eu_0.05O₃, whose brightness was increased by a factor of 3.1 in comparison with that of Y₂O₃:Eu³⁺ films. This phosphor may be promising for application in flat-panel displays. PACS 78.20.-e; 78.55.-m; 78.66.-w     

Correction of the band gap of Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> phosphor

Submicron samples of Y₂O₃:Eu³⁺ phosphor with elevated photoluminescence (PL) efficiency and activator concentration of 9 at % obtained by the sol–gel method were investigated by diffuse reflection spectroscopy and PL spectroscopy. It is found that the diffuse reflection spectrum in the vicinity of the fundamental absorption edge (<300 nm) is distorted by the superposition of the PL of Eu³⁺ ions, as a result of which the calculated value of optical band gap E _g of the Y₂O₃ matrix is overestimated. An algorithm for eliminating the PL influence on the absorption edge is proposed, and the correct E _g values are found to be 4.61 ± 0.12 and 4.50 ± 0.12 eV for annealing at 700 and 1300°C, respectively.     

luminescence of BaGa<Subscript>2</Subscript>Se<Subscript>4</Subscript> crystals activated by Eu<Superscript>2+</Superscript> and Ce<Superscript>3+</Superscript> ions

We have studied the effect of doping with Eu²⁺ and Ce³⁺ ions on the photoluminescence (PL) of BaGa₂Se₄ crystals in the temperature range 77–300 K. We have established that the broad bands with maxima at wavelengths 456 nm and 506 nm observed in the photoluminescence spectra of BaGa₂Se₄:Ce³⁺ crystals are due to intracenter transitions 5d → ²F_7/2 and 5d →²F_5/2 of the Ce³⁺ ions, while the broad photoluminescence band with maximum at 521 nm in the spectrum of BaGa₂Se₄:Eu²⁺ is associated with 4f⁶ 5d → 4f⁷ (⁸S_7/2) transitions of the Eu²⁺ ion. We show that in BaGa₂Se₄:Eu²⁺,Ce³⁺ crystals, excitation energy is transferred from the Ce³⁺ ions to the Eu²⁺ ions.     

Red,Yellow, Blue and Green Emission from Eu<Superscript>3+</Superscript>, Dy<Superscript>3+</Superscript> and Bi<Superscript>3+</Superscript> Doped Y<Subscript>2</Subscript>O<Subscript>3</Subscript>nano-Phosphors

Rare earth elements (RE = Eu³⁺& Dy³⁺)and Bi³⁺ doped Y₂O₃ nanoparticles were synthesized by urea hydrolysis method in ethylene glycol, which acts as reaction medium as well as a capping agent, at a low temperature of 140 °C,followed by calcination of the obtained product. Transmission electron microscope (TEM) images reveals that ovoid shaped Y₂O₃ nanoparticles of around 22–24 nm size range were obtained in this method. The respective RE and Bi³⁺ doped Y₂O₃ precursor nanoparticles when heated at 600 and 750 °C, retains the same shape as that of the as-synthesized Y₂O₃ precursor samples. From EDAX spectra, the incorporation of RE ions into the host has been studied. XRD pattern reveals the crystalline nature of the heated nanoparticles and indicate the absence of any impurity phase other than cubic Y₂O₃.However, the as-synthesized nanoparticles were highly amorphous without the presence of any sharp XRD peaks. Photoluminescence study suggests that the synthesized samples could be used as red (Eu³⁺), yellow (Dy³⁺), blue and green (Bi³⁺)emitting phosphors.     

The Role of the Eu<Superscript>3+</Superscript> Concentration on the SrMoO<Subscript>4</Subscript>:Eu Phosphor Properties: Synthesis,Characterization and Photophysical Studies

SrMoO₄ doped with rare earth are still scarce nowadays and have attracted great attention due to their applications as scintillating materials in electro-optical like solid-state lasers and optical fibers, for instance. In this work Sr_1−xEu_xMoO₄ powders, where x = 0.01; 0.03 and 0.05, were synthesized by Complex Polymerization (CP) Method. The structural and optical properties of the SrMoO₄:Eu³⁺ were analyzed by powder X-ray diffraction patterns, Fourier Transform Infra-Red (FTIR), Raman Spectroscopy, and through Photoluminescent Measurements (PL). Only a crystalline scheelite-type phase was obtained when the powders were heat-treated at 800 °C for 2 h, 2θ = 27.8° (100% peak). The excitation spectra of the SrMoO₄:Eu³⁺ (λ_Em. = 614 nm) presented the characteristic band of the Eu^3 + 5L₆ transition at 394 nm and a broad band at around 288 nm ascribed to the charge-transfer from the O (2p) state to the Mo (4d) one in the SrMoO₄ matrix. The emission spectra of the SrMoO₄:Eu³⁺ powders (λ_Exc. = 394 and 288 nm) show the group of sharp emission bands among 523–554 nm and 578–699 nm, assigned to the ⁵D₁→⁷F_{0,1and 2} and ⁵D₀→⁷F_{0,1,2,3 and 4}, respectively. The band related to the ⁵D₀→⁷F₀ transition indicates the presence of Eu³⁺ site without inversion center. This hypothesis is strengthened by the fact that the band referent to the ⁵D₀→⁷F₂ transition is the most intense in the emission spectra.     

Luminescence thermometry using Gd<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript>

In this paper we study the possibility of using the synthesized nanopowder samples of Gd₂Zr₂O₇:Eu³⁺ for temperature measurements by analyzing the temperature effects on its photoluminescence. The nanopowder was prepared by solution combustion synthesis method. The photoluminescence spectra used for analysis of Gd₂Zr₂O₇:Eu³⁺ nano phosphor optical emission temperature dependence were acquired using continuous laser diode excitation at 405 nm. The temperature dependencies of line emission intensities of transitions from ⁵D₀ and ⁵D₁ energy levels to the ground state were analyzed. Based on this analysis we use the two lines intensity ratio method for temperature sensing. Our results show that the synthesized material can be efficiently used as thermographic phosphor up to 650 K.     

Synthesis and characterization of mono-dispersed Y<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript>:Er<Superscript>3+</Superscript>-coated SiO<Subscript>2</Subscript> nanoparticles by co-precipitation process

In this paper, a facile co-precipitation process for preparing mono-dispersed core–shell structure nanoparticles is reported. The 110 nm SiO₂ cores coated with an yttrium aluminum garnet (Y₃Al₅O₁₂) layer doped with Er³⁺ were synthesized and the influence of the concentration ratio of [urea]/[metal ions] on the final product was investigated. The structure and morphology of samples were characterized by the X-ray powder diffraction, Fourier transform IR spectroscopy and transmission electron microscopy, respectively. The results indicate that a layer of well-crystallized garnet Y₃Al₅O₁₂:Er³⁺ were successfully coated on the silica particles with the thickness of 20 nm. The near infrared and upconversion luminescent spectra of the SiO₂@Y₃Al₅O₁₂:Er³⁺ powders further confirm that a Y₃Al₅O₁₂:Er³⁺ coating layer has formed on the surface of silica spherical particles.     

Intense White Luminescence from Combustion Synthesized Ca<Subscript>12</Subscript>Al<Subscript>14</Subscript>O<Subscript>33</Subscript>: Yb<Superscript>3+</Superscript>/Yb<Superscript>2+</Superscript> Single Phase Phosphor

The Ca₁₂Al₁₄O₃₃: Yb³⁺/Yb²⁺ single phase nano-phosphor has been synthesized through combustion route and its luminescence and lifetime studies have been carried out up to 20 K using 976 and 266 nm excitations. The samples heated in open atmosphere have shown the presence of Yb in Yb³⁺ and Yb²⁺ states. The 976 nm excitation results a cooperative upconversion emission at 486 nm due to the Yb³⁺ state and a broad band in the blue region and has been assigned to arise from the defect centers. The 266 nm excitation on the other hand results a broad emission band even from as-synthesized phosphor without doping of Yb, the width of which increases in presence of Yb due to the emission from Yb²⁺ ions formed in heated samples. The white emission covers almost whole visible region with bandwidth 190 nm. The ions in Yb²⁺ state has been found to increase with the increase in heating temperature up to 1,273 K. A back conversion of Yb²⁺ to Yb³⁺ has been observed for higher temperatures. Effect of boric and phosphoric acids as flux on the emission properties of Yb³⁺ and Yb²⁺ states have been examined and discussed. Quantum yield of emission has also been determined for different samples.     

Luminescence characteristics of energy transfer between Ce<Superscript>3+</Superscript> and Eu<Superscript>2+</Superscript> in NaMgPO<Subscript>4</Subscript> phosphor

Powder samples of NaMgPO₄ doped with Eu²⁺ and Ce³⁺ were prepared and their photoluminescence spectra were systemically studied. Energy transfer from Ce³⁺ to Eu²⁺ in NaMgPO₄ phosphor was observed by investigating the optical properties from photoluminescence spectra in Eu²⁺ or Ce³⁺ singly doped and Eu²⁺–Ce³⁺ codoped sodium magnesium orthophosphates, NaMgPO₄. The enhancement of UV excitation is attributed to energy transfer from Ce³⁺ to Eu²⁺, and Ce³⁺ plays a role as a sensitizer. Ce³⁺–Eu²⁺ codoped NaMgPO₄ phosphors in which Eu²⁺ can be efficiently excited by 390 nm are potential candidates for phosphor-converted LEDs.     

Improved photoluminescence of pulsed-laser-ablated Y<Subscript>1-x</Subscript>Gd<Subscript>x</Subscript>VO<Subscript>4</Subscript>:Eu<Superscript>3+</Superscript> thin film phosphors by Gd substitution

Gd-substituted Y_1-xGd_xVO₄:Eu³⁺ luminescent thin films have been grown on Al₂O₃(0001) substrates using pulsed-laser deposition. The films grown under different deposition conditions have been characterized using microstructural and luminescent measurements. The crystallinity, surface morphology, and photoluminescence (PL) of the films are highly dependent on the amount of Gd. The photoluminescence (PL) brightness data obtained from Y_1-xGd_xVO₄:Eu³⁺ films grown under optimized conditions have indicated that the PL brightness is more dependent on the surface roughness than the crystallinity of the films. In particular, the incorporation of Gd into the YVO₄ lattice could induce a remarkable increase of PL. The highest emission intensity was observed with Y_0.57Gd_0.40Eu_0.03VO₄ thin film whose brightness was increased by a factor of 2.5 and 1.9 in comparison with that of YVO₄:Eu³⁺ and GdVO₄:Eu³⁺ films, respectively. This phosphor have application to flat panel displays. PACS 78.20.-e; 78.55.-m; 78.66.-w     

Luminescence in Dy<Superscript>3+</Superscript> and Eu<Superscript>3+</Superscript> Activated K<Subscript>3</Subscript>Al<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

The Dy³⁺ and Eu³⁺ activated K₃Al₂ (PO₄)₃ phosphors were prepared by a combustion synthesis. From a powder X-ray diffraction (XRD) analysis the formation of K₃Al₂ (PO₄)₃ was confirmed. In the photoluminescence emission spectra, the K₃Al₂(PO₄)₃:Dy³⁺ phosphor emits two distinctive colors: blue and yellow whereas K₃Al₂(PO₄)₃:Eu³⁺ emits red color. Thus the combination of colors gives BYR (blue–yellow–red) emissions can produce white light. These phosphors exhibit a strong absorption between 340 and 400 nm which suggest that present phosphor is a promising candidate for producing white light-emitting diodes (LED).     

Tunable bluish green to yellowish green Ca<Subscript>2(1-x)</Subscript>Sr<Subscript>2x</Subscript>Al<Subscript>2</Subscript>SiO<Subscript>7</Subscript>:Eu<Superscript>2+</Superscript> phosphors for potential LED application

A series of solid solutions with a general formula of Ca_2(1-x)Sr_2xAl₂SiO₇:Eu²⁺ were synthesized by a high temperature solid state reaction. The structure, diffuse reflection spectra, photoluminescence spectra, color-coordinate parameters and lifetimes of phosphors were investigated. XRD results show that Ca₂Al₂SiO₇ is totally miscible with Sr₂Al₂SiO₇. These solid solution phosphors show a broad excitation band of 350–450 nm that matches well with the output lights of near-UV LEDs and tunable emission from bluish green to yellowish green. These optical properties originate from the 4f⁷–4f⁶5d transition of Eu²⁺ ions. The crystal field strength was considered to be tailed by controlling the host composition, which leads to the shift of absorption band and emission band, and the varying of color coordinates. PACS  78.55.-m; 42.70.-a; 61.05.C-     

Synthesis and Optical Characterization of Red-Emitting BaTa<Subscript>2</Subscript>O<Subscript>6</Subscript>:Eu<Superscript>3+</Superscript> Phosphors

Undoped and Eu³⁺ doped BaTa₂O₆ phosphors were synthesized via solid state reaction method and characterized by using XRD, SEM-EDS and photoluminescence (PL) analyses. The XRD results revealed that the crystal structure of BaTa₂O₆ allowed up to 10 mol% levels of Eu³⁺ ions due to the TTB characteristic network of adjacent octahedrals. SEM-EDS analyses confirmed the formation of BaTa₂O₆ structure and EuTaO₄ secondary phase. BaTa₂O_6:Eu³⁺ phosphors exhibited orange and red emissions at 592.2 nm and 615.7 nm in the visible region respectively. The Commission Internationale d’Eclairage (CIE) chromaticity coordinates of the BaTa₂O_6:Eu³⁺ phosphors that excited at λ _ex = 400 nm ranged from orangish-red to pinkish-red depending on increasing Eu³⁺ concentration.     

Synthesis and Optical Properties of Novel Red-Emitting PbNb<Subscript>2</Subscript>O<Subscript>6</Subscript>: Eu<Superscript>3+</Superscript> Phosphors

Undoped and PbNb₂O_6:Eu³⁺ (1.0 ≤ x ≤ 6.0 mol%) phosphors were synthesized at 1100 °C for 3.5 h by the conventional solid state reaction method. Synthesized PbNb₂O₆:Eu³⁺ phosphors were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy dispersive spectroscopy (EDS) and Photoluminescence (PL) analyses. The PL spectra showed series of excitation peaks between 350 and 430 nm due to the 4f–4f transitions of Eu³⁺. For 395.0 nm excitation, emission spectra of Eu³⁺ doped samples were observed at 591 nm (orange) and 614 nm (red) due to the ⁵D₀ → ⁷F₁ transitions and ⁵D₀ → ⁷F₂ transitions, respectively. PL analysis results also showed that the emission intensity increased by increasing Eu³⁺ ion content. No concentration quenching effect was observed. The CIE chromaticity color coordinates (x,y) of the PbNb₂O₆:Eu³⁺ phosphors were found to be in the red region of the chromaticity diagram.     

A novel white light-emitting diode (w-LED) fabricated with Sr<Subscript>6</Subscript>BP<Subscript>5</Subscript>O<Subscript>20</Subscript>:Eu<Superscript>2+</Superscript> phosphor

Sr₆BP₅O₂₀:Eu²⁺ phosphor was prepared by the solid-state reaction method under a weak reductive atmosphere and the photoluminescence properties were studied systematically. The bluish-green emission band of Sr₆BP₅O₂₀:Eu²⁺ phosphor is peaking at 475 nm, and the excitation bands are broad with peaks at about 290 and 365 nm with a shoulder around 390 nm, respectively. By combining with Ga(In)N-based near-ultraviolet LEDs, a bluish-green LED was fabricated based on the Sr₆BP₅O₂₀:Eu²⁺ phosphor, and a novel intense white LED was fabricated based on the bluish-green phosphor Sr₆BP₅O₂₀:Eu²⁺ and the red phosphor (Sr,Ca)₅(PO₄)₃Cl:Eu²⁺,Mn²⁺. When this two-phosphor white LED is operated under 20-mA forward-bias current at room temperature, the Commission Internationale de l’Eclairage(CIE) chromaticity coordinates (x,y), the correlated color temperature Tc, and the color rendering index Ra are calculated to be (0.3281,0.3071), 5687 K, and 87.3, respectively. The dependence of the bluish-green and two-phosphor white LEDs on different forward-bias currents from 5 mA to 50 mA shows a similar behavior. As the current increases, the relative intensity simultaneously increases. The CIE chromaticity coordinates (x,y) of the two-phosphor white LED tend to decrease. Consequently, the correlated color temperature Tc increases from 3800 K to 9400 K and the color rendering index Ra of the two-phosphor white LED increases from 83.4 to 91.8 simultaneously. PACS 07.60.-j; 42.70.-a; 71.55.Eq     

Eu<Superscript>3+</Superscript> As a Luminescent Probe for Studying the Structure of R<Subscript>2</Subscript>O<Subscript>3</Subscript> Materials (R = Y,Eu, and Gd)

Spectra of Eu³⁺ in various dielectric matrices (Gd₂O₃:Eu³⁺, Y₂O₃:Eu³⁺, Eu₂O₃, and mSiO₂/Gd₂O₃:Eu³⁺ mesoporous particles) are studied by local cathodoluminescence. The results allowed identification of the local environment of Er³⁺ ions in amorphous samples and detection of the monoclinic Eu₂O₃ phase impurity in samples with yttrium oxide. The cathodoluminescence spectra of chemically pure Y₂O₃, Eu₂O₃, and Gd₂O₃ are recorded. Conclusions about the structural features of the materials are made and confirmed by other methods (XRD and EPMA).     

Microstructural and Radioluminescence Characteristics of Nd<Superscript>3+</Superscript> Doped Columbite-Type SrNb<Subscript>2</Subscript>O<Subscript>6</Subscript> Phosphor

Undoped and different concentration Nd³⁺ doped SrNb₂O₆ powders with columbite structure were synthesized by molten salt process using a mixture of strontium nitrate and niobium (V) oxide and NaCl-KCl salt mixture as a flux under relatively low calcining temperature. X-ray diffraction analysis results indicated that SrNb₂O₆ phases found to be orthorhombic columbite single phase for undoped, 0.5 and 3 mol% Nd³⁺ doping concentrations. Phase composition of the powders was examined by SEM-EDS analyses. Radioluminescence properties of Nd³⁺ doped samples from UV to near-IR spectral region were studied. The emissions increased with the doping concentration of up to 3 mol%, and then decreased due to concentration quenching effect. There is a sharp emission peak around 880 nm associated with ⁴F_5/2 → ⁴I_9/2 transition in the Nd³⁺ ion between 300 and 1100 nm. The broad emission band intensity was observed from 400 to 650 nm where the peak intensities increased by increasing Nd³⁺ doping concentration. All the measurements were taken under the room temperature.     

Characterization and photoluminescence studies of Eu<Superscript>2+</Superscript>-doped BaSO<Subscript>4</Subscript> phosphor prepared by the recrystallization method

Eu doped BaSO₄ was prepared by the recrystallization method and characterization of the material was done by using X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and Fourier transform infrared spectroscopy (FTIR) techniques. From the XRD pattern of Eu doped BaSO₄ compound, it was found that the prominent phase formed was BaSO₄ and traces of other phases were very weak and the result of FTIR spectrum of BaSO₄:Eu shows that the sulfur-oxygen stretch was found at around 1100 cm⁻¹. The room-temperature PL spectra of the Eu doped BaSO₄ sample showed one peak centered at 374 nm, which is the characteristic emission of Eu²⁺ ion. This emission band at 374 nm corresponds to the 4f⁶ 5d→4f⁷ (⁸S_7/2) transitions of Eu²⁺ ions. The excitation spectrum taken at the wavelength 374 nm extends over a wide range of wavelengths from 220–350 nm with a strong peak at around 260 nm. Furthermore, the present sample shows good crystal quality and high photoluminescence sensitivity. Hence our results suggest possible potential applications of Eu doped BaSO₄ phosphor in optoelectronic devices.