Synthesis and magnetic properties of platelet γ-Fe2O3 particles for medical applications using hysteresis-loss heating

Platelet γ-Fe₂O₃ particles of particle size less than 100 nm were prepared for medical applications that use the hysteresis-loss heating of ferromagnetic particles. The γ-Fe₂O₃ particles were obtained through the dehydration, reduction, and oxidation of platelet α-FeOOH particles, which were synthesized by the precipitation of ferric ions in an alkaline solution containing ethanolamine, and the crystals grown using a hydrothermal treatment. The γ-Fe₂O₃ particles contained dimples formed by the dehydration of α-FeOOH particles. The coercive force and the saturation magnetization of the γ-Fe₂O₃ particles were in the ranges 11.9 to 12.7 kA/m (150 to 160 Oe), and 70 to 72 Am²/kg (70 to 72 emu/g), respectively. The specific loss power of the γ-Fe₂O₃ particles, estimated from their temperature-raising property measured under a peak magnetic field of 50.9 kA/m (640 Oe) and at a frequency of 117 kHz, was 590 W/g. This value is higher than that of spherical cobalt-containing iron oxide particles having equivalent coercive force and saturation magnetization, reflecting the larger area of the minor hysteresis loop measured under a peak magnetic field of 50.9 kA/m (640 Oe).     

Fe fine particles encapsulated by titanium oxides with high magnetization for biomedical application

Iron (Fe) fine particles encapsulated by titanium oxide (TiO₂) were synthesized through a solid-phase reaction. The structure of Fe cores and TiO₂ shells consisted of α-Fe and rutile TiO₂, respectively. The average particle size was 0.8 μm, in which a Fe particle with a diameter of ∼750 nm was encapsulated by a TiO₂ shell with a thickness of ∼100 nm. The Fe particles had a high saturation magnetization of 127 Am²/kg and low coercivity of 1.6 kA/m. They also exhibited excellent corrosion resistance, similar to Fe₃O₄ in a soaking test.     

In vitro corrosion behavior of Ti-O film deposited on fluoride-treated Mg-Zn-Y-Nd alloy

In this paper, a new composite coating was fabricated on magnesium alloy by a two-step approach, to improve the corrosion resistance and biocompatibility of Mg-Zn-Y-Nd alloy. First, fluoride conversion layer was synthesized on magnesium alloy surface by immersion treatment in hydrofluoric acid and then, Ti-O film was deposited on the preceding fluoride layer by magnetron sputtering. FE-SEM images revealed a smooth and uniform surface consisting of aggregated nano-particles with average size of 100 nm, and a total coating thickness of ∼1.5 μm, including an outer Ti-O film of ∼250 nm. The surface EDS and XRD data indicated that the composite coating was mainly composed of crystalline magnesium fluoride (MgF₂), and non-crystalline Ti-O. Potentiodynamic polarization tests revealed that the composite coated sample have a corrosion potential (E_corr) of −1.60 V and a corrosion current density (I_corr) of 0.17 μA/cm², which improved by 100 mV and reduced by two orders of magnitude, compared with the sample only coated by Ti-O. EIS results showed a polarization resistance of 3.98 kΩ cm² for the Ti-O coated sample and 0.42 kΩ cm² for the composite coated sample, giving an improvement of about 100 times. After 72 h immersion in SBF, widespread damage and deep corrosion holes were observed on the Ti-O coated sample surface, while the integrity of composite coating remained well after 7 d. In brief, the data suggested that single Ti-O film on degradable magnesium alloys was apt to become failure prematurely in corrosion environment. Ti-O film deposited on fluoride-treated magnesium alloys might potentially meet the requirements for future clinical magnesium alloy stent application.     

Synthesis and hyperthermia property of hydroxyapatite-ferrite hybrid particles by ultrasonic spray pyrolysis

Biocompatible hybrid particles composed of hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂, HAp) and ferrite (γ-Fe₂O₃ and Fe₃O₄) were synthesized using a two-step procedure. First, the ferrite particles were synthesized by co-precipitation. Second, the suspension, which was composed of ferrite particles by a co-precipitation method, Ca(NO₃)₂, and H₃PO₄ aqueous solution with surfactant, was nebulized into mist ultrasonically. Then the mist was pyrolyzed at 1000 °C to synthesize HAp-ferrite hybrid particles. The molar ratio of Fe ion and HAp was (Fe²⁺ and Fe³⁺)/HAp=6. The synthesized hybrid particle was round and dimpled, and the average diameter of a secondary particle was 740 nm. The cross section of the synthesized hybrid particles revealed two phases: HAp and ferrite. The ferrite was coated with HAp. The synthesized hybrid particles show a saturation magnetization of 11.8 emu/g. The net saturation magnetization of the ferrite component was calculated as 32.5 emu/g. The temperature increase in the AC-magnetic field (370 kHz, 1.77 kA/m) was 9 °C with 3.4 g (the ferrite component was 1.0 g). These results show that synthesized hybrid particles are biocompatible and might be useful for magnetic transport and hyperthermia studies.     

Improvement in magnetic properties of La substituted BaFe12O19 particles prepared with an unusually low Fe/Ba molar ratio

In this study, effect of lanthanum substitution on the phase composition, lattice parameters and magnetic properties of barium hexaferrite has been studied in samples synthesized in ammonium nitrate melt. Samples, prepared with different lanthanum amount and having various initial Fe/(Ba+La) ratios in between 12 and 2 {(Ba_1−xLa_x)·n Fe₂O₃, where 0≤x≤1 and 1≤n≤6)}, are sintered at temperatures from 800 to 1200 °C. The lattice parameters, both a and c, decreases with increasing La amount which results in a decrease of the unit cell volume. The scanning electron microscope micrographs show that the pure and La-substituted sample with x=0.3, both calcinated at 1000 °C, have grain sizes smaller than 1 μm. The coercivities of the La-substituted samples increase with increasing La amount and reaches to a maximum value of 5.73 kOe, when x=0.3. Sintering at higher temperatures (above 1000 °C) decreases the coercivity, resembling a transition from single to multi-domain behavior of the particles, while saturation magnetization of the samples continues to increase due to the increasing grain size. Magnetization measurements of the samples prepared with different Fe/(Ba+La) molar ratios, n's, revealed that the specific saturation magnetization slightly increases with decreasing n, while coercivities fluctuates around 5.5 kOe. However, a sharp increase in the saturation magnetization has been observed in the sample having n=1 and washed in HCl. It was measured as 59.2 emu/g at 15 kOe, which is higher than that of the pure sample (57.5 emu/g). Thus, the magnetic parameters are optimized in the sample Ba_0.7La_0.3Fe₁₂O₁₉ so as to maximize both coercivity and specific saturation magnetization in the HCl-washed sample synthesized by starting with an unusually low Fe/(Ba+La) molar ratio of 2 (or n=1).     

Adsorption structure of glycine on TiO2(1 1 0): A photoelectron diffraction determination

High-resolution core-level photoemission and scanned-energy mode photoelectron diffraction (PhD) of the O 1s and N 1s states have been used to investigate the interaction of glycine with the rutile TiO₂(1 1 0) surface. Whilst there is clear evidence for the presence of the zwitterion CH₂COO⁻ with multilayer deposition, at low coverage only the deprotonated glycinate species, NH₂CH₂COO is present. Multiple-scattering simulations of the O 1s PhD data show the glycinate is bonded to the surface through the two carboxylate O atoms which occupy near-atop sites above the five-fold-coordinated surface Ti atoms, with a Ti-O bondlength of 2.12 ± 0.06 Å. Atomic hydrogen arising from the deprotonation is coadsorbed to form hydroxyl species at the bridging oxygen sites with an associated Ti-O bondlength of 2.01 ± 0.03 Å. Absence of any significant PhD modulations of the N 1s emission is consistent with the amino N atom not being involved in the surface bonding, unlike the case of glycinate on Cu(1 1 0) and Cu(1 0 0).     

Ni–Zn–Sm nanopowder ferrites: Morphological aspects and magnetic properties

Ni–Zn ferrites have been widely used in components for high-frequency range applications due to their high electrical resistivity, mechanical strength and chemical stability. Ni–Zn ferrite nanopowders doped with samarium with a nominal composition of Ni_0.5Zn_0.5Fe_2−xSm_xO₄ (x=0.0, 0.05, and 0.1 mol) were obtained by combustion synthesis using nitrates and urea as fuel. The morphological aspects of Ni–Zn–Sm ferrite nanopowders were investigated by X-ray diffraction, nitrogen adsorption by BET, sedimentation, scanning electron microscopy and magnetic properties. The results indicated that the Ni–Zn–Sm ferrite nanopowders were composed of soft agglomerates of nanoparticles with a high surface area (55.8–64.8 m²/g), smaller particles (18–20 nm) and nanocrystallite size particles. The addition of samarium resulted in a reduction of all the magnetic parameters evaluated, namely saturation magnetization (24–40 emu/g), remanent magnetization (2.2–3.5 emu/g) and coercive force (99.3–83.3 Oe).     

Structural and magnetic study of swift heavy ion irradiated W/Fe multilayer structure

The present study reports the effect of swift heavy ion irradiation on structural and magnetic properties of sputtered W/Fe multilayer structure (MLS) having bilayer compositions of [W(10 Å)/Fe(20 Å)]_10BL. The MLS is irradiated by 120 MeV Au⁹⁺ ions of fluences 1×10¹³ and 4×10¹³ ions/cm². Techniques like X-ray reflectivity (XRR), cross-sectional transmission electron microscopy (X-TEM) and DC magnetization with a vibrating sample magnetometer (VSM) are used for structural and magnetic characterization of pristine and irradiated MLS. Analysis of XRR data using Parratt’s formalism shows a significant increase in W/Fe layer roughness. X-TEM studies reveal that intra-layer microstructure of Fe layers in MLS becomes nano-crystalline on irradiation. DC magnetization study shows that with spacer layer thickness interlayer coupling changes between ferromagnetic to antiferromagnetic.     

Model design on calculations of microwave permeability and permittivity of Fe/SiO2 particles with core/shell structure

Fe/SiO₂ particles with core/shell structure were prepared by coating silica on the surface of a commercial spherical carbonyl iron via the hydrolysis process of tetraethyl orthosilicate (TEOS). The electromagnetic performance of commercial carbonyl iron and as-prepared Fe/SiO₂ particles was studied theoretically and experimentally. As predicted by the theoretical calculation based on the Bruggeman formula and the Landau–Lifshitz–Gilbert (LLG) theory, the insulating surface layer of silica was effective to reduce the permittivity parameters of pure carbonyl iron. The measured results showed good agreement with the theoretical prediction. Although there was a little decrease in the permeability of the Fe/SiO₂ core/shell particles, a better impedance match especially at higher frequency range was obtained when used as a microwave absorber. The reflection loss (RL) curves show that the lowest reflection loss of Fe/Epoxy composite (−20.5 GHz) was obtained corresponding to the frequency of 8.5 GHz when the thickness of the absorber was 3 mm. A different trend was observed in Fe/SiO₂/Epoxy composite. The reflection loss value got lower by decreasing the thickness of absorbers. At the thickness of 2.2 mm, a relative low reflection loss (−17 GHz) corresponding to the frequency of 13.6 GHz was obtained. Compared with the Fe/Epoxy composite, the improvement on shifting the reflection loss peak to higher frequency and on reducing the optimal thickness of absorbers was made by Fe/SiO₂/Epoxy composite.     

Preparation and chemical stability of iron-nitride-coated iron microparticles

Iron-nitride-coated iron microparticles were prepared by nitridation of the surface of iron microparticles with ammonia gas at a temperature of 510 °C. The phases, composition, morphology, magnetic properties, and chemical stability of the particles were studied. The phases were α-Fe, ε-Fe₃N, and γ-Fe₄N. The composition varied from the core to the surface, with 99.8 wt% Fe in the core, and 93.8 wt% Fe and 6 wt% N in the iron-nitride coating. The thickness of the iron-nitride coating was about 0.28 μm. The chemical stability of the microparticles was greatly improved, especially the corrosion resistance in corrosive aqueous media. The saturation magnetization and the coercive force were 17.1×10³ and 68 kA/m, respectively. It can be concluded that iron-nitride-coated iron microparticles will be very useful in many fields, such as water-based magnetorheological fluids and polishing fluids.     

Synthesis of iron oxide nanoparticles under oxidizing environment and their stabilization in aqueous and non-aqueous media

Synthesis of magnetite (Fe₃O₄) nanoparticles under oxidizing environment by precipitation from aqueous media is not straightforward because Fe²⁺ gets oxidized to Fe³⁺ and thus the ratio of Fe³⁺:Fe²⁺=2:1 is not maintained during the precipitation. A molar ratio of Fe³⁺:Fe²⁺ smaller than 2:1 has been used by many to compensate for the oxidation of Fe²⁺ during the preparation. In this work, we have prepared iron oxide nanoparticles in air environment by the precipitation technique using initial molar ratios Fe³⁺:Fe²⁺?2:1. The phases of the resulting powders have been determined by several techniques. It is found that the particles consist mainly of maghemite with little or no magnetite phase. The particles have been suspended in non-aqueous and aqueous media by coating the particles with a single layer and a bilayer of oleic acid, respectively. The particle sizes, morphology and the magnetic properties of the particles and the ferrofulids prepared from these particles are reported. The average particle sizes obtained from the TEM micrographs are 14, 10 and 9 nm for the water, kerosene and dodecane-based ferrofluids, respectively, indicating a better dispersion in the non-aqueous media. The specific saturation magnetization (σ_s) value of the oleic-acid-coated particles (∼53 emu/g) is found to be lower than that for the uncoated particles (∼63 emu/g). Magnetization σ_s of the dodecane-based ferrofluid is found to be 10.1 emu/g for a volume fraction of particles ?=0.019. Zero coercivity and zero remanance on the magnetization curves indicate that the particles are superparamagnetic (SPM) in nature.     

Study of polydiethylsiloxane-based ferrofluid with excellent frost resistance property

The polydiethylsiloxane-based ferrofluid was prepared by dispersing finely divided magnetic Fe₃O₄ particles which are modified with oleoyl sarcosine and lauroyl sarcosine. The optimized experiment parameters including molar ratio of surfactant to Fe₃O₄ (1:5), temperature (80 °C), stirring rate (300 RPM), the surfactant content of lauroyl sarcosine (0 to 33 mol%) and the modification time (25 min) were obtained by the orthogonal test. The magnetic liquid was characterized by a transmission electron microscope (TEM), infrared (IR) spectrometer, X-ray diffractometer (XRD), thermogravimetry (TG), vibrating sample magnetometer (VSM) and differential scanning calorimetry (DSC). It is indicated that the surfactant is mainly bonded to the surface of Fe₃O₄ nanoparticles through covalent bond between carboxylate (COO⁻) and Fe atom. The modified magnetic particles are equally dispersed into the carrier and remain stable below −12 °C over 4 months. The ferrofluids exhibit excellent frost resistance property and distinctly reduced temperature coefficient of viscosity compared with polydimethylsiloxane-based ferrofluids and hydrocarbon-based ferrofluids, respectively. The saturation magnetization could reach up to 27.7 emu/g.     

Mixed-metal carbonates as precursors for the synthesis of nanocrystalline Mn-Zn ferrites

A mixed Mn-Zn-Fe carbonate was prepared by precipitation of metal ions with ammonium carbonate and control of pH=7. Nanocrystalline Mn-Zn ferrite powders were synthesized by thermal decomposition of the carbonate precursor at 500 °C in air. The mean crystallite size of the ferrite particles is 14 nm with a specific surface of 74 m²/g. The magnetization at 5 K of the Mn-Zn ferrite powders (66 emu/g) is smaller than the saturation magnetization of the bulk material. Hysteresis loop measurements indicate ferrimagnetic behavior at 5 and 298 K with a small coercivity at room temperature.     

Cationic starch as a precursor to prepare porous activated carbon for application in supercapacitor electrodes

Three activated carbons (ACs) for the electrodes of supercapacitor were prepared from cationic starch using KOH, ZnCl₂ and ZnCl₂/CO₂ activation. The BET surface area, pore volume and pore size distribution of the ACs were evaluated using density functional theory method, based on N₂ adsorption isotherms at 77 K. The surface morphology was characterized with SEM. Their electrochemical performance in prototype capacitors was determined by galvanostatic charge/discharge characteristics and cyclic voltammetry, and compared with that of a commercial AC, which was especially prepared for use in supercapacitors. The KOH-activated starch AC presented higher BET surface area (3332 m² g⁻¹) and larger pore volume (1.585 cm³ g⁻¹) than those of the others, and had a different surface morphology. When used for the electrodes of supercapacitors, it exhibited excellent capacitance characteristics in 30 wt% KOH aqueous electrolytes and showed a high specific capacitance of 238 F g⁻¹ at 370 mA g⁻¹, which was nearly twice that of the commercial AC.     

Microstructures and multiferroic properties of textured Bi0.8La0.2FeO3 thin films

La-substituted BiFeO₃, Bi_0.8La_0.2FeO₃, thin films were fabricated on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and high-resolution transmission electron microscope were used to analyze the structures of the films. The results show the films fabricated under optimized growth condition are (0 1 2) textured. X-ray photoemission spectroscopy results indicate that the oxidation state of Fe ion is Fe³⁺ in the films without detectable Fe²⁺. The films show low leakage current and excellent dielectric characters. Multiferroic properties with a remnant ferroelectric polarization of 5.2 μC/cm² and a remanent magnetization of 0.02 μ_B/Fe were established. These results have some implications for further research.     

Morphological, structural and adsorption features of oxide composites with silica and titania matrices

Morphological, structural, electronic, and adsorption characteristics of complex oxides such as fumed silica/alumina and silica/titania, fumed silica with deposited oxides of Mg, Ti, Mn, Ni, Cu, Zn and Zr, silica gel with grafted ZrO₂, sol-gel titania doped by 3d-metals (Cr, Fe, Mn, V) were compared using adsorption, TEM, AFM, XRD, XPS, Mössbauer and Raman spectroscopy data. It was shown that surface, volume, and phase compositions of oxides, particle size distributions (5 nm-3 μm), specific surface area (S_BET ∼ 50-500 m²/g), and porosity (V_P ∼ 0.1-2 cm³/g) affected by synthesis technique and subsequent treatment determine electronic structure (bandgap, valence band and core levels structure) of the materials, adsorption of molecules and metal ions as well as other characteristics.     

Mechanical and magnetic properties of ZnO/Fe2O3 ceramic varistors

Mechanical and magnetic properties of the ZnO/Fe₂O₃ ceramic varistors have been examined by using mechanical analyzer, digital microhardness tester and vibrating sample magnetometer. The initial stress–strain behavior is found to be linear (elastic) then becomes nonlinear (plastic deformation) without reaching the failure limit up to the maximum available stress (0.07 MPa). The compressive elastic modulus varies between 0.2 and 0.8 MPa with Fe addition up to 0.50. Furthermore, an approximately monotonically linear decrease in VHN with increasing Fe content up to 50% has been observed for all applied loads, which closely resembles the behavior of the true hardness and the surface energy. The magnetic measurements revealed an antiferromagnetic to paramagnetic to transition for all Fe doped samples. The Fe free sample showed paramagnetic behavior down to 2 K. The Neel temperature moderately increased from 18 K at 0.05% Fe to 25 K at 0.5% Fe. The magnetization (M) versus applied magnetic field (H) did not reach saturation for all samples up to 9 Tesla. The saturated magnetization (per Fe contents) is low and found to decreases linearly at a rate of (−35 emu/g-Fe) in a clear manifestation of the strengthening of the antiferromagnetic exchange interaction with increasing Fe contents.     

Synthesis and magnetic properties of the size-controlled Mn-Zn ferrite nanoparticles by oxidation method

Size-controlled Mn_0.67Zn_0.33Fe₂O₄ nanoparticles in the wide range from 80 to 20 nm have been synthesized, for the first time, using the oxidation method. It has been demonstrated that the particle size can be tailor-made by varying the concentration of the oxidant. The magnetization of the 80 nm particles was 49 A m² kg⁻¹ compared to 34 A m² kg⁻¹ for the 20 nm particles. The Curie temperatures for all the samples are found to be within 630±5 K suggesting that there is no size-dependent cation distribution. The critical particle size for the superparamagnetic limit is found to be about 25 nm. The effective magnetic anisotropy constant is experimentally determined to be 7.78 kJ m⁻³ for the 25 nm particles, which is about an order of magnitude higher than that of the bulk ferrite.     

Size-controlled synthesis of superparamagnetic iron oxide nanoparticles and their surface coating by gold for biomedical applications

The size mono-dispersity, saturation magnetization, and surface chemistry of magnetic nanoparticles (NPs) are recognized as critical factors for efficient biomedical applications. Here, we performed modified water-in-oil inverse nano-emulsion procedure for preparation of stable colloidal superparamagnetic iron oxide NPs (SPIONs) with high saturation magnetization. To achieve mono-dispersed SPIONs, optimization process was probed on several important factors including molar ratio of iron salts [Fe³⁺ and Fe²⁺], the concentration of ammonium hydroxide as reducing agent, and molar ratio of water to surfactant. The biocompatibility of the obtained NPs, at various concentrations, was evaluated via MTT (3-(4, 5-dimethylthiazol-2-yl)-2, 5-diphenyltetrazolium bromide) assay and the results showed that the NPs were non-toxic at concentrations <0.1 mg/mL. Surface functionalization was performed by conformal coating of the NPs with a thin shell of gold (∼4 nm) through chemical reduction of attached gold salts at the surface of the SPIONs. The Fe₃O₄ core/Au shell particles demonstrate strong plasmon resonance absorption and can be separated from solution using an external magnetic field. Experimental data from both physical and chemical determinations of the changes in particle size, surface plasmon resonance optical band, phase components, core–shell surface composition, and magnetic properties have confirmed the formation of the mono-dispersed core–shell nanostructure.     

Structural, electronic properties and stability of the (1 × 1) PbTiO3 (1 1 1) polar surfaces by first-principles calculations

Under GGA, the structural, electronic properties and stabilities of four different (1 × 1) terminations of cubic PbTiO₃ (1 1 1) surface, the directly cleaved (1 1 1)-Ti and (1 1 1)-PbO₃ terminations and the constructed (1 1 1)-TiO and (1 1 1)-PbO₂ ones, have been systematically studied by using projector-augmented wave method implemented in VASP. For (1 1 1)-Ti and (1 1 1)-PbO₃ terminations, Ti-O bonds between the outermost two layers are enhanced after relaxation, while those between the second and the third layers are weakened. In addition, a contraction of O-O distance in surface PbO₃ layer is also found for (1 1 1)-PbO₃ termination. Moreover, electronic structures of both (1 1 1)-Ti and (1 1 1)-PbO₂ terminations are significantly influenced by structure relaxations, and the effects of the surface on the DOS are dominantly on the Ti layers, especially the CB. For a constructed (1 1 1)-TiO termination, the relaxation results show both Ti-O bonds between the outermost two layers and those between the second PbO₃ layer and the third Ti layers are enhanced. For a constructed (1 1 1)-PbO₂ termination, Ti-O bonds between the outermost two layers are also enhanced as in the (1 1 1)-TiO termination, however, inequivalent Ti-O bonds between the second layer Ti atom and the third layer O atoms are found, with two bonds expanding and the other one contracting. Results of electronic structure calculations show these two constructed terminations are all insulating and changes of DOS originate dominantly from modifications of surface compositions. Furthermore, it is found that for all four different (1 1 1) terminations, the movements of the cation and/or anion on the outermost layer along the surface normal direction after relaxation all result in a reduction of the space electric field. In O and Pb external environments, it is predicted that (1 1 1)-PbO₂ termination is the most stable one in O- and Pb-rich environments, however, the (1 1 1)-Ti termination is stable one in O- and Pb-poor conditions. The (1 1 1)-TiO termination also shows a stability domain in moderate O and Pb environments.