高性能注入锁相光电振荡器

提出一种基于注入锁定和锁相环技术的注入锁相光电振荡器.利用注入锁定来改善光电振荡器的近载频相噪以及杂散抑制度.将光电振荡器的输出信号与外注入源进行鉴相,通过锁相环来提升频率稳定性,并进一步改善光电振荡器的近载频相噪.实验结果表明:注入锁相光电振荡器在电滤波器中心频率为9.5GHz、3dB带宽为20 MHz和光纤环长度为6km的情况下,实现了输出信号频率为9.5GHz的单模振荡;当注入锁定带宽为1.98kHz时,光电振荡器输出信号在1kHz频偏处的相位噪声为-125dBc/Hz,在10kHz频偏处的相位噪声为-147dBc/Hz,杂散抑制度高于80dB,阿伦偏差接近1.37×10~(-11)@1s和1.22×10~(-11)@1000s.     

通过锁相使一种过模复合器件运行频率稳定

 提出了一种过模复合器件。自洽地导出了由外电磁信号和预群聚电子束同时驱动的一种过模复合器件的辐射波相位锁定方程；讨论了到达锁相运行的时间、频率移动和带宽。分析表明：当由预群聚电子束和外电磁信号同时锁相时，通过调节参数，可以缩短到达锁相运行的时间，减小运行频率对要锁定的频率（外电磁信号频率）的移动和增大锁相运行的带宽。     

锁频锁相的高功率微波器件技术研究

综述了中国工程物理研究院应用电子学研究所锁频锁相的高功率微波器件最新研究成果,主要包括稳频稳相的相对论速调管放大器和注入锁相的相对论返波管振荡器.针对高功率长脉冲相对论速调管研究中遇到的问题,介绍了该放大器的束波互作用特点、杂频振荡抑制、脉冲缩短、高频段高功率运行、高增益等物理、设计与实验中的关键技术研究概况,使其功率、相位稳定性、增益等性能有了显著提高,S波段环形单注相对论速调管实现了高功率稳相输出,重频25 Hz运行时输出功率大于1 GW,脉宽大于150 ns、相位波动18°,高增益运行时在注入微波功率数kW条件下也实现类似功率和相位水平;采用同轴多注器件结构,突破了速调管高频段运行条件下高效率电子束引入和高功率束波转换技术等难题,使X波段相对论速调管在注入功率30 kW条件下实现了功率大于1 GW的放大输出,效率为34%,相位波动为15°.在掌握相对论返波管技术的基础上,利用返波管的高效率和结构紧凑的优点,开展了注入调制电子束锁相的相对论返波管研究,采用百kW级的种子微波实现了对GW量级输出微波的相位锁定.该研究结果对功率合成、粒子加速和多功能雷达等技术具有重要的推动作用.     

Stabilizing the frequency of femtosecond Ti:sapphire comb laser by a novel scheme

We demonstrated a novel scheme for scanning the absolute frequencies of a femtosecond Kerr-lens mode-locked Ti:sapphire laser with the repetition rate unaffected, where the carrier-envelop phase of the pulse was controlled by slightly shifting pump beam and the repetition rate was phase locked to a stable radio-frequency oscillator. Since it was the first time to stabilize the frequency of a mode-locked laser by referring directly to the frequency of cesium two-photon-transition (TPT) stabilized diode laser, we evaluated the frequency instability and the frequency accuracy that showed the characteristic of being a comb laser. The feature of the comb laser in this report will be significant for multi-photon spectroscopy where the frequency difference between comb lines plays a key role. PACS  06.30.+v; 42.60.By     

利用光锁相环路实现40 Gb/s时钟恢复

提出并建立了一种新型的基于光纤四波混频效应和压控光脉冲源的光锁相环路(OPLL),用于光时分复用系统(OTDM)中的时钟恢复过程。从理论上分析了其工作原理,及各模块结构和功能。利用高非线性光纤中的四波混频效应实现全光鉴相器,有效缩短了光纤长度,减小了光纤色散引起的脉冲走离,鉴相器消光比超过30 dB。采用再生锁模光纤激光器实现压控光脉冲源,在保证脉冲质量的前提下,重复频率调节范围达到380 kHz。在40 Gb/s时钟恢复实验中,获得脉宽为7.2 ps、接近变换极限的时钟脉冲,时间抖动(RMS)为152 fs,超模抑制比大于60 dB。实验证明,输入信号幅度波动和码型效应对环路影响很小。     

Subfemtosecond synchronization of microwave oscillators with mode-locked Er-fiber lasers

We synchronize an 8.06 GHz microwave signal from a voltage-controlled oscillator with an optical pulse train from a 77.5 MHz mode-locked Er-fiber laser using a fiber-based optical-microwave phase detector. The residual phase noise between the optical pulse train and the synchronized microwave signal is -133 dBc/Hz (-154 dBc/Hz) at 1 Hz (5 kHz) offset frequency, which results in 838 as integrated rms timing jitter [1 Hz-1 MHz]. The long-term residual phase drift is 847 as (rms) measured over 2 h, which reaches 4×10(-19) fractional frequency instability at 1800 s averaging time. This method has a potential to provide both subfemtosecond-level short-term phase noise and long-term phase stability in microwave extraction from mode-locked fiber lasers.     

Cesium optical atomic clock: an optical pulse that tells the time

We propose a new cesium (Cs) atomic clock whose microwave source is a 9.1926-GHz harmonically and regeneratively mode-locked erbium fiber laser rather than a quartz oscillator and a multiplexer. The repetition rate of the laser is directly locked to the Cs resonance, and the frequency stability evaluated by the Allan variance is 7.1 x 10(-12) for tau = 1 s. This new atomic clock provides not only a precise 1-s time standard after demultiplexing but also an optical pulse train with the same stability, which means that the ultrastable clock signal can be delivered throughout the world by means of optical fiber networks.     

全光纤多种子激光脉冲产生系统

报道一种可精确同步输出宽带啁啾脉冲、纳秒级整形脉冲以及窄带光参量啁啾放大抽运脉冲的全光纤多种子激光脉冲产生系统.采用掺镱光纤锁模激光器和掺镱单纵模光纤振荡器作为系统的光源,将掺镱光纤锁模激光器输出的超短脉冲分束啁啾展宽至0.9ns后,一路进行放大产生10μJ量级的宽带啁啾脉冲为高能拍瓦激光器系统提供种子光脉冲,另一路通过1.2nm滤波产生140ps的基元脉冲,通过光纤堆积器产生可编程整形的2.3ns脉冲,再经过放大达到10μJ量级,提供任意整形的压缩脉冲.同时,将部分掺镱光纤锁模激光器输出的超短脉冲进行光电转换并锁相后,产生与锁模超短脉冲高精度同步的电脉冲用于触发幅度调制器,将掺镱单纵模光纤振荡器输出的连续光削波放大,产生光参量啁啾放大抽运脉冲.该系统能够根据物理实验的需要,非常灵活地在输出各种脉冲之间做出选择.     

频率注入锁定的超再生NQR谱仪

本文首先简述超再生振荡器的频率注入锁定的基本原理,然后介绍一台频率注入锁定的超再生NQR谱仪的工作原理。该谱仪的频稳度高(10^-4-10^-5),频率测量方便,检测谱线线型失真小,可用来观察样品的NQR纯色散和纯吸收谱。文中还给出用本谱仪检测的氯酸钠(NaClO₃)粉末中的³⁵Cl核的NQR纯吸收谱和纯色散谱。     

1-mJ, sub-5-fs carrier–envelope phase-locked pulses

We report the routine generation of sub-5-fs laser pulses with 1-mJ energy and stable carrier–envelope phase at 1-kHz repetition rate, obtained by compressing the multi-mJ output from a phase-locked Ti:sapphire amplifier in a rare-gas-filled hollow fiber. The dual-stage amplifier features a hybrid transmission grating/chirped mirror compressor providing 2.2-mJ, 26-fs pulses at 1 kHz with standard phase deviation of 190 mrad rms. We demonstrate hour-long phase stability without feedback control of grating position or rigorous control of the laser environment, simply by using small pulse stretching factors in the amplifier, which minimize the beam pathway in the compressor. The amplifier also integrates a versatile AOPDF (acousto-optic programmable dispersive filter) for closed-loop spectral phase optimization. The various factors influencing the overall phase stability of the system are discussed in detail. Using the optimized output, 1-mJ, 4.5-fs pulses are generated by seeding the neon gas filled hollow fiber with a circularly polarized input beam. A standard phase deviation of 230 mrad after the HCF is obtained by direct f-to-2f detection and slow-loop feedback to the oscillator locking electronics without any additional spectral broadening.     

一种实现光纤激光器高功率输出的方法

介绍了一种实现光纤激光器高功率输出的新方法——采用螺旋芯光纤，这种光纤是在光纤制作过程中按照一定的弯曲半径使纤芯呈螺旋状排布在光纤包层中。介绍了这种螺旋芯光纤的原理和其提高输出功率的能力，以及目前的理论与实验研究现状。基于该光纤，提出了一种光纤激光器相干合成新思想。     

Noise properties of an optical frequency comb from a SESAM-mode-locked 1.5-μm solid-state laser stabilized to the 10?13 level

We present a detailed investigation of the noise properties of an optical frequency comb generated from a femtosecond diode-pumped solid-state laser operating in the 1.5-??m spectral region. The stabilization of the passively mode-locked Er:Yb:glass laser oscillator, referred to as ERGO, is achieved using pump power modulation for the control of the carrier envelope offset (CEO) frequency and by adjusting the laser cavity length for the control of the repetition rate. The stability and the noise of the ERGO comb are characterized in free-running and in phase-locked operation by measuring the noise properties of the CEO, of the repetition rate, and of a comb line at 1558?nm. The comb line is analyzed from the heterodyne beat signal with a cavity-stabilized ultra-narrow-linewidth laser using a frequency discriminator. Two different schemes to stabilize the comb to a radio-frequency (RF) reference are compared. The comb properties (phase noise, frequency stability) are limited in both cases by the RF oscillator used to stabilize the repetition rate, while the contribution of the CEO is negligible at all Fourier frequencies, as a consequence of the low-noise characteristics of the CEO-beat. A?linewidth of ??150?kHz and a fractional frequency instability of 4.2×10^?13 at 1?s are obtained for an optical comb line at 1558?nm. Improved performance is obtained by stabilizing the comb to an optical reference, which is a cavity-stabilized ultra-narrow linewidth laser at 1558?nm. The fractional frequency stability of 8×10^?14 at 1?s, measured in preliminary experiments, is limited by the reference oscillator used in the frequency comparison.     

非PLL相位平均型参考线原型验证

射频相位参考线是粒子加速器的重要组成部分之一,为射频低电平控制系统(LLRF)、束流诊断系统、定时系统等提供稳定的相位锁定参考信号。为减少远距离传输过程中由环境温度变化导致的射频传输线中的射频相位漂移,多个加速器装置中已经采用射频相位参考线提供射频相位参考,这些相位参考的实现方案主要是基于恒温控制和基于光纤锁相。与这些方案相比,采用相位平均方法不仅可以保持长距离节点之间的相位稳定,而且更易于现场安装与维护。现有的带有锁相环(PLL)的终端短路方式实现相位平均参考线的方案仍有一些节点数量限制等方面的不足,本文对相位平均参考线结构进行了去除PLL的简化设计并进行了验证,以期增加更多的相位分配节点以及降低对射频器件参数的要求。对非PLL的单端输入终端短路相位平均方案与两端输入各节点间互为参考的相位平均方案分别进行了实验测试,结果表明两者的相位RMS精度可以达到0.1°~0.3°。并对不同的相位平均实现方案中相位不稳定的产生原因进行了分析,结果表明,除环境温度外,同轴线缆材质、合成相位与幅度的不平衡合成等也是重要影响因素。     

Theoretical analysis of self-phase locking in a type II phase-matched optical parametric oscillator

We analyze a doubly-resonant type II phase-matched optical parametric oscillator that includes an intracavity waveplate for inducing mutual injection locking between the signal and the idler. The intracavity waveplate provides a linear coupling between the normally orthogonally polarized signal and idler fields and allows for mode locking at frequency degeneracy. Under mode locked conditions the signal–idler phase difference is locked and the optical parametric oscillator becomes self-phase locked. The signal–idler phase can be adjusted by changing the operating point within the locking range. Two self-phase locked modes with different thresholds and signal–idler phases are possible. Characteristics of the self-phase locked regime are presented for different linear coupling strengths.     

自由电子激光的预群聚

研究了自由电子激光预群聚产生的辐射,表明预群聚不仅可以提高效率而且使低增益得到增强,从而在理论上解释了由射频直线加速器驱动的自由电子激光预群聚器(prebuncher)的作用。同时还指出,预群聚有在不增加电子束能量情况下缩短激光波长和降低对电子束质量要求等作用。     

Phase-locked, erbium-fiber-laser-based frequency comb in the near infrared

A phase-locked frequency comb in the near infrared is demonstrated with a mode-locked, erbium-doped, fiber laser whose output is amplified and spectrally broadened in dispersion-flattened, highly nonlinear optical fiber to span from 1100 to >2200 nm. The supercontinuum output comprises a frequency comb with a spacing set by the laser repetition rate and an offset by the carrier-envelope offset frequency, which is detected with the standard f-to-2f heterodyne technique. The comb spacing and offset frequency are phase locked to a stable rf signal with a fiber stretcher in the laser cavity and by control of the pump laser power, respectively. This infrared comb permits frequency metrology experiments in the near infrared in a compact, fiber-laser-based system.     

Phase locking of two long-pulse, high-power magnetrons

We have phase locked a pair of long-pulse, high-power, secondary-emission magnetrons to an RF-isolated low-power driver via a waveguide directional coupler. With the 3 dB hybrid coupler, the peak and average power sent back towards the driver were lower than the total power by factors of 20 and 100, respectively. A dual-channel, thyratron-switched line-type modulator was used to power the magnetrons in parallel. In this experiment the total microwave power from the pair of phase-locked high-power magnetrons was limited to 48 MW for 700 ns pulses and 46 MW for 900 ns pulses because one of the high-power magnetrons would only operate at or below half power. Experimental results from this repetitively-pulsed (10 Hz) phase-locked magnetron pair are presented which show excellent phase stability of several degrees both during the pulse and from pulse-to-pulse     

Precision phase control of an ultrawide-bandwidth femtosecond laser: a network of ultrastable frequency marks across the visible spectrum

We demonstrate that the stability of the current optical frequency comb generated by a Kerr-lens mode-locked femtosecond laser is limited by the microwave reference used for phase locking the comb spacing. Hence we implement precision frequency/phase control of the entire comb to the fundamental and second-harmonic frequencies of a stable cw laser without any external microwave reference. The stability of a cw iodine-stabilized laser is transferred to millions of comb lines (with an instability of 3 x 10(-13)) covering more than one octave of the optical frequency spectrum. In addition, the mode spacing of the comb can be used as a stable microwave frequency derived directly from a stable optical oscillator.     

Coherent combination of high-power, zigzag slab lasers

We demonstrate a scalable architecture for a high-power, high-brightness, solid-state laser based on coherent combinations of master oscillator power amplifier chains. A common master oscillator injects a sequence of multikilowatt Nd:YAG zigzag slab amplifiers. Adaptive optics correct the wavefront of each amplified beamlet. The beamlets are tiled side by side and actively phase locked to form a single output beam. The laser produces 19 kW with beam quality <2x diffraction limited. To the best of our knowledge, this is the brightest cw solid-state laser demonstrated to date.     

Self-phase-locked degenerate femtosecond optical parametric oscillator

We demonstrated a stable degenerate synchronously pumped femtosecond optical parametric oscillator (SPOPO) as a divide-by-2 subharmonic generator. The SPOPO exhibited passive all-optical self-phase-locking between the pump and signal/idler and thus required no external electronic feedback to produce the phase-locked subharmonic. We employed a type I phase-matched, 1-mm-long, periodically poled MgO:LiNbO3 crystal as the nonlinear gain element and an 80 MHz mode-locked Ti:sapphire laser with 180 fs pulses tuned at 775 nm as the pump. The SPOPO generated transform-limited 70 fs phase-locked output pulses centered at 1550 nm. The self-phase-locking operation was confirmed by separate beat-note measurement techniques with respect to the pump laser and with respect to an external cw laser.