利用凝胶渗透色谱示差-紫外检测器联用测定丁苯共聚物的组成分布

将凝胶渗透色谱(GPC)中的示差与紫外检测器联用,测定了无规共聚丁苯橡胶和SBS三元嵌段共聚物中各级分的组成变化.实验方法选择中对比了两种浓度参数的确定方法,发现通过改变注射量来实现浓度变化的方法优于使用系列浓度样品的方法.分别测定标准样品在紫外和示差检测器上信号产生的时间间隔可以确定两个检测器上信号的时间差.根据紫外-示差检测器联用可以看到SBR无规共聚物和三嵌段SBS共聚物样品中每一个级分中随着相对分子质量的变化,苯乙烯含量的变化.     

Determination of volatile phenols in wine using high-performance liquid chromatography with a coulometric array detector

A new high-performance liquid chromatography method using a coulometric array detector to simultaneously analyse 4-ethylphenol, 4-ethylguaiacol, 4-vinylphenol, and 4-vinylguaiacol in wine was established. This procedure offers important advantages as it does not require sample preparation, with the exception of filtration, and performs chromatographic separation in short time, making control of wine production processes easier. The method is linear up to concentrations of 2000 μg L⁻¹ and precise (R.S.D. < 3%). Limits of detection are low (1-3 μg L⁻¹) and suitable for analytical requirements in the oenological field. When compared to gas-chromatography-flame ionisation detection, the proposed method gives similar results with a shorter execution time.     

Maximum entropy deconvolution of secondary ion mass spectra with a measured response

The Maximum Entropy Method (MEM) has, for the first time, been successfully applied for the deconvolution of Secondary Ion Mass Spectra. Phosphorus-doped silicon was used as an analytical system. The commonly used technique to eliminate the interferences between phosphorus and the silicon hydride peaks (measurement at high mass resolution) strongly reduces the signal intensities. With MEM the mass resolution could be increased by a factor of ten without intensity loss. The response was determined by the lineshape of a non-overlapped mass peak of silicon. The validity of this approach was proved by comparison of the MEM solution with high resolution mass spectra.     

Applications of a miniaturized fluorimetric photodiode array detector for capillary liquid chromatography

A high sensitivity, multichannel fluorescence detector with small volume has been developed for capillary column liquid chromatography. Using an intensified linear photodiode array to monitor fluorescence emission, several important mixtures exhibiting native fluorescence have been examined following high efficiency separation on a capillary column. By correlating mass spectral, fluorescence spectral, and retention time data, information of potential utility in the structural elucidation of aromatic molecules contained in complex mixtures can be obtained. Examples include the separation and spectral examination of the polyaromatic compounds in samples of both biological and environmental interest.     

Fused silica capillary tube isotachophoresis using a multichannel photodiode array detector

Isotachophoresis carried out in a 0.25 mm i.d. fused-silica capillary tube yielded high resolution, compared with that in a fluorinated ethylene-propylene polymer tube. The use of an ultraviolet-visible multichannel spectrophotometer with photodiode array as detector together with a cross flow cell (volume 0.01 μl) was investigated. The system was successfully applied to the analysis of cationic dyes such as neutral red, bismarck brown, and basic fuchsine.     

Simultaneous determination of 20 food additives by high performance liquid chromatography with photo-diode array detector

An efficient and accurate analytical method was developed for the simultaneous determination of 20 synthetic food additives, including three sweeteners,seven food colorants,nine synthetic preservatives and caffeine,by high performance liquid chromatography (HPLC) with photodiode array detector(PDA).This method permits the detection of food additives at very low concentrations(0.005-0.150μg/mL).The applicability was verified by the determination of food additives present in various foodstuffs.     

Interpretation of butyltin mass spectra using isotope pattern reconstruction for the accurate measurement of isotope ratios from molecular clusters

The fragmentation patterns of butyltin compounds (mono-, di-, and tributyltin) in an electron impact ion source were studied using an isotope pattern reconstruction algorithm with emphasis on isotope ratio measurements from molecular clusters. For this purpose, standards of natural tin isotope abundance and a (119)Sn-enriched mixture of the three compounds were both ethylated and propylated using sodium tetraalkylborates. The corresponding mass spectra of the various tetraalkyltin compounds prepared were obtained by GC/MS after their extraction with hexane.The results showed that pure interference-free molecular clusters were obtained only for certain R(3)Sn(+) ions where no isobaric overlap with R(2)SnH(+) ions occurred (e.g. BuEt(2)Sn(+) overlaps with Bu(2)SnH(+)). These ions are ideal candidates for accurate Sn isotope ratio measurements, while isotope pattern perturbing interferences are observed for other molecular fragments down to Sn(.)(+). Isotope pattern reconstruction algorithm thus can be used as an analytical tool to ensure the absence of molecular interferences--a requirement for accurate isotope ratio measurements from molecular clusters. The relevance of these studies for the determination of butyltin compounds in environmental samples by isotope dilution GC/MS is also discussed.     

Validation of CE modeling with a contactless conductivity array detector

Dynamic computer simulation data are compared for the first time with CE data obtained with a laboratory made system comprising an array of 8 contactless conductivity detectors (C⁴Ds). The experimental setup featured a 50 μm id linear polyacrylamide (LPA) coated fused‐silica capillary of 70 cm length and a purpose built sequential injection analysis manifold for fluid handling of continuous or discontinuous buffer configurations and sample injection. The LPA coated capillary exhibits a low EOF and the manifold allows the placement of the first detector at about 2.7 cm from the sample inlet. Agreement of simulated electropherograms with experimental data was obtained for the migration and separation of cationic and anionic analyte and system zones in CZE configurations in which EOF and other column properties are constant. For configurations with discontinuous buffer systems, including ITP, experimental data obtained with the array detector revealed that the EOF is not constant. Comparison of simulation and experimental data of ITP systems provided the insight that the EOF can be estimated with an ionic strength dependent model similar to that previously used to describe EOF in fused‐silica capillaries dynamically double coated with Polybrene and poly(vinylsulfonate). For the LPA coated capillaries, the electroosmotic mobility was determined to be 17‐fold smaller compared to the case with the charged double coating. Simulation and array detection provide means for quickly investigating electrophoretic transport and separation properties. Without realistic input parameters, modeling alone is not providing data that match CE results.     

Determination of isotope cluster patterns in mass spectra of GC-MS analyses by a chemometric detector

The computer program ISODET recognizes isotope cluster patterns in the mass spectra of the GC-MS analysis of atoms of chlorine, bromine, sulphur and chlorine/bromine combinations. The decision parameters used in the algorithm of the method were calculated by treating 2, 535 mass spectra from the NBS database. The result of the analysis is a graphic output (isotope cluster chromatograms) and tabulated output. The applicability and the reliability of the isotope detector and the mode of using the input program parameters are discussed. The reliability of the correct recognition of isotope clusters evaluated by means of the spectra from the NBS database was 92% for chlorinated and brominated compounds but only 51%, for sulphur containing compounds.     

Determination of pKa values of quinolones from mobility and spectroscopic data obtained by capillary electrophoresis and a diode array detector

This work compares the values of dissociation constants obtained from electrophoretic mobilities of a series of quinolones at different pH values and those obtained using absorbance spectra at the maximum of the eletrophoretic peaks. The results obtained show that the two methods are complementary and constitute a valuable means of obtaining better precision. The two methods proposed can be used simultaneously without an increase in the experimental time and allow confirmation of the results obtained.     

Non-linearity in the quadrupole detector system: implications for the determination of the 13C mass distribution of an ion fragment

Some biomedical (13)C tracer applications to study glucose/lactate metabolism require the determination of up to 7 mass isotopomers of glucose, generated by the (13)C-labeling. Isotopomer ratios determined by GC-Quadrupole-MS can depend on the analyte amount being measured and may differ from expected theoretical values. A calibration is necessary to correct these effects. However, the large number of different isotopomers prevents an empirical calibration, that is based on known isotopomer mixtures. Neither insufficient mass separation in the quadrupole nor proton adducts or losses of the ionized fragment can account for the observed deviation from expected values and the dependency on the sample size. We explain the deviations with a nonlinear mapping of the isotopomer amount being analyzed to the area under the elution curve for the corresponding mass channel. The nonlinear relation allows to estimate potential errors in the determination of isotopomer ratios. It also allows to define a dynamic range as the range of signal areas, for which the systematic error in the isotopomer ratio determination is below 5% of the nominal value. It is 1 : 200 and 1 : 500 for two different fragments of glucose, measured under EI and CI and is smaller than the range imposed by the measurement precision. After correcting the nonlinearities the dynamic range improved by the factor 10 in both cases.     

Rapid and ultra-sensitive GC/MS analyses with a microchannel plate array detector Part I: Possibilities of simultaneous ion detection in narrow-bore GC/MS

Identification and detection limits for scanning and non-scanning mass spectrometers are discussed. It is theoretically deduced and experimentally confirmed that these limits are on the low pico-and femtogram levels, respectively, when using conventional secondary electron multiplier-amplifier systems. The sensitivity can be increased at least tenfold by pulse-counting techniques, instead of current amplification, provided the chemical noise is sufficiently low. The potential advantages of a detection system for simultaneous ion detection in a significant mass range, for obtaining complete mass spectra in fast GC/MS analyses, are demonstrated. A double focusing mass spectrometer was constructed, using the well-proven Mattauch-Herzog principles. By application of an “electronic photoplate”, substance identification in the low femtogram range on a millisecond time scale, so far only accessible for single ion monitoring techniques, is feasible.     

Simultaneous determination of nine nucleosides and nucleobases in different Fritillaria species by HPLC‐diode array detector

A sensitive and reliable HPLC‐diode‐array detector method was developed for the first time to simultaneously determine nine nucleosides and nucleobases including uracil, cytidine, guanine, uridine, thymine, inosine, guanosine, thymidine and adenosine in 13 different Fritillaria species. The analysis was performed on a BaseLine C18 column with a gradient of acetonitrile in water at a flow rate of 0.8 mL/min. The diode‐array detector wavelength was set at 260 nm for the UV detection of nucleosides and nucleobases. Satisfactory separation of these compounds was obtained in less than 40 min. The optimized method provided good linear relation (r² >0.9995 for all the investigated analytes), satisfactory precision (RSD <1.51%) and good recovery (from 97.64 to 101.16%). The established method was successfully applied to simultaneous determination of nine nucleosides and nucleobases in 61 batches of samples from 13 Fritillaria species collected from different habitats in China, which could be helpful to control the quality of Fritillaria bulbs.     

A high-resolution accurate mass approach to identification of graveoline metabolites using ultra-high-performance liquid chromatography combined with a photo diode array detector and quadrupole/time-of-flight tandem mass spectrometry

Graveoline is a biologically active ingredient extracted from Ruta graveolens. Current work aimed at investigating in vitro metabolism of graveoline using rat or human liver microsomes and hepatocytes. Graveoline (20 μM) was incubated with nicotinamide adenine dinucleotide phosphate–supplemented rat and human liver microsomes as well as hepatocytes. LC coupled to a photo diode array detector and quadrupole/time-of-flight tandem mass spectrometry was used to detect and identify the metabolites. The structures of the metabolites were identified by accurate mass, elemental composition, and indicative fragment ions. A total of 12 metabolites, comprising 6 phase I and 6 phase II metabolites, were obtained. The metabolic pathways included demethylenation, demethylation, hydroxylation, glucuronidation, and glutathion conjugation. The metabolite (M10) produced by opening the ring of the methylenedioxyphenyl moiety was detected as the most abundant in both liver microsomes and hepatocytes, mainly catalyzed by CYP1A2, 2C8, 2C9, 2C19, 2D6, 3A4, and 3A5. This study provides valuable information on the in vitro metabolism of graveoline, which is indispensable for further development and safety evaluation of this compound.     

Microwave-induced plasma emission spectrophotometer combined with a photodiode array monitor for capillary column gas chromatography

A microwave-induced plasma emission spectrophotometric detector (MIPD) was used as an element-specific detector for capillary column gas chromatography. The atmospheric pressure microwave helium plasma generated with an original device called a SURFATRON was used as an atomization and excitation source. Combining a photodiode array spectrophotometer with the above system made the emission spectrophotometric detector very powerful. A wide range of spectra could be instantly monitored without any mechanical device. However, the spectrum of atmospheric helium emission plasma was complicated by the presence of air around the plasma discharge. An on-line background correction scheme was developed to handle such complicated spectra.     

Characterization of microchannel plate detector response for the detection of native multiply charged high mass single ions in orthogonal-time-of-flight mass spectrometry using a Timepix detector

Time-of-flight (TOF) systems are one of the most widely used mass analyzers in native mass spectrometry (nMS) for the analysis of non-covalent multiply charged bio-macromolecular assemblies (MMAs). Typically, microchannel plates (MCPs) are employed for high mass native ion detection in TOF MS. MCPs are well known for their reduced detection efficiency when impinged by large slow moving ions. Here, a position- and time-sensitive Timepix (TPX) detector has been added to the back of a dual MCP stack to study the key factors that affect MCP performance for MMA ions generated by nMS. The footprint size of the secondary electron cloud generated by the MCP on the TPX for each individual ion event is analyzed as a measure of MCP performance at each mass-to-charge (m/z) value and resulted in a Poisson distribution. This allowed us to investigate the dependency of ion mass, ion charge, ion velocity, acceleration voltage, and MCP bias voltage on MCP response in the high mass low velocity regime. The study of measurement ranges; ion mass = 195 to 802,000 Da, ion velocity = 8.4 to 67.4 km/s, and ion charge = 1+ to 72+, extended the previously examined mass range and characterized MCP performance for multiply charged species. We derived a MCP performance equation based on two independent ion properties, ion mass and charge, from these results, which enables rapid MCP tuning for single MMA ion detection.     

Simultaneous acquisition of X-ray spectra using a multi-wire, position-sensitive gas flow detector

A multi-wire, gas-filled position-sensitive detector has been developed for the simultaneous recording of wavelength-dispersed X-ray signals that enables X-ray fluorescence spectrometry with a limited multi-element capability in the low Z element range. Details of the modular construction of the detector are given. The detector performance was characterized using Al–K radiation and a variable slit system. The detector has been applied in a laboratory spectrometer equipped with an electron source and a double multilayer mirror device as the wavelength-dispersing element. Spectra from Al and Si obtained in the simultaneous acquisition mode show good agreement with calculations performed using a ray-tracing model.