液相色谱用LED诱导荧光检测器的研究

采用共聚焦光学结构,以高强度365nm UV-LED为激发光源,设计了一种新型UV-LED诱导荧光检测器。以荧光增白剂OB为样品,对该检测器进行了性能评价,基线噪声为0.052mV,漂移为0.094mV/h,检出限(S/N=3)达3.0×10-12g/mL,线性范围达3个数量级,日内和日间保留时间、峰高和峰面积的重现性(RSD)均小于1%(n=5);以黄曲霉毒素M1为分析对象,检出限(S/N=3)为1.8×10-10g/mL。测试结果说明该荧光检测器与商品化检测器性能相当,可用于环境、食品和生物等样品的痕量分析。     

线斑激光诱导荧光微池检测器的研制及性能测试

以930荧光光度计为框架,匹配自制石英荧光微池及532 nm线状光斑激发光源,研制了线斑激光诱导荧光微池检测器(LIF–D)。以罗丹明B为样品评价该检测器的性能,连续10次进样,峰高测定结果的相对标准偏差为1.2%,检出限为5.0×10–6g/L(S/N≥3,进样体积20μL),质量检出限为1.0×10–10g,线性范围为5.0×10–6～2.0×10–2g/L(r=0.9983)。     

毛细管电泳-473 nm固体激光诱导荧光检测系统的建立

以发射波长473nm的半导体激光泵浦固体激光器(LD DPSSL)为激发光源,研制了一种小型模块化激光诱导荧光检测器。以异硫氰酸荧光素(FITC)为荧光探针,毛细管电泳柱上检测(0.05mmi.d)评价了该体系,得到了5×10-12mol L的浓度检出限。利用该系统考察了氨基酸、实际样品中B族维生素的检测。     

芯片毛细管电泳荧光检测器灵敏度的研究

本文采用倒置荧光显微镜,以汞灯为激发光源,自行设计组装了芯片毛细管电泳荧光检测系统。以荧光素异硫氰酸酯(FITC)为检测对象,对双通道门控光子计数器、CH151型光子计数探测器、电荷耦合器件(CCD)三种荧光检测器的灵敏度进行了比较研究。根据芯片毛细管电泳图谱分析,FITC在双通道门控光子计数器、CH151型光子计数探测器、CCD三种检测器中的检出限(S/N=3)分别为7.0×10-10mol/L,1.2×10-9mol/L,3.2×10-8mol/L。进一步采用CH151型光子计数探测器和CCD两种较常用检测器,对FITC和荧光素、曙红和荧光素两组荧光试剂的分离及检测进行了研究。结果表明,使用CH151型光子计数探测器作为检测器,灵敏度高,基线稳定,信噪比高。     

汞灯光源芯片毛细管电泳荧光电荷耦合器件检测系统

以宽谱带高压汞灯为光源的倒置荧光显微镜,配备电荷耦合器件(CCD)及微流控芯片,自组装芯片毛细管电泳荧光电荷耦合器件检测系统。选择不同激发波长(340~540 nm)荧光试剂,进行荧光检测,荧光素的检出限(S/N=3)为7.3×10-9mol/L,荧光素异硫氰酸酯(FITC)的检出限(S/N=3)为1.7×10-8mol/L,显示了该系统对荧光试剂选择范围宽、灵敏度高的特点。用该系统成功分离了FITC与荧光素、曙红与荧光素两种混合荧光试剂。实验表明,组装的芯片毛细管电泳CCD荧光检测系统是成功的。     

实用型简易激光诱导荧光检测器的研制及性能测试

基于正交型结构,研制了一种简易实用的高效液相色谱激光诱导荧光检测器。以930荧光光度计为骨架,用岛津RF-535荧光检测池,配以自制可调稳压电源,分别以波长532am和405nm的自制激光器为激发光源,以罗丹明B和荧光素为荧光试剂评价体系的性能。罗丹明B的检出限为2．0×10^-8mol／L（S／N〉10）,荧光素的检出限为3．0×10^-10mol／L（S／N〉10）。测试结果表明该检测器达到了设计要求,具有足够的实用灵敏度和较宽的线性范围。     

花旗松素与牛血清白蛋白相互作用的光谱和电化学

采用紫外光谱法、荧光光谱法和循环伏安法,研究了牛血清白蛋白(BSA)与花旗松素（taxifolin）的相互作用。 用荧光法和循环伏安法测得花旗松素与BSA的结合常数K分别为1.3×106和1.6×106 L/mol,结合位点数均接近1.3。花旗松素对牛血清白蛋白是静态猝灭。BSA荧光强度的降低与花旗松素浓度在一定范围内呈线性关系,其线性范围为6.00×10-7~2.00×10-5 mol/L,检出限为2.00×10-7 mol/L。花旗松素氧化峰电流的下降与BSA浓度在一定范围内呈线性关系,其线性范围为7.00×10-7~1.00×10-4 mol/L,检出限为3.00×10-7 mol/L。用于合成样品中花旗松素和BSA的测定,结果满意。     

激光诱导荧光检测微流控芯片生化分析仪的研制

研制出一种集激光诱导荧光检测、微流控芯片电泳及控制系统于一体的生化分析仪。分析仪内采用可重复使用的玻璃基质微流控芯片,利用销式固定技术实现芯片的精确定位,定位精度达到±2μm。以四触点高电压系统控制芯片上的进样和电泳分离操作。激光诱导荧光检测系统采用正交光路模式,对Cy5染料的检出限达到1.0×10-10mol/L(S/N=3)。以羟乙基纤维素为筛分介质,初步进行了ΦΧ174-HaeШdigest DNAmarker限制性片段的毛细管电泳分离。     

修饰铂电极上Bi(Ш)的示波双电位滴定法

制备了Bi(Ⅲ)修饰铂电极,用循环伏安法表征了Bi(Ⅲ)在电极上的吸附特性,探讨了电极的响应机理。 通过优化实验条件,建立了一种测定Bi(Ⅲ)的示波双电位滴定法。 在0.1 mol/L的硝酸溶液中(pH=1.0),用制备的修饰铂电极作为双指示电极,以EDTA标准溶液滴定Bi(Ⅲ),利用示波器屏幕上荧光点的显著最大位移指示滴定终点。 Bi(Ⅲ)在1.19×10-4～1.44×10-2 mol/L时,回收率为99.8%～100.1%,检出限(S/N=3)为1.0×10-4 mol/L。 该修饰电极具有良好的稳定性和重现性,在含有1.0×10-2 mol/L Bi(Ⅲ)的溶液中,连续7次测定,所得终点电位值均在100 mV左右,其相对标准偏差(RSD)为0.04%。 应用该方法测定含铋样品,RSD值(n=7)小于0.25%,回收率为99.5%～100.5%,测定结果与指示剂法测定值相符。     

锆-茜素红络合物在多壁碳纳米管修饰碳糊电极上的阳极吸附伏安法研究

制备了多壁碳纳米管修饰碳糊电极并研究了锆-茜素红络合物在该电极上的阳极吸附伏安行为,采用二阶导数线性扫描伏安法进行分析,实验结果表明,在0.128 mol/L氨基乙酸-0.048 mol/L邻苯二甲酸氢钾缓冲液(pH 4.0)中,在200 mV富集60 s,在200~1200 mV范围内以200 mV/s的速率线性扫描,络合物吸附在该修饰电极表面,于832 mV(vs.SCE)处产生一个灵敏的氧化峰,为络合物中配体茜素红的氧化所产生。络合物的峰电流与锆的浓度在1.0×10-11~2.0×10-7mol/L范围内呈良好的线性关系;检出限(S/N=3)为6.0×10-12mol/L(富集时间180 s)。方法用于岩矿样品中痕量锆的测定,结果满意。     

Determination of clozapine by capillary zone electrophoresis following end-column amperometric detection with simplified capillary/electrode alignment

Capillary zone electrophoresis was employed for the determination of clozapine using an end-column amperometric detection at a carbon fiber array microdisk electrode with simplified capillary/electrode alignment. The optimum conditions of separation and detection are: Britton-Robinson buffer, pH 2.0 (1.3 x 10(-2) mol/L total concentration of acids, 3.2 x 10(-3) mol/L NaOH), 15 kV for separation voltage, 5 kV and 10 s for injection voltage and injection time, respectively. The limit of detection is 4.2 x 10(-7) mol/L or 1.2 fmole (signal to noise, S/N = 2). The relative standard deviation is 1.4% for the migration time and 2.5% for the electrophoretic peak current. The method was applied to the determination of clozapine in human blood. The recovery of the method is between 94-104%.     

1-(3-硝基苯基)-3-[4-(苯基偶氮)苯基]-三氮烯修饰碳糊电极测定痕量锡

制备了三氮烯修饰碳糊电极(m-NPPAPT/CPE),并研究了Sn(Ⅱ)在该电极上的吸附伏安行为,建立了一种测定痕量锡(Ⅱ)的新方法。采用二阶导数线性扫描溶出伏安法进行分析。结果表明:在1mL 0.5mol/L HCl溶液中,于-1200mV处搅拌富集一定时间,在-1200～-200mV范围内以150mV/s的扫描速度线性扫描,Sn(Ⅱ)吸附在修饰电极表面,于约-476mV(vs SCE)处产生一个灵敏的阳极溶出峰,峰电流比未修饰电极增大约11倍。其峰电流与Sn(Ⅱ)浓度在4.0×10-10～1.0×10-8 mol/L和1.0×10-8～4.0×10-6 mol/L范围内分两段呈良好线性关系,其线性回归方程分别为ip(μA)=1.646C(μmol/L)+2.9566和ip(μA)=52.804C(μmol/L)-0.6402,相关系数分别为0.9973和0.9967;检出限(S/N=3)为2.7×10-10 mol/L(富集时间120s)。本方法操作简便、灵敏度高,应用于罐头食品中锡含量的测定,结果满意。     

Simultaneous square-wave voltammetric determination of aspartame and cyclamate using a boron-doped diamond electrode

A simple and highly selective electrochemical method was developed for the simultaneous determination of aspartame and cyclamate in dietary products at a boron-doped diamond (BDD) electrode. In square-wave voltammetric (SWV) measurements, the BDD electrode was able to separate the oxidation peak potentials of aspartame and cyclamate present in binary mixtures by about 400 mV. The detection limit for aspartame in the presence of 3.0x10(-4) mol L(-1) cyclamate was 4.7x10(-7) mol L(-1), and the detection limit for cyclamate in the presence of 1.0x10(-4) mol L(-1) aspartame was 4.2x10(-6) mol L(-1). When simultaneously changing the concentration of both aspartame and cyclamate in a 0.5 mol L(-1) sulfuric acid solution, the corresponding detection limits were 3.5x10(-7) and 4.5x10(-6) mol L(-1), respectively. The relative standard deviation (R.S.D.) obtained was 1.3% for the 1.0x10(-4) mol L(-1) aspartame solution (n=5) and 1.1% for the 3.0x10(-3) mol L(-1) cyclamate solution. The proposed method was successfully applied in the determination of aspartame in several dietary products with results similar to those obtained using an HPLC method at 95% confidence level.     

Direct electrochemical determination of pyruvate in human sweat by capillary zone electrophoresis.

Capillary zone electrophoresis was employed for the determination of pyruvate in human sweat using electrochemical detection with a carbon fiber microdisk bundle electrode at a constant potential of 1.60 V vs. saturated calomel electrode. The optimum separation conditions are 3.6 x 10(-3) mol/L Na2HPO4-1.4 x 10(-3) mol/L NaH2PO4 (pH 7.2) for the buffer solution, and 18 kV for the separation voltage. The limits of detection of pyruvate are 8.0 x 10(-6) mol/L or 24 fmol (S/N = 3) for the injection voltage of 6 kV and the injection time of 10 s. The relative standard deviation is 2.0% for the migration time and 5.7% for the electrophoretic peak current. The method was applied to determining pyruvate in human sweat.     

Characterization of procaine metabolism as probe for the butyrylcholinesterase enzyme investigation by simultaneous determination of procaine and its metabolite using capillary electrophoresis with electrochemiluminescence detection

Capillary electrophoresis with electrochemiluminescene detection was used to characterize procaine hydrolysis as a probe for butyrylcholinesterase by in vitro procaine metabolism in plasma with butyrylcholinesterase acting as bioscavenger. Procaine and its metabolite N,N-diethylethanolamine were separated at 16 kV and then detected at 1.25 V in the presence of 5.0 mM Ru(bpy)(3)2+, with the detection limits of 2.4x10(-7) and 2.0x10(-8) mol/L (S/N=3), respectively. The Michaelis constant Km value was 1.73x10(-4) mol/L and the maximum velocity Vmax was 1.62x10(-6) mol/L/min. Acetylcholine bromide and choline chloride presented inhibition effects on the enzymatic cleavage of procaine, with the 50% inhibition concentration (IC50) of 6.24x10(-3) and 2.94x10(-4) mol/L.     

New technique for capillary electrophoresis directly coupled with end-column electrochemiluminescence detection

A new end-column electrochemiluminescence (ECL) detection technique coupling to capillary electrophoresis (CE) is characterized. A 300 microm diameter Pt working electrode was used to directly couple with a 75 microm inner diameter separation capillary without an electric field decoupler. The hydrodynamic cyclic voltammogram (CV) of Ru(bpy) 3 2+ showed that electrophoretic current did not affect the ECL reaction. The presence of high-voltage (HV) field only resulted in the shift of the ECL detection potential. The distance of capillary to electrode was an important parameter for optimizing detection performance as it determined the characteristics of mass transport toward the electrode and the actual concentration of Ru(bpy) 3 2+ in the detection region. The optimum distance of capillary to electrode was decided by the inner diameter of the capillary, too. For a 75 microm capillary, the working electrode should be placed away from the capillary outlet at a distance within the range of 220-260 microm. The effects of pH value of ECL solution and molecular structure of analytes on peak height and theoretical plate numbers were discussed. Using the 75 microm capillary, under the optimum conditions, the method provided a linear range for tripropylamine (TPA) between 1 x 10(-10) and 1 x 10(-5) mol/L with correlation coefficient of 0.998. The detection limit (signal-to-noise ratio S/N = 3) was 5.0 x 10(-11) mol/L. The relative standard deviation in peak height for eight consecutive injections was 5.6%. By this new technique lidocaine spiked in a urine sample was determined. The method exhibited the linear range for lidocaine from 5.0 x 10(-8) to 1.0 x 10(-5) mol/L with correlation efficient of 0.998. The limit of detection (S/N = 3) was 2.0 x 10(-8) mol/L.     

Sensitive determination of norepinephrine, synephrine, and isoproterenol by capillary electrophoresis with indirect electrochemiluminescence detection

A new and sensitive method for the determination of norepinephrine (NE), synephrine, and isoproterenol was developed by CE separation and indirect electrochemiluminescence detection (ECL) based on their quenching effects on the tris(2,2'-bipyridyl)-ruthenium(II)/tripropylamine (TPA) system. The conditions for CE separation and ECL detection were investigated in detail. Under the optimum conditions, the three analytes were well separated within 9 min. The LODs (S/N = 3) in standard solution are 2.6 x 10(-8) mol/L for NE, 6.6 x 10(-9) mol/L for synephrine and 8.4 x 10(-8) mol/L for isoproterenol, respectively. The precisions of intraday and interday are less than 4.4 and 6.1%, respectively. The LOQs (S/N = 10) in real human urine samples are 2.6 x 10(-7) mol/L for NE, 8.8 x 10(-8 ) mol/L for synephrine, and 8.8 x 10(-7) mol/L for isoproterenol, respectively. The applicability of the proposed method was illustrated in the determination of 20 human urine samples from diabetic patients and healthy persons. The results obtained indicated that the level of NE in patients (mean value 0.41 micromol/L) was higher than that in healthy persons (mean value 0.24 micromol/L).     

Determination of levofloxacin and norfloxacin by capillary electrophoresis with electrochemiluminescence detection and applications in human urine

A novel method for the determination of norfloxacin (NOR) and levofloxacin (LVX) was developed by CE separation and electrochemiluminesence detection (ECL). The methods for capillary conditioning and the effect of solvent type were studied. Parameters affecting the CE and ECL were also investigated. Under the optimum conditions, the two analytes were well separated within 9 min. The LODs (S/N = 3) in standard solution are 4.8 x 10(-7) mol/L for NOR and 6.4 x 10(-7) mol/L for LVX, respectively. The precisions of intraday and interday are less than 4.2 and 8.1%, respectively. The LOQs (S/N = 10) in real human urine samples are 1.2 x 10(-6) mol/L for NOR and 1.4 x 10(-6) mol/L for LVX, respectively. The applicability of the proposed method was illustrated in the determination of NOR and LVX in human urine samples and the monitoring of pharmacokinetics for NOR. The recoveries of NOR and LVX at different levels in human urine samples were between 84.3 and 92.3%.     

Evaluation of a carbon paste electrode modified with organofunctionalised SBA-15 nanostructured silica in the simultaneous determination of divalent lead, copper and mercury ions

The performance of a carbon paste electrode (CPE) modified with SBA-15 nanostructured silica organofunctionalised with 2-benzothiazolethiol in the simultaneous determination of Pb(II), Cu(II) and Hg(II) ions in natural water and sugar cane spirit (cacha?a) is described. Pb(II), Cu(II) and Hg(II) were pre-concentrated on the surface of the modified electrode by complexing with 2-benzothiazolethiol and reduced at a negative potential (-0.80 V). Then the reduced products were oxidised by DPASV procedure. The fact that three stripping peaks appeared on the voltammograms at the potentials of -0.48 V (Pb2+), -0.03 V (Cu2+) and +0.36 V (Hg2+) in relation to the SCE, demonstrates the possibility of simultaneous determination of Pb2+, Cu2+ and Hg2+. The best results were obtained under the following optimised conditions: 100 mV pulse amplitude, 3 min accumulation time, 25 mV s(-1) scan rate in phosphate solution pH 3.0. Using such parameters, calibration graphs were linear in the concentration ranges of 3.00-70.0 x 10(-7) mol L(-1) (Pb2+), 8.00-100.0 x 10(-7) mol L(-1) (Cu2+) and 2.00-10.0 x 10(-6) mol L(-1) (Hg2+). Detection limits of 4.0 x 10(-8) mol L(-1) (Pb2+), 2.0 x 10(-7) mol L(-1) (Cu2+) and 4.0 x 10(-7) mol L(-1) (Hg2+) were obtained at the signal noise ratio (SNR) of 3. The results indicate that this electrode is sensitive and effective for simultaneous determination of Pb2+, Cu2+ and Hg2+ in the analysed samples.