固相微萃取-气相色谱法测定白洋淀水样中的邻苯二甲酸酯类化合物

建立了固相微萃取(SPME)-气相色谱法(GC)分析环境水样中痕量邻苯二甲酸酯类化合物(PAEs)的方法。选用100 μm聚二甲基硅烷(PDMS)萃取纤维,在磁力搅拌条件下,对水样中的PAEs萃取富集60 min,然后直接注入GC进样口,在250 ℃温度下解吸4 min后进行分析测定,13种PAEs能得到充分提取和分离。方法的重现性(以相对标准偏差(RSD)计为0.2%～9.7%,检出限为0.02～0.83 μg/L。将本方法应用于白洋淀水样中PAEs的分析检测发现,样品中邻苯二甲酸二异丁酯(DIBP)、邻苯二甲酸二丁酯(DBP)、邻苯二甲酸二(2-乙基己基)酯(DEHP)检出率相对较高。对水样进行两个浓度水平(2.5 μg/L和5.0 μg/L)的加标试验,加标回收率为75.3%～111.0%,RSD为2.1%～8.0%(n=3),能够满足环境水样中痕量PAEs的测定要求。     

固相微萃取-高效液相联用分析环境水样中的痕量■

 应用固相微萃取与高效液相联用技术 (SPME HPLC)分析了环境水样中的痕量 艹屈 。对SPME的条件如萃取时间、萃取温度、离子强度、解吸方式、解吸溶剂、解吸时间和HPLC条件进行了优化 ,建立了SPME HPLC分析环境水样中痕量 艹屈 的方法 ,并将其用于分析自来水、雨水、矿泉水和江水等实际水样。方法的线性范围为 0 0 13μg/L～ 3 0 μg/L ,检出限为 2 7ng/L ,相对标准偏差 (RSD ,n =6 )为 5 6 % ,回收率为 10 3 2 %～ 119 3%。该方法适合于环境水样中痕量 艹屈 的分析 ,体现了SPME在样品前处理中快速、灵敏、简单、无溶剂的特点。     

微滴液相微萃取技术用于气相色谱-质谱法测定食品中的酞酸酯

将一种新型、简单、快速、环境友好的萃取方法微滴液相微萃取(SDME)与气相色谱-质谱法结合用于快速分析食品中的几种酞酸酯(PAEs)。考察了萃取溶剂的种类及用量、微液滴在样品溶液中的深度、萃取时间及搅拌子的搅拌速度对微滴液相微萃取的影响。优化的萃取条件为:萃取溶剂为2.0 μL甲苯,微液滴在样品溶液中的深度为0.75 cm,搅拌速度为1000 r/min,萃取时间为20 min。该方法的线性范围为0.1～4000 μg/L,检测限为25 ng/L～0.8 mg/L,加标回收率为87.1%～114.4%,相对标准偏差为4.9%～11.6%。微滴液相微萃取所需的有机溶剂量很小,是一种快速、简单、安全、有效的水溶性样品的前处理方法。     

固相微萃取-高效液相色谱联用测定水样中的痕量苯并(k)荧蒽

研究了固相微萃取(SPME)-高效液相色谱(HPLC)联用测定水样中痕量苯并(k)荧蒽的的分析方法。对SPME的条件如萃取时间、萃取温度、离子强度、解吸方式、解吸溶剂、解吸时间和HPLC条件进行了优化，建立了SPME-HPLC联用分析水样中痕量苯并(k)荧蒽的方法，并用于自来水、雨水和纯净水等实际水样的分析。SPME优化的条件为室温、搅拌速度1100r／min、萃取时间30min、甲醇解吸溶剂、解吸时间2min。HPLC的条件为C18反相色谱柱、甲醇流动相、流速1mL/min、紫外检测器、波长244nm，以峰高为测量信号。方法的线性范围为0～8．00μg／L，检出限为0．014μg／L，相对标准偏差(n=6)为6．7％，回收率为82．0％～104．2％。该方法适合于水样中痕量苯并(k)荧蒽的分析。     

搅拌棒萃取-热解吸气相色谱法测定水中倍半芥子气

建立了一种以SBSE萃取与热解吸-气相色谱-火焰光度法联用技术为基础的测定水中倍半芥子气的方法。对比了SBSE和固相微萃取(SPME)对水中的倍半芥子气的萃取回收率,实验结果表明,SBSE对倍半芥子气的萃取率在22.47%～22.60%之间,SPME对倍半芥子气的萃取率为0.4%。研究了萃取时间、解吸附时间、样品溶液pH值、萃取温度对萃取回收率的影响,选择萃取时间为20min、一级解吸时间为10min、二级解吸时间为4min、样品溶液pH值为7.0、萃取温度为25℃。检测倍半芥子气的线性范围为0.462～23.1μg/L,最低检出限为0.0924μg/L(S/N=3)。该方法已成功应用于河水的检测。     

微波辅助-微固相在线萃取/气相色谱质谱联用法对污泥中19种多氯联苯的测定

建立了微波辅助-微固相在线萃取/气相色谱-质谱联用(GC-MS)测定污泥中19种多氯联苯(PCBs)含量的分析方法。对微波辅助-微固相在线萃取条件进行优化,得出最优萃取条件为:萃取温度60℃,萃取时间25 min,解吸溶剂为乙酸乙酯,解吸剂用量150μL,解吸时间25 min。在优化条件下,方法的检出限为0.2~2.5 ng/g,相对标准偏差(RSD)小于14%,回收率为81.4%~102.1%。与传统的微波萃取、微固相萃取、超声萃取等方法相比,该方法集萃取、净化和浓缩于一体,极大地缩短了分析时间,适合于复杂环境样品体系中痕量PCBs的分析检测。     

固相微萃取-气相色谱-质谱联用分析环境水样中痕量有机磷农药

研究了固相微萃取(SPME) 气相色谱 质谱联用(GC MS)同时测定环境水样中二嗪农、甲基对硫磷、对硫磷和水胺硫磷4种有机磷农药(OPPs)的分析方法。选择聚丙烯酸酯(PA)萃取纤维,对SPME的条件如萃取时间、萃取溶液的pH值和离子强度、解吸温度、解吸时间和GC MS的条件进行了优化。对二嗪农和水胺硫磷方法线性范围为0.001～10μg L,对甲基对硫磷和对硫磷方法线性范围为0.001～100μg L。二嗪农、甲基对硫磷、对硫磷、水胺硫磷的检出限分别为0.015,0.020,0.013和0.039μg L。分析加标自来水、矿泉水和湖水样品,回收率在89.0%～102%之间,RSD在2.1%～14.1%之间。适合于环境水样中痕量OPPs的快速分析。     

固相膜萃取-超声解吸-气相色谱-质谱法分析水中酞酸酯类化合物

酞酸酯(PAEs)是一种常用的增塑剂,由于其广泛应用已经对环境造成了污染.本研究建立了固相膜萃取-超声解吸-气相色谱-质谱分析水中酞酸酯类化合物的方法.对萃取条件、解吸条件进行了优化,确定了最佳的实验条件.在水浴温度40℃,超声功率50%的条件下超声7 min,测定水中PAEs的检出限(S/N>3)在0.05 ~0.26 μg/L之间;对不同基质空白样品进行加标回收实验,回收率在76.2%~112.3%之间,相对标准偏差小于10%.     

液相微萃取-气相色谱法测定水样中微量酚类污染物

提出了一种静态液相微萃取与气相色谱联用技术测定水样中微量酚类污染物的方法.以苯酚为代表,考察了萃取溶剂种类和用量、搅拌速度、萃取时间、pH值及离子强度对酚类化合物的静态液相微萃取效率的影响.优化的萃取条件为:3.0μL甲苯为萃取剂(对硝基甲苯为内标),搅拌速度150 r·min-1,萃取时间20 min,pH为2.2,离子强度为200 g·L-1氯化钠溶液.在优化的萃取和色谱条件下,苯酚和氯酚的线性范围分别为0.02～20.00 mg·L-1和0.02～10.00 mg·L-1,检出限(3S/N)为0.01 mg·L-1.用此方法分析了一种湖水样品中的酚类污染物,并以此样品为基体进行回收及精密度试验,测得平均回收率为93.7%,相对标准偏差(n=7)为6.3%.     

中空纤维膜液相微萃取/高效液相色谱法测定水样中4种头孢菌素的含量

基于中空纤维膜液相微萃取/高效液相色谱(HF-LPME/HPLC),建立了水样中痕量头孢唑林(CZO)、头孢呋辛(CXM)、头孢他定(CAZ)和头孢西丁(FOX) 4种头孢菌素残留的检测方法。优化得到最佳萃取条件:萃取溶剂为1-辛基-3-甲基咪唑六氟磷酸盐([Omin]PF_6),辅助萃取溶剂为10%三正辛基氧膦(TOPO),样品溶液pH值为2.5,萃取时间为20 min,萃取温度为30℃,搅拌速率为600 r/min。以Agilent Poroshell 120 EC-C_(18)(100 mm×4.6 mm,2.7μm)为色谱柱,以0.05 mol/L醋酸钠缓冲液(pH 4.0)-乙腈(9∶1,体积比)为流动相,4种头孢菌素可在7 min内完全分离。结果表明4种头孢菌素的线性关系良好,富集倍数为45～78倍,检出限为0.2～0.7 ng/mL,回收率为83.2%～102%,相对标准偏差为2.0%～9.8%。该方法简单高效,检测成本低,溶剂用量少,绿色环保,灵敏度高,对水样中痕量头孢菌素残留的富集能力强。     

分子印迹聚合物为涂层的吸附萃取搅拌棒在环境水样双酚A含量测定中的应用

以双酚A(BPA)为单体,利用整体材料“原位”聚合技术制备以分子印迹聚合物为涂层的吸附萃取搅拌棒(MIP-SBSE),然后与高效液相色谱(HPLC)-二极管阵列检测器联用,探讨其对环境水样BPA的选择萃取性能。优化萃取过程中吸附和解吸时间、解吸液种类以及基底pH值和离子强度对目标化合物的选择吸附性能。在最佳条件下,MIP-SBSE可对模板分子进行有效的选择吸附,线性范围为1.0～200 μg/L,检出限(S/N=3)和定量限(S/N=10)分别为0.28μg/L和0.94 μg/L。在实际水样分析中,具有良好的加标回收率,其值为96.0%～108.7%。研究结果表明,所建立的方法具有简便、灵敏和环境友好等特点。     

基于低共熔溶剂的整体式萃取头的制备及其对湖水中3种多环芳烃的固相微萃取（英文）

采用氯化胆碱-乙二醇低共熔溶剂(DES)作致孔剂,制备了聚(甲基丙烯酸丁酯-乙二醇二甲基丙烯酸酯)[poly(BMA-EDMA)]固相微萃取头,并与超高效液相色谱法(UPLC)结合测定了湖水中的3种多环芳烃(PAHs)。实验与不使用DES致孔剂的固相微萃取头和商品化聚二甲硅氧烷(PDMS)萃取头进行比较,含DES的poly(BMA-EDMA)固相微萃取头的富集效果最好。系统考察了萃取条件(萃取时间、萃取溶剂、解吸时间、解吸溶剂及离子强度)对水样中多环芳烃萃取效率的影响。在最优的实验条件下,3种多环芳烃类化合物(萘、联苯、菲)的线性范围为0.1~6.0 mg/L(r≥0.990 3),检出限为2.1~4.9μg/L,回收率为86.4%~111.3%,相对标准偏差(RSD,n=6)为11.2%~15.1%。该法操作简便,稳定性好,成本低,适用于实际环境水样中多环芳烃类化合物的测定。     

Ion-pair sorptive extraction of perfluorinated compounds from water with low-cost polymeric materials: Polyethersulfone vs polydimethylsiloxane

A method for the determination of seven perfluorinated carboxylic acids and perfluorooctane sulphonate (PFOS) in aqueous samples using low-cost polymeric sorptive extraction as sample preparation technique, followed by liquid chromatography–tandem mass spectrometry (LC–MS/MS) determination has been developed and validated. Simplicity of the analytical procedure, low volume of solvent and sample required, low global price and a good selectivity providing cleaner extracts are the main advantages of this extraction technique. Polydimethylsiloxane (PDMS) and polyethersulfone (PES) materials were evaluated and compared to achieve the best extraction efficiencies. Hence, different variables have been optimized, viz.: sample pH, concentration of an ion-pairing agent (tetrabutylammonium), ionic strength, sample volume, extraction time, desorption solvent volume, desorption time and the need for auxiliary desorption techniques (sonication). Overall, PES leaded to a better sensitivity than PDMS, particularly for the most polar compounds, reaching detection limits (LODs) in the 0.2–20 ng L⁻¹ range. The precision of the method, expressed as relative standard deviation (RSD), was lower than 16%. Finally, the PES material was employed for the analysis of sea, sewage and fresh water samples. Perfluoroheptanoic acid (PFHpA), perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA) and perfluorodecanoic acid (PFDA) were detected in all the analyzed influent samples reaching levels of up to 401 ng L⁻¹. In surface water, perfluorohexanoic acid (PFHxA) exhibited the highest concentrations, up to 137 ng L⁻¹.     

磁固相萃取-液相色谱法测定环境水样中有机紫外防晒剂

采用自制的聚离子液体功能化磁性材料有效富集有机紫外防晒剂，并与高效液相色谱-二极管阵列检测器（HPLC-DAD）联用，建立了环境水样中痕量有机紫外防晒剂的检测方法。研究系统考察了解吸溶剂、吸附和解吸时间、样品pH值、离子强度等因素对萃取性能的影响。在最佳萃取条件下，水杨酸辛酯的线性范围为0.5~200.0 μg/L，其他有机紫外防晒剂的线性范围为0.2~200.0 μg/L；6种目标物的检出限（LOD，S/N=3）和定量限（LOQ，S/N=10）分别为0.009~0.13 μg/L和0.031~0.43 μg/L。所建方法成功用于实际环境水样中有机紫外防晒剂的测定，不同加标水平下目标物的加标回收率为71.4%~120%，相对标准偏差均低于10%。研究表明，所建方法具有操作简便、萃取速度快、灵敏度高和环境友好等特点，可用于环境水样中有机紫外防晒剂的检测。     

MIL-53(Fe)@聚多巴胺@Fe_3O_4磁性复合材料的制备及其用于环境水样中磺酰脲类除草剂的磁固相萃取

制备了MIL-53(Fe)和聚多巴胺(PDA)修饰的磁性Fe_3O_4复合材料MIL-53(Fe)@PDA@Fe_3O_4,并将其作为吸附剂用于磁固相萃取-高效液相色谱法(MSPE-HPLC)检测环境水样中4种磺酰脲类除草剂(甲嘧磺隆、苄嘧磺隆、吡嘧磺隆和氯嘧磺隆)。实验优化了高效液相色谱条件(乙腈和含0.01%(体积分数)三氟乙酸的水溶液为流动相进行梯度洗脱,检测波长为233 nm)及磁固相萃取条件(洗脱剂为5 mL丙酮,萃取时间为4.5 min,吸附剂用量为60 mg,NaCl加入量为0.5 g,溶液pH值为3),在最佳条件下进行方法学考察,4种磺酰脲类除草剂均得到良好的线性关系,相关系数(r)≥0.998 0。方法的检出限(LOD,S/N=3)为0.28~0.77μg/L。将建立的方法用于3种环境水样中4种磺酰脲类除草剂的检测,其加标回收率为78.8%~109.7%。结果表明,制备的功能化复合材料结合了MIL-53(Fe)和Fe_3O_4的优点,可以简便快速地萃取分离环境水样中磺酰脲类除草剂。     

新型磁性分子印迹聚合物的制备及其在氟喹诺酮类抗生素检测中的应用

建立了磁性分子印迹聚合物固相萃取与高效液相色谱联用同时检测环境水中4种氟喹诺酮类抗生素的研究方法。分别利用扫描电子显微镜、透射电子显微镜、X-射线衍射、傅里叶红外光谱、振动样品磁强计对合成的磁性分子印迹聚合物进行表征,对影响吸附实验的参数（包括吸附剂用量、吸附和解析时间、洗脱液种类、样品pH值）进行了考察和优化。在最佳的实验条件下,4种氟喹诺酮类抗生素的方法检出限为4.1~21.3 μg/L,方法定量限为13.7~71.0 μg/L,样品加标回收率为70.6%~103.6%。该方法快速、灵敏,能够满足环境水样中氟喹诺酮类抗生素的残留检测要求。     

Development and validation of stir bar sorptive extraction of polar phenols in water followed by HPLC separation in poly(vinylpyrrolididone‐divinylbenzene) monolith

An effective and simple method for polar phenols in water matrix was developed by using stir bar sorptive extraction (SBSE) based on a hydrophilic poly(vinylpyrrolididone‐divinylbenzene) (VPDB) monolithic material and HPLC analysis. To achieve optimum extraction performance for phenols, several parameters, including extraction and desorption time, desorption solvent, pH value, and ionic strength of sample matrix, were investigated. Under the optimized experimental conditions, eight phenols were directly enriched from water samples and analyzed by HPLC‐DAD. The detection limits (S/N = 3) and quantification limits (S/N = 10) of the proposed method for the target compounds were achieved within the range of 0.72–1.37 and 2.40–4.27 ng/mL from spiked water, respectively. Recoveries of eight phenolic compounds were found in the range of 55.2–95.9%. The calibration curves showed the linearity ranging from 5 to 150 ng/mL with linear regression coefficient R² values above 0.98. Method repeatability presented as intra‐ and interday precisions were also found with the RSDs less than 4.10 and 7.61%, respectively. The distribution coefficients between VPDB and water (K_VPDB/W) for phenolic compounds were also calculated and compared with K_O/W. Finally, the proposed method was successfully applied to the determination of the target compounds in tap water, sea water and wastewater samples.     

Development of a method for the determination of UV filters in water samples using stir bar sorptive extraction and thermal desorption-gas chromatography-mass spectrometry

Stir bar sorptive extraction (SBSE) in combination with thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS) was applied for the determination of 9 UV filters in water samples. The stir bar coated with polydimethylsiloxane (PDMS) was added to 20 mL of water sample at pH 2 (10% MeOH) and stirred at 1000 rpm for 180 min. Then, the stir bar was subjected to TD-GC-MS. The desorption conditions (desorption temperature and desorption time) and SBSE parameters (ionic strength, pH, presence of organic solvent and time) were optimised using a full factorial design and a Box-Behnken design, respectively. The method shows good linearity (correlation coefficients >0.994) and reproducibility (RSD<16%). The extraction efficiencies were above 63% for all the compounds. Detection limits were between 0.2 and 63 ng/L. The developed method offers the ability to detect several UV filters at ultra-low concentration levels with only 20 mL of sample volume. The effectiveness of the method was tested by analysing real samples such as lake water, river water and treated wastewater. The application of the method allowed reporting the levels of UV filters in environmental water samples.     

Simple and sensitive monitoring of sulfonamide veterinary residues in milk by stir bar sorptive extraction based on monolithic material and high performance liquid chromatography analysis

A simple, rapid, and sensitive method for the quantitative monitoring of five sulfonamide antibacterial residues (SAs) in milk was developed by stir bar sorptive extraction (SBSE) coupling to high performance liquid chromatography with diode array detection. The analytes were concentrated by SBSE based on poly (vinylimidazole–divinylbenzene) monolithic material as coating. The extraction procedure was very simple, milk was diluted with water then directly sorptive extraction without elimination of fats and protein in samples was required. To achieve optimum extraction performance for SAs, several parameters, including extraction and desorption time, desorption solvent, ionic strength and pH value of sample matrix were investigated. Under the optimized experimental conditions, low detection limits (S/N = 3) quantification limits (S/N = 10) of the proposed method for the target compounds were achieved within the range of 1.30–7.90 ng/mL and 4.29–26.3 ng/mL from spiked milk, respectively. Good linearities were obtained for SAs with the correlation coefficients (R²) above 0.996. Finally, the proposed method was successfully applied to the determination of SAs compounds in different milk samples and satisfied recoveries of spiked target compounds in real samples were obtained.     

共价有机框架材料磁固相萃取-高效液相色谱法分析环境水体中对羟基苯甲酸酯

建立了一种基于共价有机框架材料的磁固相萃取-高效液相色谱方法,用于环境水样中对羟基苯甲酸酯的快速灵敏分析。首先以Fe₃O₄纳米粒子为磁核,通过1,3,5-苯三甲醛(Tb)和联苯胺(Bd)在室温下的席夫碱反应合成了磁性共价有机框架材料——Fe₃O₄@TbBd,通过扫描电镜、热重分析、X射线衍射和振动样品磁强计等表征手段证明了该磁性共价有机框架材料具有良好的热稳定性和化学稳定性,且磁响应强度较大,是用于磁固相萃取的理想材料。随后系统研究了影响萃取效率的因素,包括吸附剂用量、萃取时间、pH、解吸溶剂、解吸时间和解吸次数,建立了基于Fe₃O₄@TbBd的磁固相萃取-高效液相色谱测定环境水样中4种对羟基苯甲酸酯的方法。方法的线性范围良好,4种目标物的检出限和定量限范围分别为0.2~0.4 μg/L和0.7~1.4 μg/L,加标回收率为86.1%~110.8%,日内和日间精密度的相对标准偏差(RSD)分别低于5.5%和4.9%。最后将该方法应用于东湖水、长江水和生活废水中对羟基苯甲酸酯的测定,不同加标水平下对羟基苯甲酸酯的回收率在80.7%~117.5%之间,RSD在0.2%~8.8%之间。该方法操作简单,萃取时间短,灵敏度较高且对环境友好,在环境水样中对羟基苯甲酸酯的检测方面有良好的应用潜力。