利用Raman散射光谱研究铜铟镓硒薄膜表面的掺杂调节作用

主要研究了采用溅射后硒化方法制备CIGS(铜铟镓硒)薄膜太阳电池的吸收体材料中的表面层掺杂调节问题。并利用Raman散射谱分析研究了样品表面层特征峰的移用,研究结果表明: CIGS薄膜表面层由富In表面层调节为富CuGa表面层后,Raman特征峰位向高波数移动,表明薄膜表面的Ga含量随之变化,并导致表面能带的相应改变,经计算证实了富CuGa表面层样品较之富In表面层样品具有更高的表面能带,从而改善了以此材料为吸收层的太阳电池器件性能, V_oc提高了74 mV,填充因子上升8％,最终使器件转换效率η相应提高了约2％。提高了V_oc与FF。同时表明Raman散射谱作为一种灵敏的表面表征手段,在研究太阳电池吸收层表面状态时十分有力。     

Influence of electric field on photoluminescence of Cu(In,Ga)Se<Subscript>2</Subscript>-based solar cells

The photoluminescence (PL) of solar cells, based on Cu(In,Ga)Se₂ and bare Cu(In,Ga)Se₂ absorbers, has been studied. Shapes and intensity dependencies of the PL spectra in the junctions and in thin films are compared and discussed in terms of influence of the junction field. Measurements of the photoluminescence in the cells biased in the forward direction are employed in order to show straightforwardly how electric field changes the radiative recombination rate.     

Improvement in efficiency of solar cell by removing Cu2－xSe from CIGS film surface

CIGS thin films are deposited by sputtering and selenization. The synthesis of semiconducting polycrystalline thin films and characteristics of devices based on the CIGS absorbing layers are investigated. Their microstructures are characterized by x-ray diffraction and Raman spectroscopy. The results reveal that there exist metallic Cu_2-xSe compounds in CIGS film surfaces and the compounds are thought to be responsible for the degradation of the open circuit voltage of solar cells. The optimization of selenization temperature profile and copper content in the precursor surfaces is studied, concluding that the conversion efficiency may be improved by removing metallic Cu_2-xSe compounds from the surfaces of CIGS thin films.     

硒化前后电沉积贫铜和富铜的Cu(In1-xGax)Se2薄膜成分及结构的比较

采用电沉积法获得了接近化学计量比的贫铜和富铜的Cu（In_1-xGa_x）Se₂（CIGS）预置层,研究比较了两种预置层及其硒化处理后的成分和结构特性.得到了明确的实验证据证明,硒化后富铜薄膜中的Cu_xSe相会聚集凝结成结晶颗粒分散在表面.研究表明：在固态源硒化处理后,薄膜成分基本不变;当预置层中原子比Cu/（In+Ga）<11时,硒化后薄膜表面存在大量的裂纹;而当Cu/（In+Ga） >12时,可以消除裂纹的产生,形成等轴状小晶粒;富铜预置层硒化时蒸发沉积少量In,Ga和Se后,电池效率已达到68%;而贫铜预置层硒化后直接制备的电池效率大于2%,值得进一步深入研究. 关键词： 1-xGa_x）Se₂薄膜')" href="#">Cu（In_1-xGa_x）Se₂薄膜 电沉积 硒化处理 贫铜或富铜薄膜     

Electric and magnetic properties of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/Pb(Zr<Subscript>0.52</Subscript>Ti<Subscript>0.48</Subscript>)O<Subscript>3</Subscript> bilayer thin films prepared by pulsed-laser deposition

CoFe₂O₄ (CFO) thin film with highly (111)-preferential orientation was first deposited on the silicon substrate by a pulsed-laser deposition, and then Pb(Zr_0.52Ti_0.48)O₃ (PZT) layers were deposited with different oxygen pressures to form the bilayer CFO/PZT nanocomposite thin films. X-ray diffraction showed that the PZT preferential orientation was strongly dependant on the oxygen pressure. The smooth film surface was obtained after depositing the CFO and PZT layers. The bilayer thin films exhibit good ferromagnetic and ferroelectric properties, and a low leakage current density of 0.004 μA/cm² at 50 kV/cm. The leakage current density curves show loops for the electric polarized field when the electric field reverses. PACS 77.84.Lf; 75.80+q; 81.05.Zx; 81.15.Fg     

Inkjet printed Cu(In,Ga)S<Subscript>2</Subscript> nanoparticles for low-cost solar cells

Cu(In,Ga)Se₂ (CIGSe) thin film solar cells were fabricated by direct inkjet printing of Cu(In,Ga)S₂ (CIGS) nanoparticles followed by rapid thermal annealing under selenium vapor. Inkjet printing is a low-cost, low-waste, and flexible patterning method which can be used for deposition of solution-based or nanoparticle-based CIGS films with high throughput. XRD and Raman spectra indicate that no secondary phase is formed in the as-deposited CIGS film since quaternary chalcopyrite nanoparticles are used as the base solution for printing. Besides, CIGSe films with various Cu/(In + Ga) ratios could be obtained by finely tuning the composition of CIGS nanoparticles contained in the ink, which was found to strongly influence the devices performance and film morphology. To date, this is the first successful fabrication of a solar device by inkjet printing of CIGS nanoparticles.     

Annealing study of electrodeposited CuInSe<Subscript>2</Subscript> and CuInS<Subscript>2</Subscript> thin films

In this study CuInSe₂ and CuInS₂ thin films were prepared onto ITO glass substrate using the electrodeposition technique in aqueous solution. The electrodeposited films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray analysis. The annealing effects on electrodeposited precursors were investigated. The chalcopyrite structure of CuInSe₂/CuInS₂ showed an enhancement of crystallinity after subsequent selenization/sulfurization treatment in Se/S atmosphere, respectively. XRD and SEM studies revealed a dramatic improvement of the crystalline quality of CIS films after annealing treatments. Mott–Schottky measurements were used to assess the conductivity type of the films and their carrier concentration. The prepared samples underwent an etching process to remove the binary accumulated Cu_2?x(Se,S) phases shown in FESEM pictures. This etching process has shown a noticeable decrease in both, the flat band potential, V_fb (V), and the number of acceptors, N_A (cm^?3) in selenized CuInSe₂ and sulfurized CuInS₂ samples.     

Microstructural evolution and electrical properties of La<Subscript>0.7</Subscript>Ca<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript> thin films grown on SrTiO<Subscript>3</Subscript> substrates by excimer-laser assisted metal-organic deposition

Thin films of La_0.7Ca_0.3MnO₃ were successfully grown epitaxially on (100) single-crystal SrTiO₃ substrates by excimer-laser assisted metal-organic deposition. Initial amorphous LCMO thin films were obtained by metal-organic deposition at 500 °C. Crystallization and epitaxial growth of the films was achieved using a KrF pulsed laser irradiation while the film/substrate samples were kept at 500 °C. High resolution transmission electron microscopy observations on cross-sections demonstrate the formation mechanism of the epitaxial films. The crystallization process starts at the LCMO/STO interface and grows by increasing the number of laser shots. A fully crystallized film was obtained after 5 min of irradiation. The film/substrate interface was found to be sharp and abrupt. The temperature dependence of the resistance R(T) shows various behaviors, starting from insulating to semiconducting and metal–insulator transition material during the formation of the manganite film. The oxygen content was also improved by increasing the irradiation time. Promising values of the temperature coefficient of resistance were obtained from these manganite films for prospect integration in silicon based microbolometric devices. PACS 81.15.-z; 81.15.Np; 73.61.-r; 71.30.+h     

Modulation of ultrafast laser-induced magnetization precession in BiFeO<Subscript>3</Subscript>-coated La<Subscript>0.67</Subscript>Sr<Subscript>0.33</Subscript>MnO<Subscript>3</Subscript> thin films

The ultrafast laser-excited magnetization dynamics of ferromagnetic (FM) La_0.67Sr_0.33MnO₃ (LSMO) thin films with BiFeO₃ (BFO) coating layers grown by laser molecular beam epitaxy are investigated using the optical pump-probe technique. Uniform magnetization precessions are observed in the films under an applied external magnetic field by measuring the time-resolved magneto-optical Kerr effect. The magnetization precession frequencies of the LSMO thin films with the BFO coating layers are lower than those of uncoated LSMO films, which is attributed to the suppression of the anisotropy field induced by the exchange interaction at the interface between the antiferromagnetic order of BFO and the FM order of LSMO.     

Photoluminescence behavior of pulsed laser deposited ZnGa<Subscript>2</Subscript>O<Subscript>4</Subscript> thin-film phosphors grown on various substrates

ZnGa₂O₄ thin-film phosphors have been grown on Si(100), Al₂O₃(0001) and MgO(100) substrates using pulsed laser deposition. The structural characterization was carried out on a series of ZnGa₂O₄ films grown on various substrates under various substrate temperatures and oxygen pressures. The films grown on these substrates not only have different crystallinity and surface morphology, but also different Zn/Ga composition ratio. The crystallinity and photoluminescence (PL) of the ZnGa₂O₄ films are highly dependent on the deposition conditions, in particular the stoichiometry ratio of Zn/Ga and the kind of substrate. The variation of Zn/Ga in the films also depends on not only the oxygen pressure but also the substrate temperature during deposition. The PL properties of pulsed laser deposited ZnGa₂O₄ thin films have indicated that Al₂O₃(0001) and MgO(100) are promising substrates for the growth of high-quality ZnGa₂O₄ thin films and that the luminescence brightness depends on the substrate. The luminescence spectra show a broad band extending from 350 to 600 nm and peaking at 460 nm. Received: 11 July 2002 / Accepted: 31 July 2002 / Published online: 28 October 2002 RID="*" ID="*"Corresponding author. Fax: +82-51-6206356, E-mail: jhjeong@pknu.ac.kr     

Nanostructured TiO<Subscript>2</Subscript> Films with a Mixed Phase for Perovskite Solar Cells

A series of thin films made with TiO₂ nanoparticles with a varied anatase/rutile phase ratio is prepared on conducting glass substrates using a spin-coating method. The structure, morphology, and optical properties of TiO₂ nanopowders and thin films fabricated are studied using powder X-ray diffraction, scanning electron microscopy, and optical spectroscopy. The TiO₂ nanostructured films created are used as photoelectrodes for the fabrication of perovskite solar cells (PSCs). The photovoltaic characteristics of PSCs under AM1.5 light illumination (1000 W/m²) under ambient conditions are studied. It is shown that the best efficiency of solar-to-electrical energy conversion, namely, 9.3%, is obtained for the PSC with a photoelectrode based on a TiO₂ film with an anatase/rutile mixed phase ratio of 86/14%.     

Micro-Raman spectroscopic investigation of NiSi films formed on BF<Subscript>2</Subscript><Superscript>+</Superscript>-, B<Superscript>+</Superscript>- and non-implanted (100)Si substrates

The micro-Raman spectroscopic technique was used to investigate vibrational properties of NiSi thin films formed on three different (100)Si substrates: non-implanted, 20 keV BF₂⁺-implanted, and 20 keV B⁺-implanted. Raman measurements were also performed on NiSi powder to identify various phonon modes associated with different selection rules of group theory. It was found that the Raman peaks for NiSi thin films formed on the BF₂⁺-implanted substrate were broader and shifted to lower frequencies compared to those for films formed on the other substrates. The broadening of the Raman peaks for these films, which also exhibit much improved thermal stability, is attributed to the small grains that probably result from the segregation of fluorine to grain boundaries and interfaces. It is further proposed that grain boundary segregation influences the stress in the silicide film, resulting in shifts in phonon peak positions. PACS 78.30.Am; 74.25.Kc; 68.35.Dv; 68.55.Ln; 66.30.Jt     

Bottom-up fabrication and piezoelectric properties of CaBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> micro-plateaus

CaBi₄Ti₄O₁₅ (CBTi144) micro-plateaus were fabricated on Si wafers and Pt foils using a self-assembled monolayer (SAM) and a complex metal alkoxide solution. The micro-plateaus are delineated by metal masks, which are used for shadowing against the ultraviolet (UV) irradiation for decomposition of SAM to make the surface hydrophilic. The micro-plateaus crystallized to a ferroelectric phase with random orientation. The crystallization depended on the SAM-derived ultra thin layers at the surface of the substrates. The primitive PFM measurements without any top electrodes confirmed that the micro-plateaus exhibited the piezoresponse behaviors. The piezoelectric constant, d₃₃, had some distribution, and the maximum d₃₃ was confirmed as about 45 pm/V, which is identical to the d₃₃ of the polar-axis oriented CBTi144 thin films. PACS 77.84.-s; 81.20.Fw; 77.65.-j     

Characterization of Zn<Subscript>2</Subscript>SnO<Subscript>4</Subscript> Thin Films Prepared by RF Magnetron Sputtering

Zn₂SnO₄ (ZTO) is a stable semiconductor in ZnO–SnO₂ system and important transparent conducting oxide (TCO) predominantly used in optoelectronic devices. ZTO thin films were prepared by RF magnetron sputtering using Zn₂SnO₄ ceramic target in this paper. The effects of annealing temperatures and oxygen contents on characterization of ZTO thin films were studied. The results show that ZTO thin films prepared by RF magnetron sputtering are amorphous with an optical band gap of 3.22 eV. After annealing at 650°C in Ar atmosphere for 40 min, ZTO films possess a spinel structure with an optical band gap of 3.62 eV. The atomic force microscope (AFM) data of morphology reveals that the surface roughness of films is about 2 nm. The results of energy dispersive spectrometer (EDS) show that the concentration ratio of Zn to Sn is in the range from 1.44 to 1.57. The results of Hall-effect-measurement system reveal that the resistivity of films varies from 102 to 10–1 Ωcm, carrier concentration is about 10¹⁷ cm^–3, and mobility ranges from 10⁰ to 10¹ cm² v^–1 s^–1.     

Large optical nonlinearity in CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> thin films

CaCu₃Ti₄O₁₂ (CCTO) thin films were successfully prepared on LaAlO₃ substrates by pulsed laser deposition technique. We measured the nonlinear optical susceptibility of the thin films using Z-scan method at a wavelength of 532 nm with pulse durations of 25 ps and 7 ns. The large values of the third-order nonlinear optical susceptibility, χ ⁽³⁾, of the CCTO film were obtained to be 2.79×10⁻⁸ esu and 3.30×10⁻⁶ esu in picosecond and nanosecond time regimes, respectively, which are among the best results of some representative nonlinear optical materials. The origin of optical nonlinearity of CCTO films was discussed. The results indicate that the CCTO films on LaAlO₃ substrates are promising candidate materials for applications in nonlinear optical devices.     

The film thickness dependent thermal stability of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>:Ag thin films as high-temperature solar selective absorbers

The monolayer Al₂O₃:Ag thin films were prepared by magnetron sputtering. The microstructure and optical properties of thin film after annealing at 700 °C in air were characterized by transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and spectrophotometer. It revealed that the particle shape, size, and distribution across the film were greatly changed before and after annealing. The surface plasmon resonance absorption and thermal stability of the film were found to be strongly dependent on the film thickness, which was believed to be associated with the evolution process of particle diffusion, agglomeration, and evaporation during annealing at high temperature. When the film thickness was smaller than 90 nm, the film SPR absorption can be attenuated until extinct with increasing annealing time due to the evaporation of Ag particles. While the film thickness was larger than 120 nm, the absorption can keep constant even after annealing for 64 h due to the agglomeration of Ag particles. On the base of film thickness results, the multilayer Al₂O₃:Ag solar selective thin films were prepared and the thermal stability test illustrated that the solar selectivity of multilayer films with absorbing layer thickness larger than 120 nm did not degrade after annealing at 500 °C for 70 h in air. It can be concluded that film thickness is an important factor to control the thermal stability of Al₂O₃:Ag thin films as high-temperature solar selective absorbers.     

Photoacoustic spectroscopy of thin films of As<Subscript>2</Subscript>S<Subscript>3</Subscript>, As<Subscript>2</Subscript>Se<Subscript>3</Subscript> and GeSe<Subscript>2</Subscript>

Photoacoustic spectroscopy (PAS) is one of the important branches of spectroscopy, which enables one to detect light-induced heat production following the absorption of pulsed radiation by the sample. As₂S₃, As₂Se₃ and GeSe₂ exhibit a wide variety of photo-induced phenomena that enable them to be used as optical imaging or storage medium and various electronic devices, including electro-optic information storage devices and optical mass memories. Therefore, accurate measurement of thermal properties of semiconducting films is necessary to study the memory density. The thermal conductivity of thin films of As₂S₃ (thickness 100 μm and 80 μm), As₂Se₃ (thickness 100 μm and 80 μm) and GeSe₂ (thickness 120 μm and 100 μm) has been measured using PAS technique. Our result shows that the thermal conductivity of thicker films is larger than the thinner films. This can be explained by the thermal resistance effect between the film and the surface of the substrate.      

Electrodiffusion phenomena in C<Subscript>60</Subscript> thin films

As part of our ongoing research program to produce semiconductor devices based on C₆₀ thin films, we report here on our first attempts at the intercalative doping of C₆₀ thin films through the diffusion of metals. Two techniques were employed: (a) chemically induced counter electrodiffusion of Cu and I₂ into a C₆₀ matrix and (b) Au diffusion under the action of an external electric field.     

Preparation of Cu（In,Ga）Se2 Thin Film Solar Cells by Selenization of Metallic Precursors in an Ar Atmosphere

Cu（In, Ga）Se2 thin films are deposited on Mo-coated glass substrates by Se vapour selenization of sputtered metallic precursors in the atmosphere of Ar gas flow under a pressure of about 10 Pa. The in situ heat treatment of as-grown precursor leads to the formation of a better alloy. During selenization, the growth of CuInSe2 phase preferably proceeds through Se-poor phases as CuSe and InSe at relatively low substrate temperature of 250℃, due to the absence of In2Se3 at intermediate stage at low reactor pressure. Subsequently, the Cu（In,Ga）Se2 phase is produced by the reactive diffusion of CuInSe2 with a Se-poor GaSe phase at high temperature of up to 560℃. The final film exhibits smooth surface and large grain size. The absorber is used to fabricate a glass/Mo/Cu（In, Ga）Se2/CdS/ZnO cell with the total-area efficiency of about 7%. The low open-circuit voltage value of the cell fabricated should result from the nonuniform distribution of In and Ga in the absorber, due to the diffusion-controlled reaction during the phase formation. The films, as well as devices, are characterized.     

Improved photoluminescence of pulsed-laser-ablated Y<Subscript>1-x</Subscript>Gd<Subscript>x</Subscript>VO<Subscript>4</Subscript>:Eu<Superscript>3+</Superscript> thin film phosphors by Gd substitution

Gd-substituted Y_1-xGd_xVO₄:Eu³⁺ luminescent thin films have been grown on Al₂O₃(0001) substrates using pulsed-laser deposition. The films grown under different deposition conditions have been characterized using microstructural and luminescent measurements. The crystallinity, surface morphology, and photoluminescence (PL) of the films are highly dependent on the amount of Gd. The photoluminescence (PL) brightness data obtained from Y_1-xGd_xVO₄:Eu³⁺ films grown under optimized conditions have indicated that the PL brightness is more dependent on the surface roughness than the crystallinity of the films. In particular, the incorporation of Gd into the YVO₄ lattice could induce a remarkable increase of PL. The highest emission intensity was observed with Y_0.57Gd_0.40Eu_0.03VO₄ thin film whose brightness was increased by a factor of 2.5 and 1.9 in comparison with that of YVO₄:Eu³⁺ and GdVO₄:Eu³⁺ films, respectively. This phosphor have application to flat panel displays. PACS 78.20.-e; 78.55.-m; 78.66.-w