Thermal behaviour and properties of Na<Subscript>2</Subscript>O-TiO<Subscript>2</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Differential scanning calorimetry (DSC) and thermomechanical analysis (TMA) were used to study the thermal behaviour of (50-x)Na₂O-xTiO₂-50P₂O₅ and 45Na₂O-yTiO₂-(55-y)P₂O₅ glasses. The addition of TiO₂ to the starting glasses (x=0 and y=5 mol% TiO₂) resulted in a nonlinear increase of glass transition temperature and dilatation softening temperature, whereas the thermal expansion coefficient decreased. All prepared glasses crystallize under heating within the temperature range of 300–610°C. The contribution of the surface crystallization mechanism over the internal one increases with increasing TiO₂ content. With increasing TiO₂ content the temperature of maximum nucleation rate is also gradually shifted from a value close to the glass transition temperature towards the crystallization temperature. X-ray diffraction measurements showed that the major compounds formed by glass crystallization were NaPO₃, TiP₂O₇ and NaTi₂(PO₄)₃. The chemical durability of the glasses without titanium oxide is very poor, but with the replacement of Na₂O or P₂O₅ by TiO₂, it increases sharply.     

Influence of composition on corroding process of Na<Subscript>2</Subscript>O-K<Subscript>2</Subscript>O-CaO-ZrO<Subscript>2</Subscript>-SiO<Subscript>2</Subscript> glasses

The corroding process of six glasses of the Na₂O-K₂O-CaO-ZrO₂-SiO₂ system with ZrO₂content 0–2.13 mass % by water was observed during static tests at 121°C and pressure of 0.25 MPa in steam sterilizer. Significant increase of Na⁺ and K⁺ content in leachates was observed after the addition of ZrO₂ into glass. Further increase of the content of ZrO₂ in glasses slowed down the rate of Na⁺ and K⁺ leaching. The leaching process of SiO₂ as well as Na⁺, K⁺, and Ca²⁺ ions was evaluated on the basis of comparison with model leaching processes. Variation of the concentrations of Na⁺, K⁺, Ca²⁺, and SiO₂ in leachates with time was described by empirical equation. Observed changes in the initial leaching rates of Na⁺, K⁺, Ca²⁺, and SiO₂ can be ascribed to the content of ZrO₂ in glasses. The presence of ZrO₂ in glasses reduced the overall rate of glass dissolution.     

Determination of the enthalpy of fusion of Na<Subscript>3</Subscript>FeF<Subscript>6</Subscript>

The areas of the fusion and crystallization peaks of Na₃FeF₆ and of four calibration substances (KCl, NaCl, Na₂SO₄, and K₂SO₄) were measured using the DSC mode of a high-temperature calorimeter. Using the measured quantities and known values of the enthalpy of fusion of the calibration substances, the enthalpy of fusion of Na₃FeF₆ was determined. Its value at the temperature of fusion 1224 K was 70 ± 4 kJ mol⁻¹.     

Synthesis and study of sodium triuranate Na<Subscript>2</Subscript>(UO<Subscript>2</Subscript>)<Subscript>3</Subscript>O<Subscript>3</Subscript>(OH)<Subscript>2</Subscript>

Sodium triuranate Na₂(UO₂)₃O₃(OH)₂ was synthesized by the reaction between aqueous uranyl acetate solution and aqueous sodium nitrate solution under hydrothermal conditions at 200°C. The composition and structure of the synthesized compound were determined, and its dehydration and thermal decomposition were studied, by chemical analysis, X-ray diffraction, IR spectroscopy, and thermal analysis.     

Solubility isotherm for the Na<Subscript>2</Subscript>MoO<Subscript>4</Subscript>-Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-H<Subscript>2</Subscript>O system

Solubility in the Na₂MoO₄-Na₂SO₄-H₂O system was studied using isothermal saturation at 5–100°C. The boundaries of crystallization fields were determined for sodium sulfate and sodium molybdate. Solid solutions were not observed within the range of the temperatures studied. The density, refractive index, and dynamic viscosity of the saturated solutions of the system were determined, and these data were used to calculate the molar volume, kinematic viscosity, and apparent molar volume of the sum of salts in these solutions. All property isotherms of solutions are in a strict correlation with the solubility in the system; this correlation is represented as an isobaric-isothermal diagram.     

Crystal Structure of New One-Dimensional Triple Molybdate Na<Subscript>2</Subscript>K<Subscript>2</Subscript>Cu(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>

The title compound (disodium dipotassium copper(II) tris-[molybdate (VI)]) is prepared by form melt and characterized by single crystal X-ray diffraction and UV-vis spectroscopy. It crystallizes in the triclinic space group P-1 with a = 7.4946(8) Å, b = 9.3428(9) Å, c = 9.3619(9) Å, α = 92.591(7)°, β = 105.247(9)°, γ = 105.496(9)°, V = 604.7 ų, and Z = 2. Its structure is isotypic with that of Na₄Mn(MoO₄)₃. It is formed by Cu₂O₁₀ distorted bi-octahedral dimers linked by two bridging bidentate Mo₂O₄ tetrahedra and, additionally, two monodentate Mo₁O₄ tetrahedra to form Cu₂Mo₄O₂₀ units. These units are linked by the insertion of Mo₃O₄ tetrahedra to build infinite ribbons disposed along the c axis. All of these ribbons form a one-dimensional framework. Both K1 and K3 cations are located in the inversion center, and all the other atoms are at general positions. The structure model is supported by the bond valence sum (BVS) and charge distribution CHARDI methods. The Cu²⁺ cations adopt the [4+2] CuO₆ Jahn-Teller distortion giving rise to an intense d–d transition in the UV-vis absorption spectra.     

Electrotransport properties of ions in aqueous solutions of H<Subscript>2</Subscript>SeO<Subscript>4</Subscript> and Na<Subscript>2</Subscript>SeO<Subscript>4</Subscript>

Coefficients of self-diffusion, absolute speeds of movement of ions and the activation energy of electrical conductivity are found from the conductance measurements of aqueous solutions of selenic acid and sodium selenate at different concentrations in a temperature range of 288–318 K. Both the Stokes and effective radii of ions and their hydrate numbers at 298 K are calculated. The obtained results are interpreted in the frames of Samoilov theory on positive and negative hydration of ions.     

Hydrothermal synthesis,characterization, and thermal properties of alumino silicate azide sodalite,Na<Subscript>8</Subscript>[AlSiO<Subscript>4</Subscript>]<Subscript>6</Subscript>(N<Subscript>3</Subscript>)<Subscript>2</Subscript>

First time we report the synthesis, structural characterization and thermal behavior of an unusual N₃ ^? containing alumino-silicate sodalite mineral. Azide sodalite, Na₈[AlSiO₄]₆(N₃)₂ has been synthesized under hydrothermal conditions at 433 K in steel lined Teflon autoclave. The structural and microstructural properties of azide sodalite mineral was characterized by various methods including FT-IR, XRD, SEM, TGA, and MAS NMR. Crystal structure have been refined by Rietveld method in \(P\bar 43n\) space group, indicating that the N₃ ^? sodalite has cubic in lattice. High temperature study was carried out to see the effect of thermal expansion on cell dimension (a ^o) of azide sodalite. Thermal behavior of sodalite was also assessed by thermogravimetric method.     

Non-isothermal kinetics of the thermal decomposition of sodium oxalate Na<Subscript>2</Subscript>C<Subscript>2</Subscript>O<Subscript>4</Subscript>

The thermal transformation of Na₂C₂O₄ was studied in N₂ atmosphere using thermo gravimetric (TG) analysis and differential thermal analysis (DTA). Na₂C₂O₄ and its decomposed product were characterized using a scanning electron microscope (SEM) and the X-ray diffraction technique (XRD). The non-isothermal kinetic of the decomposition was studied by the mean of Ozawa and Kissinger–Akahira–Sunose (KAS) methods. The activation energies (E _α) of Na₂C₂O₄ decomposition were found to be consistent. Decreasing E _α at increased decomposition temperature indicated the multi-step nature of the process. The possible conversion function estimated through the Liqing–Donghua method was ‘cylindrical symmetry (R₂ or F_1/2)’ of the phase boundary mechanism. Thermodynamic functions (ΔH*, ΔG* and ΔS*), calculated by the Activated complex theory and kinetic parameters, indicated that the decomposition step is a high energy pathway and revealed a very hard mechanism.     

Viscosity and shrinkage of porous and quartzoid glasses of the Na<Subscript>2</Subscript>O-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> system

Shrinkage of porous glasses on heating from 20 to 800°C was studied and temperature dependences of the viscosity in the range of 10¹¹–10¹³ P were determined for quartzoid (sintered) glasses based on five glasses with different compositions in the Na₂O-B₂O₃-SiO₂ system. The shrinkage of porous glasses and the viscosity of quartzoid glasses were analyzed in relation to their composition and temperature of preliminary thermal treatment.     

Structure and electric properties of Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-NaPO<Subscript>3</Subscript> glasses

The influence of the SO₄²⁻ ion on the temperature and concentration dependences of electric conductivity and the structure of sodium phosphate oxide glasses was studied. The increased electric conductivity of sulfate-phosphate glasses was explained by the formation of mixed sulfate-phosphate fragments with terminal SO₄²⁻ ions in the structure of glasses in the Na₂SO₄-NaPO₃ system. The dissociation energies of the sodium sulfate fragments are lower than those of pure oxide sodium phosphate structural units. As a result, the number of dissociated sodium ions increases, the activation energy of electric conductivity falls, and the conductivity (at 25°C) increases approximately 270-fold relative to the conductivity of NaPO₃. The arrangement of SO₄²⁻ ions in the structure was evaluated from the IR spectra of the glasses.     

Study on the non-isothermal kinetics of decomposition of 4Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>·2H<Subscript>2</Subscript>O<Subscript>2</Subscript>·NaCl

The non-isothermal decomposition kinetics of 4Na₂SO₄·2H₂O₂·NaCl have been investigated by simultaneous TG-DSC in nitrogen atmosphere and in air. The decomposition processes undergo a single step reaction. The multivariate nonlinear regression technique is used to distinguish kinetic model of 4Na₂SO₄·2H₂O₂·NaCl. Results indicate that the reaction type Cn can well describe the decomposition process, the decomposition mechanism is n-dimensional autocatalysis. The kinetic parameters, n, A and E are obtained via multivariate nonlinear regression. The n ^th-order with autocatalysis model is used to simulate the thermal decomposition of 4Na₂SO₄·2H₂O₂·NaCl under isothermal conditions at various temperatures. The flow rate of gas has little effect on the decomposition of 4Na₂SO₄·2H₂O₂·NaCl.     

Synthesis and ionic conduction of sodium titanate Na<Subscript>2</Subscript>Ti<Subscript>3</Subscript>O<Subscript>7</Subscript>

Chemical and phase transformations in the course of synthesis of sodium titanate Na₂Ti₃O₇ have been studied. Prepared sodium titanates have been characterized by X-ray powder diffraction analysis, scaning electron microscopy, and impedance spectroscopy, their electrochemical testing has been conducted. Mechanochemical interaction of titanium dioxide and sodium carbonate at the grinding stage has been revealed. The utilization of mesoporous titanium dioxide have been shown to provide a considerable decrease of final annealing temperature. Thus obtained titanates exhibit high electrochemical capacity.     

Systems Li<Subscript>2</Subscript>O(Na<Subscript>2</Subscript>O)-CdO-V<Subscript>2</Subscript>O<Subscript>5</Subscript>: Phase composition and phase diagrams

The subsolidus phase composition of the M₂O-CdO-V₂O₅ systems with M = Li or Na is studied. Double orthovanadates MCdVO₄ and MCd₄(VO₄)₃ form solid solutions of composition Li_{1 ? 2x/3}Cd _x/3CdVO₄ (0 ≤ x ≤ 1, orthorhombic space group Cmcm, modulation at x = 0.6) and Na_{3 ? 2x} Cd_{3 + x} (VO₄)₃ (0 ≤ x ≤ 0.10 and 0.30 ≤ x ≤ 1, orthorhombic space group Cmcm and Pn2₁ a or Pnma, respectively). In the range 0.10 < x < 0.30, the end-members of the solid solutions coexist. Isothermal sections of the systems are mapped.     

Thermal stability of layered perovskite-like oxides NaNdTiO<Subscript>4</Subscript> and Na<Subscript>2</Subscript>Nd<Subscript>2</Subscript>Ti<Subscript>3</Subscript>O<Subscript>10</Subscript>

Thermal stabilities of layered perovskite-like oxides NaNdTiO₄ and Na₂Nd₂Ti₃O₁₀ were studied in the temperature ranges from 780 to 1100°C and from 1100 to 1400°C, respectively. Chemical mechanism of their thermal decomposition was proposed. Higher thermal stability of Na₂Nd₂Ti₃O₁₀ was rationalized on the basis of crystallochemical data.     

Synthesis of sodium tungstate from the system Na<Subscript>2</Subscript>C<Subscript>2</Subscript>O<Subscript>4</Subscript>-NaNO<Subscript>3</Subscript>-WO<Subscript>3</Subscript>

The physicochemical basis of the heterogeneous reaction between the components of the system (sodium oxalate)-(sodium nitrate)-(tungsten(VI) oxide) has been studied. The reaction of WO₃ with sodium oxalate-nitrate mixtures occurs at a lower temperature and at a higher rate than the reaction with pure sodium carbonate. A high-yield process for the synthesis of high-purity sodium tungstate has been developed on the basis of this study.     

Solubility in the ternary system CaSO<Subscript>4</Subscript> + Na<Subscript>2</Subscript>SO<Subscript>4</Subscript> + H<Subscript>2</Subscript>O at 298.15 K

The solubility in the ternary system, aqueous mixture of CaSO₄ and Na₂SO₄, at T = 298.15 K comprises five different salts: calcium sulfate dihydrate, mirabilite, thenardite, glauberite and labile salt. Using the Extended Pitzer’s Ion Interaction model for pure and mixed electrolyte solutions and criteria of phase equilibria, predicted solubility behavior of salts was compared with experimental results from literature. The agreement between calculated and experimental solubilities was excellent in the ionic strength range up to 10.9062 mol kg⁻¹.     

Crystal Structure of Tl<Subscript>2</Subscript>[NbCl<Subscript>6</Subscript>] and Tl<Subscript>2</Subscript>[NbBr<Subscript>6</Subscript>]

Single crystals of Tl₂[NbCl₆] (1) and Tl₂ [NbBr₆] (2) are obtained as black needles on heating TlCl, Nb, S₂Cl₂ (1) and Tl, Nb, and Br₂ at 400°C (2). Tl₂NbBr₆ also forms in the reaction of TlBr, Nb, Br₂, and S at 500°C. Both compounds crystallize in the K₂[PtCl₆] structure type to form non-distorted octahedral [NbХ₆]^2– anions (Nb–Cl 2.397(4) Å and Nb–Br 2.516(2) Å). The magnetic properties of Tl₂[NbBr₆] in a range 5-300 K indicate an antiferromagnetic interaction between Nb⁴⁺ ion spins (d¹, S = 1/2). On cooling, the compound becomes a noncollinear ferromagnet with T_c = 23 K.     

A study of phase formation in the subsolidus region of the system Na<Subscript>2</Subscript>MoO<Subscript>4</Subscript>-MnMoO<Subscript>4</Subscript>-Cr<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>

Phase relationships in the subsolidus region of the system Na₂MoO₄-MnMoO₄-Cr₂(MoO₄)₃ were studied by means of X-ray diffraction and differential-thermal analyses. The possibility of obtaining a variablecomposition phase Na_1?x Mn_1?x Cr_1+x (MoO₄)₃ (0 ≤ x ≤ 0.5) and ternary molybdate NaMn₃Cr(MoO₄)₅ was examined. The temperature dependence of the conductivity of the phase Na_1?x Mn_1?x Cr_1+x (MoO₄)₃ was analyzed.