Lithium polyacrylate-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode materials with excellent performance for lithium ion batteries

A novel facile approach to coat LiMn₂O₄ by lithium polyacrylate (PAALi) is demonstrated. The PAALi-coated LiMn₂O₄ (LMO@2%PAALi) and LiMn₂O₄ (LMO) are characterized by charge–discharge tests, X-ray diffraction (XRD), PAALi dissolving experiment, transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetry (TG), and inductively coupled plasma optical emission spectrometer (ICP-OES). XRD and FTIR analyses indicate that there are no clear differences between LMO@2%PAALi and LMO. PAALi dissolving experiment indicates that PAALi is indissolvable in LiPF₆-EC/DMC/EMC electrolyte. TEM results reveal that LiMn₂O₄ particles are coated by PAALi. ICP-OES results indicate that this stable PAALi coating can prevent the Mn ions dissolving from active LiMn₂O₄ materials and then the stability of LiMn₂O₄ crystals in electrolyte are greatly enhanced. These unique features ensure that LMO@2%PAALi possesses much better rate performance, higher discharge capacity, better cycling performance, and lower charge transfer resistance over LMO. The discharge capacity of LMO@2%PAALi at 0.2 C reaches up to 127.2 mAh g^?1 at room temperature.     

Enhanced electrochemical properties of LiMnPO<Subscript>4</Subscript>/C via Li-site substitution with Mg

Li_0.94Mg_0.03MnPO₄/C composite cathode materials for lithium ion battery with different carbon contents are synthesized by sol–gel method followed by heat treatment in the air. Environmental scanning electron microscopy measurements show that both firing temperature and carbon content affect the morphology of the end products. X-ray powder diffraction analysis indicates that the samples are olivine-structured. The galvanostatic charge–discharge results show that the optimal firing temperature registers 400 °C and that the electrochemical performances of Li_0.94Mg_0.03MnPO₄/C are improved by elevating its carbon amount. The sample with an initial conductive carbon content of 20 wt.% gives the best performances; when tested at the rate of 0.02C, 0.1C, and 1.0C between 2.8 and 4.4 V, its initial discharge capacity reaches 145.8, 103.0, and 72.8 mAhg⁻¹, respectively, and maintains at 100.1, 77.6, and 65.4 mAhg⁻¹, respectively, after 100 cycles.     

Dandelion-like mesoporous Co<Subscript>3</Subscript>O<Subscript>4</Subscript> as anode materials for lithium ion batteries

A dandelion-like mesoporous Co₃O₄ was fabricated and employed as anode materials of lithium ion batteries (LIBs). The architecture and electrochemical performance of dandelion-like mesoporous Co₃O₄ were investigated through structure characterization and galvanostatic charge/discharge test. The as-prepared dandelion-like mesoporous Co₃O₄ consisted of well-distributed nanoneedles (about 40 nm in width and about 5 μm in length) with rich micropores. Electrochemical experiments illustrated that the as-prepared dandelion-like mesoporous Co₃O₄ as anode materials of LIBs exhibited high reversible specific capacity of 1430.0 mA h g^?1 and 1013.4 mA h g^?1 at the current density of 0.2 A g^?1 for the first and 100th cycle, respectively. The outstanding lithium storage properties of the as-prepared dandelion-like mesoporous Co₃O₄ might be attributed to its dandelion-like mesoporous nanostructure together with an open space between adjacent nanoneedle networks promoting the intercalation/deintercalation of lithium ions and the charge transfer on the electrode. The enhanced capacity as well as its high-rate capability made the as-prepared dandelion-like mesoporous Co₃O₄ to be a good candidate as a high-performance anode material for LIBs.     

Fabrication and electrochemical investigation of Li<Subscript>0.5</Subscript>TiO<Subscript>2</Subscript> as anode materials for lithium ion batteries

Hexagonal and cubic Li_0.5TiO₂ particles have been fabricated through magnesiothermic reduction of Li₂TiO₃ particles in a temperature range of 600 to 640 °C. The prolonged reduction time results in lattice transition from hexagonal to cubic structure of Li_0.5TiO₂. Their microstructures, valance state, chemical composition, as well as electrochemical performance as anode candidates for lithium ion batteries have been characterized and evaluated. The hexagonal Li_0.5TiO₂ exhibits better electrochemical activity compared with the cubic one. Further, the carbon-coated hexagonal Li_0.5TiO₂ displays improved electrochemical performance with initial reversible capacity of 176.6 mAh g^?1 and excellent cyclic behavior except capacity fading in the initial 10 cycles, which demonstrate a novel anode candidate for long lifetime lithium ion batteries.     

ZnO-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode material for lithium-ion batteries synthesized by a combustion method

ZnO-coated LiMn₂O₄ cathode materials were prepared by a combustion method using glucose as fuel. The phase structures, size of particles, morphology, and electrochemical performance of pristine and ZnO-coated LiMn₂O₄ powders are studied in detail by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), galvanostatic charge-discharge test, and X-ray photoelectron spectroscopy (XPS). XRD patterns indicated that surface-modified ZnO have no obvious effect on the bulk structure of the LiMn₂O₄. TEM and XPS proved ZnO formation on the surface of the LiMn₂O₄ particles. Galvanostatic charge/discharge test and rate performance showed that the ZnO coating could improve the capacity and cycling performance of LiMn₂O₄. The 2 wt% ZnO-coated LiMn₂O₄ sample exhibited an initial discharge capacity of 112.8 mAh g^?1 with a capacity retention of 84.1 % after 500 cycles at 0.5 C. Besides, a good rate capability at different current densities from 0.5 to 5.0 C can be acquired. CV and EIS measurements showed that the ZnO coating effectively reduced the impacts of polarization and charge transfer resistance upon cycling.     

Enhanced electrochemical performance of lithium ion battery cathode Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C

Li-ion battery cathode material lithium-vanadium-phosphate Li₃V₂(PO₄)₃ was synthesized by a carbon-thermal reduction method, using stearic acid, LiH₂PO₄, and V₂O₅ as raw materials. And stearic acid acted as reductant, carbon source, and surface active agent. The effect of its content on the crystal structure and electrochemical performance of Li₃V₂(PO₄)₃/C were characterized by XRD and electrochemical performance testing, respectively. The results showed that the content of carbon source has no significant effect on the crystal structure of lithium vanadium phosphate. Lihtium vanadium phosphate obtained with 12.3% stearic acid demonstrated the best electrochemical properties with a typical discharge capacity of 119.4 mAh/g at 0.1 C and capacity retention behavior of 98.5% after 50 cycles. And it has high reversible discharge capacity of 83 mAh/g at 5 C with the voltage window of 3 to 4.3 V.     

Synthesis and characterization of pristine Li<Subscript>2</Subscript>MnSiO<Subscript>4</Subscript> and Li<Subscript>2</Subscript>MnSiO<Subscript>4</Subscript>/C cathode materials for lithium ion batteries

The cathode materials, pristine Li₂MnSiO₄ and carbon-coated Li₂MnSiO₄ (Li₂MnSiO₄/C), were synthesized by the sol–gel method. Power X-ray diffraction and scanning electron microscopy analyses show that the presence of carbon during synthesis can weaken the formation of impurities in the final product and decrease the particle size of the final product. The effects of carbon coating on electrochemical characteristics were investigated by galvanostatic cycling test and electrochemical impedance spectroscopy. The galvanostatic cycling test results indicate that Li₂MnSiO₄/C cathode exhibits better electrochemical performance with an initial discharge capacity of 134.4 mAh g⁻¹ and a capacity retention of 63.9 mAh g⁻¹ after 20 cycles. Electrochemical impedance analyses confirm that carbon coating can increase electronic conductivity, which results in good electrochemical performance of Li₂MnSiO₄/C cathode. The two semicircles and the large arc obtained in this study can be attributed to the migration of lithium ions through the solid electrolyte interphase films, the electronic properties of the material, and the charge transfer step, respectively.     

Influence of co-precipitation temperature on microstructure and electrochemical properties of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> cathode materials for lithium ion batteries

The layered Li-rich Mn-based cathode materials Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ were prepared by using co-precipitation technique at different temperatures, and their crystal microstructure and particle morphology were observed and analyzed by XRD and SEM. The electrochemical properties of these samples were investigated by using charge-discharge tests, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV), respectively. The results indicated that all samples are of high purity. When the precursors were co-precipitated at 50 °C, their cathode materials have the most uniform and full particles and exhibit the highest initial discharge capacity (289.4 mAh/g at 0.1C), the best cycle stability (capacity retention rate of 91.2 % after 100 cycles at 0.5C), and the best rate performance. The EIS results show that the lower charge transfer resistance of 50 °C sample is responsible for its superior discharge capacity and rate performance.     

LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> hollow nano-micro hierarchical microspheres as advanced cathode for lithium ion batteries

The high-voltage spinel-type LiNi_0.5Mn_1.5O₄ (LNMO) is a promising cathode material for next-generation lithium ion batteries. In this study, hollow LNMO microspheres have been synthesized via co-precipitation method accompanied with high-temperature calcinations. The physical and electrochemical properties of the materials are characterized by x-ray diffraction (XRD), TGA, RAMAN, CV, scanning electron microscope (SEM), transmission electon microscopy (TEM), electrochemical impendence spectroscopy (EIS), and charge-discharge tests. The results prove that the microspheres combine hollow structures inward and own a cubic spinel structure with space group of Fd-3m, high crystallinity, and excellent electrochemical performances. With the short Li⁺ diffusion length and hollow structure, the hierarchical LNMO microspheres exhibit 138.2 and 108.5 mAh g^?1 at 0.5 and 10 C, respectively. Excellent cycle stability is also demonstrated with more than 98.8 and 88.2 % capacity retention after 100 cycles at 1 and 10 C, respectively.     

Synthesis and electrochemical performance of LiFePO<Subscript>4</Subscript>/C cathode materials from Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> for high-power lithium-ion batteries

Carbon-coated olivine-structured LiFePO₄/C composites are synthesized via an efficient and low-cost carbothermal reduction method using Fe₂O₃ as iron source at a relative low temperature (600 °C). The effects of two kinds of carbon sources, inorganic (acetylene black) and organic (sucrose), on the structures, morphologies, and lithium storage properties of LiFePO₄/C are evaluated in details. The particle size and distribution of the carbon-coated LiFePO₄ from sucrose (LiFePO₄/SUC) are more uniform than that obtained from acetylene black (LiFePO₄/AB). Moreover, the LiFePO₄/SUC nanocomposite shows superior electrochemical properties such as high discharge capacity of 156 mAh g^?1 at 0.1 C, excellent cyclic stability, and rate capability (78 mAh g^?1 at 20 C), as compared to LiFePO₄/AB. Cyclic voltammetric test discloses that the Li-ion diffusion, the reversibility of lithium extraction/insertion, and electrical conductivity are significantly improved in LiFePO₄/SUC composite. It is believed that olivine-structured LiFePO₄ decorated with carbon from organic carbon source (sucrose) using Fe₂O₃ is a promising cathode for high-power lithium-ion batteries.     

Synthesis and electrochemical performance of carbon-coated LiMnBO<Subscript>3</Subscript> as cathode materials for lithium-ion batteries

Carbon-coated LiMnBO₃/C is synthesized by a sol-gel method using polyethylene glycol 6000 (PEG-6000) as carbon source. The influences of different sintering temperatures on the crystal structure, morphology, and electrochemical performance of LiMnBO₃/C composites are investigated. XRD results indicate that the samples consist of the monoclinic phase LiMnBO₃ (m-LiMnBO₃) and the hexagonal phase LiMnBO₃ (h-LiMnBO₃), and the amount of m-LiMnBO₃ is reduced and the h-LiMnBO₃ is increased with the increasing sintering temperature. The particle size of the samples is about 500 nm, and the surface of the particles is coated with a thick amorphous carbon layer. The LiMnBO₃/C synthesized at 750 °C exhibits the initial discharge capacities of 213.4, 170.8, and 109.7 mAh g^?1 at 0.025, 0.05, and 0.5 C rates, respectively, and shows better cycling performance than that of bare LiMnBO₃. The enhanced electrochemical performance might be largely attributed to the uniformly coated carbon layers from decomposition of the PEG-6000.     

Synthesis and electrochemical performance of carbon-coated LiCoBO<Subscript>3</Subscript> as cathode materials for lithium-ion batteries

Carbon-coated LiCoBO₃ (LiCoBO₃/C) is prepared by sol-gel method and polyethylene glycol 6000 (PEG-6000) is chosen as carbon source. The LiCoBO₃/C sample exhibits an initial discharge capacity of 76.7 mAh g^?1 at 0.1 C, and it can deliver a discharge capacity of 65.9 mAh g^?1 after 50 cycles, while the LiCoBO₃ sample only presents a first discharge capacity of 34.3 and 16.8 mAh g^?1 at the 50th cycle, LiCoBO₃/C sample shows better cycling performance than that of LiCoBO₃. The improved electrochemical properties could be mainly ascribed to the conductive carbon network and the reduced particle size of the LiCoBO₃ powders. Electrochemical impedance spectroscopy (EIS) results confirm that carbon coating decreases the charge transfer resistance and improve the electrochemical reaction kinetics.     

Enhanced electrochemical performances of Li<Subscript>2</Subscript>MnO<Subscript>3</Subscript> cathode materials by Al doping

Al-doped Li₂MnO₃ (Li₂Mn_0.9Al_0.1O₃) lithium-rich layered oxide is prepared and investigated as cathode material for lithium-ion batteries (LIBs). X-ray diffraction (XRD) and scanning electron microscopy-energy dispersive spectrometer (SEM-EDS) analyses reveal that the Al element is distributed in the sample homogenously. The Al-LMO sample exhibits a great improvement on the rate capability and cycling stability compared to the LMO sample. The differential capacity versus voltage (dQ/dV) results reveal that Al doping would be to prevent the first charge phase transformation from a layered phase to a cubic spinel-like phase and also slowdown the rate of transformation upon cycling. Electrochemical impedance spectroscopy (EIS) results confirm that Al doping decreases the charge-transfer resistance and improves the electrochemical reaction kinetics.     

Electrochemical comparison of LiFe<Subscript>0.4</Subscript>Mn<Subscript>0.595</Subscript>Cr<Subscript>0.005</Subscript>PO<Subscript>4</Subscript>/C and LiMnPO<Subscript>4</Subscript>/C cathode materials

A comparison of electrochemical performance between LiFe_0.4Mn_0.595Cr_0.005PO₄/C and LiMnPO₄/C cathode materials was conducted in this paper. The cathode samples were synthesized by a nano-milling-assisted solid-state process using caramel as carbon sources. The prepared samples were investigated by XRD, SEM, TEM, energy-dispersive X-ray spectroscopy (EDAX), powder conductivity test (PCT), carbon-sulfur analysis, electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge cycling. The results showed that LiFe_0.4Mn_0.595Cr_0.005PO₄/C exhibited high specific capacity and high energy density. The initial discharge capacity of LiFe_0.4Mn_0.595Cr_0.005PO₄/C was 163.6 mAh g^?1 at 0.1C (1C = 160 mA g^?1), compared to 112.3 mAh g^?1 for LiMnPO₄/C. Moreover, the Fe/Cr-substituted sample showed good cycle stability and rate performance. The capacity retention of LiFe_0.4Mn_0.595Cr_0.005PO₄/C was 98.84 % over 100 charge-discharge cycles, while it was only 86.64 % for the pristine LiMnPO₄/C. These results indicated that Fe/Cr substitution enhanced the electronic conductivity for the prepared sample and facilitated the Li⁺ diffusion in the structure. Furthermore, LiFe_0.4Mn_0.595Cr_0.005PO₄/C composite presented high energy density (606 Wh kg^?1) and high power density (574 W kg^?1), thus suggested great potential application in lithium ion batteries (LIBs).     

Study on electrochemical performance of Mg-doped Li<Subscript>2</Subscript>FeSiO<Subscript>4</Subscript> cathode material for Li-ion batteries

In this paper, Li₂Fe_1?yMg_ySiO₄/C (y?=?0, 0.01, 0.02, 0.03, 0.05), a cathode material for lithium-ion battery was synthesized by solid-state method and modified by doping Mg²⁺ on the iron site. The effects of Mg²⁺ doping on the crystal structure and electrochemical performance Li₂FeSiO₄ was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrochemical tests. Electrochemical methods of measurement were applied including constant current charge–discharge test, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), to determine the electrochemical performance of the material and the optimal doping ion and ratio. The results showed that Li₂Fe_0.98Mg_0.02SiO₄/C has the higher specific capacity and better cycle stability as well as lower impedance and better reversibility. The enhanced electrochemical performance can be attributed to the increased electronic conductivity, the decreased charge transfer impedance, and the improved Li-ion diffusion coefficient. Then, further study on the synthesis conditions was performed to find the optimal combustion temperature and time. According to the study, the material which has the best electrochemical performance, shows initial discharge specific capacity of 142.3 mAh g^?1 at 0.1 C (1 C?=?166 mA g^?1) and coulomb efficiency of 95.6%, under the condition that the temperature is 700 °C and the calcining time is 10 h.     

Acacia gum-assisted co-precipitating synthesis of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion batteries

LiNi_0.5Co_0.2Mn_0.3O₂ particles of uniform size were prepared through carbonate co-precipitation method with acacia gum. The precursor of carbonate mixture was calcined at 800 °C, and a well-crystallized Ni-rich layered oxide was got. The phase structure and morphology were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The micro-sized particles delivered high initial discharge capacity of 164.3 mA h g^?1 at 0.5 C (1 C?=?200 mA g^?1) between 2.5 and 4.3 V with capacity retention of 87.5 % after 100 cycles. High reversible discharge capacities of 172.4 and 131.4 mA h g^?1 were obtained at current density of 0.1 and 5 C, respectively. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were performed to further study the LiNi_0.5Co_0.2Mn_0.3O₂ particles. Anyway, the excellent electrochemical performances of LiNi_0.5Co_0.2Mn_0.3O₂ sample should be attributed to the use of acacia gum.     

Effect of molybdenum on Li<Subscript>2</Subscript>Mn<Subscript>4</Subscript>O<Subscript>9</Subscript> for rechargeable lithium ion batteries

Li₂Mn₄O₉ and molybdenum-doped Li₂Mn₄O₉ have been prepared by simple solid-state method. Molybdenum is used as a dopant since it is resistant to both corrosion and high-temperature creep deformation. The structural, morphological, and electrical performances of the samples have been analyzed. The material exhibits a cubic structure with the fd3m space group. Using EDAX, the chemical compositions of the samples have been identified. The dc electrical conductivity of the Mo-doped (LM2) sample is found to be increased to 7.44?×?10^?6 S cm^?1 at 393 K. The enhanced electrical property of the molybdenum-doped Li₂Mn₄O₉ reveals it as a feasible cathode material for rechargeable Li-ion batteries.     

Effects of lithium excess amount on the microstructure and electrochemical properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode material

Spinel LiNi_0.5Mn_1.5O₄ cathode materials with different lithium excess amount (0, 2%, 6%, 10%) were synthesized by a facile solid-state method. The effect of lithium excess amount on the microstructure, morphology, and electrochemical properties of LiNi_0.5Mn_1.5O₄ materials was systematically investigated. The results show that the lithium excess amount does not change the particle morphology and size obviously; thus, the electrochemical properties of LiNi_0.5Mn_1.5O₄ are mainly determined by structural characteristics. With the increase of lithium excess amount, the cation disordering degree (Mn³⁺ content) and phase purity first increase and then decrease, while the cation mixing extent has the opposite trend. Among them, the LiNi_0.5Mn_1.5O₄ material with 6% lithium excess amount exhibits higher disordering degree and lower impurity content and cation mixing extent, thus leading to the optimum electrochemical properties, with discharge capacities of 125.0, 126.1, 124.2, and 118.9 mAh/g at 0.2-, 1-, 5-, and 10-C rates and capacity retention rate of 96.49% after 100 cycles at 1-C rate.     

Influence of cooling mode on the electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode materials for lithium-ion batteries

Li₄Ti₅O₁₂ (LTO) was synthesized with two different cooling methods by solid-state method, namely fast cooling and air cooling. The samples were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), galvanostatic charge–discharge test, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), respectively. XRD revealed that the basic LTO structure was not changed. FESEM images showed that fast cooling effectively reduced the particle sizes and the agglomeration of particles. Galvanostatic charge–discharge test showed that the air cooling sample exhibited a mediocre performance, having an initial discharge capacity of 136.3mAh?·?g^?1 at 0.5 C; however, the fast cooling sample demonstrated noticeable improvement in both of its discharge capacity and rate capability, with a high initial capacity value of 142.7 mAh?·?g^?1 at 0.5 C. CV measurements also revealed that fast cooling enhanced the reversibility of the LTO. EIS confirmed that fast cooling resulted in lower electrochemical polarization and a higher lithium-ion diffusion coefficient. Therefore, fast cooling have a great impact on discharge capacity, rate capability, and cycling performance of LTO anode materials for lithium-ion batteries.     

Role of mesopores on the electrochemical performance of LiCoO<Subscript>2</Subscript> composite cathodes for lithium ion batteries

Mesoporous carbon (MC) was utilized to increase the mesoporosity of LiCoO₂ composite cathode. Graphite powder (GP) was chosen as a standard of comparison because of its very low mesoporosity. Compared with MC, GP has similar particle size, lower specific surface area, and higher electronic conductivity. Acetylene black (AB) exists in the form of chains of nanoparticles. With all other factors held constant, the mixture of AB and MC (ABMC)-loaded LiCoO₂ composite cathode (ABMC cathode) was superior to the mixture of AB and GP (ABGP)-loaded LiCoO₂ composite cathode (ABGP cathode). The reason is described as follows. Both GP and MC form a conductive network with AB chains. ABGP cathode has higher electronic conductivity than ABMC cathode. But the ionic conductivity of the ABMC cathode is more easily enhanced than the ABGP cathode because the former has much greater mesoporosity. In addition, the mesopores absorb and retain electrolyte solution and then provide buffer lithium ions for quick electrochemical reactions, so shortening the lithium ion transfer path in the composite cathode.