原位诱导生长法制备单分散M型钡铁氧体亚微空心球

提出了一种制备单分散M型钡铁氧体空心球的新方法,即以碳酸胍表面改性的单分散聚(苯乙烯-共-丙烯酸)P(St-co-AA)乳胶粒子为模板,在其表面原位诱导钡铁氧体前驱物的定位并生长,以此获得壳层均匀致密的P(St-co-AA)/钡铁氧体前驱物核壳复合粒子,再经过热处理得到结构完整、成分单一的M型钡铁氧体空心球.     

均匀共沉淀法制备钛酸钡-钡铁氧体核-壳结构粒子

用均匀共沉淀法制备了钛酸钡-钡铁氧体核-壳粒子, 研究了沉淀反应温度、尿素/金属离子摩尔比值(R)和BaTiO₃浓度对核-壳粒子形貌和结构的影响, 探讨了钛酸钡-钡铁氧体核-壳粒子在焙烧时的形成过程及其磁性能. 采用透射电子显微镜(TEM)、X射线衍射(XRD)分析仪对钛酸钡-钡铁氧体前驱物核-壳粒子及钛酸钡-钡铁氧体核-壳粒子的形貌和结构进行了表征, 采用振动样品磁强计(VSM)研究了钛酸钡-钡铁氧体核-壳粒子的磁性能. 结果表明: 当沉淀反应温度为100 °C, R为180, BaTiO₃浓度为2.5 g·L^-1时, 金属离子沉淀完全, 得到的钛酸钡-钡铁氧体前驱物核-壳粒子包覆层均匀、完整、光滑, 厚度约为10 nm. 过高的温度和R值都会导致大量独立颗粒杂质的生成; 随着BaTiO₃浓度的增大, 包覆层厚度有减小的趋势. 当焙烧温度为900 °C时, 壳层中开始形成BaFe₁₂O₁₉相, 其形成过程为晶态的α-Fe₂O₃和BaCO₃首先生成中间相BaFe₂O₄, 然后由BaFe₂O₄和α-Fe₂O₃反应得到最终的BaFe₁₂O₁₉. 当焙烧温度为1000 °C时, 壳层完全转化为BaFe₁₂O₁₉相. 随着焙烧温度从900 °C升高到1000 °C, 所得BaTiO₃-BaFe₁₂O₁₉核-壳粒子的饱和磁化强度从16.5 A·m²·kg^-1增加到39.5 A·m²·kg^-1, 矫顽力从340 kA·m^-1略微降低到316 kA·m^-1.     

苯胺与吡咯共聚物空心球的自组装制备及性能

以碱性溶液为反应介质,苯胺和吡咯为单体,采用稀释聚合法制备苯胺-吡咯共聚物自组装空心微球.研究了搅拌条件、共聚单体摩尔比、聚合反应介质和聚合时间对共聚物形貌的影响.采用扫描电子显微镜、透射电子显微镜、红外光谱、广角X射线衍射、热重分析仪和四探针技术表征了共聚物的形貌、结构和性能.研究结果表明,聚合反应条件对共聚物的形貌有重大影响,通过调整聚合反应条件,可以实现共聚物形貌的有效调控.共聚单体总摩尔浓度为0.05 mol/L,氨水溶液作为反应介质,在静态条件下反应24 h可以得到尺寸均一、平均外直径为610～863 nm,壳厚144～162 nm的自组装共聚物空心微球.同时,研究了共聚物对银离子的吸附性能,结果表明共聚物对银离子有还原作用,吸附后共聚物表面有纳米银的生成.     

无规-类接枝共聚物自组装制备交联纳米微球

无规-类接枝共聚物(SFG)由大分子单体-己内酯改性丙烯酸酯(FA)、亲油性单体苯乙烯和甲基丙烯酸缩水甘油酯(GMA)共聚所得，SFG与聚苯乙烯在甲醇溶液中进行自组装，形成核壳结构纳米胶束，进一步对PGMA壳进行化学交联。最终得到具有核壳结构的纳米微球。动态激光光散射和透射电子显微镜表征结果显示SFG自组装形成了窄分布的纳米微球，微球粒径在100～200nm之间。     

化学沉淀-局部规整法制备棒状M型钡铁氧体的形成历程

以针状α-FeOOH为原料,采用化学沉淀-局部规整法制备了棒状BaFe₁₂O₁₉,通过TG/DTA、FTIR、XRD及SEM/EDS方法研究了BaFe₁₂O₁₉的形成历程。结果表明,前驱体为晶态BaCO₃包覆针状α-FeOOH复合物且呈现较好一维针状形貌,其长径比为16～17;前驱体焙烧过程为α-FeOOH首先脱去-OH生成中间相α-Fe₂O₃,尔后α-Fe₂O₃与BaCO₃反应生成另一中间相BaFe₂O₄,最后两中间相α-Fe₂O₃和BaFe₂O₄在高温(900 ℃以上)条件下反应生成目标产物BaFe₁₂O₁₉。固相反应引起的晶相转变过程中前驱体焙烧物的长径比随焙烧温度的增加逐渐减小,1 000℃焙烧产物长径比为7～8,存在极少量BaFe₂O₄和α-Fe₂O₃中间相,1 100 ℃焙烧产物长径比为2.5～7.0,为BaFe₁₂O₁₉纯相。     

棒状钡铁氧体的反相微乳法制备

A rodlike barium ferrite precursor with an average size of 0.72～19.6 μm and aspect ratio of 2.6～8.3 has been successfully prepared in an inverse microemulsion consisting of isooctane, cetanyl trimethyl ammonium bromide (CTAB), n-C₄H₉OH and water with ammonia and ammonium oxalate as precipitants. On sintering at 780(C, the rodlike precursor particles could be transformed into rodlike particles of barium ferrite(BaFe₁₂O₁₉) with the average size and aspect ratio of 0.69～18.2 μm and 2.3～5.8, respectively. The effect of volume ratio of aqueous phase to oleic phase, the starting concentrations of metal ions and the starting concentration ratios of metal ions to precipitants were investigated.     

纳米掺杂W型钡铁氧体的制备与性能研究

纳米钡铁氧体因为其优越的磁性能,被广泛应用在微波吸收材料等领域.近年来,对高效吸波材料开发和研究已经成为国内外学术界的热点.按照正交实验表的要求,采用溶胶-凝胶法制备了纳米掺杂W型钡铁氧体,采用TEM、XRD和VSM等检测手段进行了研究,得到了纳米掺杂W型钡铁氧体最佳的制备条件:pH值为7、柠檬酸物与金属离子的物质的量比为1∶1、焙烧温度为1100℃、焙烧时间为4.5 h.     

以胶体粒子为模板制备核壳纳米复合粒子

核壳纳米复合粒子具有许多不同于单组分胶体粒子的独特的光、电、磁、催化等物理与化学性质,是构筑新型功能复合材料的重要组元,在光子带隙材料、微波吸收材料、电磁流变液、催化剂和生物等领域有重要应用.本文从控制核壳复合粒子的微观结构及壳层均匀性与厚度的角度,详细评述了目前以胶体粒子为模板制备粒径从纳米到微米尺度的核壳复合粒子的方法.指出利用胶体粒子模板表面与壳层物质或其前驱物间的特殊相互作用(包括静电和化学相互作用),是完善现有制备方法和发展新方法来制备具有设定组成、结构和性能的核壳复合粒子的关键,同时也是将来的粒子表面纳米工程和获取有序的、先进纳米复合材料的主要方向。     

一种含有偶氮磺酸基与吡啶基的高分子氢键自组装及自组装超薄膜

静电自组装是指将带相反电荷的聚电解质，于水溶液中交替沉积在片基上，制备多层超薄膜的技术．由于它在水溶液进行，技术简单，无需专用设备，再加上静电力比范德华力强，因此静电自组装膜比传统的LB(Langmuir—Blodget)膜稳定，在近年来得到很大发展．现在自组装成膜驱动力已从最初的静电力扩展到氢键、电荷转移相互作用、疏水相互作用等；用于组装的组分也从聚电解质扩展到多官能团小分子、胶体粒子、无机纳米     

聚(4-偶氮磺酸苯乙烯-co-4-乙烯基吡啶)与本征态聚苯胺的氢键自组装及其光电转换性能

合成了一种新的共聚体——聚(4-偶氮磺酸苯乙烯-co-4-乙烯基吡啶), 它含有吡啶环, 能作为氢受体与本征态聚苯胺进行氢键自组装. 在紫外光照下, 组装膜通过偶氮磺酸基的光解, 形成稳定的共价交联结构, 在电解质水溶液中也不被破坏, 可用作光电转换膜, 并能在盐水溶液中直接测定它的光电流. 结果表明含有本征态聚苯胺的自组装膜是一种良好的光电转换材料.     

聚乳酸的层层自组装修饰及其内皮细胞相容性研究

通过胺解反应在生物降解聚(L-乳酸)表面引入带有正电荷的自由氨基,并通过静电吸引层层(Layer-by-layer,LBL)自组装技术将具有良好生物相容性的硫酸软骨素(CS)和细胞外基质成分型胶原组装到该PLLA材料表面.通过反应性荧光探针标记、紫外-可见吸收光谱以及荧光能量转移等测试技术跟踪并表征了自组装过程的进行.组装层的厚度开始随组装层数的增加而线性增加,而后增加变缓.内皮细胞的体外培养证明,表面组装CS和胶原(以胶原为最外层)以后,细胞的增殖率和细胞活性显著提高,材料的细胞相容性得到明显改善.细胞体现了充分铺展的多角形内皮细胞形貌,而且局部已融合形成了一单层内皮细胞层.     

Binding of a surfactant counterion to low-charge-density poly(acrylic acid) and poly(methacrylic acid)

The binding of a cationic surfactant, dodecylpyridinium (C12Py) chloride, with a low-charge-density poly (methacrylic acid) (PMA) was investigated in buffer solutions under the condition of constant pH. The binding isotherms with PMA consisted of two and three steps at a pH lower and higher than 3.2, respectively. Bindings in the first step were independent of pH and this step was considered to correspond to the solubilization of the hydrocarbon chains of C12Py into the nonpolar region of the compact form of PMA. This is the indication of the compact form from the binding isotherm. At pH higher than 3.2, the second step was discriminated and it depended on the pH. In the third step, a sharp rise in the degree of binding (β) was observed accompanying the solubilization of the precipitates of the PMA–C12Py complex. The binding with poly(acrylic acid) (PAA) and PMA in conventional unbuffered NaCl solutions was also examined and the pH profile of the solution during the binding process was determined. In the case of unbuffered NaCl solutions, the binding with PAA took place cooperatively at the critical association concentration (cac). The binding isotherm consisted of two steps and the pH decreased with the increase in β. The binding isotherm of PMA, on the other hand, consisted of three steps: the pH decreased slightly in the first step and considerably in the second step with the increase in β but it increased with β in the third step, exhibiting a pH minimum around 3.2. The binding in the first step coincided with that obtained in the buffered solutions. Linear relationships between β and the pH were found for both polymers. In the case of PMA, no cac was observed in both buffered and unbuffered NaCl solutions. Received: 24 January 2001 Accepted: 23 May 2001     

New insight in the role of modifying ligands in the sol-gel processing of metal alkoxide precursors: A possibility to approach new classes of materials

This paper summarizes recent literature data and presents new experimental data on the mechanisms of chemical modification, hydrolysis and polycondensation of the alkoxides and demonstrates possibilities to approach new classes of materials, exploiting these mechanisms. Low reactivity of silicon alkoxides is improved by either basic catalysis exploiting an S_N2 mechanism or acidic catalysis facilitating a proton-assisted S_N1 mechanism as well as by modification with chelating ligands. Metal alkoxides are much stronger Lewis bases compared to silicon alkoxides and the acidity of water is strong enough to achieve their rapid hydrolysis via proton-assisted S_N1 pathway even in the absence of additional catalysts. Introduction of the modifying chelating ligands is leading generally to increased charge distribution in the precursor molecules. Modifying chelating ligands are also appreciably smaller than the alkoxide ligands they replace. The modification with chelating ligands is thus facilitating the kinetics of hydrolysis and polycondensation. The size and shape of the primary particles formed in sol-gel treatment of metal alkoxides are defined not by kinetic factors in their hydrolysis and polycondensation but by the interactions on the phase boundary, which is in its turn directed by the ligand properties. The products of the fast hydrolysis and condensation sequence consist of micelles templated by self-assembly of ligands (mainly oxo-species). This concept provides explanations for commonly observed material properties and allows for the development of new strategies for the preparation of materials. We discuss the formation of inverted micelles, obtained by the appropriate choice of solvents, which allows for the formation of hollow spheres. The modifying β-diketonate ligands act as the surfactant and form an interface between the hollow sphere and the solvent. Retention of ligands inside the gel particles is possible only if ligands possessing both chelating and bridging properties are applied. Application of such ligands, for example, diethanolamine, permits to prepare new transition metal oxide based microporous membranes.     

Conductometric and microcalorimetric analysis of the alkaline-earth/alkali-metal ion exchange onto polyacrylic acid

The specificity of the exchange between divalent (Di²⁺ = Ca²⁺ or Ba²⁺) and monovalent (M⁺ = Li⁺, Na⁺ or K⁺) ions onto a polyacrylic chain is examined using conductometric and microcalorimetric techniques. Assuming the formation of a bidentate complex between the Di²⁺ and the carboxylate groups, the conductometric data give the exchange ratio (Di²⁺/M⁺) and the speciation of the acrylic groups. No significant difference is observed between the three alkali-metal ions for a given Di²⁺ ion. Comparisons between Ca²⁺ and Ba²⁺ show a stronger hydrophobicity of the former as it precipitates at a complexation ratio r = 0.33 versus r = 0.45 for the Ba²⁺ salt. Microcalorimetric data show that all Di²⁺/M⁺ exchange energies are positive and depend significantly on the type of cations. The largest displacement energy (the more positive) is found for the binding of Ca²⁺ with sodium polyacrylate (8.13 kJ · mol⁻¹) and the smallest for Ba²⁺ with lithium polyacrylate (1.88 kJ · mol⁻¹). The interpretation of the data leads to the conclusion that specificity of the Di²⁺ binding originates in the dehydration phenomenon and specificity between the three alkali-metal ions is due to the decrease in the electrostatic bond strength with an increase in the ionic radii. The Di²⁺/M⁺ exchange is entropically driven. Received: 28 January 1999 Accepted in revised form: 7 April 1999     

A Non-isocyanate Route to Poly(ester urethane) with High Molecular Weight: Synthesis and Effect of Chemical Structures of Polyester-diol

A series of non-isocyanate linear high molecular weight poly(ester urethane)s(PETUs)were prepared through an environmentallyfriendly route based on dimethyl carbonate,1,6-hexanediol and 1,6-hexanediamine.In this route,the polyurethane diol was first prepared by the reaction between bis-1,6-hexamethylencarbamate(BHC)and 1,6-hexanediol.A series of polyester soft segments of polyurethane have been synthesized from the polycondensation of adipic acid and different diols,including butanediol,hexanediol,octanediol and decanediol.The subsequent polycondensation of polyurethane diol and polyester diol led to linear PETUs.The resultant polymers were characterized by GPC,FTIR,¹H-NMR,¹³C-NMR,DSC,WAXD,TGA and tensile test.The results indicated that PETUs possess weight-average molecular weights higher than 1×10⁵ and the tensile strength as high as 10 MPa.The thermal properties,crystallization behavior,microphase separation behavior and morphology were studied by DSC and AFM,and the results indicated that the degree of phase separation was affected by two factors,the crystallization and hydrogen bonding interaction between soft segment and hard segment.     

利用室温固态反应制备球霰石型CaCO3粒子

合成形态、大小及结构可人为调控的无机材料是现代材料科学的重要研究方向[1]. 借助于各类有机添加剂及模板剂的调控作用, 可利用溶液合成方法制备出形貌与结构受到有效调控的无机粒子[2,3]. 室温固态化学反应已被成功地应用于多种无机纳米粒子[4]及纳米线[5]的合成, 并显示出高效、节能、无污染和操作简便等优点, 因而在材料合成领域具有应用前景[6].     

Chemical recycling of poly(lactic acid)-based polymer blends using environmentally benign catalysts

Typical poly(l-lactic acid) (PLLA)-based polymer blends, PLLA/polyethylene (PE) and PLLA/poly(butylene succinate) (PBS), were degraded into each repolymerizable oligomer using environmentally benign catalysts, clay catalysts and enzymes, with the objective of developing a selective chemical recycling process. Two routes to selective chemical recycling of PLLA/PE blend were tested. One is the direct separation of PLLA and PE first by their different solubilities in toluene, followed by the chemical recycling of PLLA using montmorillonite K5 (MK5). The other is the selective degradation of PLLA in the PLLA/PE blend by MK5 in a toluene solution at 100 °C for 1 h forming the LA oligomer with a molecular weight of M_n = 200-300 g/mol, which is the best M_n for repolymerization. Thus regenerated PLLA had a M_w of greater than 100,000 g/mol. The PE remained unchanged and was quantitatively recovered by the reprecipitation method for material recycling. In a similar procedure, chemical recycling of PLLA/PBS blend was also carried out and compared by two routes. One is the direct separation of PLLA and PBS by solubility in toluene. The other route is the sequential degradation of PLLA/PBS blend using a lipase first to degrade PBS into cyclic oligomer, which was then repolymerized to produce a PBS. Next, PLLA was degraded into repolymerizable LA oligomer by MK5. The former procedure was carried out using a single solvent; however, the latter required mixed solvents, which decreased the efficient recycling use of solvents.     

Recent progress in MXene and graphene based nanocomposites for microwave absorption and electromagnetic interference shielding

There is widespread use of telecommunication and microwave technology in modern society, and raised the electromagnetic interference (EMI) issue to alarming situation due to apprehensive demand and growth of 5G technology undesirably disturbing the human health. The two dimensional (2D) materials including graphene and MXenes are already been used for variety of electronic devices due to their exceptional electrical, mechanical, optical, chemical, and thermal properties. MXene is composed of metal carbides, in which mainly metals are the building blocks for dielectrics, semiconductors, or semimetals. However, the strong interfaces with electromagnetic waves (EM) are variable from terahertz (THz) to gigahertz (GHz) frequency levels and are widely used in EMI and Microwave absorption (MA) for mobile networks and communication technologies. The use of different organic materials with metal, organic, inorganic fillers, polymers nanocomposite and MXene as a novel material has been studied to address the recent advancement and challenges in the microwave absorption mechanism of 2D materials and their nanocomposites. In this concern, various techniques and materials has been reported for the improvement of shielding effectiveness (SE), and theoretical aspects of EMI shielding performance, as well stability of 2D materials particularly MXene, graphene and its nanocomposites. Consequently, various materials including polymers, conducting polymers, and metal–organic frameworks (MOF) have also been discussed by introducing various strategies for improved MA and control of EMI shieling. Here in this comprehensive review, we summarized the recent developments on material synthesis and fabrication of MXene based nanocomposites for EMI shielding and MA. This research work is a comprehensive review majorly focuses on the fundamentals of EMI/MA.  The recent developments and challenges of the MXene and graphene based various structures with different polymeric composites are described in a broader perspective.