Tapered fiber amplifier with high gain and output power

We present a high-power ytterbium fiber amplifier based on active tapered double-clad fiber (T-DCF) and capable of high single-pass gain. The T-DCF power amplifier seeded with a 320 mW narrow-band signal generates up to 110 W of average output power corresponding to more than 25 dB gain. The amplifier exhibits near-diffraction-limited beam quality (M ² = 1.06) at the highest output power, which was limited by the available pump power. With a broadband seed source, the amplifier produced a gain of nearly 40 dB obtained for low-signal limit of the seed. The high output power combined with high gain is achieved owing to amplified spontaneous emission (ASE) filtering and increased stimulated Brillouin scattering (SBS) threshold inherent to the axially non-uniform geometry. The amplifier operates efficiently with a wide range of input seed powers thus providing the basis for one-stage tapered amplifier which combines the functions of preamplifier and power amplifier and can be a competitive alternative to multi-stage design.     

High gain L-band erbium-doped fiber amplifier with two-stage double-pass configuration

An experiment on gain enhancement in the long wavelength band erbium-doped fiber amplifier (L-band EDFA) is demonstrated using dual forward pumping scheme in double-pass system. Compared to a single-stage single-pass scheme, the small signal gain for 1580 nm signal can be improved by 13.5 dB. However, a noise figure penalty of 2.9 dB was obtained due to the backward C-band ASE from second stage and the already amplified signal from the first pass that extracting energy from the forward C-band ASE. The maximum gain improvement of 13.7 dB was obtained at a signal wavelength of 1588 nm while signal and total pump powers were fixed at -30 dBm and 92 mW, respectively.     

Double-pass ytterbium-doped fiber amplifier with high gain coefficient and low noise figure

We have proposed and demonstrated a double-pass ytterbium-doped fiber amplifier using an optical circulator and a fiber Bragg grating as reflector. When the signal has passed through the ytterbium-doped fiber once, it reflects off a 0.2-nm passive fiber Bragg grating filter. This reduces amplified spontaneous emission (ASE) noise from the first pass. The input signal light is amplified both forward and backward through ytterbium-doped fiber. With this double-pass configuration, 1053.15-nm unsaturated signal gain of 28 dB, gain coefficient of 1.1 dB/mW, and noise figure of less than 4 dB are achieved at 977-nm pump power of 68 mW. It is also found that this double-pass configure provides enhancing gain coefficient and improving noise figure by comparison with single-pass configuration.     

Er3+,Yb3+共掺磷酸盐玻璃沟道波导放大器

在自行研制的Er3 ，Yb3 共掺磷酸盐玻璃基质上用离子交换方法制作出沟导光波导放大器。在110mW的抽运功率下(抽运光波长为980nm)，在1．8cm长的器件上获得了3．8dB的小信号(信号光波长为1．55μm)增益，单位长度上的增益为2．1dB／cm。     

A global design of an erbium-doped fiber and an erbium-doped fiber amplifier

A global design of an erbium-doped fiber and an open-loop erbium-doped fiber amplifier (EDFA) in a steady-state operation is discussed by applying genetic algorithms. Taking a signal gain and a bandwidth as objective functions, 7 parameters of the EDFA (erbium concentration, core radius, erbium-doped radius, refractive index difference, fiber length, pumping wavelength and signal power) are optimized by solving optical propagation equations, assuming a homogenous two-level active medium and a single-mode propagation. There is evidence to show that the 1480 nm pump utilized in usual EDFAs is not an optimal choice, which should be chosen around 1460 nm. The optimal core radius ranges 0.465–0.548 μm on pumping power 50–200 mW. Under different design objects and with different pumping powers, however, there are different optimal Er-doped concentrations, reflective index differences and fiber lengths. As a single fiber EDFA, 35 dB signal gain or 35 nm bandwidth is obtained with the 7 optimal parameters, 100 mW pumping power and 0.001 mW input signal power.     

Er-Al-codoped silicate planar light waveguide-type amplifier fabricated by radio-frequency sputtering

A planar light waveguide-type optical amplifier was designed and fabricated. A core layer of Er-Al-codoped SiO>(2) glass was deposited onto a silica cladding layer by rf sputtering. In the Er-doped core layer the average Er and Al concentrations were 0.77 and 11.37 wt.%, respectively. We achieved 5 dB of gain with 20 mW of 980-nm pump power by using -20 dBm of 1546-nm input signal power.     

Effects of an auxiliary pump on the performance of TDFA

An efficient fluoride-based thulium-doped fiber amplifier (TDFA) is theoretically demonstrated using a dual pumping scheme. Differential equations are solved directly in the theoretical analysis. An auxiliary pump at 1560 nm is used for ground-state absorption to enhance the excited-state absorption provided by the main pump of 1050 nm and, thus, to improve the gain and noise figure of the TDFA. A gain improvement of more than 10 dB is obtained at the 1470-nm region with the use of a 1560-nm pump at 20 mW. A small signal gain as high as 30 dB is obtained at this region with 100 mW of a 1050-nm pump and 20 mW of a 1560-nm pump using a 20-m of thulium-doped fiber. The corresponding noise figure is obtained at lower than 5 dB.     

An effective numerical method for gain profile optimizations of multi pumped fiber Raman amplifiers

In this paper, we have solved propagation equations of multi-pump fiber Raman amplifier using Runge–Kutta (RK 4th order) numerical method and pump power evolutions along with the fiber length. They are used to calculate the net gain and gain ripple by varying the input signals powers for different fiber lengths. The pump powers are optimized by genetic algorithm and resulting net gain and gain ripple are reported graphically as well as in tabular form. The optimum minimum gain ripple is 0.26 dB for 1 mW input signal powers for 50 km fiber length. By increasing the fiber length gain ripple increases to 0.5 dB for 0.1 mW input signal power. In comparison to other methods reported in the literature, our method is simple to implement and efficient for numerical design of Raman amplification in optical communication systems.     

56 dB Gain EYDFA with improved noise figure with dual-stage partial double pass configuration

An efficient erbium/ytterbium co-doped fiber amplifier (EYDFA) is demonstrated by using a dual-stage partial double pass structure with a band pass filter (BPF). The amplifier achieves the maximum small signal gain of 56 dB and the corresponding noise figure of 4.66 dB at 1536 nm with an input signal power and total pump power of ?50 dBm and 140 mW, respectively. Compared with a conventional single-stage amplifier, the maximum gain enhancement of 16.99 dB is obtained at 1544 nm with the corresponding noise figure is improved by 2 dB. The proposed amplifier structure only uses a single pump source with a partial double pass scheme to provide a high gain and dual-stage structure to provide the low noise figure.     

High-gain and low-noise-figure erbium-doped fiber amplifier employing dual stage quadruple pass technique

A high-gain and low-noise-figure (NF) erbium-doped fiber amplifier (EDFA) was demonstrated utilizing a new technique called the dual-stage quadruple pass (DSQP) with filters. An efficient amplification occurs at the signal wavelength of 1550 nm when it travels along the DSQP amplifier. The highest gain of 62.56 dB with a low noise figure of 3.98 dB was achieved for an input signal power of −50 dBm and pump powers of 10 and 165mW in the second and first stage amplifiers respectively.     

Gain and noise figure improvements in double-pass S-band EDFA

Double-pass short-wavelength band erbium-doped fiber amplifier (S-band EDFA) with enhanced gain and noise figure characteristics is demonstrated. It uses a broadband fiber Bragg grating (FBG) operating in conventional-band (C-band) region to reduce the C-band amplified spontaneous emission (ASE) in the amplifier system and thus increases the population inversion in the S-band region. The small signal gain is increased by about 2.7 dB for 1500 nm signal at pump power of 103 mW, compared with that of the conventional double-pass amplifier without the FBG. The corresponding noise figure is also improved by 0.5 dB.     

基于KMnF_3∶Yb~(3+),Er~(3+)纳米晶的红光聚合物平面光波导放大器

制作了基于KMnF_3∶Yb~(3+),Er~(3+)纳米晶材料的工作波长655 nm的聚合物平面光波导放大器。材料的吸收光谱表明,KMnF_3∶Yb~(3+),Er~(3+)纳米晶在980 nm附近有很强的吸收。在980 nm激光的激发下,由于Er~(3+)和Mn2+能级之间的能量传递,KMnF_3∶Yb~(3+),Er~(3+)纳米晶产生了很强的红色上转换发光。根据KMnF_3∶Yb~(3+),Er~(3+)纳米粒子的发光特性,制备了KMnF_3∶Yb~(3+),Er~(3+)NCs-PMMA复合材料,用其作为芯层设计了掩埋形结构光波导放大器,利用传统的半导体工艺完成器件制备。器件测试结果表明,当655 nm信号光功率为0.1 m W、980 nm泵浦功率为260 m W时,器件获得了2.7 d B的相对增益。     

覆盖可见光波长的掺Er光纤飞秒光学频率梳

飞秒光学频率梳波长覆盖范围向可见光波长扩展对于碘稳频激光的绝对频率测量以及光钟研究中钟激光的绝对频率测量都具有十分重要的意义. 本文在自行研制掺Er光纤飞秒光学频率梳的基础上, 采用放大-倍频-扩谱的方案, 实现了激光输出波长向可见光波长的扩展. 掺Er光纤飞秒光学频率梳输出的一部分光激光脉冲, 功率约为8 mW, 首先经掺Er光纤放大器将功率提高到531 mW, 此后利用MgO: PPLN晶体倍频, 倍频后激光的功率为170 mW, 倍频效率为32%, 脉冲宽度为85 fs. 倍频后的激光通过光子晶体光纤进行光谱展宽. 通过优化入射光偏振状态可以实现波长覆盖500-1000 nm, 输出功率为85 mW, 耦合效率为50%. 采用小型化碘稳频532 nm Nd: YAG激光器输出激光与光学频率梳光谱展宽后的激光进行拍频可以获得30 dB的拍频信号. 覆盖可见光波长的掺Er光纤飞秒光学频率梳为可见光范围内激光的绝对频率测量提供了技术手段.     

低噪声、高增益的L -band EDFA的实验研究

针对传统的L-band EDFA的工作效率低,提出了一种基于单根光纤光栅、泵浦分配、两段级联的EDFA的新结构,其中的光纤光栅用来反射无用的后向C-band ASE.系统地研究了泵浦比例和光纤光栅波长对增益噪声指数的影响关系.最后经实验验证,得到了低噪声、高增益的L-band的EDFA.其在输入信号光（1570 nm）功率为-30 dBm及泵浦功率为70 mW时,增益为22.26 dB,增益噪声指数为4.96 dB.     

高功率宽带射频调制连续激光源

射频强度调制激光作为激光雷达系统的载波可以有效提高系统的抗干扰和抗散射能力,高功率宽带射频强度调制光源是实现高分辨率远距离探测的关键.本文采用在Nd:YAG激光器的耦合腔中插入一对四分之一波片的方法实现了频差调谐范围为30 MHz—1.5 GHz的双频激光输出,结合光纤振荡功率放大技术,将双频信号光功率放大为50 W.耦合腔双频种子源具有良好的功率和频率稳定性,输出功率为9.5 mW时,功率标准差为0.145 mW,稳定性为1.52%,输出双频激光的频差为250 MHz时,拍频的标准差为1.6144 MHz.种子光进行三级光纤功率放大,得到50 W双频激光输出.放大后的双频激光功率波动范围小于0.1 W,双频拍频的标准差为1.777 MHz,很好地保持了放大之前的功率稳定性和双频频差稳定性.     

基于高非线性光子晶体光纤Sagnac环形镜的全光开关

设计了一种新颖的、低开关功率的全光开关. 将高非线性光子晶体光纤和双向抽运掺饵光纤放大器引入Sagnac环形镜内，破坏了环形镜的对称性，利用交叉相位调制作用使反向传输的两路信号光产生非线性相移，从而实现开关效应. 理论分析表明：开关功率与放大器的增益倍数和光子晶体光纤非线性系数的积成反比，在实验中所得开关功率约40 mW，消光比约为15.9 dB，并且信号光透过率随脉冲控制光峰值功率呈余弦变化，实验结果与理论分析相吻合. 关键词： 全光开关 高非线性光子晶体光纤 环形镜 交叉相位调制     

18 W single-stage single-frequency acoustically tailored Raman fiber amplifier

A single-mode polarization-maintaining fiber doped to increase the Raman gain while suppressing stimulated Brillouin scattering (SBS) was utilized in a single-stage counter-pumped Raman fiber amplifier. The SBS suppression was achieved through the acoustic tailoring of the core. A pump probe experiment was conducted to characterize the Brillouin gain and indicated the existence of multiple Brillouin peaks. When the amplifier was seeded with approximately 15 mW of 1178 nm light, 11.5 W of cw output power was obtained with a linewidth ≤2 MHz. The application of a thermal gradient to further mitigate the SBS process increased the output power to 18 W, thus providing a net amplifier gain >30 dB.     

包层泵浦fs光纤放大器的实验研究

 在实验上对双包层光纤放大器进行了研究。采用新型内包层为六边形的铒镱共掺双包层光纤作为放大介质,用带尾纤的半导体激光器进行泵浦,对fs光脉冲进行放大。当用2.5 W的入纤功率泵浦50 cm长的双包层铒镱光纤时,把平均功率为10.8 mW、重复频率20.84 MHz的激光放大到176 mW,增益为12.2 dB,相应的单脉冲能量为8.1 nJ,放大后脉冲宽度为480 fs,峰值功率为16 kW。     

37.2 dB small-signal gain from Er/Yb Co-doped fiber amplifier with 20 mW pump power

An efficient erbium–ytterbium-doped fiber amplifier (EYDFA) is demonstrated by forward and backward pumping a 3 m erbium/ytterbium co-doped fibers (EYDF) in single- and double-pass configurations using a 20 mW pump. At the input signal wavelength of 1536 nm, the forward- and backward-pumped double-pass amplifiers achieved a maximum low-signal gain of 37.2 and 28.6 dB and a corresponding noise figure of 5.4 and 10.8 dB, respectively. Whereas, the forward- and backward-pumped single-pass amplifiers (at the same wavelength) achieved a maximum low-signal gain of 20.0 and 22.2 dB and a corresponding noise figure of 4.6 and 10.3 dB, respectively. The double-pass design offers an economical solution to high-efficiency and high-gain optical amplifiers.     

Amplification effect on SBS and Rayleigh scattering in the backward pumped distributed fiber Raman amplifier

The amplification effect on stimulated Brillouin scattering （SBS） and Rayleigh scattering in the backward pumped G652 fiber Raman amplifier （FRA） is studied. The pump source is a 1427.2-nm fiber Raman laser whose power is tunable between 0 - 1200 mW, and the signal source is a tunable narrow spectral bandwidth （〈 10 MHz） external cavity laser （ECL）. The Rayleigh scattering lines are amplified by the FRA and Stokes SBS lines are amplified by the FRA and the fiber Brillouin amplifier. The total gain of SBS lines is the production of the gain of Raman amplifier and that of Brillouin amplifier. In experiment, the SBS gain is about 42 dB and the saturation gain of 25-km G652 backward FRA is about 25 dB, so the gain of fiber Brillouin amplifier is about 17 dB.