铂/聚邻甲基苯胺/碳材料掺杂碳糊电极对甲醇的催化氧化

以石墨和液体石蜡油为主要原料,分别制备了掺杂不同量多壁碳纳米管(MWCNT)、石墨烯(GRA)、电容活性炭(YEC)和电池活性炭(YBC)的多种碳糊底电极Y-CPE(Y代表各种掺杂碳材料,CPE代表纯碳糊电极).采用恒电位法在-0.10 V(vs.Ag/Ag Cl)电位下将铂电沉积到这些电极上.结果表明,当电池碳的含量为14%时,Pt/YBC-CPE(14%)复合电极对甲醇具有最好的电催化氧化活性.采用恒电位方法在0.85 V(vs.Ag/Ag Cl)电位下将聚邻甲基苯胺(POT)电聚合沉积到纯碳糊电极CPE和含有电池碳的YBC-CPE(14%)电极上,得到复合电极POT/CPE和POT/YBC-CPE(14%),再通过恒电位方法将铂电沉积到这2个复合电极上.扫描电镜(SEM)观察结果表明,在Pt/CPE,Pt/YBC-CPE(14%),Pt/POT(6.5 mC)/CPE和Pt/POT(6.5 mC)/YBC-CPE(14%)4个复合电极中,在Pt/POT/YBC-CPE(14%)复合电极上的铂粒子的尺寸最小,并且Pt/POT(6.5 mC)/YBC-CPE(14%)复合电极电催化氧化甲醇活性最高.在POT(6.5 mC)/CPE和POT(6.5 mC)/YBC-CPE(14%)上Pt纳米颗粒的电沉积过程是一个近似的3D成核过程.研究还发现,复合电极Pt/POT/CPE和Pt/POT/YBC-CPE电催化氧化甲醇的活性随POT膜厚度的增加先增大后减少,存在一个最佳的膜厚度.     

铂-氧化铈/聚苯胺/聚砜复合膜电极的制备及对甲醇的电催化氧化

采用电化学聚合法制备了掺杂CeO2纳米粒子的聚苯胺(PAN)/聚砜(PSF)复合膜电极,在其上电沉积铂粒子,制得了铂-氧化铈/聚苯胺/聚砜的复合膜修饰电极。 复合膜的形貌和化学组分通过冷场发射扫描电子显微镜（Cold FE-SEM）和能量散射X射线谱（EDS）进行了表征,用循环伏安法和电化学交流阻抗法考察了复合膜电极对甲醇的电催化氧化性能。 结果表明,复合膜的双层多孔结构使铂粒子与CeO2粒子在复合膜内层的多孔聚苯胺上均匀沉积,粒子平均尺寸约为80 nm;CeO2为铂质量的7%时,铂-氧化铈/聚苯胺/聚砜复合膜修饰电极对甲醇有很好的电催化氧化性能和高的稳定性。     

一步法制备纳米铂/石墨烯及电催化甲醇的交流阻抗和扩散系数测定

采用绿色还原剂抗坏血酸,一步法制备纳米铂/石墨烯。对其进行X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)形貌结构表征,铂纳米粒子均匀分散于纳米石墨烯片层褶皱间,有效减少了团聚现象。运用循环伏安法(CV)和计时电流法(CA)研究纳米铂/石墨烯对甲醇电催化氧化活性和稳定性,通过交流阻抗(EIS)定量测定,发现铂/石墨烯比铂具有更优异的电荷传输性能,电荷转移阻抗下降了34.8%。计时电量法(CC)测定得到甲醇在铂/石墨烯电极的表面扩散系数为1.42×10~(-9) cm~2·s~(-1)。与铂纳米粒子相比,纳米铂/石墨烯对甲醇电催化氧化具有更高的活性和稳定性,显著提高电极催化活性表面积和电荷传输及转移性能。     

多层聚吡咯-铂复合膜电极的甲醇电催化氧化

应用循环伏安法电沉积多层聚吡咯-铂复合膜电极,研究该电极的甲醇电催化氧化性能.循环伏安和计时安培法测试表明,该复合膜电极具有更好的甲醇电催化活性和抗毒性.铂量增加,电极反应控制步骤将由CO氧化转化为甲醇的吸附脱氢.     

甲醇在铂微粒修饰的聚硫堇电极上的电催化氧化

利用电化学循环伏安和现场ＦＴＩＲ反射光谱等技术研究了甲醇在铂微粒修饰的聚硫堇电极上的电催化氧化。结果表明，循环伏安法制备的铂微粒均匀分散于聚合物膜上，其粒径大小约为３０－１３０ｎｍ；复合修饰电极对甲醇电化学氧化呈现了较高的催化活性，其催化活性的大小依赖于Ｐｔ载量。现场ＦＴＩＲ光谱实验揭示了线性吸附的ＣＯ物种是甲醇在复合电极上氧化的唯一中间体，这种吸附的ＣＯ物种在复合修饰电极上更容易被氧化为最终产物     

碳化钨与蒙脱石纳米复合材料的制备与电催化活性

具有类铂催化性能的碳化钨(WC)催化材料是当前研究的热点与难点. 本文以六氯化钨为钨源, 用剥离后的蒙脱石片层为载体, 将化学浸渍法与原位还原碳化法技术相结合制备了碳化钨与蒙脱石纳米复合材料; 复合材料由碳化钨、碳化二钨(W₂C)和蒙脱石(MMT)组成, 碳化钨呈颗粒状分散或呈层状负载于MMT外表面; 样品的晶相组成与其还原碳化时间有关; 样品的微结构特征与前驱体中钨与蒙脱石的比例有关. 采用三电极体系和循环伏安法测试了样品在酸性溶液中对甲醇的电催化氧化性能, 结果表明, 碳化钨与蒙脱石复合之后对甲醇的电催化性能明显提升, 并具有类铂电催化活性; 当钨与蒙脱石质量比为4 的前驱体经5 h 还原碳化后, 样品中WC占绝对主导, WC和W₂C的质量分数分别为82%和18%, 两者的比值为4.556, 且在MMT外表面形成均匀的负载层. 此时样品的电催化活性最高. 这为制备具有类铂催化活性的高性能碳化钨催化材料奠定了坚实基础.     

甲醇在铂修饰的氧化钛电极上电催化氧化行为的研究

运用电化学方法评价了电化学阴极还原-阳极氧化两步法制得的以钛为基体的铂修饰的钛氧化物(Pt-TiO_x/Ti)电极对甲醇电催化氧化的性能,结果表明,制得的修饰电极对甲醇氧化呈现了很高的电催化活性和好的稳定性.通过X光电子能谱(XPS)、扫描隧道显微镜(STM)和现场傅立叶变换红外(FTIR)反射光谱等技术,发现修饰电极对甲醇氧化具有高的电催化性能,可归属于纳米级Pt粒子在TiO_x中的高度分散及由于Pt和TiO_x的相互作用,使电极表面对甲醇氧化中间产物CO的吸附量大大降低.     

FeTSPc对Pt电极对氧还原的电催化性能和耐甲醇性能的影响

为了解决直接甲醇燃料电池(DMFC)中“甲醇渗透”的问题, 用大环化合物四磺酸基酞菁铁(FeTSPc)对光滑铂(Pt)电极进行修饰, 发现FeTSPc修饰的Pt电极(Pt-FeTSPc)和Pt电极对氧还原的电催化活性相近, 而Pt-FeTSPc电极对甲醇氧化的电催化活性比Pt电极下降30.9%, 表明Pt-FeTSPc电极有较好的耐甲醇能力.     

分子印刷技术铂微粒修饰电极及甲醇的电催化氧化

利用分子印刷技术(Molecular Imprinting Technology，MIT)，将铂微粒沉积到谷胱甘肽自组装膜的针孔上，并用循环伏安法研究了甲醇在该电极上的电催化氧化行为。实验结果表明，该电极对甲醇电化学氧化呈现出较高的催化活性，活性高低与载铂量、溶液pH值及电极表面铂微粒所处的微环境有关。     

一种提高铂电催化氧化甲酸性能的简单方法

在离子液体1-乙基咪唑三氟乙酸盐(HElmTfa)中,采用循环伏安法在铂电极表面修饰聚吡咯(PPY),制得PPy-HEImTfa/Pt,并研究了其对甲酸的电催化氧化性能.与相同条件下的铂基底电极相比,PPy-HEImTfa/Pt对甲酸的电催化氧化性能有很大的提高.原位红外光谱表明,PPy-HElmTfa能降低中间体CO等对铂电极的毒化作用,促进甲酸直接氧化生成CO_2.     

Composite electrodes consisting Pt nano-particles and poly (aminophenols) film on pre-treated aluminum substrate as electrocatalysts for methanol oxidation

Electrochemically platinum plated aluminum (Al/Pt) was used as an electrode substrate for the electropolymerization of aminophenols and fabrication of composite electrodes based on platinum nano-particles. The poly(o-aminophenol) (PoAP), poly(m-aminophenol) (PmAP), and poly(p-aminophenol) (PpAP) were synthesized on the Al/Pt electrode, and further modification was performed by deposition of platinum nano-particles onto polymer matrixes. The electrochemical and morphological characteristic of the composed electrodes were carried out by cyclic voltammetry and scanning electron microscopy, respectively. The electrocatalytic oxidation of methanol on the composite electrodes was studied by cyclic voltammetry in 0.1 M sulfuric acid as supporting electrolyte. It was found that the Al/Pt/PoAP electrode incorporated Pt nano-particles (Al/Pt/PoAP/Pt) exhibits a higher electrocatalytic activity for the oxidation of methanol than the Al/Pt/PmAP/Pt and Al/Pt/PpAP/Pt electrodes. On the other hand, a higher catalytic current for methanol oxidation was found on the Al/Pt/PoAP/Pt electrode in comparison to bulk Pt and Al–Pt (Al with 0.2 mg cm⁻² of Pt particles) electrodes. The effects of various parameters such as thickness of the polymer film, concentration of the monomer, Pt loading method and the Pt amounts, concentration of the methanol, and the medium temperature were studied on the electrooxidation of methanol. The long-term stability of the modified electrode has also been investigated.     

Platinum Nanoparticles/Poly(isoleucine) Modified Glassy Carbon Electrode for the Simultaneous Determination of Hydroquinone and Catechol

A new electrochemical sensor based on Poly(Isoleucine) modified glassy carbon electrode decorated with platinum nanoparticles (Pt/Poly(Isoleucine)/GCE) was developed for sensitive individual and simultaneous determination of hydroquinone (HQ) and catechol (CC). Scanning electron microscopy (SEM), Electrochemical impedance spectroscopy (EIS), Cyclic voltammetry (CV) and Differential pulse voltammetry (DPV) were performed in order to characterize the Pt/Poly(Isoleucine)/GCE nanocomposite. For simultaneous determination of HQ and CC, Pt/Poly(Isoleucine)/GCE showed wide linear range between the 0.01–100.0 μM. The detection limits were 0.006 μM for HQ and 0.005 μM for CC. The Pt/Poly(Isoleucine)/GC electrode exhibited good sensitivity and reliability in the simultaneous electroanalysis of two isomers in PBS of pH 7.5. The modified electrode was used to detect the isomers in naturel samples.     

聚(2,5-二氧基苯胺)膜修饰电极的电化学及催化性质

二甲氧基苯胺;电沉积;氧化;化学修饰电极;聚(2;5-二氧基苯胺)膜修饰电极的电化学及催化性质     

铂微粒修饰聚2，5－二甲氧基苯胺电极对甲醇的电催化作用

将以铂微粒修饰玻碳电极（ＧＣ）为基体的聚２，５－二甲氧基苯胺膜（ＰＤＭＡ）形成修饰电极（Ｐｔ／ＰＤＭＡ／ＧＣ）．循环伏安实验表明，Ｐｔ／ＰＤＭＡ／ＧＣ电极对甲醇氧化比分散于玻碳电极上的铂催化活性更大。讨论了ＰＤＭＡ膜厚度、铂微粒含量及甲醇浓度对催化活性的影响。这种电极在酸性甲醇溶液中具有良好的稳定性。     

Preparation of Platinum Implanted Glassy Carbon Electrode and Electro-oxidation of Formic Acid and Formaldehyde

Electrocatalytic oxidation of small organic molecules has attracted considerable at-tentionin system of fuel celll-4. In this research field, Parsons4 pointed out that the electrodeswhich were prepared from non-noble substrates modified by excellent dispersal noblemetal particles and which still exhibited better catalytic activity should be studied. Ionimplantation is a technique with unique advantage and has been used in manyelectrochemical research fieldss'6. The present study is an at-tempt…     

Electrocatalytic oxidation of methanol onto platinum particles decorated nanostructured poly (1,5-diaminonaphthalene) film

In this work, platinum particles decorated nanostructured poly (1,5-diaminonaphthalene) modified glassy carbon electrode (Pt/Nano-PDAN/MGCE) is prepared. The composite catalysts are characterized by scanning electron microscopy, energy dispersive spectroscopy, and electrochemical methods. The electrochemical methanol oxidation reaction is studied at the surface of this modified electrode. At same Pt loading, the Pt/Nano-PDAN/MGCE can act as higher efficient catalyst for methanol oxidation than that Pt/MGCE. Then, the influence of some parameters such as potential scan rates, switching potential, and methanol concentration on its oxidation as well as long-term stability of the modified electrode have studied by electrochemical methods. Also, ability of the modified electrode toward electrocatalytic oxidation of formaldehyde as an intermediate in methanol oxidation has been investigated.     

甲醇在欠电位沉积Sn/Pt电极上催化氧化

在欠电位沉积（upd）锡修饰的铂电极（upd-Sn/Pt）上,对甲醇电化学催化氧化过程进行了研究.发现当Pt表面upd-Sn的覆盖率在20％附近时,对甲醇的催化氧化的增强作用最为明显；在电位低于0.35 V （vs RHE）时,甲醇在Pt与upd-Sn/Pt电极上氧化只进行到脱氢生成CO的步骤;在0.35 V以后,表面Sn－OH形成,反应Sn－OH＋COads=Sn＋CO2＋H＋＋e有利于表面CO的去除;而Pt电极上,只有0.6 V以后,才有反应Pt－OH＋COads=Pt＋CO2＋H＋＋e发生.因此,Sn的存在有利于甲醇在较低的电位下氧化; Pt电极上CH3OH脱氢并释放出电子的过程是一个快速的过程,表面CO的去除是甲醇氧化过程的控制步骤;甲醇氧化产生的表面吸附态CO 以线式吸附为主,少量的桥式吸附态CO在反应初期即达到吸附饱和; Pt表面上upd-Sn表现的催化增强作用,在光亮铂电极和在高分散铂黑电极上是一致的.     

Effect of the iridium oxide thin film on the electrochemical activity of platinum nanoparticles

The influence of the iridium oxide thin film on the electrocatalytic properties of platinum nanoparticles was investigated using the electro-oxidation of methanol and CO as a probe. The presence of the IrO(2) thin film leads to the homogeneous dispersion of Pt nanoparticles. For comparison, polycrystalline platinum and Pt nanoparticles dispersed on a Ti substrate in the absence of an IrO(2) layer (Ti/Pt) were also investigated in this study. Inverted and enhanced CO bipolar peaks were observed using an in situ electrochemical Fourier transform infrared technique during the methanol oxidation on the Pt nanoparticles dispersed on a Ti substrate. Electrochemical impedance studies showed that the charge transfer resistance was significantly lower for the Ti/IrO(2)/Pt electrode compared with that of the massive Pt and Ti/Pt nanoparticles. The presence of the IrO(2) thin film not only greatly increases the active surface area but also promotes CO oxidation at a much lower electrode potential, thus, significantly enhancing the electrocatalytic activity of Pt nanoparticles toward methanol electro-oxidation.     

High dispersion and electrocatalytic properties of platinum nanoparticles on graphitic carbon nanofibers (GCNFs)

Highly dispersed platinum nanoparticles were electrodeposited on graphitic carbon nanofibers (GCNFs) by cyclic voltammetry (CV) in 7.7 mM H2PtCl6+0.5 M HCl aqueous solutions. The graphitic carbon nanofibers (GCNFs) used in this paper were grown directly on a graphite disk by chemical vapor deposition (CVD). The micrographs and element composition of Pt/GCNFs/graphite electrode were characterized by scanning electron microscopy (SEM) and electron diffraction spectroscopy (EDS). The electrocatalytic properties of Pt/GCNFs/graphite electrode for methanol oxidation have been investigated by CV and excellent electrocatalytic activity can be observed even at very low platinum loading (md=8.79 microg cm(-2)). The highest mass activity (MA) for methanol oxidation reaches 323 Ag(-1) when Pt/GCNFs/graphite electrode was cycled at a sweep rate of 50 mVs(-1) by CV in 2 M CH3OH+1 M H2SO4 aqueous solutions. This may be attributed to the small particle size and high dispersion of platinum particles coated on GCNFs and shows good potential application in direct methanol fuel cell (DMFC). Additionally, the long-term cycling stability of platinum catalysts was also investigated.     

Electrooxidation of methanol on upd-Ru and upd-Sn modified Pt electrodes

The electrochemical oxidation of methanol has been investigated on underpotentially deposited-ruthenium-modified platinum electrode (upd-Ru/Pt) and on underpotentially deposited-tin-modified platinum electrode (upd-Sn/Pt). The submonolayers of upd-Ru and upd-Sn on a Pt electrode increased the rate of methanol electrooxidation several times as large as that on a pure Pt electrode. The best performance for methanol electrooxidation was obtained on a ternary platinum based catalyst modified by upd-Ru and upd-Sn simultaneously. The influence of the submonolayers of upd-Ru adatoms and upd-Sn adatoms on the oxidation of methanol in acid has been investigated. The effect of Ru on methanol electrooxidation lies on the distribution of Ru adatoms on a Pt surface. It has been shown that as long as the amount of upd-Ru deposits were controlled in a proper range, upd-Ru deposits would enhance the methanol oxidation obtained on a Pt electrode at whichever deposition potential the upd-Ru deposits were obtained. The effects of tin are sensible to the potential range. The enhancement effect of upd-Sn adatoms for the oxidation of methanol will disappear as the electrode potential is beyond a certain value. It is speculated that there exists a synergetic effect on the Pt electrode as adatoms Ru and Sn participate simultaneously in the methanol oxidation.