等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

Controlled release of volatiles under mild reaction conditions: from nature to everyday products

Volatile organic compounds serve in nature as semiochemicals for communication between species, and are often used as flavors and fragrances in our everyday life. The quite limited longevity of olfactive perception has led to the development of pro-perfumes or pro-fragrances--ideally nonvolatile and odorless fragrance precursors which release the active volatiles by bond cleavage. Only a limited amount of reaction conditions, such as hydrolysis, temperature changes, as well as the action of light, oxygen, enzymes, or microorganisms, can be used to liberate the many different chemical functionalities. This Review describes the controlled chemical release of fragrances and discusses additional challenges such as precursor stability during product storage as well as some aspects concerning toxicity and biodegradability. As the same systems can be applied in different areas of research, the scope of this Review covers fragrance delivery as well as the controlled release of volatiles in general.     

双氧水氧化环己烯催化合成己二酸研究进展

评述了近年来以环己烯为底物,双氧水为氧源,分别采用钨酸盐、钨酸、杂多酸及杂多酸盐、功能化分子筛和负载离子液体等为催化剂催化合成己二酸的研究进展.     

Enzyme-based biocatalysis for the treatment of organic pollutants and bioenergy production

Enzyme-based biocatalysis is emerging as an advanced technique to develop green processes that help to maintain the sustainability of the environment. The bioremediation of toxic organic pollutants and waste to bioenergy production using enzymes as biocatalysts is rapidly growing due to its eco-friendly and sustainable nature. Additionally, a range of microbial species that typically grow on organic wastes can be used to produce these enzymes in an efficient manner. This is seen as a potential strategy for the development of cost-effective manufacturing for a number of biotechnological applications. The present study discusses biocatalysis as a promising and sustainable method toward the bioremediation of hazardous organic pollutants as well as for bioenergy production, based on the immense potential of enzymes as biocatalysts. Emphasis has been placed on evaluating the critical elements that can enhance the production of enzymes used as biocatalysts, as well as their functional effectiveness and stability.     

三明治式双极膜的制备及其光催化性能

以Cr3+交联羧甲基纤维素钠(CMC)作为阳膜层,戊二醛改性壳聚糖(CS)作为阴膜层,纳米TiO2光催化剂作为双极膜的中间层,在TiO2上涂布光敏剂八羟基喹啉（Oxine）以增强其光催化解离水的性能,制备了三明治式的双极膜（mCMC/TiO2-Oxine/mCS BPM)。 该双极膜在紫外光照射下,具有高的水解离效率,优良的亲水性能,双极膜阻抗小,工作电压低,当工作电流密度达0.12 A/cm2时,电槽工作电压小于5.0 V。     

Aptamers: molecular tools for analytical applications

Aptamers are artificial nucleic acid ligands, specifically generated against certain targets, such as amino acids, drugs, proteins or other molecules. In nature they exist as a nucleic acid based genetic regulatory element called a riboswitch. For generation of artificial ligands, they are isolated from combinatorial libraries of synthetic nucleic acid by exponential enrichment, via an in vitro iterative process of adsorption, recovery and reamplification known as systematic evolution of ligands by exponential enrichment (SELEX). Thanks to their unique characteristics and chemical structure, aptamers offer themselves as ideal candidates for use in analytical devices and techniques. Recent progress in the aptamer selection and incorporation of aptamers into molecular beacon structures will ensure the application of aptamers for functional and quantitative proteomics and high-throughput screening for drug discovery, as well as in various analytical applications. The properties of aptamers as well as recent developments in improved, time-efficient methods for their selection and stabilization are outlined. The use of these powerful molecular tools for analysis and the advantages they offer over existing affinity biocomponents are discussed. Finally the evolving use of aptamers in specific analytical applications such as chromatography, ELISA-type assays, biosensors and affinity PCR as well as current avenues of research and future perspectives conclude this review.     

Chemical reaction and Soret effects on MHD convective flow of second grade fluid through an absorbent medium with ramped wall temperature as well as ramped surface concentration

In the present paper, the heat generating and/or absorption as well as thermo-diffusion on the unsteady free convection MHD gyrating flow of radiation and chemical reactive second grade fluid past an unbounded perpendicular plate during absorbent medium have been discussed. Here, it is assumed that, the confining plate has the ramped wall temperature with ramped surface concentration and isothermal temperature with ramped surface concentration. The analytical solutions for the governing equations are found by utilization of Laplace transformation methodology. The velocity, temperature and concentration profiles are analyzed with quite few figures. It is determined that, velocity, temperature and concentration distribution sketches in case of ramped temperature as well as ramped surface concentration are not as much of as those of isothermal temperature as well as ramped surface concentration. In addition to the idioms of skin friction, Nusselt number as well as Sherwood number are achieved and characterized numerically with tabular format.     

咪草烟分子印迹聚合物的制备及其选择性吸附性能的研究

以丙烯酸为聚合单体,TMPTA为交联剂,AIBN为引发剂,咪草烟为模板分子,采用在低温光聚合的方法,制备了对咪草烟分子具有选择性识别能力的分子印迹聚合物．通过IR和HPLC表征,咪草烟分子印迹聚合物对咪草烟分子具有良好的识别作用．     

Low-field NMR for quality control on oils

Oil is a prominent, but multifaceted material class with a wide variety of applications. Technical oils, crude oils as well as edibles are main subclasses. In this review, the question is addressed how low-field NMR can contribute in oil characterization as an analytical tool, mainly with respect to quality control. Prerequisite in the development of a quality control application, however, is a detailed understanding of the oils and of the measurement. Low-field NMR is known as a rich methodical toolbox that was and is explored and further developed to address questions about oils, their quality, and usability as raw materials, during production and formulation as well as in use.     

Dithiocarbamates as Precursors in Organic Chemistry; Synthesis and Uses

Abstract

Organic dithiocarbamates have received great attention due to their interesting chemistry and wide utility as radical precursors and intermediates in organic synthesis. They also have found many of applications, that is, in agriculture and medicine. They are in use as pesticides, as well as in the rubber industries as vulcanization accelerators; and as antioxidants. Because they exhibit strong metal-binding capacity, they can act as in inhibitors of enzymes and have a profound effect on biological systems. Moreover, they have found application in the treatment of cancer and HIV.     

Analytical devices based on light-emitting diodes – a review of the state-of-the-art

A general overview of the development of the uses of light-emitting diodes in analytical instrumentation is given. Fundamental aspects of light-emitting diodes, as far as relevant for this usage, are covered in the first part. The measurement of light intensity is also discussed, as this is an essential part of any device based on light-emitting diodes as well. In the second part, applications are discussed, which cover liquid and gas-phase absorbance measurements, flow-through detectors for chromatography and capillary electrophoresis, sensors, as well as some less often reported methods such as photoacoustic spectroscopy.