黏弹性接触界面端附近的奇异应力场

研究蠕变加载条件下线黏弹性材料接触界面端附近的奇异应力场问题.考虑接触界面的摩擦,假设界面端的滑移方向不改变,相对滑移量微小,且其与位移同量级,由此线性化局部边界条件,根据对应原理得到Laplace变换域中的界面端应力场,导出时域中奇异应力场的卷积积分表达式.对卷积积分核函数进行数值反演,考虑接触材料的两类组合,一是持久模量具有量级上的差异,另一是持久模量接近相同.算例结果证实核函数可以用准弹性法求得的解析式较准确地近似.在此基础上,利用积分中值定理,并引入各应力分量的修正系数,得到黏弹性奇异应力场的简化式.结合核函数的数值反演结果分析修正系数表达式的取值范围,得到如下结论,若两相接触材料的持久模量相差很大,可以采用准弹性解的解析式较准确地描述界面端的奇异应力场;一般情况下,应力场不存在统一的奇异值和应力强度系数,当采用类似于准弹性解的表达式近似给出黏弹性应力场时,可以估计此近似描述的误差限.文中最后采用有限元分析黏弹性板端部嵌入部位的应力场,算例包括了黏弹性板与弹性金属支承、黏弹性板与黏弹性垫层所形成的滑移接触界面端,利用黏弹性有限元的数值结果验证理论分析所得结论的有效性.     

QFP结构中引脚焊缝界面端的奇异性热应力问题研究

由于引脚、印制电路板和焊接剂的热-机材料属性不同,在受到热载荷或机械载荷时,引脚焊接界面端会产生奇异性应力,有可能产生界面开裂.为了基于界面端奇异场来评价QFP结构引脚界面端力学行为,本文拟采用数值方法求解引脚焊缝任意角度尖劈界面端的应力强度系数.具体步骤为:首先,基于高次内插有限元特征分析法确定两相任意角度尖劈界面端的奇异性指数和应力角分布函数,并引入常数热应力项,获得热-机耦合奇异性应力场表达式;采用有限元分析技术和最小二乘拟合法来获得应力强度系数的数值解.文中考察了热-机材料属性对热载荷下焊接剂/印制电路板界面端应力强度系数的影响,并给出改善界面端热应力状态的建议.     

黏弹性材料界面裂纹应力场奇性分析

研究两半无限大黏弹性体间Griffith界面裂纹在简谐载荷作用下裂纹尖端动应力场的奇异特性.通过引入裂纹张开位移和裂纹位错密度函数,相应的混合边值问题归结为一组耦合的奇异积分方程.渐近分析表明裂尖动应力场的奇异特征完全包含在奇异积分方程的基本解中.通过对基本解的深入分析发现黏弹性材料界面裂纹裂尖动应力场具有与材料参数和外载荷频率相关的振荡奇异特性.以标准线性固体黏弹材料为例讨论了材料参数和载荷频率对奇性指数和振荡指数的影响.     

黏弹性体界面裂纹的冲击响应

研究两半无限大黏弹性体界面Griffith裂纹在反平面剪切突出载荷下,裂纹尖端动应力强度因子的时间响应,首先,运用积分变换方法将黏弹性混合黑社会问题化成变换域上的对偶积分方程,通过引入裂纹位错密度函数进一步化成Cauchy型奇异积分方程,运用分片连续函数法数值求解奇异积分方程,得到变换域内的动应力强度因子,再用Laplace积分变换数值反演方法,将变换域的解反演到时间域内,最终求得动应力强度因子的时间响应,并对黏弹性参数的影响进行分析。     

考虑尺寸效应的双材料轴对称界面端应力奇异性

提出了一种分析双材料轴对称界面端的应力奇异行为的特征值法.基于弹性力学空间轴对称问题的基本方程和一阶近似假设,利用分离变量形式的位移函数和无网格算法,导出了关于应力奇异性指数的离散形式的奇异性特征方程.由奇异性特征方程的特征值和特征向量,即可确定应力奇异性指数、位移角函数和应力角函数.数值求解了纤维/基体轴对称界面端模型的奇异性特征方程, 结果表明:尺寸效应参数δ(奇异点与轴对称轴的距离和应力奇异性支配区域大小的比值)影响着应力奇异性的强弱与阶次, 准一阶近似解析解只是δ>>1时的一个特例.      

纤维与基体的轴对称界面端附近的奇异应力场

基于各向性弹性力学空间轴对称问题的基本方程,研究了纤维与基体的轴对称界面端的应力奇异性,并给出了界最佳 近的奇异应力场。研究结果表明,该轴对称界面端的应力奇异性与平面应变状态下相应模型的应力奇异性完全相同,材料对界面端附近奇异应力场的影响可用丰个双材料组合参数描述。     

粘弹性结合材料界面端奇异场

在电子封装等结构中存在大量的粘弹性界面问题,其破坏一般均始于界面端,但目前尚无关于粘弹性界面端奇异场的解.粘弹性问题在拉普拉斯域内与弹性问题有对应关系,理论上可以利用对应性原理由弹性解经拉氏逆变换得到粘弹性问题的解.但是,对于粘弹性界面端,由于奇异场的奇异指数也是与时间有关的,因此进行严密的拉氏逆变换是非常困难的.本文借鉴弹性界面端奇异场,近似地给出了线性粘弹性体界面端奇异场的具体形式,并通过数值计算验证了近似理论解的有效性.     

立方晶粒任意集合下的格林函数和有效弹性刚度张量

为了推导多晶体材料的有效弹性刚度张量,给出立方晶粒任意集合的格林函数封闭但近似的表达式,该格林函数表达式包含三个单晶弹性常数和多晶体材料五个织构系数,它考虑取向分布函数的影响直至织构系数的线性项,它适用于弱织构多晶体材料或具有弱各向异性晶粒的多晶体材料(如金属铝),它与Nishioka格林函数近似式的比较通过三个算例给出;Synge的格林函数积分式则直接通过数值计算完成,它可作为问题的精确解供参考．该文还简单介绍了多晶体材料有效弹性刚度张量的推导过程,并把所得结果和有限元计算结果进行比较。     

尖端具有吸附性接触的界面裂纹对瞬态弹性波作用下的动态响应

建立并研究一类接触型界面裂纹模型对瞬态弹性波作用下的动态响应问题。文中利用积分变换和积分方程法推导了确定这类问题的奇异积分方程组。采用围道积分技术和切比雪夫多项式展开技术，得到了待定系数的非线性代数方程组。最后给出了裂纹尖端接触区大小和接触应力随时间变化的数值结果，揭示了这种接触裂纹的动力学特性及物理上的合理性。     

界面裂纹尖端的动态奇异特性

本文研究了界面裂纹尖端的动态应力场的奇异特性.引入尖端无摩擦接触的界面裂纹模型并采用具有运动边界的控制积分方程.证明了在动态界面裂纹尖端仅存在平方根奇异的应力场.数值结果表明接触区中的正应力确保持为压应力.为表现界面裂纹的动态特性,给出了应力强度因子和裂纹面接触区尺寸的数值结果.     

Numerical analysis of the stress concentration near holes originating in previously loaded viscoelastic bodies at finite strains

The state of stress and strain of previously loaded viscoelastic bodies with holes originating in them, successively or simultaneously, is analyzed under finite plane deformations. The problem statement and solution are based on the theory of repeatedly superimposed large deformations. The material mechanical properties are described using integral relations of the convolution type over time with a weakly singular kernel. The problem solving is based on the finite-element method. To calculate the integral of the convolution type, a recurrence formula is used that can be obtained by approximating the initial kernel with a linear combination of exponential functions (the truncated Prony’s series). The nonlinear effects and the effect of the interaction between holes on the stress concentration are analyzed. For the dynamic problems, the results for incompressible and weakly compressible materials are compared.     

功能梯度夹层多个环形界面裂纹扭转冲击

研究位于功能梯度层和外部均匀材料之间多个环形界面裂纹的扭转冲击问题,功能梯度材料 (FGM)粘结在两种不同的弹性材料之间,功能梯度层和外部材料之间环形界面裂纹的数目是任意的．引进积分变换和位错密度函数将问题化为求解Laplace域里标准的Cauchy奇异积分方程,进而化为求解代数方程;应用Laplace数值反演技术,计算时域里的动应力强度因子(DSIF)．考查了结构几何尺度和材料特性对裂尖动态断裂特性的影响．数值结果表明,DSIF存在一个主峰,到达主峰后,在其相应的静态值附近波动并最终趋于稳定;增加FGM的梯度能减小DSIF的峰值．     

Tractive rolling contact mechanics of graded coatings

In this study, the tractive rolling contact problem between a rigid cylinder and a graded coating is investigated. The main objective of this study is to investigate the effect of the stiffness ratio, the coefficient of friction and the coating thickness on the surface contact tractions, the surface in-plane stress, the stick zone length and the creep ratio parameter that may have a bearing on the fatigue life of the component. Assuming that the shear modulus varies exponentially through the thickness of the coating, the governing integral equations associated with the rolling contact problem are constructed. Furthermore, it is supposed that the contact patch is controlled by a central stick zone accompanied by two slip zones. The conventional Goodman approximation is employed in order to decouple the governing singular integral equations. Finally, the numerical solution of the integral equations is obtained by applying the Gauss–Chebyshev integration method.     

Propagation of slip pulse along frictionless contact interface with local separation between two piezoelectric solids

The Stroh formalism of piezoelectric materials,Fourier analysis and singular integral equation technique were used to investigate the existence of a pulse at the fric- tionless interface in presence of local separation between two contact piezoelectric solids. The two solids were combined together by uniaxial tractions and laid in the electric field. The problem was cast into a set of Cauchy singular integral equations,from which the closed-form solutions were derived.The numerical discussion on the existence of such a slip pulse was presented.The results show that such a slip pulse,which has square root singularities at both ends of the local separation zone,can propagate in most material combinations.And the existence of such a slip pulse will not be affected by the applied mechanical and electric fields in some special material combinations.     

The scattering of general SH plane wave by interface crack between two dissimilar viscoelastic bodies

The scattering of general SH plane wave by an interface crack between two dissimilar viscoelastic bodies is studied and the dynamic stress intensity factor at the crack-tip is computed. The scattering problem can be decomposed into two problems: one is the reflection and refraction problem of general SH plane waves at perfect interface (with no crack); another is the scattering problem due to the existence of crack. For the first problem, the viscoelastic wave equation, displacement and stress continuity conditions across the interface are used to obtain the shear stress distribution at the interface. For the second problem, the integral transformation method is used to reduce the scattering problem into dual integral equations. Then, the dual integral equations are transformed into the Cauchy singular integral equation of first kind by introduction of the crack dislocation density function. Finally, the singular integral equation is solved by Kurtz's piecewise continuous function method. As a consequence, the crack opening displacement and dynamic stress intensity factor are obtained. At the end of the paper, a numerical example is given. The effects of incident angle, incident frequency and viscoelastic material parameters are analyzed. It is found that there is a frequency region for viscoelastic material within which the viscoelastic effects cannot be ignored. This work was supported by the National Natural Science Foundation of China (No.19772064) and by the project of CAS KJ 951-1-20     

Interaction of general plane P wave and cylindrical inclusion partially debonded from its viscoelastic matrix

The interaction of a general plane P wave and an elastic cylindrical inclusion of infinite length partially debonded from its surrounding viscoelastic matrix of infinite extension is investigated. The debonded region is modeled as an arc-shaped interface crack between inclusion and matrix with non-contacting faces. With wave functions expansion and singular integral equation technique, the interaction problem is reduced to a set of simultaneous singular integral equations of crack dislocation density function. By analysis of the fundamental solution of the singular integral equation, it is found that dynamic stress field at the crack tip is oscillatory singular, which is related to the frequency of incident wave. The singular integral equations are solved numerically, and the crack open displacement and dynamic stress intensity factor are evaluated for various incident angles and frequencies. The project supported by the National Natural Science Foundation of China (19872002) and Climbing Foundation of Northern Jiaotong University     

Closed-form solution for the contact problem of reinforced pin-loaded joints used in glass structures

In a typical pin-loaded joint used to assemble glass plates, the hole in a glass plate is reinforced by a steel ring glued to the glass plate via a soft resin layer. Thus, the ring is in direct contact with the steel bolt and prevents the glass plate from high stress concentration. This paper proposes an analytical approach to solving the resulting conforming contact problem. The strain and stress fields inside the resin layer are first determined by exploiting the fact that the stiffness of the material constituting it is much smaller than the stiffness of steel and glass. After finding the relevant Green functions for the ring and pin, the frictionless contact between them is then formulated in terms of an integral equation with a Fourier series as the kernel. This integral equation is solved by neglecting the terms of high orders and transforming it into the Cauchy singular integral equation. The derived analytical results for the contact pressure and angle are finally compared to and validated by those obtained by the finite element method.     

各向异性弹性体光滑接触界面上的滑移脉冲波

利用Stroh公式,Fourier分析和奇异积分方程技术研究了两各向异性弹性半空间光滑接触可分离界面上滑移脉冲波的存在及其传播特性。结果表明,如果至少能在一种介质中存在Rayleigh波,且其波速小于两种介质中的最小极限速度,则滑移脉冲波就可以存在。这种脉冲波传播速度不确定,可在最小极限波速与较低的Rayleigh波速之间取值,而该取值范围又取决于无界面分离情况下的第一、第二滑移波的解。分离区大小取决于扰动的强度,界面法向力和质点速度在分离区两端有 1 /2奇异性。