Thermal properties of solvolysis lignin-derived polyurethanes

Thermal properties of polyurethane (PU) films prepared from solvolysis lignin (SL), polyethylene glycol (PEG) and diphenylmethane diisocyanate (MDI) were examined by differential scanning calorimetry and thermogravimetry. In the SL—PEG—MDI system, the SL content, the molecular weight (M_n) of PEG and the NCO/OH ratio were changed in order to control the thermal properties. Glass transition temperatures (T_g's) of the prepared PU's were dependent on the SL content, the M_n of PEG and the NCO/OH ratio. However, the T_g of PU was significantly influenced by the SL content: the increment of T_g was ca. 150 K when the SL content in PEG increased from 0 to ca. 50%. The decomposition of the PU's was markedly dependent on the content of SL. Other factors, such as the NCO/OH ratio and the M_n of PEG, are less dominant compared with the SL content. This fact suggests that the dissociation between the isocyanate groups and the phenolic OH groups in SL may be the major factor in the whole process of the thermal decomposition of the PU containing SL     

Synthesis and physical properties of polyurethanes from saccharide-based polycaprolactones

Polyurethane (PU) sheets were prepared from glucose-, fructose-and sucrose-based polycaprolactones (PCL). The obtained saccharide-based PCL's were characterized by gel permeation chromatography, Fourier-transform infrared spectroscopy and nuclear magnetic resonance spectroscopy. The glass transition temperature, thermal degradation temperature, tensile strength, elongation and Young's modulus of the PU sheets were measured. The obtained results suggest that the molecular motion of PU's is enhanced with increasing fraction of PCL chains in PU molecules, and that at the same time the saccharide components act as hard segments.     

Thermal properties of lignin-and molasses-based polyurethane foams

Lignin-and molasses-based polyurethane (PU) foams with various lignin/molasses mixing ratios were prepared. The hydroxyl group in molasses and lignin is used as the reaction site and PU foams with various isocyanate (NCO)/the hydroxyl group (OH) ratios were obtained. Thermal properties of PU foams were investigated by differential scanning calorimetry (DSC), thermogravimetry (TG) and thermal conductivity measurement. Glass transition temperature (T _g) was observed depending on NCO/OH ratio in a temperature range from ca. 80 to 120°C and thermal decomposition temperature (T _d) from ca. 280 to 295°C. Mixing ratio of molasses and lignin polyol scarcely affected the T _g and T _d. Thermal conductivity of PU foams was in a range from 0.030 to 0.040 Wm⁻¹ K⁻¹ depending on mixing ratio of lignin and molasses.     

Preparation of high‐temperature polyurethane by alloying with reactive polyamide

A series of novel poly(urethane amide) films were prepared by the reaction of a polyurethane (PU) prepolymer and a soluble polyamide (PA) containing aliphatic hydroxyl groups in the backbone. The PU prepolymer was prepared by the reaction of polyester polyol and 2,4‐tolylenediisocyanate and then was end‐capped with phenol. Soluble PA was prepared by the reaction of 1‐(m‐aminophenyl)‐2‐(p‐aminophenyl)ethanol and terephthaloyl chloride. The PU prepolymer and PA were blended, and the clear, transparent solutions were cast on glass substrates; this was followed by thermal treatments at various temperatures to produce reactions between the isocyanate group of the PU prepolymer and the hydroxyl group of PA. The opaque poly(urethane amide) films showed various properties, from those of plastics to those of elastomers, depending on the ratio of the PU and PA components. Dynamic mechanical analysis showed two glass‐transition temperatures (T_g's), a lower T_g due to the PU component and a higher T_g due to the PA component, suggesting that the two polymer components were phase‐separated. The rubbery plateau region of the storage modulus for the elastic films was maintained up to about 250 °C, which is considerably higher than for conventional PUs. Tensile measurements of the elastic films of 90/10 PU/PA showed that the elongation was as high as 347%. This indicated that the alloying of PU with PA containing aliphatic hydroxyl groups in the backbone improved the high‐temperature properties of PU and, therefore, enhanced the use temperature of PU. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3497–3503, 2002     

Novel method for the preparation of poly(urethane–imide)s and their properties

A polymer blend consisting of polyimide (PI) and polyurethane (PU) was prepared by means of a novel approach. PU prepolymer was prepared by the reaction of polyester polyol and 2,4-tolylenediisocyanate (2,4-TDI) and then end-capped with phenol. Poly(amide acid) was prepared from pyromellitic dianhydride (PMDA) and oxydianiline (ODA). A series of oligo(amide acid)s were also prepared by controlling the molar ratio of PMDA and ODA. The PU prepolymer and poly(amide acid) or oligo(amide acid) solution were blended at room temperature in various weight ratios. The cast films were obtained from the blend solution and treated at various temperatures. With the increase of polyurethane component, the films changed from plastic to brittle and then to elastic. The poly(urethane–imide) elastomers showed excellent mechanical properties and moderate thermal stability. The elongation of films with elasticity was more than 300%. The elongation set after the breaking of films was small. From the dynamic mechanical analysis, all the samples showed a glass transition temperature (T_g) at ca. −15°C, corresponding to T_g of the urethane component, suggesting that phase separation occurred between the two polymer components, irrespective of polyimide content. TGA and DSC studies indicated that the thermal degradation of poly(urethane–imide) was in the temperature range 250–270°C. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3745–3753, 1997     

Effect of cyclobutane carbonitrile rings on the glass transition temperature of vinyl copolymers

A wide compositional range of copolymers of 1-cyclobutene carbonitrile (CBCN) and 1-bicyclobutance carbonitrile (BBCN) with common vinyl monomers was prepared in order to study systematically the effect of cyclobutane carbonitrile ring incorporation on the glass transition temperature (T_g). In general, the T_g's of the copolymers are increased in proportion to the weight percent of the small-ring monomer incorporated, but the 1,2-mode of incorporation raises T_g more than the 1,3-mode. Attempts were made to correlate data with quantitative T_g–composition relationships (Fox–Johnston equations). Prediction for nitrile homopolymer T_g's are compared with literature values.     

Carbon nanotube–polyurethane shape memory nanocomposites with low trigger temperature

Ester-based polyurethane (PU) with low glass transition temperature was used to develop shape memory nanocomposites with low trigger temperature. Pristine carbon nanotubes (CNTs) and oxidized CNTs (ox-CNTs) were introduced by melt mixing to improve the mechanical and shape memory properties of the PU matrix. The dispersion of CNTs on the mechanical properties and shape memory behaviors of the nanocomposites were also investigated. The results show that better dispersion of ox-CNTs contributes to more stiffness effect below glass transition temperature (T_g) while lower storage modulus (E′) above T_g. The nanocomposites exhibit high shape fixity and recovery ratio above 98%. The ox-CNT/PU nanocomposite shows higher shape recovery ratio for the first cycle, faster recovery due to better dispersion of CNTs and have potential applications for controlling tags or proof marks in the area of frozen food. The trigger temperature can be tailored by controlling the T_g of the PU matrix or the content of the nanofillers.     

Environmentally Compatible Hybrid-Type Polyurethane Foams Containing Saccharide and Lignin Components

Semi-rigid polyurethane (PU) foams were prepared using lignin-molasses- poly(ethylene glycol) polyols. Two kinds of lignin, kraft lignin (KL) and sodium lignosulfonate (LS), were used. Both lignin and molasses polyols were mixed with various ratios and were reacted with poly(phenylene methylene) polyisocyanate (MDI) in the presence of silicone surfactant and di-n-butyltin dilaurate. A small amount of water was used as a foaming agent. The apparent density of PU foams increased with increasing lignin content. The compression strength and elastic modulus linearly increase with increasing apparent density, suggesting that mechanical properties are controllable by changing reaction conditions. The PU foams were amorphous and glass transition was detected by differential scanning calorimetry. The glass transition temperature (T_g ) maintained an almost constant value, regardless of the mixing ratio. This indicates that both the phenolic group of lignin and the glucopyranose ring of molasses act as rigid components in PU crosslinking network structures, and both groups contribute to the main chain motion to the same extent. By thermogravimetry (TG), it was confirmed that PU foams are thermally stable up to around 300 °C. By differential scanning calorimetry, T_g was observed at temperatures from 80 to 120 °C.     

Effects of curing on the glass transition temperature and moisture absorption of a neat epoxy resin

Apparent glass transition temperature (T_g) measurements were made on smaples of a neat epoxy resin that had been cured at four different temperature and for four different times at each temperature. The apparent T_g data increase with cure time toward an asymptote that was dependent on cure temperature. The asymptotic dependence of T_g on cure temperature may be explained by the effect of cure temperature on the reaction rates and available reaction sites. The asymptotic increase with cure time may be understood in terms of the resin's extent of cure. Moisture-conditioning studies were also made and the amount of moisture absorbed was correlated with the extent of cure. The absorbed moisture's interaction with the resin's molecular structure was deduced to by primarily at hydroxyl sites.     

Structure-property relationship of polyurethane ionomer

Polyurethane (PU) ionomers were prepared using various types of polyol (PTAd, PCL, PTMG, and PPG) and isocyanate (MDI, HDI, and IPDI), together with different extender (DMPA) contents, degree of neutralization, and number average molecular weight (M _n) of polyol. Modulus (E), strength (_b), and glass transition temperature (T _g) significantly increased with the increased amount of extender and extender neutralization. Among three of the iocyanate used, PU from MDI gave the highest modulus, strength, andT _g. With regard to theM _n of PTAd (600, 1000, 2000), PU from PTAd 600M _n gave the highest modulus, strength, andT _g, due probably to the highest hard segment content and phase mixing. On the other hand, PU from PTAd 2000M _n gave significantly improved strength over PTAd 1000M _n, and the highest elongation. The results were interpreted in terms of soft-segment crystallization, and soft-hard phase separation, which was concluded from the lowered softT _g.     

A study on the glass transition behavior and morphology of semi-interpenetrating polymer networks

The epoxy resin/polyurethane semi-IPN was prepared and the glass transition behavior of the semi-IPN was discussed with DSC and DMA methods. The results show that the two glass transition temperatures (T_g) referring to epoxy resin and polyurethane respectively get closer. Between the two T_g there exists another T_g related to the interface between the two polymers. SEM indicates that this semi-IPN has a two-phase continuous structure which changes with different weight compositions. This is also proved by testing the Young's modulus. It is found that the IPN system has a cellular structure. Comparatively, the compatibility between the two polymers is the best when the weight ratio of EP/PU is 70/30. © 1996 John Wiley & Sons, Inc.     

Effects of organophilic montmorillonite on hydrogen bonding, free volume and glass transition temperature of epoxy resin/polyurethane interpenetrating polymer networks

Epoxy resin nanocomposites containing organophilic montmorillonite (oM) and polyurethane were prepared by adding oM to interpenetrating polymer networks (IPNs) of epoxy resin and polyurethane (EP/PU). The dispersion degree of oM in EP/PU matrix was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Fourier transform infrared spectrometry (FT-IR) showed that strong interactions existed between oM and EP/PU matrix, and oM had some effect on hydrogen bonding of these EP/PU IPNs nanocomposites. Positron annihilation spectroscopy (PALS) and differential scanning calorimetry (DSC) measurements were used to investigate the effect of oM and PU contents on free volume and glass transition temperature (T_g) of these nanocomposites. The PALS and DSC results clearly showed that the presence of oM led to a decrease in the total fractional free volume, which was consistent with increasing T_g upon addition of oM, ascribed to increasing hydrogen bonding in interfacial regions of oM and EP/PU matrix and enhancing the miscibility between EP phase and PU phase. In addition, with increasing PU content, the total fractional free volume increased, corresponding to decreasing T_g.     

3D diamond‐containing nanocomposites based on hybrid polyurethane–poly(2‐hydroxyethyl methacrylate) semi‐IPNs: Composition‐nanostructure‐segmental dynamics‐elastic properties relationships

Nanostructure, glass transition dynamics and elastic properties were studied in the 3D nanodiamond‐containing composites based on polyurethane‐poly(2‐hydroxyethyl methacrylate) semi‐interpenetrating polymer networks (PU‐PHEMA semi‐IPNs), neat PU or PHEMA matrices. Nanodiamond (ND) content in the nanocomposites varied from 0.25 to 3 wt %. Combined differential scanning calorimetry/ laser‐interferometric creep rate spectroscopy/atomic force microscopy approach was utilized. A large impact of small 3D ND additives on PU‐PHEMA networks' dynamics and properties was revealed under conditions when an average inter‐particle distance L exceeds by far gyration radius R_g. The pronounced heterogeneity of glass transitions' dynamics and two opposite effects were observed. The main effect was a strong suppression of PHEMA glass transition dynamics at 90–180 °C, with the enhancement of creep resistance and threefold to sixfold increasing modulus of elasticity. The peculiarly crosslinked structure of nanocomposites, due to double covalent hybridization, resulted in low rheological percolation threshold, and a synergistic effect in dynamics was observed. Less pronounced effect of accelerating dynamics in the temperature region between β‐ and α‐transitions in PHEMA was associated with dynamics in domains with loosened molecular packing. The distinct physical limit for “anomalous” decreasing T_g is predicted in terms of the notion of the common segmental nature of α‐ and β‐relaxations. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1696–1712, 2008     

Synthesis of novel cyclic olefin polymers with excellent transparency and high glass‐transition temperature via gradient copolymerization of bulky cyclic olefin and cis‐cyclooctene

Novel cyclic olefin polymers (COPs) with excellent transparency and high glass‐transition temperature (T_g) synthesized from bulky norbornene derivative, exo‐1,4,4a,9,9a,10‐hexahydro‐9,10(1',2')‐benzeno‐l,4‐methanoanthracene (HBMN), and cis‐cyclooctene (COE) by ring‐opening metathesis copolymerization utilizing the “first‐generation Grubbs” catalyst, RuCl₂(PCy₃)₂(CHPh), and subsequent hydrogenation was reported herein. To get amorphous copolymers, it was of great importance to control the feed ratios and the polymerization time for gradient copolymerization. All these copolymers showed very high T_gs (141.1–201.2 °C), which varied with the content of HBMN. The films of the gradient copolymers with only one T_g were highly transparent. On the contrary, all the block copolymers synthesized through sequential addition showed two thermal transition temperatures, T_g and melt temperature (T_m), and the films of these block copolymers were opaque. The mechanical performances of the COPs were also investigated. It is the first report that transparent COP could be prepared from bulky norbornene derivative and monocyclic olefin. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3240–3249     

Synthesis and thermal properties of cellulose-based polycaprolactones

Cellulose-based polycaprolactone (CAPCL) sheets were prepared from cellulose acetate (CA) and ϵ-caprolactone (CL). Thermal properties of the obtained CAPCL's were studied by differential scanning calorimetry (DSC), thermogravimetry (TG) and TG-Fourier transform infrared spectrometry (TG-FTIR). The glass transition temperatures (T_g 's) of CAPCL decreased with increasing CL/OH ratio, until CL/OH ratio reached 15 and then increased above that ratio. Melting of CAPCL was observed when CL/OH ratio was over 10. The thermal degradation temperatures (T_d 's) of CAPCL increased from ca. 350 °C to 390 °C with increasing CL/OH ratio. The results obtained by TG-FTIR analysis of CAPCL showed that gases with OH, CH, C=O, C-O-C groups evolved by thermal degradation.     

Preparation and properties of new random and block copolyamides derived from 1,3-bis(3-aminopropyl)tetramethyldisiloxane,aromatic diamines,and isophthaloyl chloride

Random and block disiloxane-containing copolyamides were prepared through one- and two-step procedures, respectively, by the low temperature solution polycondensation in chloroform containing triethylamine hydrochloride starting from 1,3-bis(3-aminopropyl)tetramethyldisiloxane, an aromatic diamine [3,4'-diaminodiphenyl ether (ODA) or m-phenylenediamine], and isophthaloyl chloride. The random copolyamides exhibited composition-dependent single glass transition temperature (T_g), and gave transparent and tough films by solution casting or hot pressing. The ODA-based block copolyamides had two T_g's, and the solvent-cast transparent films exhibited microphase separated morphology. The block copolymers gave better quality films than the single-phase random copolymers. © 1992 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(urethane‐benzoxazine) films as novel type of polyurethane/phenolic resin composites

Poly(urethane‐benzoxazine) films as novel polyurethane ( PU )/phenolic resin composites were prepared by blending a benzoxazine monomer ( Ba ) and PU prepolymer that was synthesized from 2,4‐tolylene diisocyanate (TDI) and polyethylene adipate polyol (MW ca. 1000) in 2 : 1 molar ratio. DSC of PU/Ba blend showed an exotherm with maximum at ca. 246 °C due to the ring‐opening polymerization of Ba, giving phenolic OH functionalities that react with isocyanate groups in the PU prepolymer. The poly(urethane‐benzoxazine) films obtained by thermal cure were transparent, with color ranging from yellow to pale wine with increase of Ba content. All the films have only one glass transition temperature (T_g ) from viscoelastic measurements, indicating no phase separation in poly(urethane‐benzoxazine) due to in situ polymerization. The T_g increased with the increase of Ba content. The films containing 10 and 15% of Ba have characteristics of an elastomer, with elongation at break at 244 and 182%, respectively. These elastic films exhibit good resilience with excellent reinstating behavior. The films containing more than 20% of Ba have characteristics of plastics. The poly(urethane‐benzoxazine) films showed excellent resistance to the solvents such as tetrahydrofuran, N,N‐dimethyl formamide, and N‐methyl‐2‐pyrrolidinone that easily dissolve PU s. Thermal stability of PU was greatly enhanced even with the incorporation of a small amount of Ba . © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4165–4176, 2000     

Basic structure–property behavior of polyurethane cationomers

Polyurethane (PU) cationomers were synthesized from polytetramethylene adipate glycol (PTAd), isophorone diisocyanate (IPDI), and N-methyl diethanolamine (MDEA) according to a prepolymer mixing process. Basic structure-property behavior of the emulsion (obtained by adding water to the ionomer solution) and emulsion cast film was studied with regard to the molecular weight (M_n) of PTAd, MDEA content, degree of neutralization, and extender functionality. Particle size decreased asymptotically with increasing M_n of PTAd due to the increased chain flexibility, and with the degree of neutralization due to the increased hydrophilicity of the PU. Emulsion viscosity generally showed the opposite tendency with particle size dependence. The major transition temperature, corresponding to the glass transition (T_g) of phase mixed PU or hard segment-rich phase of the PU monotonically increased with MDEA content, degree of neutralization, and with increasing extender functionality. However, with increasing M_n of PTAd, T_g first decreased (M_n = 1000) and then increased (M_n = 1500, 2000), due respectively to the increased hard fraction of phase mixed PU, and soft segment crystallization. Tensile strength increased and elongation at break decreased with MDEA content, degree of neutralization, and extender functionality. © 1994 John Wiley & Sons, Inc.     

Depression of the glass transition temperature of poly(methyl methacrylate) by plasticizers: Conformity with free volume theory

Mixtures of poly(methyl methacrylate) (PMMA) and plasticizer were made by γ-irradiation of mixtures of methyl methacrylate with diethyl phthalate or with dioctyl phthalate. The glass transition temperature T_g was determined by differential scanning calorimetry. Plots of T_g versus volume fraction of PMMA were found to conform to the simple free volume theory of Kelley and Bueche, using physical property values either reported in the literature or else calculated by Bondi's procedures.     

Polyurethane Ionomers from Cycloaliphatic Diisocyanate and Polytetramethylene Glycol

Abstract

Segmented polyurethane (PU) ionomers were prepared from cycloaliphatic diisocyanate [methylene bis(4-cyclohexyl isocyanate) (H₁₂MDI) and isophoron diisocyanate (IPDI)] and polytetramethylene glycol (PTMG) by using an anionic-type chain extender, viz., dimethylol propionic acid (DMPA). The effect of ionic content and butanediol (BD) on the state of dispersion and physical properties of emulsion-cast film was determined using Autosizer, transmission electron microscopy (TEM), Instron, and Rheovibron. With increased incorporations of DMPA in PU, particle size of emulsion decreased asymptotically, tensile modulus and strength increased, and the glass transition temperature (T _g) moved toward the higher temperature. On the other hand, with increased incorporation of BD in PU, particle size of emulsion, tensile modulus, and strength of the emulsion cast film increased, and the major transition of soft segment moved toward higher temperature. With regard to the structural effect of the isocyanate, H₁₂MDI gave finer dispersion and better mechanical properties over IPDI.