The influence of variant PE‐b‐PEO segments on physical properties of LLDPE graft copolymers

A method was adopted to fix a series of polymers of PE‐b‐PEO with different PEO/PE segments on the chains of LLDPE. Maleic anhydride (MA) reacting with hydroxyl group of PE‐b‐PEO (mPE‐b‐PEO) was used as the intermediate. The structures of intermediates and graft copolymers were approved by ¹H NMR and FTIR. XPS analysis revealed a great amount of oxygen on the surface of grafted copolymers although the end group of PEO was fixed on the LLDPE chains through MA. Thermal properties of the graft copolymers as determined by differential scanning calorimetry (DSC) showed that PE segments in the grafted monomers could promote the heterogeneous nucleation of the polymer, increase T_c, and crystal growth rate. While the amorphous PEO segments which attached to the crystalline PE segments in LLDPE, impaired their ability to fit the crystal lattice, and depressed the crystallization of LLDPE backbones. In this study, it was also verified through the dynamic rheological data that increasing M_n of grafted monomers significantly increased the complex viscosity and enhanced the shear‐thinning behavior. Long‐branched chains formed by grafted monomers enhanced the complex moduli (G′ and G″) value and retarded relaxation rate. However, there were little influence on the rheological properties when increasing the amounts of PEO segments (or decreasing PE segments) of grafted monomers with similar molecular weight. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 506–515, 2008     

Surface grafting of polyethylene by mutual irradiation in methyl acrylate vapor. II. High-energy electrons irradiation

Vapor-phase mutual grafting of methyl acrylate (MA) onto polyethylene (PE) at high dose rates from an electron accelerator yields the same surface graft structure as does the grafting at low dose rates from ⁶⁰Co sources; i.e., a homopolymer layer (consisting of only MA component) is easily formed on the inner graft copolymer layer (consisting of both MA and PE components) as a result of the continuously increasing surface graft composition. To produce the surface layer, 4-MeV electron irradiation with a linear electron accelerator requires only less than 3 min of irradiation time at dose rates of more than 2 Mrad/min, whereas γ irradiation with a ⁶⁰Co source requires at least 1 hr at dose rates of less than 2 × 10³ rad/min. The rate of monomer consumption (or polymerization) in the surface homopolymer layer shows no dependence of irradiation time and a positive dependence of dose rate. It has been suggested that this kinetic feature at the high dose rates shows some contribution of vapor-phase homopolymerization and subsequent deposition (onto the grafting surface) followed by recombination with the grafted side chain radicals, although secondary graft copolymerization from the grafted chain radicals is still the principal process for the growth of the surface homopolymer layer.     

Model compounds and 13C NMR increments for the characterization of maleic anhydride-grafted polyolefins

A set of model compounds that mimic the graft sites of maleic anhydride (MA) functionalized polyolefins was synthesized and characterized with NMR spectroscopy. The acquired carbon nuclear magnetic resonance data were used to deduce chemical-shift increments for the prediction of ¹³C chemical shifts of MA functionalized polyolefins. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4368–4385, 1999     

GRAFTING OF PEROXIDE-INITIATED MALEIC ANHYDRIDE ON SPHERICAL PE／PP IN-REACTOR BLEND GRANULES

Spherical polyethylene/polypropylene (PE/PP) in-reactor blend granules with various ethylene/propylene molar ratios and high porosity were synthesized using a high yield TiCl4/MgCl2 supported catalyst. A solution of benzoyl peroxide (BPO)/maleic anhydride (MAH)/xylene (interfacial reagent) or BPO/MAH/St (comonomer) was absorbed onto the PE/PP inreactor blend granules, and solid phase gratt polymerization of MAH on PE/PP was conducted. The amount of grafted MAH on PE/PP was measured through chemical titration. The results showed that solid phase graft polymerization of MAH in PE/PP in-reactor blend granules produced graft copolymer with high amount of grafted MAH, and the amount of grafted MAH was raised slightly when St was introduced as comonomer. The graft in-reactor blend was fractionated into five fractions through temperature-gradient extraction fractionation (TGEF), and the fractions were analyzed by FTIR. The results revealed that MAH is mainly grafted on the PE segments, whereas MAH was predominantly grafted on the PP segments when St was present in the graft polymerization system. In addition, the final product is still in the form of regular spherical granules, which is beneficial for industrial processing.     

A look inside the extruder: evolution of chemistry,morphology and rheology along the extruder axis during reactive processing and blending

A simple device was recently developed for fast sampling (within a few seconds) of representative melt samples (about 2 g) on a running extruder. An array of such devices has been mounted on a twin‐screw extruder. The goal of this study was to de‐black‐box reactive processing of polymers by studying some typical examples. ‐ Processing of polyolefins in the presence of peroxides: when the polymer is molten and the melt temperature is sufficiently high branching/cross‐linking of PE and degradation of PP occurs; the conversion follows a convex profile along the screw axis, which profile is similar to the exponential profile calculated for peroxide decomposition. ‐ Free‐radical grafting of maleic anhydride (MA) onto polyolefins: MA grafting onto PE and PP also follows a convex profile with branching/cross‐linking as parallel side reaction for PE and degradation for PP; for PE degradation of the formed grafted/cross‐linked gel is observed at the end of the extruder. ‐ Reactive blending of PA‐6 with EPM‐g‐MA: within a few seconds the in‐situ compatibilization reaction, resulting in PA‐6/EPM graft copolymers, is completed and the degree of rubber dispersion has changed from the mm to the sub‐μm range, regardless of the MA content of EPM‐g‐MA and the EPM‐g‐MA content of the blend; PA degradation occurs along the whole extruder.     

Synthesis and Characterization of PE-g-MA／MgAI-LDH Exfoliation Nanocomposite via Solution Intercalation

An organo‐modified MgAl‐layered double hydroxide (OMgAl‐LDH) was successfully exfoliated in the xylene solution of polyethylene‐grafted‐maleic anhydride (PE‐g‐MA) under re‐fluxing condition. A PE‐g‐MA/MgAl‐LDH exfoliation nanocomposite was formed after the precipitation of PE‐g‐MA from the dispersion system. The structure and thermal property of the PE‐g‐MA/MgAl‐LDH exfoliation nanocomposite were characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetry analysis (TGA). The disappearance of d₀₀₁ XRD peak of OMgAl‐LDH at 20 = 3.2° suggests that the MgAl hydroxide sheets are exfoliated in the nanocomposite. The TEM image shows that the MgAl hydroxide sheets of less than 70 nm in length or width are exfoliated and dispersed disorderly in PE‐g‐MA matrix. TGA profiles indicate that the PE‐g‐MA/MgAl‐LDH nanocomposite with 5 wt% OMgAl‐LDH loading shows a faster charring process in temperature range from 210 to 390 °C and a greater thermal stability beyond 390 °C than PE‐g‐MA does. The decomposition temperature of the nanocomposite is 25 °C higher than that of PE‐g‐MA as measured at 50% weight loss. The PE‐g‐MA/MgAl‐LDH nanocomposite is promising for application of flame‐retardant polymeric materials.     

Surface modification of polymers. IV. UV initiated degradation of polymers with stabilizers grafted onto the surface

Polypropylene (PP), Polyethylene (PE), and polystyrene (PS) films were grafted with glycidylmethacrylate in thin surface layers. To the oxiran groups thus grafted onto the surface three UV stabilizers were attached, 4-amino-2,2,6,6-tetramethylpiperidine (AP), 2,4-dihydroxybenzophenone (DHBP), and phenyl 4-aminosalicylate (PAS). The amount of stabilizer grafted onto the surface varied between 25 and 40 nmol/cm² depending on the polymer substrate. The samples were exposed to UV radiation in air, and the degradation and oxidation of the polymers were studied with IR, UV, and ESCA spectroscopy and by stress–strain measurements. PP grafted with AP exhibited a near 20-fold increase in lifetime compared with the unprotected PP, AP did not stabilize the PE or PS samples. DHBP was an efficient stabilizer of PE, the oxidation rate of the grafted sample being 1/2 to 1/3 of the ungrafted. A similar effect was observed when DHBP was grafted onto PP and PS. PAS underwent a rearrangement reaction when irradiated with UV light, and had only a slight stabilizing effect.     

Structural Revision and Elucidation of the Biosynthesis of Hypodoratoxide by 13C,13C COSY NMR Spectroscopy

Feeding of (2,3,4,5,6‐¹³C₅)mevalonolactone to the fungus Hypomyces odoratus resulted in a completely labeled sesquiterpene ether. The connectivity of the carbon atoms was easily deduced from a ¹³C,¹³C COSY spectrum, revealing a structure that was different from the previously reported structure of hypodoratoxide, even though the reported ¹³C NMR data matched. A structural revision of hypodoratoxide is thus presented. Its absolute configuration was tentatively assigned from its co‐metabolite cis‐dihydroagarofuran. Its biosynthesis was investigated by feeding of (3‐¹³C)‐ and (4,6‐¹³C₂)mevalonolactone, which gave insights into the complex rearrangement of the carbon skeleton during terpene cyclization by analysis of the ¹³C,¹³C couplings.     

Reducing the computational cost of NMR crystallography of organic powders at natural isotopic abundance with the help of 13C-13C dipolar couplings

Structure determination of functional organic compounds remains a formidable challenge when the sample exists as a powder. Nuclear magnetic resonance crystallography approaches based on the comparison of experimental and Density Functional Theory (DFT)-computed ¹H chemical shifts have already demonstrated great potential for structure determination of organic powders, but limitations still persist. In this study, we discuss the possibility of using ¹³C-¹³C dipolar couplings quantified on powdered theophylline at natural isotopic abundance with the help of dynamic nuclear polarization, to realize a DFT-free, rapid screening of a pool of structures predicted by ab initio random structure search. We show that although ¹³C-¹³C dipolar couplings can identify structures possessing long range structural motifs and unit cell parameters close to those of the true structure, it must be complemented with other data to recover information about the presence and the chemical nature of the supramolecular interactions.     

13C chemical shielding tensor orientations in a phosphoenolpyruvate moiety from 13C rotational-resonance MAS NMR lineshapes

The absolute orientations of the three ¹³C chemical shielding tensors in the phosphoenolpyruvate (PEP) moiety in a PEP-model compound with known crystal structure are reported. The study uses a fully ¹³C-enriched polycrystalline sample of triammonium phosphoenolpyruvate monohydrate, (NH₄)₃(PEP)⋅H₂O, and ¹³C MAS NMR experiments fulfilling various different ¹³C rotational-resonance conditions. The absolute ¹³C chemical shielding tensor orientations are derived by iterative fitting, employing numerically exact simulations, of various rotational-resonance ¹³C MAS NMR lineshapes of the three-¹³C-spin system in fully ¹³C-enriched (NH₄)₃(PEP)⋅H₂O. The implications of the results of this study for future, biochemically oriented solid-state NMR studies on the PEP moiety are outlined.     

Short-Chain Branching in Polyethylene and Poly(vinyl Chloride) Using Pyrolysis Hydrogenation Gas Chromatography and 13C Nuclear Magnetic Resonance Analysis

This study compares the use of pyrolysis hydrogenation gas chromatography (PHGC) and ¹³C Fourier transform nuclear magnetic resonance (FTNMR) methods for the analysis of reference polyethylene (PE) samples, ethylene-α-olefin copolymers, and specially prepared poly(vinyl chloride) (PVC) samples which were reduced to their PE skeletal structures. The nature and relative quantities of the short branches along the polymer chains were determined using both techniques. Improved high-resolution PHGC data, obtained with a fused silica capillary separation column, gave results which were in satisfactory agreement with the ¹³C FTNMR data. This approach confirms that detailed microstructural information can be obtained with these methods by using carefully controlled experimental conditions and appropriate reference systems.     

Identification of N-methylpyrazole analog isomers by 13C NMR

Using several N-methyl pyrazole analogs the utility of ¹³C nmr in determining isomeric structures was examined. The chemical shift assignments of the pyrazole carbons and thus the isomeric structures were determined using a combination of proton coupled and proton decoupled ¹³C nmr spectra.     

Substituent effects on 13C-15N spin couplings and 13C chemical shifts in benzenediazonium ions

Similar trends are observed for ¹J(¹³C-¹⁵N) values for a series of aryldiazonium tetrafluoroborates and comparable anilinium fluorosulfonates. Contributions from resonance structures involving double-bond character in the CN bond are judged to be relatively unimportant in the ground state structure of aryldiazonium ions.     

Preparation and characterization of PP/clay nanocomposites based on modified polypropylene and clay

X‐ray diffraction and differential scanning calorimeter (DSC) methods have been used to investigate the crystallization behavior and crystalline structure of hexamethylenediamine (HMDA)‐modified maleic‐anhydride‐grafted polypropylene/clay (PP‐g‐MA/clay) nanocomposites. These nanocomposites have been prepared by using HMDA to graft the PP‐g‐MA (designated as PP‐g‐HMA) and then mixing the PP‐g‐HMA polymer in hot xylene solution, with the organically modified montmorillonite. Both X‐ray diffraction data and transmission electron microscopy images of PP‐g‐HMA/clay nanocomposites indicate that most of the swellable silicate layers are exfoliated and randomly dispersed into PP‐g‐HMA matrix. DSC isothermal results revealed that introducing 5 wt % of clay into the PP‐g‐HMA structure causes strongly heterogeneous nucleation, which induced a change of the crystal growth process from a three‐dimensional crystal growth to a two‐dimensional spherulitic growth. Mechanical properties of PP‐g‐HMA/clay nanocomposites performed by dynamic mechanical analysis show significant improvements in the storage modulus when compared to neat PP‐g‐HMA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3242–3254, 2005     

Characterization of a Water-Dispersed Biodegradable Polyurethane-Silk Composite Sponge Using 13C Solid-State Nuclear Magnetic Resonance as Coating Material for Silk Vascular Grafts with Small Diameters

Recently, Bombyx mori silk fibroin (SF) has been shown to be a suitable material for vascular prostheses for small arteries. In this study, we developed a softer SF graft by coating water-dispersed biodegradable polyurethane (PU) based on polycaprolactone and an SF composite sponge on the knitted SF vascular graft. Three kinds of ¹³C solid-state nuclear magnetic resonance (NMR), namely carbon-13 (¹³C) cross-polarization/magic angle spinning (MAS), ¹³C dipolar decoupled MAS, and ¹³C refocused insensitive nuclei enhanced by polarization transfer (r-INEPT) NMR, were used to characterize the PU-SF coating sponge. Especially the ¹³C r-INEPT NMR spectrum of water-dispersed biodegradable PU showed that both main components of the non-crystalline domain of PU and amorphous domain of SF were highly mobile in the hydrated state. Then, the small-diameter SF artificial vascular grafts coated with this sponge were evaluated through implantation experiments with rats. The implanted PU-SF-coated SF grafts showed a high patency rate. It was confirmed that the inside of the SF grafts was covered with vascular endothelial cells 4 weeks after implantation. These results showed that the water-dispersed biodegradable PU-SF-coated SF graft created in this study could be a strong candidate for small-diameter artificial vascular graft.     

1H and 13C NMR study of the structure of α-lithio thiacylohexane 1-oxides: A planar metallated carbon

The lithiospecies deriving from the cis and trans 4-t-butyl thiacyclohexane 1-oxides are studied by ¹H and ¹³C NMR. Their structure is discussed mainly by examination of H-H and ^y13C-H coupling constants. Pyramidal α-sulfinyl carbanions are definitely rejected on the basis of these NMR data and half-chair structures with a planar metallated carbon are proposed.     

13C13C spin coupling constants in phenanthrene derivatives

The synthesis of six 1-X- (X = OH, OCH₃, OCOCH₃, CH₃, CHO and CN) phenanthrene derivatives with a ¹³C label at C-1 is described. An analysis of the ¹³C¹³C spin coupling constants shows the importance of π-interaction for the coupling constant transmission. Small ¹³C¹³C spin coupling constants over 6 bonds are reported.     

Der Einfluß von Hydroxylgruppen auf die Größe der13C,13C-Kopplungskonstanten

The¹³C,¹³C coupling constants of some alcohols with different structures were determined and the influence of hydroxyl groups on the magnitude of the coupling constants was evaluated by comparison of the data with the values obtained for the corresponding hydrocarbons. It is shown, that the introduction of a hydroxyl group in an organic molecule leads to an increase of the¹ J (CC) coupling constant of about 3 Hz.     

13C NMR spectroscopy of new amino protective groups

The ¹³C data of several new amino protecting groups of the urethane structure are reported. The speeds of acidolytic cleavage are correlated with the ¹³C parameters.     

The development of nuclear microprobe techniques for the spatial determination of13C and13C/12C ratios

Sensitive and selective nuclear reaction methods have been sought for the nuclear microprobe measurement of the spatial distributions of¹³C and¹³C/¹²C ratios. The¹³C(α, n)¹⁶O reaction, with neutron detection, is the most selective for¹³C, and has a sensitivity of ca. 100 ppm. The reactions¹³C(d, p)¹⁴C and¹²C(d, p)¹³C, with proton detection, are the most sensitive for the simultaneous measurement of¹³C and¹²C, with detection limits of 30 and 2 ppm respectively. Less sensitive alternative reaction pairs are;¹³C(³He, p)¹⁵N and¹²C(³He, p)¹⁴N;¹³C(d, nγ)¹⁴N and¹²C(d, pγ)¹³C;¹³C(³He, pγ)¹⁵N and¹²C(³He, pγ)¹⁴N. The conditions governing their use, particularly light element interferences, are detailed.