聚(L-谷氨酸)水凝胶介导羟基磷灰石的生物矿化

以1-乙基-3-(3-二甲基氨基丙基)碳二亚胺盐酸盐(EDC·HCl)为羧基活化剂, 己二酸二酰肼(ADH)为交联剂, 制备了生物活性聚(L-谷氨酸)(PLGA)水凝胶. 通过X射线衍射和扫描电子显微镜等表征了在不同浓度模拟体液(SBF)中羟基磷灰石(HA)的形成和生长. PLGA水凝胶的表面和内部均可观察到HA的形成和生长. 同时探讨了PLGA水凝胶矿化前后的力学性能. 将矿化前后PLGA水凝胶用于脂肪干细胞(ASCs)的培养, 研究其细胞相容性.     

Polyelectrolyte complexes of soluble poly-2-[(methacryloyloxy)ethyl]trimethylammonium chloride and its hydrogels with poly(acrylic acid)

The complex formation of poly-2-[(methacryloyloxy)-ethyl]trimethylammonium chloride (PMADQUAT) with poly(acrylic acid) (PAA) of different molecular weights has been studied in aqueous solutions by potentiometric, viscometric, turbidimetric and FTIR spectroscopic methods. The formation of insoluble non-stoichiometric polyelectrolyte complexes has been shown. The stability of polyelectrolyte complexes in solutions of different pH and ionic strength has been evaluated. The formation of polyelectrolyte complexes between hydrogels of PMADQUAT and linear PAA of different molecular weights has been studied. It was shown that the molecular weight of PAA considerably affects the kinetics of interaction as well as the final state of gel-polymer complex.     

Hydrophilic films based on poly(acrylic acid)–poly(vinyl methyl ether) blends cross-linked by gamma-radiation

Hydrophilic polymeric films based on blends of poly(acrylic acid) and poly(vinyl methyl ether) (PVME) were prepared by casting technique and were cross-linked by gamma-radiation. The films are soft and elastic in a dry state and form hydrogels upon immersion in water. Effect of absorbed dose on the gel fraction as well as on the swelling of the films in aqueous solutions of different pH is studied. It was found that addition of lower molecular weight PVME decreases the gelation dose, which is likely related to a decrease in glass transition temperature of the blends. In acidic media the films have low swelling degree because of suppression of carboxylic groups ionisation and formation of additional physical cross-links via interpolymer hydrogen bonding.     

Amphoteric poly(vinyl alcohol) gel as a force generator: Observation of microporous gel formation with cryo-SEM

Amphoteric PVA hydrogels were made from mixed aqueous solutions of poly(acrylic acid), poly(allylamine) hydrochloride and poly(vinyl alcohol) by repetitive freezing and thawing. The hydrogen bond induced gelation produced an elastic and tough microporous hydrogel which generated tension as high as 0.3MPa corresponding to the solvent exchange from water to acetone. In this paper we show the microscopic structure of hydrogels determined by means of cryo-SEM technique and X-ray analysis.     

Synthesis of cationic water‐soluble copolymers and hydrogels based on [2‐(methacryloyloxy)ethyl]trimethylammonium chloride and 2‐hydroxyethylacrylate and their complex formation with poly(acrylic acid)

Water‐soluble cationic copolymers and hydrogels were synthesized by radical copolymerization of [2‐(methacryloyloxy)ethyl]trimethylammonium chloride (MADQUAT) and 2‐hydroxyethylacrylate (HEA). The kinetics of copolymerization has been studied and the reactivity ratios were determined. It was found that MADQUAT exhibits higher reactivity in copolymerization. The complexation between linear MADQUAT‐HEA and linear poly(acrylic acid) (PAA) has been studied in aqueous solutions at different pH. It results in the formation of insoluble polyelectrolyte complexes, whose composition and stability to aggregate depends on MADQUAT content in copolymers and pH. The hydrogels were synthesized by three‐dimensional radical copolymerization of MADQUAT and HEA in the presence of a crosslinker. The effects of the feed mixture composition on yield and swelling properties of the hydrogels were studied. The interactions of these hydrogels with linear PAA result in formation of gel–polyelectrolyte complexes and contraction of the samples. It was found that the contraction depends on copolymer composition, PAA molecular weight, and solution pH. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44:845–853, 2006     

Adhesion properties of physically crosslinked elastic gels of poly(sodium acrylate)–poly(acrylic acid) mixtures evaluated by a point contact method

Adhesion properties of physically crosslinked hydrogels consisting of partially hydrated poly(sodium acrylate) (PSA) and poly(acrylic acid) (PAA) were investigated. The adhesion force and separation energy between the gels in swollen states were measured using a simple tack-evaluation technique by a point contact. As a result, the adhesion properties were significantly affected by the PSA/PAA ratio, which resulted from the fact that the physical and chemical properties of gels were changed through the replacement of PSA by PAA at gelation. The measurements of attenuated total reflectance Fourier transform infrared spectroscopy and the dynamic shear viscoelasticity suggested that the number of nonionized carboxyl groups increased and the stiffness increased with increasing the PAA ratio, respectively. In order to understand the adhesion properties further, the apparent contact area was evaluated by a stamp experiment using vermilion ink. The relationships between the adhesion properties and the physical and chemical features of gels are discussed in terms of the surface molecular interaction, the elastic and viscous properties of the bulk, and the apparent and true contact areas of the present system. From these results, the factors that determine the adhesion curve and the uniqueness and advantages of the present evaluation method are clarified.     

Sol‐gel transition behavior of amphiphilic comb‐like poly[(PEG‐b‐PLGA)acrylate] block copolymers

The effects of comb‐like amphiphilic block copolymer architectures on the physical properties such as sol‐gel transition and micellization behaviors with the change of temperature and pH were examined. Comb‐like poly((poly(ethylene glycol)‐b‐(poly(lactic acid‐co‐glycolic acid))acrylate‐co‐acrylic acid) (poly((PEG‐b‐PLGA)A‐co‐AA)) copolymers were synthesized by coupling of poly(acrylic acid) (PAA) with two different kinds of PEG‐b‐PLGA diblock copolymers to investigate the effects of the number of branches and hydrophilicity/hydrophobicity on the sol‐gel transition and micellization. The molecular weights and chemical structures were confirmed by GPC and ¹H NMR. The number of PEG‐b‐PLGA branches was gradually deviated from the feed molar ratio with increasing the molecular weight and the number of branches and due to the bulkiness of PEG‐b‐PLGA. Poly[(PEG‐b‐PLGA)A‐co‐AA] aqueous solutions showed thermosensitive sol‐gel transition behavior, and the gelation took place at lower concentration with increasing the number of branches and PLGA chain length due to the increase of hydrophobicity. The temperature, at which abrupt increase of viscosity by dynamic rheometer appeared, was also in good agreement with sol‐gel transition by tube‐titling method. The CMC, calculated from UV‐Visible spectroscopy using DPH as hydrophobic dye, also decreased with increasing the number of PEG‐b‐PLGA branches and PLGA chain length with same reason. The micelle size was increased with increasing temperature at the initial stage, however, decreased with further increase of temperature, since the micelles were, first, aggregated by hydrophobic intermolecular interaction, and then fragmented by dehydration of PEG segments with increasing temperature. PH‐sensitive PAA backbone played a key role in physical properties. With decreasing pH, sol‐to‐gel transition temperature, CMC values, and micelle size were decreased because of the increase of hydrophobicity resulting form non‐ionized acrylic acid. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1287–1297, 2010     

PH effects in the complex formation and blending of poly(acrylic acid) with poly(ethylene oxide)

The effect of pH on the complex formation between poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO) has been studied in aqueous solutions by turbidimetric and fluorescent methods. It was shown that the formation of insoluble interpolymer complexes is observed below a certain critical pH of complexation (pH(crit1)). The formation of hydrophilic interpolymer associates is possible above pH(crit1) and below a certain pH(crit2). The effects of polymer concentrations in solution and PEO molecular weight as well as inorganic salt addition on these critical pH values were studied. The polymeric films based on blends of PAA and PEO were prepared by casting from aqueous solutions with different pHs. These films were characterized by light transmittance measurements and differential scanning calorimetry. The existence of the pH value above which the polymers form an immiscible blend was demonstrated. The transitions between the interpolymer complex, miscible blend, and immiscible blend caused by pH changes are discussed. The recommendations for preparation of homogeneous miscible films based on compositions of poly(carboxylic acids) and various nonionic water-soluble polymers are presented.     

Toughening hydrogels by immersing with oppositely charged polymers

A very simple yet novel strategy to significantly enhance the mechanical properties of hydrogels is reported. Poly(acrylic acid) (PAA) hydrogels with aligned macroporous channels are immersed in the aqueous solutions of poly(dimethyl diallyl ammonium chloride) (PDMDAAC). Strong electrostatic interactions are formed between the anionic PAA and cationic PDMDAAC chains. In the resultant PAA/PDMDAAC hybrid hydrogels, the mass ratio of PDMDAAC to PAA is about 0.2 and PDMDAAC is uniformly distributed throughout the gels. The mechanical properties of the formed hybrid hydrogels are largely enhanced in comparison with the original PAA hydrogels. The hybrid hydrogels exhibit high tensile strengths (0.38–1.73 MPa), elastic moduli (0.21–1.59 MPa) and toughness (up to 3.0 MJ/m³), about several to more than 10 times those of the corresponding PAA hydrogels. In addition, the PAA/PDMDAAC hydrogels also show excellent and very rapid shape recovery ability in both air and deionized water. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2432–2441     

Polyelectrolyte complexes of linear copolymers and hydrogels based on 2‐[(methacryloyloxy)ethyl]trimethylammonium chloride and N‐isopropylacrylamide

The formation of polyelectrolyte complexes of linear copolymers and hydrogels based on copolymers of 2‐[(methacryloyloxy)ethyl]trimethylammonium chloride with N‐isopropylacrylamide (MADQUAT–NIPAAM) and poly(acrylic acid) (PAA) has been studied. The composition of the copolymer has been found to affect the composition of the polyelectrolyte complexes significantly, and the molecular weight of PAA influences their aggregation stability. Hydrogels of MADQUAT–NIPAAM immersed in solutions of PAA undergo contraction because of the formation of gel–polymer complexes. The rate of contraction and the final swelling degree of the gel–polymer complexes depend on the concentration of PAA in solution and its molecular weight. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1506–1513, 2004     

Self-Forming Norbornene-Tetrazine Hydrogels with Independently Tunable Properties

Although photopolymerization reactions are commonly used to form hydrogels, these strategies rely on light and may not be suitable for delivering therapeutics in a minimally invasive manner. Here, hyaluronic acid (HA) macromers are modified with norbornene (Nor) or tetrazine (Tet) and upon mixing click into covalently crosslinked Nor-Tet hydrogels via a Diels–Alder reaction. By incorporating a high degree of Nor and Tet substitution, Nor-Tet hydrogels with a broad range in elastic moduli (5 to 30 kPa) and fast gelation times (1 to 5 min) are achieved. By pre-coupling methacrylated HANor macromers with thiolated peptides via a Michael addition reaction, Nor-Tet hydrogels are peptide-functionalized without affecting their physical properties. Mesenchymal stem cells (MSCs) on RGD-functionalized Nor-Tet hydrogels adhere and exhibit stiffness-dependent differences in matrix mechanosensing. Fluid properties of Nor-Tet hydrogel solutions allow for injections through narrow syringe needles and can locally deliver viable cells and peptides. Substituting HA with enzymatically degradable gelatin also results in cell-responsive Nor-Tet hydrogels, and MSCs encapsulated in Nor-Tet hydrogels preferentially differentiate into adipocytes or osteoblasts, based on 3D cellular spreading regulated by stable (HA) and degradable (gelatin) macromers.     

改性纳米羟基磷灰石/PLGA复合材料的制备及生物活性

以低聚乳酸接枝改性的羟基磷灰石纳米粒子(op-HA)和聚丙交酯-乙交酯(PLGA)制备的生物可降解纳米复合材料(op-HA/PLGA)为研究对象, 采用FTIR, TGA, ESEM和EDX分析其接枝反应、接枝率、表面形貌和钙磷沉积情况, 通过在材料膜表面接种兔成骨细胞进行体外培养, 采用荧光染色、NIH Image J图像分析和Real-time PCR综合评价细胞在材料表面的形态、黏附面积比、增殖能力和基因表达水平, 以此评价新型骨修复纳米复合材料op-HA/PLGA的表面性质和生物活性. 研究结果表明, op-HA的表面接枝率为8.3%, 掺入至PLGA后可形成富含钙磷的粗糙表面, 促进成骨细胞的黏附、扩展和增殖, 提高Ⅰ型胶原蛋白(Collagen-Ⅰ)、骨形态蛋白-2(BMP-2)和骨连接蛋白(Osteonectin)的基因表达水平, 提高材料的钙磷沉积能力. op-HA/PLGA具有良好的细胞相容性和成骨活性.     

Complexation between poly(acrylic acid) and poly(vinylpyrrolidone): Influence of the molecular weight of poly(acrylic acid) and small molecule salt on the complexation

Poly(acrylic acid) (PAA) with different molecular weight and poly(vinylpyrrolidone) (PVP) were prepared by free radical polymerization using 2,2′-azoisobutyronitrile (AIBN) as initiator in anhydrous methanol for PAA, and in distilled water for PVP. Then, the complexation between PAA and PVP in aqueous solution was studied by UV transmittance measurement and fluorescence probe technique. The result shows that (1) at low pH, the formation of complexation between PAA and PVP bases on the intermacromolecular hydrogen bond and the composition of the formed complex is around 3:2 (the unit molar ratio of PAA to PVP) at pH 2.60 over the range of pH investigated. (2) The cooperative interaction through the formation of hydrogen bond among active sites plays an important role in complex formation, and depends on the pH of solution, the required minimum chain length of poly(acrylic acid). (3) The hydrogen bond is not affected by small molecular salt, which only affects those carboxylic groups without forming hydrogen bond on the PAA chain.     

聚L-谷氨酸可注射水凝胶的制备及性能

通过活化改性聚L-谷氨酸（PLGA）制备酰肼化PLGA（PLGA-ADH）和3-氨基-1,2-丙二醇改性的PLGA（PLGA-OH）,PLGA-OH经高碘酸钠氧化制得醛基化PLGA（PLGA-CHO）,以PLGA-ADH和PLGA-CHO为前驱体,通过席夫碱交联反应构建了PLGA可注射水凝胶.研究了酰肼化和醛基化改性前后PLGA的结构变化,考察了固含量对水凝胶成胶时间、溶胀行为、机械性能、体外降解性能、药物释放行为及微观形貌等的影响,并进行了初步的细胞培养实验及裸鼠皮下注射成胶实验.结果表明,该PLGA可注射水凝胶在组织工程领域具有良好的应用前景.     

Interpolymer complex between poly(ethylene oxide) and poly(carboxylic acid)

An interpolymer complex was prepared by mixing aqueous solutions of poly(ethylene oxide) (PEO) and of a poly(carboxylic acid), i.e., poly(acrylic acid)(PAA), poly(methacrylic acid)(PMAA), or styrene-maleic acid copolymer(PSMA). The complexation mechanism was discussed on the basis of results of such experimental methods as viscosity, potentiometric titration, and turbidimetry. The hydrogen bond is primarily involved in these complexations, but the influence of hydrophobic interaction on complexation can not be ignored. If the degree of dissociation α of carboxylic acid or the degree of polymerization P_n of PEO was perceptibly changed, a stable complex was obtained at about α 0.1 or P_n (PEO) = 40 for PMAA, 200 for PAA. This fact indicates that more than a definite number of binding sites are necessary for a stable interpolymer complex to be formed and that cooperative interaction among active sites plays an important role in complex formation.     

Poly(N-isopropylacrylamide-co-N-t-butylacrylamide)-block-poly(ethylene glycol)-block-poly(N-isopropylacrylamide-co-N-t-butylacrylamide) triblock copolymers: synthesis and thermogelation properties of aqueous solutions

Novel triblock copolymers with PEG middle blocks of 1–10 kDa and poly(N-isopropylacrylamide-co-t-butylacrylamide) statistical copolymer side arms with DP_n?≈?88 and different compositions, were synthesized by SET-LRP. The thermogelation properties of their aqueous solutions depended on both hydrophobic monomer content of the side blocks and molecular weight (MW) of the poly(ethylene glycol) (PEG) middle block, as proven by dynamic rheometry, DSC, and tube inversion method measurements. At constant PEG chain length, increasing TBAM proportions led to a gelation process occurring at progressively lower temperatures, as well as to a lower stability of the forming hydrogels in the case of shorter-PEG-chain block copolymers. By employing longer PEG blocks (M_PEG ≥6,000 Da), stable hydrogels with the gelation temperature below 37 °C could be obtained. For a constant composition of the copolyacrylamide blocks, the dependence of the phase transition temperature (T_ph) on M_PEG displayed a different shape at different polymer solution concentrations, because of the stronger variation of T_ph with polymer concentration as M_PEG increased. Also, the viscoelastic properties of the hydrogels resulting from 20 wt.% polymer aqueous solutions at 37 °C were stronger affected by the MW of the PEG middle block than by the hydrophobic character of the thermosensitive side blocks.     

Fabrication of hollow porous PLGA microspheres for controlled protein release and promotion of cell compatibility

This letter reports on the fabrication of hollow,porous and non-porous poly(D,L-lactide-co-glycolide) (PLGA) microspheres(MSs) for the controlled release of protein and promotion of cell compatibility of tough hydrogels.PLGA MSs with different structures were prepared with modified double emulsion methods,using bovine serum albumin(BSA) as a porogen during emulsification.The release of the residual BSA from PLGA MSs was investigated as a function of the MS structure.The hollow PLGA MSs show a faster protein release than the porous MSs,while the non-porous MSs have the slowest protein release.Compositing the PLGA MSs with poly(vinyl alcohol)(PVA) hydrogels promoted chondrocyte adhesion and proliferation on the hydrogels.     

Application of sensitive hydrogels in chemical and pH sensors

In the present work, pH-sensitive poly(vinyl alcohol)/poly(acrylic acid) (PVA/PAA) blends as well as hydrogels based on poly(N-isopropylacrylamide) (PNIPAAm), which are sensitive to organic solvent concentration in aqueous solutions, were used in silicon micromachined sensors. A sensitivity of approximately 15 mV/pH was obtained for a pH sensor with a 50 μm thick PVA/PAA hydrogel layer in a pH range above the acid exponent of acrylic acid (pK_a=4.7). The output voltage versus pH-value characteristics and the long-term signal stability of hydrogel-based sensors were investigated and the measurement conditions necessary for high signal reproducibility were determined. The influence of the preparation conditions of the hydrogel films on the sensitivity and response time of the chemical and pH sensors is discussed.     

Polyelectrolyte multilayers on wood fibers: influence of molecular weight on layer properties and mechanical properties of papers from treated fibers

This paper compares the influence of the molecular weight of polylelectrolytes forming polyelectrolyte multilayers (PEM) on wood fibers on adhesion and paper strength. Sheets were made from fibers treated with poly(allylamine hydrochloride) (PAH)/poly(acrylic acid) (PAA) of molecular mass 70,000 and 240,000, respectively, and of poly(dimethyldiallylammonium chloride) (PDADMAC)/poly(styrene sulfonate) (PSS) of molecular mass 30,000 and 80,000, respectively. The results were compared to what has recently been reported for PEM formation on fibers using a low-molecular-mass combination of PAH and PAA and a high-molecular-mass combination of PDADMAC/PSS. There was a less significant improvement in the case of the low-molecular-mass PDADMAC/PSS and the high-molecular-mass PAH/PAA. The adsorbed amounts of PAH and PDADMAC were also determined, showing a lower adsorbed amount of the low-molecular-mass PAH than of the high-molecular-mass PDADMAC. The amount of low-molecular-mass PDADMAC was similar to that found for high-molecular-mass PDADMAC/PSS. Individual fibers were partly treated and studied, showing a less significant decrease in wettability with low-molecular-mass PDADMAC/PSS than with the high-molecular-mass combination. The effect of the molecular weight on the adhesion was discussed in terms of the structure and wettability of the PEMs.     

A Way to Prepare Core‐Shell Biocompatible Polymeric Nano‐Particles from Gelatin and Acrylic Acid

Narrowly distributed core‐shell nano‐particles at relatively high concentration (30 mg/mL) were prepared via in situ polymerization of acrylic acid in an aqueous solution of biocompatible gelatin. These polymeric nano‐particles, in aqueous solution, had cores mainly comprised of an insoluble inter‐polymer complex of poly(acrylic acid, PAA) and gelatin and shells comprised of soluble gelatin (denoted as gelatin/PAA nano‐particles). Dynamic light scattering and electrophoretic light scattering techniques were used to trace the in situ polymerization process. The structure of the gelatin/PAA nano‐particle was further locked‐in via shell crosslinking; i.e., the reaction between glutaraldehyde and gelatin. Scanning force microscopy (SFM) was used to observe the morphologies of the particles before and after cross‐linking. Furthermore, the pH responsive behaviors of the gelatin/PAA nano‐particles before and after shell crosslinking were studied.