Self-assembled,wormlike-cylinder network of polystyrene-block-poly(ethylene oxide) micelles in solution

We report the formation of a highly entangled and interconnected, self-assembled, wormlike-cylinder network of polystyrene-block-poly(ethylene oxide) in N, N-dimethylformamide/water. In this system, N,N-dimethylformamide was a common solvent and water was a selective solvent for the poly(ethylene oxide) blocks. The degrees of polymerization of the polystyrene and poly(ethylene oxide) blocks were 962 and 227, respectively. The network was formed at copolymer concentrations higher than 0.4 wt % and consisted of self-assembled, wormlike cylinders that were interconnected by Y-shaped, T-shaped, and multiple junctions. The network morphology was visualized with transmission electron microscopy. Capillary viscometry measurements revealed an order-of-magnitude increase in the inherent viscosity of the colloidal system upon the formation of the network. A similar effort to obtain a wormlike-cylinder network in an N,N-dimethylformamide/acetonitrile system, in which acetonitrile was a selective solvent for the poly(ethylene oxide) blocks, was unsuccessful even at high copolymer concentrations; instead, the wormlike cylinders showed a tendency to align. The viscosity measurements also did not show a substantial increase in the inherent viscosity. Thus, the solvent played a critical role in determining the formation of the self-assembled, wormlike-cylinder network. This formation of the network resulted from an interplay between the end-capping energy, bending energy (curvature), and configurational entropy of the self-assembled, wormlike-cylinder micelles that minimized the free energy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3605–3611, 2006     

Temperature-induced reversible morphological changes of polystyrene-block-poly(ethylene oxide) micelles in solution

Temperature-induced reversible morphological changes of polystyrene-block-poly(ethylene oxide) micelles with degrees of polymerization of 962 for the PS and 227 for the PEO blocks (PS962-b-PEO227) in N,N-dimethylformamide (DMF)/water, in which water is a selective solvent for the PEO block, were observed. For a system with 0.2 wt % copolymer concentration and 4.5 wt % water concentration in DMF/water, the micelle morphology observed in transmission electron microscopy changed from vesicles at room temperature to worm-like cylinders and then to spheres with increasing temperature. Mixed morphologies were also formed in the intermediate temperature regions. Cooling the system back to room temperature regenerated the vesicle morphology, indicating that the morphological changes were reversible. No hysteresis was observed in the morphological changes during heating and cooling. Dynamic light scattering revealed that the hydrodynamic radius of the micelles decreased with increasing temperature. Combined static and dynamic light scattering results supported the change in morphology with temperature. The critical micellization temperatures and critical morphological transition temperatures were determined by turbidity measurements and were found to be dependent on the copolymer and water concentrations in the DMF/water system. The morphological changes were only possible if the water concentration in the DMF/water system was low, or else the mobility of the PS blocks would be severely restricted. The driving force for these morphological changes was understood to be mainly a reduction in the free energy of the corona and a minor reduction in the free energy of the interface. Morphological observations at different time periods of isothermal experiments indicated that in the pathway from one equilibrium morphology to another, large compound micelles formed as an intermediate or metastable stage.     

Reversible aggregation of polystyrene-block-poly(2-vinylpyridine)-block-poly(ethylene oxide) block copolymer micelles in acidic aqueous Solutions

Micelles of polystyrene-block-poly(2-vinylpyridine)-block-poly(ethylene oxide) (PS-PVP-PEO) were studied in acidic aqueous solutions by static and dynamic light scattering, alkalimetric titration, fluorescence correlation spectroscopy, and after deposition on a mica surface by atomic force microscopy. The PS-PVP-PEO micelles prepared by dialysis in ternary 1,4-dioxane-methanol-acidic water mixtures have a very low association number and show a strong tendency to form aggregates. The aggregation, which is promoted at low pH, seems to be fully reversible. Possible mechanisms of the aggregation are discussed. Atomic force microscopy scans of PS-PVP-PEO micelles deposited on a mica surface reveal the formation of micellar aggregates and support the general concept of aggregation upon changes in conditions and deterioration of the stability of small micelles.     

Structure and thermodynamics of polystyrene-block-poly(ethylene/propene) micelles in selective solvents

The concentration and temperature dependencies of micelle formation by a polystyrene-block-poly(ethylene/propene) copolymer in several ketones (2-butanone, 3-pentanone, 4-methyl-2-pentanone, 4-heptanone, 5-methyl-2-hexanone and 5-methyl-3-heptanone) were studied by static and dynamic light scattering, viscometry and size exclusion chromatography. No micelles were detected in solutions of 5-methyl-3-heptanone. The standard Gibbs energy, ΔG°, the standard enthalpy, ΔH°, and the standard entropy, ΔS°, of micellization were estimated. The values of ΔG° and ΔH° were negative for all ketones studied and depended on the polar character of the ketone. The micelles showed larger association numbers and densities independent of the ketone. Micelle dimensions hardly depended on the ketone.     

Hydrolytic degradation of poly(ethylene oxide)-block-polycaprolactone worm micelles

Spherical micelles and nanoparticles made with degradable polymers have been of great interest for therapeutic application, but degradation-induced changes in a spherical morphology can be subtle and mechanism/kinetics appears poorly understood. Here, we report the first preparation of giant and flexible worm micelles self-assembled from degradable copolymer poly(ethylene oxide)-block-polycaprolactone. Such worm micelles spontaneously shorten to generate spherical micelles, triggered by polycaprolactone hydrolysis, with distinct mechanism and kinetics from that which occurs in bulk material.     

Metallo‐supramolecular micelles: Studies by analytical ultracentrifugation and electron microscopy

In aqueous solutions, amphiphilic block copolymers in which a polystyrene (PS) segment is connected to a poly(ethylene oxide) (PEO) block via a bis(2,2′:6′,2″‐ terpyridine ruthenium) complex can form micelles. Such micelles of the protomer type PS₂₀‐[Ru]‐PEO₇₀, according to the preparation procedure representing frozen micelles, were studied by sedimentation velocity and sedimentation equilibrium analysis in an analytical ultracentrifuge and by transmission electron microscopy, with different techniques applied for the sample preparation. The particles obtained were surprisingly multifarious in size. In ultracentrifugation experiments performed at relatively low salt concentrations, the distributions of the sedimentation coefficient s_20,w showed a pronounced peak at 9.6 S and a broad, only partly separated second peak around 14 S. The molar mass of the particles at the peak was around 430,000 g/mol, corresponding to an aggregation number of approximately 85. The average hydrodynamic diameter of the particles in the peak fraction was approximately 13 nm. In electron micrographs of negatively stained samples, spheres of diameters between 10 and 25 nm were the most abundant particles, but larger ones with a wide size range were also visible. The latter particles apparently were composed of smaller ones. The data from both sedimentation analysis and electron microscopy showed that (1) the studied compound formed primary micelles of diameters around 20 nm and (2) the primary micelles had a tendency toward aggregation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3159–3168, 2003     

Effect of water content on the size and membrane thickness of polystyrene-block-poly(ethylene oxide) vesicles

The asymmetric amphiphilic block copolymer polystyrene962-block-poly(ethylene oxide)227(PS962-b-PEO227) canforms micelles with N, N-dimethylformamide(DMF) as co-solvent and water as selected solvent, and when the water content of the mixed solvent is higher than 4.5 wt%, the vesicle will be dominated. This work finds that once vesicles are formed in the DMF-water mixed solvent, the vesicle size and membrane thickness can be tuned by further increasing water content. As the water fraction elevated from 4.8 wt% to 13.0 wt%, the vesicle size dercreases from 246 nm to 150 nm, while the membrane thickness increases from 28 nm to 42 nm. In addition, the block copolymer packing and the free energy are analyzed as the vesicle size becomes small and the membrane becomes thick.     

Morphology of single-chain single crystals of poly(ethylene oxide)

Single-chain particles of poly(ethylene oxide) (PEO) were prepared by spreading a 10^-4 wt.-% solution of PEO in benzene on a hot water surface. After isothermal crystallization at 317,2 ± 0,1 K for 10 h, regular-shaped single-chain crystals were observed. A variety of typical morphologies were also found, and some of them are discussed on the basis of the habit of PEO crystals and various twin modes.     

Structural studies of radiation-crosslinked poly(ethylene oxide)

The structure and thermal behavior of freeze-dried gels of radiation-crosslinked high molecular weight poly(ethylene oxide) (PEO) were investigated by optical and electron microscopy, wide-angle x-ray scattering (WAXS), DTA, TGA, and thermomechanical analysis. The gels are highly porous with thin crystalline walls. Small spherulite and hedrite structures are observed on the walls. A model for gel formation in solution is suggested. A statistically homogenous chemical network is formed as a result of intrachain and interchain crosslinking. Simultaneous grafting of macromolecular fragments formed by chain scission also occurs. On increasing the irradiation dose from 1 to 15 Mrad, the degree of crystallinity determined by x-ray diffraction and the total intensity of diffraction gradually decrease. The temperature and enthalpy of melting diminish steeply up to 5 Mrad, fall only slightly from 5 to 8 Mrad, and do not change from 8 to 15 Mrad. By comparing the x-ray and DTA crystallinity values, this is shown to be due not only to reduced crystallinity at higher network density but also to Tree energy changes of entropic origin in crystalline and amorphous regions. Radiation chemical yields, G(-units), for these dose ranges are 100, 38, and 0, respectively. Thermomechanical analysis was used to determine the elastic modulus of compression as a function of the dose absorbed, and the average molecular weight of network chains was estimated. decreases with doses up to 10 Mrad and does not change with further irradiation.     

Morphology of poly(ethylene oxide)/poly(vinyl acetate) blends

The morphology of poly(ethylene oxide)/poly(vinyl acetate) (PEO/PVAc) blends was examined using small angle X-ray scattering (SAXS) and optical microscopy. The morphological and structural parameters of the blends are dependent on both composition and crystallization conditions. Optical microscopy revealed that blend samples prepared by solution casting crystallized with volume-filling crystals up to a composition of 30/70 wt% PEO/PVAc; at higher PVAc content there was no evidence of crystallization in the temperature range studied. Pure PEO always crystallized with a spherulite-hedrite morphology. The formation of spherulites was relatively favoured at lower crystallization temperatures and by addition of PVAc to PEO. Small angle X-ray intensity profiles were analyzed using a recently developed methodology and it was found that, for a given crystallization temperature, the amorphous and interphase thicknesses increased with increasing PVAc content but that the average crystalline thickness was independent of composition. The morphological and structural properties of the PEO/PVAc blends were attributed to the presence of non-crystallizable material in both the interlamellar and interfibrillar regions.     

Morphology and interpenetrated growth of spherulites in miscible poly(ethylene succinate)/poly(ethylene oxide) blends

Morphology development and growth process of spherulites in miscible poly(ethylene succinate)/poly(ethylene oxide) blends are studied by means of polarizing optical microscopy and atom force microscopy in this paper. Thin films with different film thicknesses were used to follow the growth processes of spherulites and dendrites. It is shown that, when one component spherulite grows, the other component in the melt is always excluded from the spherulite. The excluded component may reenter into the spherulite through diffusion depending on amorphous volume fraction of spherulite and segmental mobility of molecules, which leads to the occurrence of interpenetrated growth. This mechanism was analyzed in detail in this paper.     

Poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide)-g-poly(vinyl pyrrolidone): synthesis and characterization

Pluronic poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide) (PEO-PPO-PEO) block copolymers are grafted with poly(vinyl pyrrolidone) by free radical polymerization of vinyl pyrrolidone with simultaneous chain transfer to the Pluronic in dioxane. This modified polymer has both thermal responsiveness and remarkable capacity to interact with a wide variety of hydrophilic and hydrophobic pharmaceutical agents which is very attractive for medical applications. The chemical structure of the graft copolymers was characterized by FTIR and 1H NMR spectroscopy. Polymerization conditions such as initiators, feed ratio, and reaction times are studied to obtain the ideal graft copolymer.     

Morphology of ultrathin polymer films based on poly(ethylene oxide) blends

The structure of ultrathin (15–200 nm) films of two types prepared from polymer blends based on PEO (the crystallizable component), namely, PEO-poly(arylene sulfone oxide) (the amorphous component) and PEO-PB (the amorphous component), has been studied by atomic force microscopy. The content of PEO in both blends is 76 wt %. Ultrathin blend films have been applied on a Si substrate via substrate dipping into dilute solutions of polymer blends in chloroform at room temperature. The rate of the substrate lift has been varied from 0.1 to 1 mm/min. The amorphous-amorphous separation takes place during formation of ultrathin films of the above blends in the course of the substrate lift at the stage of gelation. The crystallization of PEO and dewetting in the resulting two-phase blend gels depend on the rate of the substrate lift and the rigidity of macromolecules of the amorphous component. Moreover, the predominant interaction of the substrate with one of the components plays a significant role in structure formation of ultrathin films of both polymer blends.     

Characterization and demulsification of poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) copolymers

Four poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) copolymers with different molecular weights and PPO/PEO composition ratios were synthesized. The characterization of the PEO-PPO-PEO triblock copolymers was studied by surface tension measurement, UV-vis spectra, and surface pressure method. These results clearly showed that the CMC of PEO-PPO-PEO was not a certain value but a concentration range, in contrast to classical surfactant, and two breaks around CMC were reflected in both surface tension isotherm curves and UV-vis absorption spectra. The range of CMC became wider with increasing PPO/PEO composition ratio. Surface pressure Pi-A curves revealed that the amphiphilic triblock copolymer PEO-PPO-PEO molecule was flexible at the air/water interface. We found that the minimum area per molecule at the air/water interface increased with the proportion of PEO chains. The copolymers with the same mass fractions of PEO had similar slopes in the isotherm of the Pi-A curve. From the demulsification experiments a conclusion had been drawn that the dehydration speed increased with decreased content of PEO, but the final dehydration rate of four demulsifiers was approximate. We determined that the coalescence of water drops resulted in the breaking of crude oil emulsions from the micrograph.     

Loading and release mechanisms of a biocide in polystyrene-block-poly(acrylic acid) block copolymer micelles

The kinetics of loading of polystyrene197-block-poly(acrylic acid)47 (PS197-b-PAA47) micelles, suspended in water, with thiocyanomethylthiobenzothiazole biocide and its subsequent release were investigated. Loading of the micelles was found to be a two-step process. First, the surface of the PS core of the micelles is saturated with biocide, with a rate determined by the transfer of solid biocide to micelles during transient micelle-biocide contacts. Next, the biocide penetrates as a front into the micelles, lowering the Tg in the process (non-Fickian case II diffusion). The slow rate of release is governed by the height of the energy barrier that a biocide molecule must overcome to pass from PS into water, resulting in a uniform biocide concentration within the micelle, until Tg is increased to the point that diffusion inside the micelles becomes very slow. Maximum loading of biocide into micelles is approximately 30% (w/w) and is achieved in 1 h. From partition experiments, it can be concluded that the biocide has a similar preference for polystyrene as for ethylbenzene over water, implying that the maximum loading is governed by thermodynamics.     

AFM study of micelle chaining in surface films of polystyrene-block-poly(ethylene oxide) stars at the air/water interface

A series of three-arm star block copolymers were examined using atomic force microscopy (AFM). These stars consisted of a polystyrene core composed of ca. 111 styrene units/branch with poly(ethylene oxide) (PEO) chains at the star periphery. Each star contained different amounts of PEO, varying from 107 to 415 ethylene oxide units/branch. The stars were spread as thin films at the air/water interface on a Langmuir trough and transferred onto mica at various surface pressures. Circular domains representing 2D micelle-like aggregated molecules were observed at low pressures. Upon further compression, these domains underwent additional aggregation in a systematic manner, including micellar chaining. At this point, domain area and the number of molecules/domain increased with increasing pressure. In addition, it was found that longer PEO chains led to greater intermolecular separation and less aggregation. These AFM results correspond to attributes seen in the surface pressure-area isotherms of the stars. In addition, they demonstrate the viability of AFM as a quantitative characterization technique.     

Miscibility of poly(ethylene oxide) with poly(N-vinyl pyrrolidone): DMTA and DTA studies

Dynamic mechanical thermal analysis and calorimetric studies are reported on blends of poly(ethylene oxide) (PEO) with poly(N-vinyl pyrrolidone) (PVP) between 80% and 40% PEO. DMTA curves show a peak corresponding to a phase of pure PEO and another peak which can be attributed to blended material. The calorimetric analysis shows an appreciable melting point depression and a marked decrease in the crystallization rate as the PVP content increases. The melting point depression follows the Nishi-Wang equation, giving an interaction parameter of ?0.50. These studies suggest the existence of microphases in the blend.     

Assessment of the integrity of poly(caprolactone)-b-poly(ethylene oxide) micelles under biological conditions: a fluorogenic-based approach

The integrity of block copolymer micelles is important for their effectiveness and successful delivery of the incorporated drugs. Here we evaluate the integrity of poly(caprolactone)-b-poly(ethylene oxide) micelles in media of varying chemical complexity and in cells by using fluorogenic micelles. Fluorogenic dye fluorescein-5-carbonyl azide diacetate was covalently attached to the micelle-core-forming part of the block copolymer, poly(caprolactone). The fluorescence was not detectable unless the poly(caprolactone)21-b-poly(ethylene oxide)45 micelles were destroyed and the fluorogenic dye was activated by deesterification. The fluorescence of the activated dye from destroyed micelles was easily detectable in various media and in cells. Micelles were stable in simple media such as phosphate-buffered saline but disassembled to varying extents with increasing chemical complexity of the media and addition of serum. The integrity of the internalized micelles within the cells showed a time-dependent decrease but remained largely preserved (80%) after 20 h of incubation with cells. A proof of principle was also demonstrated in vivo in mice. The fluorogenic approach to micelle integrity assessment presented herein should lend itself to other block copolymer micelles and assessments of their integrity in complex biological systems in vitro and in vivo.     

Poly(ethylene oxide)-poly(styrene oxide)-poly(ethylene oxide) copolymers: Micellization, drug solubilization, and gelling features

Two new poly(ethylene oxide)-poly(styrene oxide) triblock copolymers (PEO-PSO-PEO) with optimized block lengths selected on the basis of previous studies were synthesized with the aim of achieving a maximal solubilization ability and a suitable sustained release, while keeping very low material expense and excellent aqueous copolymer solubility. The self-assembling and gelling properties of these copolymers were characterized by means of light scattering, fluorescence spectroscopy, transmission electron microscopy, and rheometry. Both copolymers formed spherical micelles (12-14 nm) at very low concentrations. At larger concentration (>25 wt%), copolymer solutions showed a rich phase behavior, with the appearance of two types of rheologically active (more viscous) fluids and of physical gels depending on solution temperature and concentration. The copolymer behaved notably different despite their relatively similar block lengths. The ability of the polymeric micellar solutions to solubilize the antifungal drug griseofulvin was evaluated and compared to that reported for other structurally-related block copolymers. Drug solubilization values up to 55 mg g⁻¹ were achieved, which are greater than those obtained by previously analyzed poly(ethylene oxide)-poly(styrene oxide), poly(ethylene oxide)-poly(butylene oxide), and poly(ethylene oxide)-poly(propylene oxide) block copolymers. The results indicate that the selected SO/EO ratio and copolymer block lengths were optimal for simultaneously achieving low critical micelle concentrations (cmc) values and large drug encapsulation ability. The amount of drug released from the polymeric micelles was larger at pH 7.4 than at acidic conditions, although still sustained over 1 day.