多壁碳纳米管负载TiO_2复合器件可见光光催化降解RhB

采用溶胶-凝胶法制备了多壁碳纳米管(MWCNTs)负载的ITO/MWCNTs-TiO2/ITO复合器件,利用SEM、XPS、UV-Vis光谱等技术对复合样品进行形貌和结构表征,以液相罗丹明B(RhB)的可见光光催化降解为探针反应,评价MWCNTs-TiO2复合薄膜的催化活性.XPS结果表明MWCNTs与TiO2之间没有形成Ti-C键.I-V特性表明负载了MWCNTs的ITO/MWCNTs-TiO2/ITO复合器件的光电流增强.与空白TiO2薄膜相比,MWCNTs-TiO2复合薄膜的可见光光催化降解RhB的速率提高了3.2倍.MWCNTs并没有掺杂到TiO2晶格中,而是起到了类似光敏剂的作用,可在可见光激发下将导带电子转移到TiO导带上,经一系列反应降解RhB有机物.     

Zr改性MnO_x/MWCNTs催化剂的结构特征与低温SCR活性

以ZrO(NO3)2·2H2O为前驱体对多壁碳纳米管(MWCNTs)进行了改性并负载MnOx制备了MnOx/ZrO2/MWCNTs催化剂.考察了Zr对催化剂低温选择性催化还原(SCR)反应活性的影响,并通过多种分析手段对催化剂的结构进行了表征.结果表明Zr的添加对催化剂的低温SCR活性具有显著的促进作用,当Zr负载量为30%时,催化剂活性最佳.X射线衍射(XRD)、拉曼(Raman)光谱、透射电镜(TEM)、N2吸附-脱附的表征结果分析表明,适量的Zr改性促进了MnOx在载体表面的分散,增强金属氧化物与MWCNTs之间的作用,也能增加催化剂的比表面积、孔容和孔径.X射线光电子能谱(XPS)、H2程序升温还原(H2-TPR)和NH3程序升温脱附(NH3-TPD)的分析结果则显示,Zr能提高催化剂表面化学吸附氧浓度,促进Mn3+转化为Mn4+,从而使催化剂表面的活性位点增多,氧化还原能力增强,同时还提高了催化剂表面酸性位点的数量和强度,促进了NH3的吸附,是MnOx/ZrO2/MWCNTs催化剂低温SCR活性提高的主要原因.     

多壁碳纳米管修饰的CdS/TiO2复合光催化材料的制备及其光解水制氢特性

以P25 TiO₂(德国Degussa化学公司)粉末为原料采用溶胶-凝胶法制备了含有不同CdS质量分数的复合光催化剂,利用多壁碳纳米管(MWCNTs)对CdS/TiO₂进行修饰,制备了一系列不同CdS含量的MWCNTs/CdS/TiO₂光催化材料。对所得的光催化剂进行了扫描电镜、低温氮吸附-脱附及光解水制氢活性的表征。研究了MWCNTs对CdS/TiO₂催化剂体系光解水制氢活性的影响。结果表明,MWCNTs的引入均使得光解水产氢量(14.0 μmol)增加,与未加入MWCNTs的复合光化剂产氢量(11.6 μmol)相比,平均产氢率增加了18%,最高可达21%。     

Pd/MWCNTs(多壁碳纳米管)催化剂的制备及其Heck反应催化活性

以浓硝酸处理后的多壁碳纳米管(MWCNTs)为载体,通过微波辅助法简单而快速地制备了高度分散、粒径均一的Pd/MWCNTs催化剂。利用XRD、HRTEM、XPS等手段对催化剂进行了表征。考察了Pd/MWCNTs催化剂对Heck反应的催化活性,并优化了反应温度、碱的种类和用量等反应条件。结果表明,Pd/MWCNTs在Heck反应中具有良好的催化活性。     

Ce掺杂对碳纳米管负载Mn催化剂结构及SCR反应性能的影响

采用等体积浸渍法制备多壁碳纳米管(MWCNTs)负载Ce-Mn的催化剂,考察了Ce掺杂对Mn/MWCNTs催化剂上NH₃选择性催化还原(SCR)NO_x反应活性的影响.并运用透射电镜扫描、N₂吸附-脱附、程序升温还原、X射线光电子能谱、X射线衍射等手段,重点考察了Ce掺杂对Mn/MWCNTs催化剂结构性质的影响.结果表明,Ce掺杂能显著提高催化剂的SCR活性,其活性增量随着Ce含量的增加先增大后减小;当Ce/Mn为0.6时,催化剂活性最佳.表征结果显示,Mn/MWCNTs中添加Ce后,金属氧化物在MWCNTs上的分散程度提高;催化剂的比表面积和孔体积增大,平均孔径减小;氧化能力提高;表面氧含量增加,Mn化合价升高;结晶度降低,Mn主要以无定形或微晶形式存在,Ce主要以CeO₂物相存在.     

Characterization of Pd/TiO2 embedded in multi-walled carbon nanotube catalyst with a high photocatalytic activity

Pd particles loading on TiO₂-embedded multi-walled carbon nanotubes (MWCNTs), MWCNTs, and TiO₂ particles were prepared via an impregnation method with palladium(II) chlorate solution followed by heat treatment at high temperature. To characterize the catalysts, BET surface area, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, energy dispersive X-ray, Fourier transform infrared spectroscopy and ultraviolet-visible spectroscopy were employed. The prepared catalysts were tested in degradation of methyl orange under visible light. Pd/TiO₂-MWCNTs catalyst demonstrates the highest photocatalytic activity, and the phase transformation from PdO to Pd0 phase takes place at heat treatment of embedded TiO₂. The nanoparticles size of TiO₂ can be decreased by introduction of MWCNTs species. Combining structural characterization with kinetic study results we could conclude that the superior catalytic performance could arise due to the Pd/TiO₂-MWCNTs catalyst’s structure.     

Zr 改性MnOx/MWCNTs催化剂的结构特征与低温SCR活性

以ZrO（NO₃）₂·2H₂O为前驱体对多壁碳纳米管（MWCNTs）进行了改性并负载MnO_x制备了MnO_x/ZrO₂/MWCNTs 催化剂. 考察了Zr 对催化剂低温选择性催化还原（SCR）反应活性的影响,并通过多种分析手段对催化剂的结构进行了表征. 结果表明Zr 的添加对催化剂的低温SCR活性具有显著的促进作用,当Zr 负载量为30%时,催化剂活性最佳. X射线衍射（XRD）、拉曼（Raman）光谱、透射电镜（TEM）、N₂吸附-脱附的表征结果分析表明,适量的Zr 改性促进了MnO_x在载体表面的分散,增强金属氧化物与MWCNTs 之间的作用,也能增加催化剂的比表面积、孔容和孔径. X 射线光电子能谱（XPS）、H₂程序升温还原（H₂-TPR）和NH₃程序升温脱附（NH₃-TPD）的分析结果则显示,Zr 能提高催化剂表面化学吸附氧浓度,促进Mn³⁺转化为Mn⁴⁺,从而使催化剂表面的活性位点增多,氧化还原能力增强,同时还提高了催化剂表面酸性位点的数量和强度,促进了NH₃的吸附,是MnO_x/ZrO₂/MWCNTs 催化剂低温SCR活性提高的主要原因.     

Doping effects of manganese on the catalytic performance and structure of NiMgO catalysts for controllabe synthesis of multi-walled carbon nanotubes

Doping effects of manganese （Mn） on catalytic performance and structure evolution of NiMgO catalysts for synthesis of multi-walled carbon nanotubes （MWCNTs） from methane were investigated for the first time. Addition of Mn in NiMgO catalyst can greatly improve the MWCNTs yield. Mno.2NiMgO catalyst among the tested ones gives the highest MWCNTs yield as 2244%, which is two times higher than that of the catalyst without Mn. The structure evolution, reduction behaviors and surface chemical properties of MnNiMgO catalysts with various Mn contents were studied in detail. It was found that the stable solid solution of NiMgO2 formed in NiMgO catalyst was disturbed by the addition of Mn. Instead, another solid solution of MnMg608 is formed. More amount of Ni can be reduced and dispersed on the catalyst surface to be acted as active sites. Importantly, the changes of Ni content on the surface are correlated with the Ni particle size and the outer diameter of MWCNTs, suggesting the controllable synthesis of MWCNTs over MnNiMgO catalysts.     

MnOx/MWCNTs低温氨选择性催化还原NOx硫中毒机理

以经过浓硝酸和等离子体放电预处理后的多壁碳纳米管(MWCNTs)为载体, 锰氧化物(MnO_x)为活性组分, 采用等体积浸渍法制备MnO_x/MWCNTs 催化剂. 利用热重分析(TGA)、扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)、程序升温还原/脱附(TPR/TPD)以及傅里叶变换红外(FTIR)光谱对催化剂进行表征, 探讨SO₂对催化剂低温氨选择性催化还原(SCR)NO_x活性的影响及SO₂中毒机理. 结果表明, 低温下SO₂对MnO_x/MWCNTs 催化剂活性有明显毒化作用. 反应温度越高, SO₂浓度越大, 催化剂SCR活性下降越快. 活性中心Mn原子硫酸化是催化剂失活的主要原因. 另外, 催化剂表面生成硫酸铵盐以及SO₂对NO吸附的抑制作用也一定程度上造成了催化剂的失活.     

多壁碳纳米管固载金鸡纳生物碱季铵盐类手性相转移催化剂的制备及其催化烷基化反应性能

制备了多壁碳纳米管(MWCNTs)固载的金鸡纳生物碱季铵盐类手性相转移催化剂PTC-1/MWCNTs,并用于催化N-二苯亚甲基-甘氨酸叔丁酯的不对称烷基化反应中.采用紫外-可见光谱系统研究了五种有机溶剂对PTC-1在MWCNTs上吸附和脱附的影响.结果表明,在甲苯中,MWCNTs对PTC-1的吸附率最高(53%),而在三氯甲烷中PTC-1的脱附率最低(仅为0.75%).PTC-1/MWCNTs催化剂在催化N-二苯亚甲基-甘氨酸叔丁酯和不同卤代烃的不对称烷基化反应中,所得产物的收率和对映体选择性都较高,而且该催化剂可回收循环使用,说明PTC-1经MWCNTs固载后,仍能够有效地催化多种卤代烃的不对称烷基化反应.     

多壁碳纳米管负载Cu2O和CuI催化剂上芳醛与2-氨基吡啶氧化酰胺化反应：Cu（I）物种的催化作用

采用浸渍法制备了多壁碳纳米管(MWCNT)负载的Cu2O和CuI催化剂,并运用粉末X射线衍射、红外光谱、扫描电镜-能量散射谱、透射电镜和NH3程序升温脱附等技术对催化剂进行了表征。结果表明,催化剂中沉积的Cu2O和CuI分别以立方相和γ相存在于MWCNT上,且表现出由弱到强的拉电子(Lewis酸)性能。将催化剂用于催化芳醛与2-氨基吡啶氧化酰胺化反应合成N-(吡啶-2-基)苯酰胺类化合物,产物选择性为100%,收率为50%–95%。 CuI/MWCNT催化剂上产物分离收率性能好于Cu2O/MWCNT,但后者的循环使用性能更好。与共价的CuI相比,离子化的Cu2O与极性的酸活化的MWCNT间具有更适宜的相互作用,这种不同的相互作用可显著影响2-氨基吡啶的氨基对芳醛羰基的亲核进攻速率。     

Catalysis of Multi‐walled Carbon Nanotubes Supported PdxCoy Nanoparticles Prepared by a Pyrolysis Method Using Ionic Liquids as the Solvent toward Ethanol Oxidation Reaction

Multi‐walled carbon nanotubes (MWCNTs) decorated with Pd_xCo_y (the nominal atomic ratios of Pd to Co were 3:1, 3:1.5, 3:2, 3:3, respectively) nanoparticles (denoted as Pd_xCo_y/MWCNTs ) were fabricated by a simple pyrolysis process, in which room temperature ionic liquids (RTILs) of butyl‐3‐methylimidazolium hexafluorophosphate (denoted as [BMIM]PF₆) was used as the solvent. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) were all used to characterize the Pd_xCo_y/MWCNTs catalysts, showing that the Pd_xCo_y particles were dispersed on the surface of the MWCNTs with an average particle size of ～25.0 nm. The electro‐catalytic activity of the Pd_xCo_y/MWCNTs catalysts toward ethanol oxidation reaction (EOR) was examined by cyclic voltammetry (CV). It was revealed that the onset potential was ～90 mV lower and the peak current was about four times higher for ethanol oxidation for Pd₃Co_1.5/MWCNTs compared to those of Pd₃Co₁/MWCNTs. The possible catalysis mechanisms of the Pd₃Co_1.5/MWCNTs toward EOR were also discussed.     

Pd/MWCNTs贫燃甲烷催化燃烧性能研究

以MWCNTs为载体,用HNO_3做氧化剂对MWCNTs进行处理,通过XPS研究了处理前后MWCNTs表面官能团的变化,并采用超声浸渍法制得Pd/MWCNTs催化剂,借助TEM,揭示了Pd粒子在催化剂表面分散度和粒径与MWCNTs表面含氧量、羟基和羰基间的关系。并考察了Pd/MWCNTs催化剂预处理方法对低浓甲烷催化燃烧活性和稳定性的影响,研究表明,Pd的价态以及Pd粒子的粒径,都与催化剂的甲烷燃烧活性直接关联。单质Pd的氧化和Pd粒径的长大是导致催化剂性能衰减的原因。通过原位FT-IR技术对反应气氛下中间物种的监测,提出了Pd/MWCNTs催化剂上的低浓度甲烷催化氧化反应机理。     

Enhanced oxygen reduction at Pd catalytic nanoparticles dispersed onto heteropolytungstate-assembled poly(diallyldimethylammonium)-functionalized carbon nanotubes

Both Keggin-type phosphotungstic acid (HPW) and Pd are not prominent catalysts towards the oxygen reduction (ORR), but their composite Pd-HPW catalyst produces a significantly higher electrochemical activity for the ORR in acidic media. The novel composite catalyst was synthesized by self-assembly of HPW on multi-walled carbon nanotubes (MWCNTs) via the electrostatic attraction between negatively charged HPW and positively charged poly(diallyldimethylammonium (PDDA)-wrapped MWCNTs, followed by dispersion of Pd nanoparticles onto the HPW-PDDA-MWCNT assembly. The as-prepared catalyst was characterized by transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, thermal gravimetric analysis (TGA), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). TEM images show that Pd nanoparticles were uniformly dispersed on the surface of MWCNTs even when the Pd loading was increased to 60 wt%. Electrochemical activity of the catalysts for the ORR was evaluated by steady state polarization measurements using a rotating disk electrode. Compared with the acid treated MWCNTs, Pd nanoparticles supported on the HPW-assembled MWCNTs show a much higher ORR activity that is comparable to conventional Pt/C catalysts. The high electrocatalytic activities could be related to high dispersion of Pd nanoparticles as well as synergistic effects originating from the high proton conductivity of HPW. The Pd/HPW-PDDA-MWCNTs system as the cathode catalyst in proton exchange membrane fuel cells is demonstrated.     

氮杂石墨烯碳纳米管复合材料负载Pt催化剂在甘油选择性氧化中的应用

一直以来,以碳材料为载体负载的金属催化剂被广泛应用于甘油液相氧化反应.研究表明,催化剂活性与碳的孔径分布有关,随着碳载体微孔比例的增加,催化剂活性下降.此外,载体表面基团对金属活性有着重要影响.例如,载体表面含氧基团的吸电子作用可降低载体表面电子的流动性(电子密度和导电性),从而阻碍甘油氧化反应过程中OH–的吸附和再生,导致反应活性降低.因此,开发微孔比例小、富含负电性基团的碳载体成为甘油氧化过程中急需解决的问题之一.本文通过热解碳纳米管(MWCNTs)和三聚氰胺的混合物,在碳纳米管表面直接生长得到氮杂石墨烯(NG-MWCNTs),并采用SEM,N2吸附,TEM和XRD对所得复合材料进行了表征.实验发现,相比于单纯的MWCNTs和直接热解三聚氰胺所得的产物CNx,NG-MWCNTs具有更高的比表面积(173 m2/g)和更大的平均孔径.此外,NG-MWCNTs非常适合作为Pt催化剂的载体,Pt平均粒径可小至1.4±0.4 nm.所制备的Pt/NG-MWCNTs催化剂在甘油选择性氧化反应中具有很高的催化活性和甘油酸选择性(甘油转化率和甘油酸选择性分别可达64.4%和81.0%),且具有可重复使用性能.Pt/NG-MWCNTs催化剂优异的催化活性不仅与载体表面高分散的Pt有关,而且与N原子对Pt的给电子作用有关.     

Pd/PVP-MWCNTs电极对甲酸氧化的电催化性能

用聚乙烯吡咯烷酮（PVP）修饰的多壁碳纳米管（MWCNTs）作为Pd纳米粒子的载体,制得了Pd/PVP-MWCNTs催化剂并研究了其对甲酸氧化的电催化性能. 红外光谱仪（FTIR）和透射电镜（TEM）观测结果表明,Pd/PVP-MWCNTs催化剂中的Pd纳米粒子平均粒径小、分散性好. 因此,Pd/PVP-MWCNTs催化剂对甲酸电氧化有很好的电催化性能.     

高利用率多壁碳纳米管负载金铂合金纳米粒子催化剂在碱性溶液中的甲醇电催化氧化性能研究

使用乙二醇还原法合成了一系列高利用率多壁碳纳米管负载的金铂双金属纳米粒子电催化剂,在碱性溶液中由循环伏安和计时电流法测试该AuPt催化剂对于甲醇氧化反应的电催化活性.透射电子显微镜、X射线衍射与X射线能谱观测催化剂形貌,表征催化剂结构.结果表明,金铂双金属纳米粒子均匀分散在碳纳米管上,催化剂具有良好甲醇电氧化性能.实验表明Au/Pt/MWCNTs比为10∶8∶32(bymass)时,该催化剂具有最高甲醇电氧化峰电流密度与最负起始氧化电位.     

Multiwalled carbon nanotubes drive the activity of metal@oxide core-shell catalysts in modular nanocomposites

Rational nanostructure manipulation has been used to prepare nanocomposites in which multiwalled carbon nanotubes (MWCNTs) were embedded inside mesoporous layers of oxides (TiO(2), ZrO(2), or CeO(2)), which in turn contained dispersed metal nanoparticles (Pd or Pt). We show that the MWCNTs induce the crystallization of the oxide layer at room temperature and that the mesoporous oxide shell allows the particles to be accessible for catalytic reactions. In contrast to samples prepared in the absence of MWCNTs, both the activity and the stability of core-shell catalysts is largely enhanced, resulting in nanocomposites with remarkable performance for the water-gas-shift reaction, photocatalytic reforming of methanol, and Suzuki coupling. The modular approach shown here demonstrates that high-performance catalytic materials can be obtained through the precise organization of nanoscale building blocks.     

高催化活性Pd-Co3O4/MWCNTs催化剂对甲醇氧化的电催化性能

以Co(NO3)3·6H2O为钴源,聚乙二醇(PEG)20000为表面活性剂,与多壁碳纳米管(MWCNTs)混合后通过水热氧化法成功地合成了表面均匀分布纳米絮状Co3O4的MWCNTs复合物,进一步还原Pd的前驱体而制备得到Pd-Co3O4/MWCNTs复合催化剂.利用扫描电镜(SEM)、透射电镜(TEM)及X射线粉末衍射(XRD)等手段对样品的形貌和晶型结构进行了表征,结果表明Pd纳米粒子为面心立方晶体结构,均匀地分布在Co3O4修饰的MWCNTs表面.用循环伏安法和计时电流法表征结果表明:催化剂Pd-Co3O4/MWCNTs具有较大的电化学活性表面积,在碱性介质中对甲醇氧化具有更高的电催化活性和稳定性.研究结果表明,过渡金属氧化物纳米Co3O4颗粒在提高直接甲醇燃料电池(DMFC)催化性能研究中具有十分重要的作用,是一类很有潜力的载体催化剂.     

Hydrogen storage in ni nanoparticle-dispersed multiwalled carbon nanotubes

Hydrogen storage properties of mutiwalled carbon nanotubes (MWCNTs) with Ni nanoparticles were investigated. The metal nanoparticles were dispersed on MWCNTs surfaces using an incipient wetness impregnation procedure. Ni catalysts have been known to effectively dissociate hydrogen molecules in gas phase, providing atomic hydrogen possible to form chemical bonding with the surfaces of MWCNTs. Hydrogen desorption spectra of MWCNTs with 6 wt % of Ni nanoparticles showed that approximately 2.8 wt % hydrogen was released in the range of 340-520 K. In Kissinger's plot to evaluate the nature of interaction between hydrogen and MWCNTs with Ni nanoparticles, the hydrogen desorption activation energy was measured to be as high as approximately 31 kJ/mol.H(2), which is much higher than the estimates of pristine SWNTs. C-H(n)() stretching vibrations after hydrogenation in FTIR further supported that hydrogen molecules were dissociated when bound to the surfaces of MWCNTs. During cyclic hydrogen absorption/desorption, there was observed no significant decay in hydrogen desorption amount. The hydrogen chemisorption process facilitated by Ni nanopaticles could be suggested as an effective reversible hydrogen storage method.