Effect of soil properties on radioactivity concentrations and dose assessment

This study evaluated the correlation between radioactivity concentrations and soil properties, and determined the total annual effective dose near an underground geologic repository for transuranic wastes. Soil samples were collected from two historical monitoring areas (Near Field and Cactus Flats). Alpha-particle spectrometry was used for the analysis of ²⁴¹Am, ^239+240Pu and ²³⁸U, while ¹³⁷Cs, ⁴⁰K, ²³²Th and ²²⁶Ra were detected by gamma ray spectrometry. Higher radioactivity concentrations and stronger positive correlations between radioactivity concentrations and soil properties were obtained in Cactus Flats compared to Near Field. The total annual effective dose was lower than the recommended limit of 1 mSv y^??1.

     

A case study on uptake of thorium from soil to plant by using X-ray fluorescence spectrometry

A case study was carried out to determine the uptake of thorium from soil to plant by using X-ray fluorescence technique. The radioecological experiment was undertaken to provide plant/soil concentration ratio (CR) data for thorium using 2 types of plant (barley and common vetch)×4 levels of Th(0, 1500, 3000,4500ppm)×2 types of soil (acidic and alkaline) with different configuration parameters. The calibration of the analytical method for thorium on dry basis of samples is described by using¹⁰⁹Cd excitation source. The results indicated that theCR values decreased with the corresponding Th concentration in soils with a 1000 fold range and differed among soil and plant types.     

Environmental monitoring and public dose assessment around the Tokai Reprocessing Plant

Radiological effects to the regional environment around Tokai Reprocessing Plant (TRP) were assessed using both actual environmental radiological monitoring data and doses estimated by mathematical models. The environmental monitoring showed no increase of radiological level except for the influences from atmospheric explosion tests, the Chernobyl accident, and domestic accidents. Estimated annual effective dose for the public was only 0.1% of the annual dose limit recommended by the ICRP. This revised version was published online in July 2006 with corrections to the Cover Date.     

Radiological assessment of natural radionuclides in soil from playgrounds in Southwestern Nigeria and evaluation of radiation dose

Journal of Radioanalytical and Nuclear Chemistry - The activity concentrations of natural radionuclides in soil from playground were determined by gamma spectrometry using NaI(Tl) detector. Annual...     

Measurement of activity concentration of primordial radionuclides in soil samples from Thirthahalli taluk and the assessment of resulting radiation dose

The activity concentration of primordial radionuclides ²²⁶Ra, ²³²Th, and ⁴⁰K in soil samples of Thirthahalli taluk were measured systematically by using a low background HPGe detector coupled to 16 K MCA. The measured activity concentration of ²²⁶Ra lies between 5.1?±?0.2 and 79.5?±?1.7 Bq kg^?1with an average activity of 25.99 Bq kg^?1, ²³²Th ranges from 5.1?±?0.3 to 95.3?±?2.2 Bq kg^?1with an average activity of 33.60 Bq kg^?1and that of ⁴⁰K varies from 18.3?±?1.5 to 833.4?±?17.5 Bq kg^?1with an average activity of 175.52 Bq kg^?1. Higher concentration of these radionuclides were found in the soil samples where the regional geology is granites. The consequential gamma dose and the corresponding radiation hazard was also estimated and is found to be within the permissible limits. The possible radiological impact on the public was also determined and these results are presented in this paper.     

Rapid assessment of soil pollution with kerosene using a carbon-nanotube-based piezosensor

The possibility of determining the kerosene content in the ground using a flash detector with open cell detection based on a piezosensor is considered. The coating of the electrodes of a quartz crystal resonator and its weight for the detection of kerosene vapors in a wide concentration range, the structural parameters of the flash detector housing, the conditions for detecting kerosene vapors above ground are optimized. The accuracy and reliability of assessing of the level of kerosene contamination in different types of soils are estimated in field conditions.     

Thermodynamic and kinetic study of the single extraction of mercury from soil using sodium-thiosulfate

The use of sodium-thiosulfate (Na-thiosulfate) as a reagent for the extraction of mercury (Hg) from soil was investigated. High organic matter content in soil plays a major role in retaining metals. It has previously been reported that using the cold vapour atomic absorption method, powerful reagents such as EDTA, DTPA and cysteine could not release Hg from soil samples. The optimal conditions for using Na-thiosulfate to extract soil-Hg are presented here. Our results show that 50 ± 5% of total Hg was extracted from soil samples using 0.01 mol L⁻¹ of the reagent without pH adjustment. Increasing the reagent concentration above this level showed no significant change in Hg extraction. From this extraction three fractions of Hg were obtained, the labile, slowly labile and un-extractable. We further applied the use of a kinetic extraction approach that has never been applied for Hg. We observed a correlation between the first two fractions and the quantity of organic matter content in soils. The labile fraction could be released by using any concentration of the reagent. However, the slowly labile fraction was dependent on time and increased concentrations of Na-thiosulfate. Furthermore, our results suggest that the labile and slowly labile fractions involve two different sites of reduced sulphur groups contained in soil organic matter and Hg levels present in the soil samples did not appear high enough to saturate all these high affinity sulphur sites. The capacity of Na-thiosulfate to reduce (Hg(II)) to (Hg(0)), was determined to be negligible. Our results further suggest the implication of iron (Fe(II)) for reducing Hg(II) to Hg(0). Here we have demonstrated that Na-thiosulfate is an effective reagent in the extraction of Hg from soil, with the particular characteristic of its ability to remove strongly bound Hg from sulphur groups contained in soil organic matter.     

The operator dose assessment of landmine detection systems using the neutron backscattering method

Personal safety issue is one of the major limitations in landmine detection by nuclear techniques. In this paper, the dose rate received by the operator of different hand-held landmine detection systems using the neutron backscattering method was investigated. Monte Carlo method was used to simulate a computational model of the body, instruments with different shielding configurations and soil with various moisture contents. The effective dose received by the different organs of the operator has been estimated by using two different approximation methods including average equivalent dose and dose equivalent assessment. The results obtained by these two methods were compared. The common results showed that the operator dose rate depends on the facility shielding, soil moisture level, and source-to-operator distance. Also, although the absorbed dose received by most organs generally decreases as a function of source to operator distance, for some organs such as kidneys and lungs it firstly increases when source-to-operator distance increases up to 0.7–1.2 m and after that the absorbed dose decreases. Furthermore, the results showed that the effective dose received by the operator has its maximum value when the source to operator distance is 0.60 m.     

Environmental pollution study by multielemental neutron activation analysis of garden soil samples from Nagpur City, India

A multielemental instrumental neutron activation analysis (INAA) method has been employed for the determination of 30 elements in seven garden soil samples from Nagpur City and two intercomparison soil standards from IAEA, Vienna and Institute of Radioecology and Applied Nuclear Techniques (IRANT), Slovak Republic. Environmental implications of elemental concentrations in different soils have been discussed.     

4E assessment of power generation systems for a mobile house in emergency condition using solar energy: a case study

Journal of Thermal Analysis and Calorimetry - This contribution experimentally and analytically addresses the dripping and ignition mechanism of vertically discrete polypropylene (PP) and...     

Carbon-mineral adsorbents from waste materials: case study

Waste bleaching earth from the food industry obtained in the process of fruit juice purification was utilized for preparation of carbon-mineral adsorbents. The waste material, containing 25.8 wt% C, was subjected to three kinds of treatment: (1) direct pyrolysis at 400 degrees C with a suitable temperature program; (2) preliminary hydrothermal modification (200 degrees C, 8 h, 15.3 atm) and then pyrolysis as in method 1; (3) preliminary thermal treatment (400 degrees C) and then chemical treatment (boiling in 3% solution Na(2)CO(3)), followed by heating at 400 degrees C (10 min). Moreover, the materials obtained by these methods were subjected to additional thermal treatment at 700 degrees C with a suitable temperature program. Both the morphology and the topography of carbon deposits and, in consequence, the porous structure of the obtained adsorbents depend on the method of their preparation. The additional thermal treatment of these samples at 700 degrees C makes it possible to obtain adsorbents of more thermally stable carbon deposits possessing better parameters of the porous structure. Carbon-mineral adsorbents of different specific surface areas (S(BET) from 17.6 to 153 m(2)/g) and pore volumes (from 0.035 to 0.093 cm(3)/g) were prepared. The mechanism of phenol and p-nitrophenol adsorption on the obtained adsorbents was discussed and their properties were compared with the suitable literature data.     

Eliminating unwanted nanobubbles from hydrophobic solid/liquid interfaces: a case study using magnetoelastic sensors

Air bubbles are known to form at the liquid/solid interface of hydrophobic materials upon immersion in a liquid (Holmberg, M.; Kdühle, A.; Garnaes, J.; M?rch, K. A.; Boisen, A. Langmuir 2003, 19, 10510-10513). In the case of gravimetric sensors, air bubbles that randomly form at the liquid-solid interface result in poor sensor-to-sensor reproducibility. Herein a superhydrophilic ZnO nanorod film is applied to the originally hydrophobic surface of a resonance-based magnetoelastic sensor. The superhydrophilic coating results in the liquid completely spreading across the surface, removing unwanted air bubbles from the liquid/sensor interface. The resonance amplitude of uncoated (bare) and ZnO-modified sensors are measured in air and then when immersed in saline solution, ethylene glycol, or bovine blood. In comparison to the bare, hydrophobic sensors, we find that the standard deviation of the resonance amplitudes of the liquid-immersed ZnO-nanorod-modified sensors decreases substantially, ranging from a 27% decrease for bovine blood to a 67% decrease for saline. The strategy of using a superhydrophilic coating can be applied to other systems having similar interfacial problems.     

Environmental plutonium: The curious case of seawater

A method for quantitatively estimating the fractions of plutonium oxidation states that derive from disproportionation, or other oxidation-reduction reactions, is illustrated with data for seawater. The results agree with experiment and can be checked numerically. Attention is drawn to a discrepancy in what we think is known about seawater.     

Risk assessment from gamma dose rate in Balod District of Chhattisgarh,India

Journal of Radioanalytical and Nuclear Chemistry - People are generally exposed to the natural radiation that presents inside and outside the houses. This investigation has been carried out gamma...     

Radiochemical study of leaching of zinc from soil

Problems of the extraction of zinc from soil with solutions of alkaline earth chlorides, sodium and ammonium acetate, EDTA and aqueous solutions of HClO₄ or NaOH with low ionic strength at various pH has been studied using radiotracer⁶⁵Zn. The strong influence of pH on extraction from chloride, acetate and aqueous solutions has been proved. No difference due to the counter ions in chloride extractants has been observed. The distribution coefficient of zinc between soil and the aqueous phase was not influenced by the V/m ratio.     

Environmental assessment of heavy metal and natural radioactivity in soil around a coal-fired power plant in China

Concentrations of heavy metals and natural radionuclides in soil around a major coal-fired power plant of Xi’an, China were determined by using XRF and gamma ray spectrometry, respectively. The measured results of heavy metals show that the mean concentrations of Cu, Pb, Zn, Co and Cr in the studied soil samples are higher than their corresponding background values in Shaanxi soil, while the mean concentrations of Mn, Ni and V are close to the corresponding background values. The calculated results of pollution load index of heavy metals indicate that the studied soils presented heavy metal contamination. The concentrations of ²²⁶Ra, ²³²Th and ⁴⁰K in the studied soil samples range from 27.6 to 48.8, 44.4 to 61.4 and 640.2 to 992.2 Bq kg^?1 with an average of 36.1, 51.1 and 733.9 Bq kg^?1, respectively, which are slightly higher than the average of Shaanxi soil. The air absorbed dose rate and the annual effective dose equivalent received by the local residents due to the natural radionuclides in soil are slightly higher than the mean values of Shaanxi. Coal combustion for energy production has affected the natural radioactivity level and heavy metals (Cu, Pb, Zn, Co and Cr) concentrations of soil around the coal-fired power plant.     

Extraction of thiodiglycol from soil using pressurised liquid extraction

Thiodiglycol (TDG) is the predominant hydrolysis product of the chemical warfare agent sulfur mustard. The extraction of TDG was investigated using pressurised liquid extraction and the results compared for a variety of different solvents and soils. TDG was analysed underivatised by gas chromatography with flame photometric detection. A mixture of methanol-water (9:1), proved to be the most efficient extracting solvent for TDG at a temperature of 150 degrees C and 10 MPa.     

Environmental bioremediation for organometallic compounds: Microbial growth and arsenic volatillization from soil and retorted shale

Nutrient effects on microbial growth and arsenic volatilization from retorted oil shale and soil were evaluated in a laboratory study. Dimethylarsinic acid (DMAA), methanearsonic acid (MAA) and sodium arsenate amendments were used with added nutrients, or with retort process water added to simulate possible co-disposal conditions. In experiments with soil and retorted shale, dimethylarsinic acid showing the highest cumulative arsenic releases, in comparison with added inorganic sodium arsenate (SA). Low but detectable amounts of innate arsenic present in retorted shale could be volatilized with added organic matter. In soil, arsenic volatilization showed a direct relationship to nutrient levels and microbial growth. With shale, in comparison, a threshold response to available nutrients was evident. Distinct increases in fungal community development occurred with nutrients available at a level of 2.5% w/v, which also allowed incresed arsenic volatization. Codisposal of retort process waters with shale allowed arsenic volatilization without the addition of other nutrients. The presence of retort process water limited arsenic volatilization from the added organometallic compounds DMAA and MAA, but not from SA or innate arsenic. These differences should be useful in the definition of permissive and non-permissive environmental conditions for arsenic volatilization in bioremediation programs.     

Sample preparation for metalloprotein analysis: A case study using horse chestnuts

In the present work, 11 different procedures for protein and metalloprotein extraction from horse chestnuts (Aescullus hippocastanum L.) in natura were tested. After each extraction, total protein was determined and, after protein separation through sodium dodecyl sulphate-polyacrylamide gel electrophoresis (SDS-PAGE), those metals belonging to the protein structure were mapped by synchrotron radiation X-ray fluorescence (SRXRF). After mapping the elements (Cr, Fe and Mn) in the protein bands (ca. 33 and 23.7 kDa), their concentrations were determined using atomic absorption spectrometry (ET AAS).

Good results were obtained for protein extraction using a combination of grinding and sonication. However, this strategy was not suitable to preserve metal ions in the protein structure. In fact, there was 42% decrease on Mn concentration using this procedure, compared to that performed with sample agitation in water (taken as reference). On the other hand, when grinding and agitation with an extracting buffer was used, there was a 530% increase of Mn concentration, when compared to the reference procedure.

These results indicate agreement between metal identification and determination in proteins as well as the great influence of the extraction procedure (i.e., the sample preparation step) for preserving metals in the protein structures.