Thermal mass changes of portland cement and SLAG cements after water sorption

A simple water sorption/retention (WS/WR) test, followed by stepwise static heating, was applied to the study of cement quality and the reactivity of its grain surface. The physically bound water and hence the specific surface both in the unhydrated and in the hydrated state were estimated as a function of the hydration time. Rehydration after heating at 220°C and contact with air was different inWS from that inWR samples, which indicates a difference in microstructure. XRD proved the formation of portlandite during the sorption test and eventual heating at 200°C, and its transformation into carbonates on contact with air, especially on heating at 400°C. The contents of these compounds were estimated from the mass difference between 400 and 800°C, which was compatible with the mass change between 220 and 400°C and this indicates surface reactivity. The test may serve for the routine study of cement. Dedicated to Professor Lisa Heller-Kallai on the occasion of her 65^th birthday     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Heat evolution in hydrated cementitious systems admixtured with different set controlling components

Calorimetry has been used in the investigations of cementitious systems with different set controlling admixtures. The kinetics and mechanism of hydration process was thus characterized on two different cement clinkers mixed with calcium sulphate containing materials. These admixtures were collected as a residue in the fluidised bed combustion (FBC) of coals with simultaneous desulphurisation process - so-called bottom ash. Apart from anhydrite/gypsum, they were composed mainly of alumina and silica containing material of disordered structure, originating from the coal contaminations of clay character. Anhydrite/gypsum acts as set controlling admixture. The aluminosilicate component reacts with calcium ions released to the solution from the calcium silicate clinker minerals. It has been found that fluidised bed combustion wastes can be successfully used as set controlling admixture. There is no other harmful effects; those could be easily detectable by calorimetry. However the effect is dependent upon the composition of cement clinker. At low calcium aluminate content a slight acceleration of hydration process can be easily observed, particularly at higher amount of admixture. In the mixtures with high calcium aluminate clinker the heat evolved is slightly reduced in the presence of admixture. The dominating role of aluminate phase in heat evolution process within the first hours of hydration process has been thus proved. This revised version was published online in July 2006 with corrections to the Cover Date.     

The Use of Starch Drying Kinetics Curves for Experimental Determination of Its Specific Surface Area

The most popular method for the calculation of specific surface area is its determination from water vapour sorption isotherms. The study presented here has been designed for the purpose of optimisation and selection of the conditions of drying so as to allow the determination of specific surface area from plotted curves of the drying process. The results indicate that drying curves can be used as the basis for the determination of specific surface area, the values of which do not differ statistically significantly (α = 0.05) from those determined from isotherms of water vapour sorption (adsorption/desorption).     

Simultaneous IR/TG study of calcium carbonate in two aged cement pastes

Two aged cement pastes (7 years) were studied for H₂O and CO₂ evolution, the combined amounts of which were measured by TG and identified by thermo-IR analysis. This indicated the presence of three forms of carbonates, which decomposed at different temperatures. The displacement with time of the evaporation of sorbed water to higher temperatures (500–700°C, TG, MS) shows the possibility of its incorporation into carbonate hydrates and/or hydroxy hydrates, postulated previously. The decomposition of all the hydration products needed a thermal energy increasing with ageing (increased temperature measured by TG). The carbonation process proceeded for 7 years in the weaker paste, whereas it terminated before 5 years in the stronger one. The CSH water content did not change with ageing, whereas that of portlandite was lowered, which though did not account for the increase in carbonate content (TG). Possibly some Ca²⁺ from the CSH gel was involved in this process. In the stronger paste the growth with time of organic matter was found (IR, TG/DTG).     

聚羧酸共聚物侧链结构对水泥水化及硬化过程的影响

以聚乙二醇系列、丙烯酸、顺酐、丙烯酸羟乙酯为原料合成聚羧酸减水剂,讨论聚羧酸共聚物侧链长度对水泥分散性能和水化过程的影响,并测试掺加减水剂的混凝土性能.实验结果表明:通过调整聚羧酸共聚物中侧链链长的比例使其具有最佳的分散性.实验合成的聚羧酸共聚物聚乙二醇侧链为nPEG600∶nPEG400=1∶1时,分散效果最好,水泥浆体的流动度及分散力最佳,分别为289 mm和10.36.聚羧酸减水剂具有缓凝特性,能够显著延缓水泥水化及硬化过程,使水泥石的后期水化更充分、水化产物结构更紧密更有力量,各龄期混凝土抗压强度都有较大提高.在水泥中添加0.3%聚羧酸减水剂(PEG600∶400),32.5#水泥3 d,7 d和28 d的抗压强度分别提高了50.4%,40.8%,35.1%,42.5#水泥3 d,7 d,28 d的抗压强度分别提高了16.7%,31.0%和22.3%.     

热脱附-单体稳定同位素技术测定挥发性有机物

采用热脱附与稳定同位素质谱联用技术分析了城市不同源及大气环境中挥发性有机物排放的单体同位素特征。系统考察了样品进样量、进样方式和样品分离度对同位素分馏影响情况。使用填有Tenax TA的吸附管采集汽油车尾气、汽油挥发、柴油车尾气、柴油挥发、溶剂挥发和餐饮油烟等污染源,以及城市不同功能区的挥发性有机物(VOCs)样品,不同污染源中挥发性有机物的稳定碳同位素δ13C值不同,97#汽油车尾气的δ13 C值偏重,平均值为-25.84‰,富集13 C;餐饮油烟的δ13 C值偏轻,平均值为-30.26‰。油品挥发比燃烧后以尾气的形式排放的苯系物δ13 C值重。厦门市各功能区挥发性有机物的δ13 C平均范围在-27.03‰~-25.40‰,接近于汽油和柴油挥发及尾气中的δ13 C值,表明厦门市空气中挥发性有机物以机动车排放源为主。     

Gravimetric,Volumetric And Calorimetric Studies of The Surface Structure of Portland Cement

Dry cement powder and hardened cement paste were characterised by means of laser granulometry and volumetric measurement of the nitrogen adsorption isotherm at 77 K. Water sorption isotherms at ambient temperature were measured stepwise by means of a gravimetric apparatus. The isotherms show a very large hysteresis loop, reaching down to zero relative pressure, which reflects swelling of the cement gel. Thermoporometric measurements reveal that swelling of that gel consists in water take up within the continuously growing structure; no stable pore structure could be observed. This revised version was published online in August 2006 with corrections to the Cover Date.     

Novel resin modified glass-ionomer cements with improved flexural strength and ease of handling

Poly(acrylic acid-co-itaconic acid) copolymers containing pendent methacrylates were synthesized and used to formulate redox-initiated in situ cured glass-ionomer cements (GICs) by mixing with reactive glass fillers (Fuji II LC). Various formulations for the redox initiator were studied, and flexural strength (FS) was used as a screening tool for optimization. Effects of molecular weight (MW), grafting ratio, comonomer, polymer content in the liquid composition, powder/liquid (P/L) ratio, and aging on FS were investigated. The results show that the in situ cured GICs demonstrated higher FS (89.6-123.2 MPa), as compared to commercial Fuji II LC GIC (57.1 MPa). The optimal concentrations for redox initiators were found to be 0.15% (by weight) for K₂S₂O₈ and 0.2% for ascorbic acid (or 0.6% for microencapsulated ascorbic acid), respectively. Effects of MW, grafting ratio, P/L ratio and polymer content in the liquid formulation were significant. During aging, the cement showed an increase in strength over 24 h and then no change for time periods up to six months. SEM analysis supports the strength data associated with the formulations. The exotherm and setting time suggest that novel redox-initiated resin-modified GICs hold promise as biocompatible and workable cement for orthopedic applications.     

Humidity‐induced surface modification of boric acid

Previous studies of boric acid powder suggest that the surface undergoes restructuring when exposed to changes in relative humidity of the surrounding air. This present work investigates these surface changes using atomic force microscopy (AFM) to provide quantitative topographic information, supplemented by gravimetric analysis of water sorption. The AFM images clearly show the dissolution of small rounded features and z‐height growth of the larger flatter areas, indicating that Ostwald ripening was the prevailing mechanism in the restructuring. Estimation of radii of curvature of asperities on the surface enabled the approximation of supersaturation ratio in the surface film using the Kelvin equation. The value of 1.007 obtained is much less than the value of 3.2 reported for solution‐grown boric acid. It is this high level of supersaturation that is thought to account for the inherent roughness of boric acid, associated with dendritic growth. Conversely, the low supersaturation ratio estimated for the adsorbed surface layer results in regular crystal growth and a decrease in surface roughness. Gravimetric analysis of boric acid revealed a steady loss in water with increase in relative humidity from 10% to 60%. This is attributed to loss of available surface area through the progressive dissolution of fine surface features. Desorption showed a monotonic decrease in water uptake, confirming that the restructuring is not reversible. Changes in surface area were estimated from the AFM images. The loss of surface area between dry and ambient conditions was greater than that inferred from the loss of mass in the gravimetric analysis. This suggests that water is retained on the surface in capillaries that are not apparent in the AFM surface scans. Statistical monolayer coverage of water is achieved at 10% relative humidity, which corresponds to the onset of surface restructuring indicated by the water sorption isotherm. Copyright © 2004 John Wiley & Sons, Ltd.     

Adsorption of water vapor on a non-porous carbon surface and evaluation of the mesopore surfaces of active carbons

Adsorption of water vapor on non-porous carbon adsorbents (blacks) with different specific surfaces and a sufficiently high concentration of primary centers was studied. The maximum value of the adsorption is proportional to the surface and corresponds to the formation of (1.7±0.3) dense monomolecular layers. A method was proposed for determining the surface of non-porous carbon adsorbents and for evaluating the mesopore surfaces of active carbons.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 12, pp. 2048–2051, December, 1993.This work was supported by the Russian Foundation for Basic Research (Grant 93-035635).     

A study of surface adsorption on silver powders

DSC and TG-DTA techniques were used to investigate micro-sized silver powder particles and the adsorption of ethyl cellulose on these particles in a solution of ethyl acetate. The apparent specific heat of the silver particles was determined, and the kinetics of temperature-programmed desorption (TPD) of these adsorbed silver particles was investigated. Results show that the apparent specific heat and desorption kinetic parameters obtained by thermal analysis techniques could be used to characterize certain physico-chemical properties of such a particulate system.     

Calcite,vaterite and aragonite forming on cement hydration from liquid and gaseous phase

Cement hydration products were studied as influenced by the hydration conditions (hydration time in liquid phase; relative humidity, RH, in gaseous phase). The formation of calcium hydroxide (portlandite, P) and its transformation to calcium carbonates is mainly discussed here. More hydration products, including P, were formed in liquid phase (paste) than in water vapor (powder), due to the higher availability of water molecules. Full hydration was observed only in the paste hydrated for 6 month, otherwise the P content, estimated from its water escape, DM(400-800°C), increased after storage in water vapor of the prehydrated paste. All the three polymorphs of CaCO₃ (calcite, vaterite and aragonite) were found on prolonged contact with air of the hydrated powder (XRD, HRTEM). Their content was dependent on sequence of RH conditions on hydration: higher after water retention, WR, on lowering RH=1.0→0.95→0.5, than after water sorption, WS, on increasing RH in the inverse order. It increased also on wetting and drying, both of hydrated powder and paste. Ca was found to accumulate on the micro-surfaces of WR samples (SEM, TEM), whereas more Al was observed on WS samples and the crystallinity of hydration products was here higher (ED). Dissolution-diffusion-recrystallization was possible: small Al-ions concentrated at one end and the bigger Ca ions - at the other end of some needles (TEM). At 400-500°C the P in cement transforms in air into CaCO₃, which decomposes at 600-700°C. Thus the sensitivity to carbonation was estimated from ΔM(600-800°C). This value was similar in pastes hydrated for 1 month and in powder (WR). It was lower in powder WS and much lower in the paste (6 months). It increased pronouncedly when the prehydrated paste was stored in water vapor in WS. The nanocrystals of portlandite, vaterite and aragonite, embedded in the amorphous matrix, were observed by HRTEM in the hydrated powder. They may contribute to the cement strength. This revised version was published online in July 2006 with corrections to the Cover Date.     

Intermediate detection in real time using reactive surface desorption dielectric‐barrier discharge ionization mass spectrometry

Reactive intermediates play key roles for reaction mechanism elucidation. A suitable tool for identifying the key intermediates is crucial and highly desirable. In this study, surface desorption dielectric‐barrier discharge ionization (reactive SDDBDI) was developed for characterization of the reactive intermediates. In reactive SDDBDI, the plasma is doped with a reagent before the plasma ions are directed at a cover slip surface bearing another analyte. Different from SDDBDI, reactive SDDBDI can be used both as an ambient ionization source and as a means to produce reagent ions for ambient ion/molecule reactions. The online derivation of 4‐aminophenol with trifluoroacetic anhydride demonstrated that reactive SDDBDI can be used for chemical analysis where improved specificity or sensitivity is required. The utility of this approach for real‐time detection of reactive intermediate was demonstrated by the Schiff‐base and Eberlin reactions. The formed intermediates and products could be readily detected and identified by tandem mass spectrometry. These results indicate that reactive SDDBDI can be used to generate reagent ions that undergo ion/molecule reactions in the open air with an analyte at condensed phase on a surface. Reactive SDDBDI has high‐efficiency ion transmission and high MS sensitivity. It is thus a potential tool to perform ambient ion/molecule reactions and detect reactive intermediates.     

Structure and dynamics of hydrated NH(4) (+): an ab initio QM/MM molecular dynamics simulation

A combined ab initio quantum mechanical/molecular mechanical (QM/MM) molecular dynamics simulation has been performed to investigate solvation structure and dynamics of NH(4) (+) in water. The most interesting region, the sphere includes an ammonium ion and its first hydration shell, was treated at the Hartree-Fock level using DZV basis set, while the rest of the system was described by classical pair potentials. On the basis of detailed QM/MM simulation results, the solvation structure of NH(4) (+) is rather flexible, in which many water molecules are cooperatively involved in the solvation shell of the ion. Of particular interest, the QM/MM results show fast translation and rotation of NH(4) (+) in water. This phenomenon has resulted from multiple coordination, which drives the NH(4) (+) to translate and rotate quite freely within its surrounding water molecules. In addition, a "structure-breaking" behavior of the NH(4) (+) is well reflected by the detailed analysis on the water exchange process and the mean residence times of water molecules surrounding the ion.     

Multiphoton ionization spectroscopy in surface analysis and laser desorption mass spectrometry

The application of resonance-enhanced multiphoton ionization (REMPI) spectroscopy for the ultrasensitive detection of molecules originating from laser desorption experiments performed on a variety of substrates is reviewed. Laser-induced desorption from surfaces is capable of producing intact gas-phase molecules, even from polar, non-volatile, high-molecular-weight and thermally labile substances. REMPI is a highly efficient and optically selective ionization method, which, coupled with laser desorption allows the direct chemical analysis of complex mixtures, without the need for previous sample purification and separation steps. The use of REMPI spectroscopy is discussed in two contexts: (1) for the direct chemical analysis of complex mixtures, e.g., environmental samples, by laser desorption/laser postionization mass spectrometry and (2) for measurements of internal state distribution of molecules laser-desorbed from sub-monolayers surface films to gain insight into the laser desorption mechanism.Presented at the 13th International Symposium on Microchemical Techniques (ISM), held in Montreux, Switzerland, May 16–20,1994     

Hydration of Cement Slurry in The Presence of Spent Cracking Catalyst

The physicochemical properties of spent fluidized bed cracking catalyst and its influence on hydration process of cement slurry were studied. The samples were cement slurries prepared with water/solid=0.5 and additions of used catalyst amounted to 0, 5, 10, 15, 20 and 25%with resp. to the solid. After definite time they were subjected to thermogravimetric analysis (TG, DTG, DTA) and, in order to determine the progress of reaction with water, the heat of hydration was measured by means of isotherm calorimetry. The studies disclosed that the spent cracking catalyst is not merely an inactive filler in cement slurries, but it modifies the course of the hydration process. The spent catalyst is a pozzolana additive and its presence leads to a decrease of calcium hydroxide contents in the system. The spent catalyst affect on the heat of cement hydration. Small amounts additive accelerate the process of binding. This revised version was published online in August 2006 with corrections to the Cover Date.     

A Conduction Calorimeter for Measuring the Heat of Cement Hydration in the Initial Hydration Period

A new-design conduction microcalorimeter is described, which has been used to measure the heat of cement hydration evolved in the initial period of hydration. The calorimeter is 30 cm³ in volume; the heat loss coefficient is 27.270±0.015 W V^–1, the time constant is 300 s. This revised version was published online in July 2006 with corrections to the Cover Date.     

Water sorption in poly(ammonium sulfopropylbetaines). I. Differential scanning calorimetry

The hydration of four amorphous acrylic and methacrylic poly(zwitterions) bearing the ammonium sulfopropylbetaine function as a side-groups () was studied by differential scanning calorimetry over broad ranges of temperature (150-400 K) and water content (weight fraction W₁ < 0.5). Analyses were made of the first-order transitions and heat capacity of sorbed water, glass transition temperature (T_g) measurements. Nonfreezable bound water, about 7.7 ± 0.9 mol/monomeric unit, behaves as a single phase: Its mobility, fairly similar to that of bulk liquid water in viscoelastic systems at T > 250 K, decreases with temperature in the glassy systems, but never disappears, even at 185 K. The depression of the glass transition temperature of the hydrated polymers obeys Couchman's equation: T_g = Σ_i W_i ΔC_pi T_gi / Σ_gi W_iΔC_pi. Freezable bound water, about 6.7 ± 0.9 mole/monomeric unit, shows multipeak melting endotherms in the range 242–272 K. Because of their charged sites, the hydration process of the poly(zwitterions) appears more similar to that of poly(electrolytes) than to that of uncharged hydrophilic polymers. © 1992 John Wiley & Sons, Inc.     

高比表面积TiO_2纳米管的制备与表征

采用一种简单的化学合成方法制备TiO2 纳米管 ,并采用TEM、XRD等分析手段对TiO2 纳米管进行了表征 .考察了不同温度对TiO2 纳米管比表面积及孔体积的影响 .结果表明 ,采用该方法制得的TiO2 纳米管 ,比用模板法制备的TiO2 纳米管的管径小、管形均匀 .此纳米管的比表面积大于 2 0 0m2 /g ,孔体积最大可达 0 .784cm3 /g .