A positron annihilation lifetime measurement system with an intense positron microbeam

An intense positron microbeam was formed using an electron linear accelerator. The beam is pulsed to apply positron lifetime spectroscopy to very small samples and to obtain positron lifetime images by scanning it. Positron lifetimes are measured with time resolution of <300 ps and with lateral spatial resolution of 30–100 μm. A counting rate of the γ-ray to measure positron lifetime is about 10³ s⁻¹ which is 10 times higher than that achieved by the radioisotope based microbeam.     

Temperature dependence of radiation effects in polyethylene: Cross‐linking and gas evolution

High‐density polyethylene (HDPE) and low‐density polyethylene (LDPE) were irradiated in vacuo at 30–220 and 30–360°C, respectively, with γ‐rays at doses of 10–400 kGy. Temperature dependence of cross‐linking and gas evolution was investigated. It was found that cross‐linking was the predominant process up to 300°C and the gel point decreased smoothly with temperature. The increase of G(x) with temperature was likely attributed to the temperature effect on addition of radicals to the double bonds present in the polymer. Above 300°C, the gel fraction at a given dose decreased remarkably with temperature and turned to zero at 360°C. The molecular weight variation determined with gel permeation chromatography (GPC) indicated the enhanced degradation at 360°C by radiation. G‐values of H₂ increased with temperature and varied with dose. The compositions of the C₁–C₄ hydrocarbons evolved depended on the structures of side branches. Raising the temperature favored the formation of unsaturated hydrocarbons, and the yield of unsaturated relative to saturated hydrocarbons decreased with dose. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1541–1548, 1999     

Temperature dependence of positron lifetime in ordered porous silica (SBA-3)

The temperature dependence of positron lifetime in uniform mesopores was analyzed. We used SBA-3 as the sample material, which possesses an ordered porous structure with uniform cylindrical mesopores. The positron lifetime corresponding to the annihilation in the mesopores increased gradually with a decrease in temperature down to 100 K, and its relative intensity also increased concomitantly. This result was attributed to the lower probability of the escape of the ortho-positronium (o-Ps) from the mesopores into the intergrain space at lower temperatures. An anomalous and sudden increase in the lifetime was observed at around 100 K; this result was in agreement with an increase in the positron lifetime reported in a previous study. It was revealed that the increase in the lifetime is very steep in cases of uniform mesopores, suggesting that the temperature dependence is influenced by the pore size.     

Electron irradiation induced microstructural modifications in BaCl2 doped PVA: A positron annihilation study

Thin films of pure and 10 wt% BaCl₂ doped poly(vinyl alcohol) (PVA) were prepared by solution casting method. These films were subjected to electron irradiation for different doses ranging from 0 to 400 kGy in air at room temperature. The effect of electron irradiation on the optical and free volume related microstructures of these polymer films was studied using positron annihilation lifetime spectroscopy, FTIR and UV-vis techniques. The FTIR spectral studies indicate that the electron irradiation induces chemical modifications within the doped PVA, which results in chain scission as well as cross-linking of the polymer. The positron lifetime study on these irradiated polymers shows that the chain scissions and cross-linking within the polymer matrix affect the free volume content and hence the microstructure. The UV-vis optical absorption studies show that the induced microstructural change by electron irradiation also modifies the optical properties. Using UV-vis spectra, the optical energy band gap was estimated and it decreases with increase in electron dose. A correlation between positron results and optical results is obtained and electron irradiation induced microstructure modifications within the doped polymer are understood. The results highlight the usefulness of positron annihilation technique in the study of the microstructure of irradiated polymers.     

The temperature dependence of the local free volume in polyethylene and polytetrafluoroethylene: A positron lifetime study

Positron lifetime measurements, performed in the temperature range 80–300 K, are reported for polyethylene (PE) and polytetrafluoroethylene (PTFE). The lifetime spectra have been analyzed using the data processing routines LIFSPECFIT and MELT. Two long-lived components appear, which are attributed to pick-off annihilation of ortho-positronium in crystalline regions and at holes in the amorphous phase. The ortho-positronium lifetimes, τ₃ and τ₄, are used to estimate the crystalline packing density and the size of local free volumes in the crystalline and amorphous phases. The interstitial free volume in the crystals exhibits a weak linear increase with the temperature which is attributed to thermal expansion of the crystal unit cell. In the amorphous phase, the hole volume varies between 0.053 and 0.188 nm³ (PE) and between 0.152 and 0.372 nm³ (PTFE). Its temperature variation may be fitted by two straight lines, the intersection of which is used to estimate a glass transition temperature of T_g = 195 K for both PE and PTFE. The slopes of the free volume in the glassy and crystalline phases with the temperature correlate well with each other. The coefficients of thermal expansion of the hole volume are compared with the macroscopic volume change below and above the glass transition. From this comparison a fractional hole volume at T_g of 4.5 (PE) and 5.7% (PTFE) and a number of 0.73 (PE) and 0.36 (PTFE) × 10²⁷ holes/m³ is estimated. Finally, it is found that the intensity of o-Ps annihilation in crystals shows a different temperature dependence to that in the amorphous phase. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1513–1528, 1998     

On the measurement of structural relaxation in polymers using positron annihilation lifetime spectroscopy

Positron annihilation lifetime spectroscopy has been identified as an effective means of characterizing the free volume content of amorphous polymers. The lifetime and intensity of the ortho-positronium (o-Ps) pick-off annihilation has been found to correlate with the average size and density of free volume sites, respectively. Recently, PALS has been used to evaluate and monitor the physical aging and structural relaxation of polymers in terms of both initial state and evolution in state with time. However, during extended PALS measurements in insulating materials, an electric field can build up due to positron-electron annihilation and can effectively reduce the probability of positronium formation. In this paper, an observed decrease in intensity associated with the o-Ps annihilation component in the glassy polymers polycarbonate and polystyrene is found to be unrelated to structural relaxation of the materials over the time periods examined as reported earlier by others, and, instead, to be more likely a result of electric charge build-up. © 1993 John Wiley & Sons, Inc.     

Composition and self-irradiation effects on the positron annihilation lifetime properties of poly(ethylene-co-vinyl acetate)

The behavior of the copolymer poly(ethylene-co-vinyl acetate), with different amounts of vinyl acetate (VA) (2, 4.5, 9 and 19 w/w%, respectively), has been studied by performing positron lifetime measurements as a function of temperature. An overall reduction of the ortho-positronium formation probability I₃ with increasing VA content is observed. The copolymers with 2, 4.5 and 9 w/w% VA show a V-shaped I₃ evolution with temperature, caused by positron irradiation induced ionization, whereas the copolymer with 19 w/w% VA has become practically inert to self-irradiation effects.     

Study of relaxation processes in polyethylene and polystyrene by positron annihilation

Relaxation processes in polyethylene (PE) and polystyrene (PS) were studied by positron annihilation technique. For PE, above the glass transition temperature, T_g, the size of free volumes and its concentration were increased by the micro-Brownian motion of molecules. For PS, local motions of molecules in backbone chains were found to start above 260 K. However, these local motions were suppressed by an interphenyl correlation. For both PE and PS, below 250–260 K, the formation probability of positronium atoms increased with decreasing temperature. This fact was assigned to the freezing in of the local motions of molecules. For PS, an onset of the local motions of molecules was observed above 100 K. These motions were expected to be associated with liberation of phenyl groups. © 1996 John Wiley & Sons, Inc.     

Transition and relaxation processes of polyethylene,polypropylene, and polystyrene studied by positron annihilation

Transition and relaxation processes of polyethylene (PE), polypropylene (PP), and polystyrene (PS) were studied by the positron annihilation technique. From measurements of lifetime spectra of positrons as a function of temperature, the lifetime of ortho-positronium, τ₃, and its intensity, I₃, were found to increase above 260 K for PP. This fact was attributed to a cooperative motion of large segments of molecules above the glass transition temperature, T_g. For PE, above T_g (140 K), the value of τ₃ increased, but the temperature coefficient of I₃ was negative below 230 K. From this fact, for PE, the molecular motions that cause the glass transition were associated with a rearrangement of molecules by local motions such as kink motions. The discrepancy between the results for PE and PP was attributed to the presence of methyl groups in PP and the resultant suppression of the local motions. For PS (T_g = 340 K), the molecular motions were found to start above 260 K, but those were suppressed by an interphenyl correlation. Detailed annihilation characteristics of positrons in polymers were also discussed. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1601–1609, 1997     

Temperature and strain-rate dependence of yield stress of polyethylene

The yield stress behavior of a range of polyethylene materials which differ with respect to their short chain branch content has been studied. Measurements carried out over a wide range of temperatures have shown that there is a sudden transition in the behavior of the yield stress at a temperature which is dependent on both the grade of material and the applied strain rate. These results are in agreement with previous results found from analysis of the yield strain behavior. Above the transition temperature the materials all behave in a nonlinear viscoelastic manner, and the yield process is considered as being propagation controlled. Below the transition temperature the materials all behave in an elastic-plastic manner, and the yield process is considered as being nucleation controlled. Below the transition temperature the temperature dependence of the yield stress is determined by the thickness of the crystalline lamellae. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2177–2189, 1998     

Optical and microstructural studies on electron irradiated PMMA: A positron annihilation study

The effect of electron irradiation on the free volume related microstructural and optical properties of Poly(methyl methacrylate) have been studied using Positron Annihilation and other techniques. The FTIR spectral study on the irradiated films suggests the existence of CC group and is understood by invoking the carbonaceous clusters as a consequence of chain scission in PMMA. Using UV-Visible absorption spectra the optical parameters like optical energy bandgap and activation energy were determined and the variation of these parameters suggests the existence of defects within the irradiated sample. Following Robertson’s theory, the carbonaceous cluster size is estimated and it increases with increase in electron dose. The XRD study indicates the enhancement of amorphous nature of the film due to chain scission by irradiation. The Positron annihilation result shows that electron irradiation affects the free volume related microstructure and the carbonaceous clusters may act as positron scattering centers.     

Positron annihilation in irradiated and unirradiated polyethylenes

Positron lifetimes were measured for four kinds of polyethylene samples and were resolved into four components. The temperature dependence of the two longlived components was examined in detail. In agreement with other results, the longest lived component could be reasonably assigned to ortho-positronium located in amorphous regions. This component was shown to be sensitive to the defects in high-density polyethylene introducted in the course of its production. Both the intensity and the lifetime of the second longest lived component were structure insensitive, i.e., they did not change even on passing through the melting point. This component has been tentatively assigned to a positronium compound state. The effect of gamma-ray irradiation was also examined. Although the intensity (I₄) of the longest lived component was reduced by the irradiation, correlation between I₄ and the free radical concentration was poor, and the reduction in I₄ caused by the irradiation is considered to be due to structure change and not to chemical reasons.     

Mechanism for nuclear excitation during positron annihilation using Coulomb wave functions

We have calculated cross sections for the process of nuclear excitation during positron annihilation on any bound electron. We used Coulomb wave functions for the electron and positron.     

Temperature dependence of the free volume in polytetrafluoroethylene studied by positron annihilation spectroscopy

The temperature dependence of the free volume holes in pure polytetrafluoroethylene (PTFE) and doped with 25% glass have been studied in the temperature range (30–250 °C) using positron annihilation lifetime spectroscopy. The data clearly revealed the glass transition temperatures for pure and doped PTFE are 130 and 110 °C, respectively. As the temperature increases, the free volume distribution becomes positioned at larger free volume hole size. A good correlation between the electrical conductivity and the o-Ps parameters was achieved.     

Gamma irradiation effect upon positron annihilation in ultra high molecular weight poly(ethylene oxide)

Positron annihilation technique was used to reveal the evolution of small pore structure of semi-crystalline ultra high molecular weight poly(ethylene oxide) under γ-irradiation. It has been established that the structure of poly(ethylene oxide) is improved under low dose irradiation (<20 kGy), while the concentration of free-volume holes in amorphous regions increases at higher doses. The results were compared with those from small angle X-ray scattering and wide angle X-ray scattering measurements of the same samples.     

Radiation-induced crosslinking of polyethylene in the presence of acetylene: A gel fraction,UV-visible,and ESR spectroscopy study

Electron-spin resonance (ESR) and altraviolet (UV) visible spectroscopic evidence has been found for the formation of diene, triene and tetraene, following the irradiation of polyethylene in the presence of acetylene. The polyenes are formed by a mechanism which is different from that observed under vacuum or with inert gas saturation. The sum of the G (polyene) values obtained by UV spectroscopy is almost half that of initial radical formation. It is concluded that polyene bridges, predominantly diene, form crosslinks between radical pairs. G (X) values determined from gel fraction data, using Saito-Kang-Dole theory, are found to be greatly in error and misrepresentative of crosslink changes. © 1993 John Wiley & Sons, Inc.     

High sensitivity of positron annihilation lifetime to time and pressure effects in gas-exposed polymers

Positron annihilation lifetime (PAL) experiments are performed in polycarbonate (PC) exposed to CO₂ and He gases as a function of time and pressure. In PC/CO₂ systems, hole size and fraction reduced from PAL data increase as a function of CO₂ pressure and exposure time. Significant hysteresis in positron lifetime data is observed during CO₂ abasorption/desorption. In PC/He systems, no variation is observed. Hole size distribution in the CO₂-exposed polymers is found to be significantly broader than in unexposed samples. The high sensitivity of PAL results to CO₂ exposure of PC is thought to relate to the microstructural changes in the polymer matrix, such as penetrant plasticization, gas hydrostatic pressure effect, and molecular filling and creation of holes.     

Temperature dependence of free volume of polyacrylamide gels studied by positron lifetime measurements

Changes of positronium (Ps) cavity radii in polyacrylamide and poly(N-isopropylacrylamide) gels were studied from 120 to 300 K by positron lifetime technique and it has been shown that the Ps cavity radius in the hydrogels changes by three or four stages. Temperature dependence of the Ps cavity radius exhibits variations similar to common polymers around the glass transition temperature. Hydrophilicity of the polymer chains significantly affects the Ps cavity radius just below 273 K. These results suggest an important role of free volume on the state of water in hydrogels.     

A new method of stabilization and characterization of the interface in binary polymer blends by irradiation: A positron annihilation study

New methods for stabilizing the interface of partially miscible and immiscible binary polymer blends and characterizing such an interface are described here. Interfacial modifications in four binary polymer blend systems namely PS/PMMA, PVC/EVA, PP/NBR, and PVC/SAN were induced by e‐beam and microwave irradiation. These changes have been characterized in terms of free volume measured by Positron lifetime technique and DSC as supplementary to free volume data. The changes observed in free volume parameters upon irradiation could not be connected to the changes at the interface and also not specific to composition of the blend. Owing to this limitation, we exploited the usefulness of hydrodynamic interaction parameter α derived from the very same free volume data to monitor the changes at the interface. The present results demonstrated that α is effective in revealing the changes at the interface and can be used to characterize the interfacial properties in partially miscible and immiscible polymer blends. Further, the results clearly show that microwave irradiation is a better route to stabilize the interface of a partially miscible or immiscible blend if its component polymers contain polar groups. E‐beam irradiation seems to be better route if the component polymers of the blend contain no polar groups. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 619–632, 2009     

Temperature and strain rate dependence of yield strain and deformation behavior in polyethylene

The deformation behavior of a range of polyethylene materials which differ with respect to both their short-chain branch content and molecular weight has been studied. Mechanical measurements carried out over a wide range of temperatures have shown that there is a sudden transition in the measured tensile yield strain at a temperature which is dependent on both the grade of material and the applied strain rate. Above the transition temperature all of the materials behave in a nonlinear viscoelastic manner and the wide-angle X-ray scattering patterns obtained have shown that at low applied strains reorientation of the lamellae is observed before necking. Below the transition temperature the materials all behave in an elastic-plastic manner and there is no evidence of lamellar reorientation before necking. This transition in yield mechanism is not apparent when considering the yield stress data alone. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys, 35: 545–552, 1997