Influence of241Am mobility by sodium humate

The influence of aqueous solution of sodium humate on the transport of²⁴¹Am from the soil into solution and acceleration of movement through a soil layer has been studied. It was found that under static condition the presence of 150 mg sodium humate in 100 ml water accelerates the liberation of²⁴¹Am from soil into the solution. The mobility of²⁴¹Am through a column of soil increased significantly since the concentration of sodium humate in the entering solution exceeded 100 mg.1^–1. Artificially contaminated podsol soil from Brno site and sodium humate isolated by alkaline extraction from sediments of North Bohemian (Duchcov) origin have been used for the investigation.     

Neutron activation analysis of iodine in soil

A simple pre-irradiation procedure for the separation of iodine from soil has been developed. A soil sample was heated in a quartz tube for 15 min at about 900 °C. The evaporated iodine was collected in activated charcoal, which was produced from phenol resin with low impurities. The charcoal, with sorbed iodine, was irradiated by neutrons and the¹²⁸I produced was measured. A successful elimination of the background radioactivity due to the matrix elements was possible with this separation procedure. The detection limit by this method for soil samples was about 0.1 mg/kg (dry). The method has been applied to analyze selected soil samples.     

Development of a pressurized liquid extraction and clean-up procedure for the determination of alpha-endosulfan, beta-endosulfan and endosulfan sulfate in aged contaminated Ethiopian soils

Pressurized liquid extraction (PLE) was investigated for the extraction of two endosulfan isomers and their metabolite from two real contaminated soil samples. PLE for 3x10min at 100 degrees C was proven to be more exhaustive than Soxhlet extraction (SOX) in one soil sample. On the other soil sample investigated the method was found to be equally exhaustive as SOX. The use of hazardous organic solvents such as n-hexane, toluene, and diethyl ether has been avoided in PLE and clean-up. Instead less toxic solvents have been used both at the extraction step (acetone/n-heptane) and clean-up step (ethyl acetate/n-heptane). A column Florisil clean-up procedure that consumes relatively low solvent volumes has been optimized and applied to purify soil extracts. The developed analytical procedure was validated by applying it to a certified reference soil material (CRM811-050). A recovery of 103% total endosulfan residue was obtained versus certified values.     

Extracting Syringe for determination of organochlorine pesticides in leachate water and soil-water slurry: a novel technology for environmental analysis

The Extracting Syringe (ESy), a novel membrane-based sample preparation technique directly coupled as an autosampler to gas chromatography, has been employed for the analysis of organochlorine pesticides (OCPs) in raw leachate water. The ESy has also been applied for extraction of OCPs from contaminated soil samples and its performance has been compared to liquid-solid extraction (LSE) and accelerated solvent extraction (ASE). Extraction of 3-mL leachate sample at the optimised conditions resulted in enrichment factors from 32 (Endrin aldehyde) to 242 (Endrin) and detection limits from 1 to 20 ng/L. The inter-day and intra-day repeatability (% RSD) at 100 and 500 ng/L were <6% and <24%, respectively. The relative recovery at 100 and 500 ng/L ranged from 68% (Aldrin) to 116% (Endrin aldehyde); except Heptachlor that showed 51 and 60%, respectively. The ESy extraction of the slurry-made soil samples revealed occurrence of Endosulfan I (18.2 microg/g soil), 4,4'-DDE (2.6 ng/g soil), Endosulfan II (8.7 microg/g soil) and Endosulfan sulfate (1.1 microg/g soil); showing good agreement with LSE results. The total ESy consumption of organic solvents was 4.2 mL from which only 0.6 mL n-undecane was used during the extraction step (7 microL for the extraction per se), while in the LSE and ASE, it was 420 and 18.1 mL, respectively. The ESy extraction time (0.5 h) was comparable to the ASE time (0.6 h); and the time required for the LSE was 3.75 h. To sum up, the ESy has shown its competency to LSE and ASE technologies, demonstrating its applicability for environmental analysis of organic pollutants, towards green techniques for green environment.     

Variation of the rare earth element concentrations in the soil, soil extract and in individual plants from the same site

Samples of various types (spruce needles, blackberry leaves, soils, and soil extracts) have each been taken at 6 places from the same site. In addition, 4 whirls each from 2 spruce trees were sampled. Rare earth elements (REEs) were determined in these samples by neutron activation analysis with a chemical group separation. Variations between places were found to be small with soils and soil extracts, but large with plants. Variations between whirls were small. Plants neither reflected the soil nor the soil extract. Both plant species were dissimilar, but the logarithm of their ratio was a linear function of the atomic number of the REE. A negative Ce anomaly (with respect to soil) was found in both plant species.     

土壤中有机氯农药残留分析用标准样品的制备

介绍了土壤中有机氯农药残留分析用标准样品的制备方法。土壤样品经风干、研磨、筛分、混匀后装瓶。样品经索氏提取、弗罗里硅土小柱净化后,采用气相色谱-质谱法对残留的有机氯农药进行测定。结果表明,采自沈阳地区的土壤中的有机氯农药含量分布较为均匀,是一种理想的环境标准样品候选物样品。该研究为土壤中有机氯农药残留分析用标准样品的研制奠定了基础。     

Determination of zearalenone and ochratoxin A in soil

Mycotoxins are secondary metabolites, formed by the action of fungi on agricultural crops in the field or during storage. These metabolites are highly toxic to animals and humans and high levels have been measured in agricultural crops. In order to evaluate human risks due to ingestion of mycotoxin-contaminated food different methods have been developed for analysis of mycotoxins in cereals and maize. In this project the focus was on mycotoxins in agricultural soil and the fate of these toxins in the soil-water-plant system. Two different mycotoxins were selected in the study: zearalenone (ZON) produced by species of Fusariumor Aspergillusand ochratoxin A (OTA) produced by species of Penicillium. We developed a method for analysis of these toxins in soil. Soil samples were extracted with methanol-water (9:1) and purified by solid-phase extraction (SPE, C8-columns). The final extract was analysed using high-pressure liquid chromatography (HPLC) with fluorescence detection. A Phenyl Hexyl column was used to separate the toxins. The detection limits obtained were 0.1 and 1.0 microg kg(-1) dry weight (dw) for OTA and ZON, respectively. The developed method has been used for analysis of different soils in connection with growth chamber experiments. The soil types used in the growth chamber experiments were a sandy soil, a sandy clay soil, and a soil with high content of organic matter. The recovery was determined as 85.8 and 93.4% and the repeatability to 5.1 and 12.8% for OTA and ZON, respectively. The reproducibility obtained was 8.5 and 15.0% for soil samples, representing concentration levels from 0.2-30 microg kg(-1) dw (OTA) and from 1.0-100 microg kg(-1) dw (ZON).     

Effects of airborne fluoride on soil and vegetation

The study was initiated by the sudden uncontrolled release of airborne fluorides in 2005 into the environment from aluminium smelter factory that caused damage of vegetation. Samples of corn leaves and corn male flower heads with visible symptoms of fluoride intoxication had been collected in autumn 2005. Increased contents of total fluoride, which exceeded the maximum allowable content of fluorine in feeding stuffs, including meadow grass, were detected. During continuation of the study some commercially available herbal teas and plants used for preparing herbal teas infusions, collected in the field in 2010, were investigated to investigate possible uptake of fluoride from the soil. Nettle (Urtica dioica) has been found to be a promising passive bioindicator for monitoring phytotoxic effects of fluoride in the soil on the vegetation. Good correlation between labile free fluoride in the soil and total fluoride in the nettle has been found, while total fluoride in the soil, soil pH and the dominant wind direction were also proven as important factors influencing the uptake of fluoride by the nettle.     

The potential use of continuous-flow isotope-ratio mass spectrometry as a tool in forensic soil analysis: a preliminary report

The use of continuous-flow isotope-ratio mass spectrometry (CF-IRMS) as a tool in soil analysis has been assessed as part of a larger study using a number of geological techniques applied in a forensic context. Carbon and nitrogen isotopic ratios, delta13C and delta15N, have been analysed to investigate situations which have arisen from crime casework. Three questions have been addressed: the role of spatial variation found over the short-scale (less than 20 m), temporal variation over a period of almost 2 years, and the variation found between source soils and soil transferred to footwear soles during a simple one-stage transfer process. Results are presented for the three experiments. The use of carbon and nitrogen isotopes has been shown to be useful in discriminating between soil types and sample locations, even when sampling occurs at a different time (as might be the case with a crime scene). In cases of primary transfer (from a source soil by a one-stage transfer to another surface, in this case, shoes and boots), the combination of carbon and nitrogen isotope ratios is a valuable tool in discriminating between sites and in showing the relationship of the transferred samples to the relevant source soils. Used in combination with other analytical techniques, isotopic analysis may prove to be a useful tool in a forensic context.     

Multiresidue analysis of insecticides in soil by gas chromatography with electron-capture detection and confirmation by gas chromatography-mass spectrometry.

A rapid multiresidue method has been developed for the analysis of nine insecticides (organochlorines, pyrethroids and organophosphorus) in soil. The method is based on the sonication extraction of residues from a certain amount of soil placed in a small column, using ethyl acetate. The effect of the residence time of insecticides in soil, the material of the columns used (glass or plastic columns) and the soil moisture content on the recovery of these compounds was also studied. Residues were determined by gas chromatography with electron-capture detection. The average recovery through the method obtained for these compounds varied from 90 to 108% with a relative standard deviation between 1 and 11%. The results of this study pointed out that the recoveries of insecticide residues obtained with plastic or glass columns at different soil moisture content were similar and that the residence of these compounds in soil during several days did not affect their recovery from soil. Confirmation of residue identity was performed by gas chromatography coupled with mass spectrometry.     

Biomimetic oxidation of plant protecting agents

The suitability of two in vitro oxidation systems as chemical models for the biological degradation of plant protecting agents has been investigated. As representative herbicides diclofop, fenoxaprop, isoproturon, linuron and monolinuron have been oxidised by two systems, the Fentons' reagent and the ascorbic acid oxidation system (AAOS) and the results compared to those of the known metabolic pathways of these compounds. The herbicides have been oxidised by Fentons' reagent (hydroxy radicals). The main products were isolated by preparative scale HPLC and identified with (1)H-NMR and MS. Some of the products have been identified by comparing their retention times and UV/Vis-spectra to those of standard compounds. Several products known from biological degradation are also found after chemical oxidation, however, notable differences between the two pathways have been observed, for instance in the case of diclofop. Oxidation by the AAOS leads to comparable results. Reaction rates for the oxidation with the AAOS have been studied and compared with data known from degradation studies of the herbicides in soil. Compounds which are slowly degraded in soil are oxidised more slowly in the biomimetic process than those with a fast degradation in soil.     

Estimation of the Soil Toxicity Level in the Areas of Anthropogenic Mineral Deposits by Means of Quantitative Parameters and Biotesting

The level of soil pollution in the areas of manganese slug dumps from ferroalloy production has been estimated on the basis of heavy metal content of soils and response of test plants. The concentrations of heavy metals in soils have been determined, the corresponding hazard factors have been calculated, and the toxicity level of soils has been assessed. Such studies make it possible to simultaneously judge the amount of toxicants (namely heavy metals) in soils and evaluate the level of soil toxicity by the response of biological species used in biotesting.     

A device for automatic subsampling of soil, sediment and plant material for proficiency testing

Summary An automatic sampler for soil, sediment and plant material has been developed for use in the IPE, ISE and SETOC programmes, organized from the Wageningen Agricultural University (The Netherlands). The device was tested to determine the homogeneity of a dry loess soil and a Gladiolus sample.     

Effect of Liquid Animal Manure Application on the Solubilization of Heavy Metals from Soil

Abstract

The effect of liquid animal manure on heavy metal solubilization in soil has been studied in the laboratory; three different types of experiments were carried out:

1) aerobic and anaerobic incubation of soil/manure mixtures

2) desorption of heavy metals from soil, as affected by manure liquid fraction

3) gel permeation chromatography of soil/manure aqueous extracts to identify components responsible for heavy metal solubilization.

Alf three different approaches showed that complexation involving high molecular weight dissolved organic matter from the soil/manure matrix is (together with pH) the most important driving force for heavy metal solubilization. As a consequence, chemical and microbial processes (e.g. nitrification) that influence dissolved organic matter concentrations in the soil solution, determine the degree of heavy metal solubilization in manured soil.     

Determination of concentrations of chromium and other elements in soil and plant samples from leather tanning area by Instrumental Neutron Activation Analysis

Chromium, one of the toxic elements, along with other elements has been determined in samples of soil and plant (leaves and seeds) from Jajmau Area, Kanpur district, India, which is irrigated with effluent waste water from leather tanning industries. Soil and plant samples were collected from these areas and analyzed by Instrumental Neutron Activation Analysis (INAA) using high flux reactor neutrons and high resolution gamma-ray spectrometry. Concentrations of fifteen elements in soil and five elements in plant samples were determined by relative method. Chromium concentrations were found to be in range of 45–3,900 mg kg^?1in soil samples and 14–83 mg kg^?1 in plant samples. This study showed that Cr is present in significant amounts, in the soil as well as in the plant samples, near to the leather tanning area. As a part of quality control work, IAEA reference material (RM) SL-3 and NIST standard reference material (SRM) 1645 were analyzed and the quality of the results has been evaluated by calculating % deviations from recommended/literature/certified values.     

Thermodynamic and kinetic study of the single extraction of mercury from soil using sodium-thiosulfate

The use of sodium-thiosulfate (Na-thiosulfate) as a reagent for the extraction of mercury (Hg) from soil was investigated. High organic matter content in soil plays a major role in retaining metals. It has previously been reported that using the cold vapour atomic absorption method, powerful reagents such as EDTA, DTPA and cysteine could not release Hg from soil samples. The optimal conditions for using Na-thiosulfate to extract soil-Hg are presented here. Our results show that 50 ± 5% of total Hg was extracted from soil samples using 0.01 mol L⁻¹ of the reagent without pH adjustment. Increasing the reagent concentration above this level showed no significant change in Hg extraction. From this extraction three fractions of Hg were obtained, the labile, slowly labile and un-extractable. We further applied the use of a kinetic extraction approach that has never been applied for Hg. We observed a correlation between the first two fractions and the quantity of organic matter content in soils. The labile fraction could be released by using any concentration of the reagent. However, the slowly labile fraction was dependent on time and increased concentrations of Na-thiosulfate. Furthermore, our results suggest that the labile and slowly labile fractions involve two different sites of reduced sulphur groups contained in soil organic matter and Hg levels present in the soil samples did not appear high enough to saturate all these high affinity sulphur sites. The capacity of Na-thiosulfate to reduce (Hg(II)) to (Hg(0)), was determined to be negligible. Our results further suggest the implication of iron (Fe(II)) for reducing Hg(II) to Hg(0). Here we have demonstrated that Na-thiosulfate is an effective reagent in the extraction of Hg from soil, with the particular characteristic of its ability to remove strongly bound Hg from sulphur groups contained in soil organic matter.     

Extraction and analysis of avermectines in agricultural soils by microwave assisted extraction and ultra high performance liquid chromatography coupled to tandem mass spectrometry

A method for the analysis of avermectines (abamectine, doramectine and ivermectine) in soils has been developed. The analytes are extracted with acetonitrile/water (90:10) by using microwave assisted extraction. The extract is cleaned-up through solid phase extraction with Oasis HLB cartridges and analyzed by ultra high performance liquid chromatography coupled to tandem mass spectrometry (UHPLC-MS/MS). Separation is obtained in 3 min. Extraction of analytes from the soil, that is the most critical point, has been studied in detail, and the effect of soil composition and aging time on the analytes recovery has been investigated.     

土壤中镉对酸雨的敏感性研究

模拟土壤在自然酸雨淋洗条件下镉的释放行为,研究了不同酸度、不同酸雨成分、不同流量的酸雨对土样中镉淋出的影响,以及镉在不同碳酸根含量的土样对酸雨淋洗的敏感性。     

Optimisation and comparison of microwave-assisted extraction and Soxhlet extraction for the determination of polychlorinated biphenyls in soil samples using an experimental design approach

Optimisation of microwave-assisted extraction (MAE) for the extraction of polychlorinated biphenyls (PCBs) from soil samples has been accomplished using an experimental design approach. Variables studied have been: percentage of acetone (v/v) in an acetone:n-hexane mixture, solvent volume, extraction time, microwave power and pressure inside the extraction vessel. Five samples of a certified soil (CRM 481) have been extracted under the optimum conditions of the developed method and the results have been compared to those obtained by Soxhlet extraction. Good recoveries (>95%) have been obtained for all the PCBs studied. All extracts have been analysed by gas chromatography/mass spectrometry (GC/MS) and an optimum determination method for the electron impact mass spectrometric (EIMS) has also been developed.     

Solid-phase microextraction-gas chromatographic determination of volatile monoaromatic hydrocarbons in soil

Benzene, toluene, ethylbenzene, three isomers of xylene, and cumene have been isolated and enriched from soil samples by a combination of water extraction at room and elevated temperature and headspace-solid-phase microextraction before their gas chromatographic-mass spectrometric (GC-MS) determination. The conditions used for all stages of sample preparation and chromatographic analysis were optimized. Analytes sampled on a polydimethylsiloxane-coated solid-phase microextraction fiber were thermally desorbed in the split/splitless injector of a gas chromatograph (GC) coupled with a mass spectrometer (MS). The desorption temperature was optimized. The GC separation was performed in a capillary column. Detection limits were found to be of the order of ca. 1 ng g(-1). Relative recoveries of the analytes from soils were found to be highly dependent on soil organic-matter content and on compound identity; they ranged from ca 92 to 96% for sandy soil (extraction at room temperature) and from ca 27 to 55% for peaty soil (extraction at elevated temperature). A few real-world soil samples were analyzed; the individual monoaromatic hydrocarbon content ranged from below detection limits to 6.4 ng g(-1) for benzene and 8.1 for the total of p- + m-xylene.