Efficient Tandem Synthesis of Methyl Esters and Imines by Using Versatile Hydrotalcite‐Supported Gold Nanoparticles

Efficient basic hydrotalcite (HT)‐supported gold nanoparticle (AuNP) catalysts have been developed for the aerobic oxidative tandem synthesis of methyl esters and imines from primary alcohols catalyzed under mild and soluble‐base‐free conditions. The catalytic performance can be fine‐tuned for these cascade reactions by simple adjustment of the Mg/Al atomic ratio of the HT support. The one‐pot synthesis of methyl esters benefits from high basicity (Mg/Al=5), whereas moderate basicity greatly improves imine selectivity (Mg/Al=2). These catalysts outperform previously reported AuNP catalysts by far. Kinetic studies show a cooperative enhancement between AuNP and the surface basic sites, which not only benefits the oxidation of the starting alcohol but also the subsequent steps of the tandem reactions. To the best of our knowledge, this is the first time that straightforward control of the composition of the support has been shown to yield optimum AuNP catalysts for different tandem reactions.     

Guerbet condensation of methanol with n-propanol to isobutyl alcohol over heterogeneous copper chromite/Mg–Al mixed oxides catalysts

The synthesis of isobutyl alcohol (ⁱBuOH) from methanol (MeOH) and n-propanol (PrOH) through the Guerbet condensation has been studied at 200 °C and under inert atmosphere (3.0 MPa of N₂), using a two-component heterogeneous catalytic system based on pre-activated copper chromite and Mg–Al mixed oxides deriving from hydrotalcite-type (HT) precursors with different Mg/Al ratios. All the investigated catalysts displayed a significant activity, with an almost complete selectivity to ⁱBuOH. Unlike the copper chromite/soluble sodium methoxide system, the catalysts were tolerant of the co-produced water and did not display any appreciable deactivation during the course of the reaction. The catalyst productivity was found to increase by reducing the Mg/Al ratio in the heterogeneous base, according to the increase of the fraction of medium–strong and strong basic sites which favour the aldol condensation between the aldehydes derived from MeOH and PrOH.     

Environmentally friendly one-pot synthesis of alpha-alkylated nitriles using hydrotalcite-supported metal species as multifunctional solid catalysts

A ruthenium-grafted hydrotalcite (Ru/HT) and hydrotalcite-supported palladium nanoparticles (Pd(nano)/HT) are easily prepared by treating basic layered double hydroxide, hydrotalcite (HT, Mg(6)Al(2)(OH)(16)CO(3)) with aqueous RuCl(3)n H(2)O and K(2)[PdCl(4)] solutions, respectively, using surface impregnation methods. Analysis by means of X-ray diffraction, and energy-dispersive X-ray, electron paramagnetic resonance, and X-ray absorption fine structure spectroscopies proves that a monomeric Ru(IV) species is grafted onto the surface of the HT. Meanwhile, after reduction of a surface-isolated Pd(II) species, highly dispersed Pd nanoclusters with a mean diameter of about 70 A is observed on the Pd(nano)/HT surface by transmission electron microscopy analysis. These hydrotalcite-supported metal catalysts can effectively promote alpha-alkylation reactions of various nitriles with primary alcohols or carbonyl compounds through tandem reactions consisting of metal-catalyzed oxidation and reduction, and an aldol reaction promoted by the base sites of the HT. In these catalytic alpha-alkylations, homogeneous bases are unnecessary and the only by-product is water. Additionally, these catalyst systems are applicable to one-pot syntheses of glutaronitrile derivatives.     

Influence of Mg/Al Molar Ratio on the Structures and Properties of Ru-Mg Alx Catalysts for Isomerization Linoleic Acid

With the knowledge on the significant effect of basic site and Ru on the catalytic performance of heterogeneous catalysts in the isomerization of linoleic acid to conjugated linoleic acid,a series of Ru-Mg Alx compounds with different basicity have been prepared by controlling the Mg/Al molar ratio. The results showed the catalysts with different basicity markedly influence the structure,the Ru dispersion,properties and catalytic performances for the isomerization reaction. The strong basic site is conductive to the high yield of CLA products. The strong basic site and the well-dispersion RuO_2 synergetic catalysis for the isomerization reaction,basic site and the well-dispersion RuO_2 synergetic effect are possibly via a Mg-O-Ru linkage.     

Pd-基金属-酸-碱多功能催化剂的制备及其丙酮一步法合成MIBK性能研究

甲基异丁基酮 (MIBK) 是一种重要的化学品, 广泛应用于涂料以及有机合成领域, 下游产品包括特种涂料溶剂、高品质脱蜡溶剂和高性能橡胶防老剂等. 近年来随国民经济的快速发展, 甲基异丁基酮的年需求量与价格逐年上升, 应用领域也不断拓宽. 因此, 开展 MIBK 绿色合成工艺的研究对提高原子经济性、打破国际技术壁垒以及满足国内市场需求具有重要意义. 目前生产 MIBK 最绿色、高效的生产方法是丙酮一步法, 包括缩合、脱水以及加氢等一系列反应过程, 该工艺顺利实施的关键在于所使用的催化剂. 根据丙酮一步法合成 MIBK 反应特点, 所用催化剂表面必须具备多种催化活性中 心, 从而保证缩合、脱水以及加氢反应的顺利进行, 实现从反应物到产物的高效转化. 因此, 高活性和高选择性多功能催化剂的制备是提高 MIBK 生产效率的有效途径.本文采用浸渍法将具有加氢活性的贵金属 Pd 负载在表面具有丰富酸性位点或碱性位点的固体酸或固体碱氧化物载体上, 制备了 Pd/MOx(M = Ti, Ce, Al, Si, La, Ca和Mg) 双功能催化剂, 并用于丙酮一步法合成 MIBK 反应中. 结果表明, Pd基金属-酸/碱双功能催化剂均可以催化该连串反应的进行, 其性能高于 Pd 基金属-酸双功能催化剂, 其中 Pd/MgO 催化剂上丙酮转化率为30.67%, MIBK 产率可达27.61%. 构效关系研究显示, 催化剂表面酸性位点和碱性位点对于该连串反应的各反应步骤催化性能有所不同, 其中碱性位点有利于丙酮缩合反应, 而酸性位点有利于二丙酮醇脱水反应, 且强路易斯碱性中心位点可以更好的催化缩合反应的进行, 同时中强度路易斯酸性中心位点具有最佳的催化脱水反应的能力. 此外, 表面具有最强路易斯碱性中心位点 Pd/La2O3催化剂并未表现出最高的MIBK产率, 说明在丙酮一步法合成MIBK反应中, Pd基双功能催化剂表面各位点间的协同对其催化性能具有重要的影响.本文进一步采用水热法和沉淀沉积法制备了系列MgTiOx、MgAlOx和CaTiOx二元复合氧化物 (MMO) 以及 CaMgAlOx和 TiMgAlOx三元MMO, 并以其为载体, 通过浸渍焙烧还原制备 Pd 基多功能催化剂, 并用于丙酮一步法合成MIBK反应中,发现Pd/MgAl-MMO多功能催化剂具有最高的催化活性及 MIBK 产率. 对其表面多功能位点数量进行调变, 并通过 XRD、CO2-TPD、NH3-TPD、吡啶红外、CO2红外和HRTEM等进行表征, 结果表明, 经过450 ℃焙烧酸碱中心摩尔量比为0.4的0.1%Pd/Mg3Al-MMO多功能协同催化剂三种催化活性中心位点协同作用最佳, 其丙酮转化率为38.20%, MIBK产率可达31.63%. Pd/Mg3AlMMO多功能协同催化剂三种活性位点接近性研究表明, 在多功能催化剂中分离酸中心活性位点、碱中心活性位点以及加氢活性位点后, 获得的双功能催化剂产率均明显下降, 说明Pd/Mg3Al-MMO多功能催化剂在三种活性位点相互接近时才能更好催化反应的进行. 根据多功能催化剂构效关系研究结果, 对各催化活性中心的密度及分布进行调控, 结果显示, 通过沉淀沉积法制备的Pd/Mg3Al-MMO催化剂性能进一步提高, 丙酮转化率为42.11%, 产率高达37.20%.     

Preparation of supported metal catalysts starting from hydrotalcites as the precursors and their improvements by adopting “memory effect”

Hydrotalcite-like compounds (HTlcs) can be used as the catalysts as it is since they contain various transition metal cations as the catalytically active species well dispersed on the basic support materials. Moreover, increasing numbers of the applications of HTlcs after the heat treatment have been found since the oxides with very small crystal size, stable to thermal treatments, are obtained after the calcination. The oxides possess interesting properties such as high surface area, basic properties and further form small and thermally stable metal crystallites by reduction. Moreover, the calcined oxides show a unique property, i.e., “memory effect,” which allows the reconstitution of the original hydrotalcite structure. We have developed the catalytic applications of hydrotalcites as it is and moreover the mixed oxides derived from hydrotalcites for various catalytic reactions, i.e., oxidation, dehydrogenation and reforming of hydrocarbons, and even for the reforming of methanol and the CO shift reaction. Aerobic oxidation of alcohols, Baeyer−Villiger oxidation of ketones and O₃ oxidation of oxalic acid have been successfully carried out with the Mg−Al hydrotalcites containing Ni, Fe and Cu, respectively, as the catalysts in liquid phase. In the O₃ oxidation of oxalic acid, the catalytic activity was enhanced by the “memory effect,” i.e., Mg(Cu)–Al hydrotaclite was reconstituted on the surface of Mg(Cu,Al)O periclase particles and oxalic acid was incorporated as anions in the hydrotalcite layer, resulting in an enhanced oxidation of oxalic acid. As the catalysts in the vapor phase reactions, Mg/Fe/Al mixed oxides prepared from Mg–Al(Fe) hydrotalcites and effectively catalyzed the dehydrogenation of ethylbenzene. Supported Ni metal catalysts have been prepared from Mg(Ni)–Al hydrotalcites and successfully used in the steam reforming and the oxidative reforming of methane and propane. Moreover, the Ni catalysts have been improved by combining a trace amount of noble metals by adopting the “memory effect” and used in the production of hydrogen for the PEFC under the daily startup and shutdown operation. Also starting from aurichalcite or hydrotalcite precursor as the precursor, Cu/Zn/Al catalysts with high Cu metal surface area have been prepared and successfully applied in the steam reforming of methanol and dimethyl ether, and moreover in the CO shift reaction.     

Pd-Ce-B/水滑石催化液相苯酚选择性加氢制环己酮

以Al3 /(Al3 Mg2 )摩尔比为0.2的水滑石(HT)为载体,采用还原浸渍法制备了负载型Pd-Ce-B/HT催化剂,并将其应用于液相苯酚选择性加氢制环己酮.与Pd-Ce-B/Al2O3,Pd-Ce-B/MgO和Pd-Ce-B/SiO2相比,Pd-Ce-B/HT催化剂具有高活性和高环己酮选择性.5.8%Pd-Ce-B/HT上苯酚的转化率和环己酮的选择性分别达82.0%和80.3%,显示了其潜在的工业化应用前景.根据多种表征结果,初步讨论了催化剂的构效关系以及添加剂Ce3 和载体酸碱性对催化性能的促进作用.     

Structure and base properties of calcined hydrotalcites

Five hydrotalcites with Mg/Al molar ratio range of 3-15 were prepared. The structure and basicity of Mg-Al mixed oxides (Mg(Al)O) transformed from hydrotalcites were investigated by TPD, XPS, XRD, FT-IR and NMR techniques. The results of elemental analysis and XPS indicate that Al is enriched in the surface regions of Mg(Al)0, and its amount increases with the Mg/Al molar ratio and the calcination temperature. 27Al-MAS-NMR results show that Al exists in two chemical environments: tetrahedral aluminium (Al(t)) and octahedral aluminium (Al(o)) in Mg(Al)O. The amount of Al(t) increases with the Mg/Al molar ratio and the calcination temperature. It is assumed that Al(t) may be mainly from the surface Al. Temperature-programmed desorption (TPD) of CO2 shows that the number of basic sites of Mg(Al)O samples increases with the Mg/Al molar ratio, and the maximum number of basic sites is obtained for hydrotalcite calcined at 773 K. Infrared spectra of adsorbed CO2 and B(OCH3)3 reveal that there are two kinds of     

Calcined Mg-Al Layered Double Hydroxide as a Heterogeneous Catalyst for the Synthesis of Urea Derivatives from Amines and CO2

The calcined Mg‐Al layered double hydroxides (LDHs) with a Mg/Al molar ratio of 3:1 were synthesized and characterized thoroughly by X‐ray diffraction (XRD), temperature‐programmed desorption (TPD) of CO₂, and thermogravimetric analysis (TGA). Thus the calcined Mg‐Al LDHs were used as catalyst for the catalytic synthesis of disubstituted ureas from amines and CO₂. The effects of reaction time, reaction temperature, pressure, solvent and calcined temperature on activity have been investigated. The results indicated that aliphatic amines, cyclohexylamine and benzylamine can be converted to the corresponding ureas selectively over the calcined Mg‐Al LDHs catalysts with N‐methyl‐2‐pyrrolidone (NMP) as solvent without using any dehydrating regent. The catalyst can be recycled several times with only slight loss of activity.     

氟修饰的含Ni类水滑石在甲烷部分氧化制合成气中的应用研究

通过共沉淀法合成了含Ni/Mg/Al的类水滑石,并利用水滑石的"重构性能"将F^-引入到水滑石层间。焙烧该类水滑石后得到Ni/Mg/Al/O-F催化剂,采用XRD、SEM、CO₂-TPD、H₂-TPR、N₂吸附-脱附等手段对其结构进行了表征。结果表明,焙烧后的催化剂为方镁石结构,并具有丰富的介孔,Ni/Mg/Al/O-F较之不含F^-的复合氧化物Ni/Mg/AlO具有更小的比表面积、颗粒粒径和结晶度,但是碱密度明显增大,并且在甲烷部分氧化(POM)反应中表现出更高的活性和稳定性,反应120h后,活性没有下降。这是因为F^-的引入提高了催化剂碱性和活性组分Ni的分散,从而改善了催化剂的抗积炭和烧结能力。     

The thermal decomposition of Mg-Al hydrotalcites: effects of interlayer anions and characteristics of the final structure

The thermal decomposition of hydrotalcites (HTs) with different interlayer anions in the 298-523 K region has been investigated by using transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and IR, 27Al MAS-NMR and X-ray absorption near-edge structure (XANES) spectroscopy. The thermal stability of the HT with interlayer oxalate was remarkably higher than that of HTs with interlayer carbonate; the onset temperatures for decomposition were 523 K and 473 K, respectively. It is proposed that the basicity of the interlayer anion is the key factor in the onset of dehydroxylation of the brucite-like layers: the lower the basicity, the more thermally stable the HT compound. After heat treatment at 723 K, small Mg(Al)O domains (approximately 5 nm) within the HT crystallites cause broadening of the XRD reflections. The electron diffraction pattern consists of spots and rings, due to nonrandomly oriented crystalline material. Formation of disordered bonds, caused by nonideal packing between the decomposing adjacent cation layers in the (111) direction, could explain the expanded d value in the resulting MgO-like phase observed with XRD and electron diffraction. The orientation of the Mg(Al)O domains in the heat-treated material may be crucial for the so-called "memory effect" of HTs.     

载体表面酸碱性质对无碱水溶液中Au催化的甘油氧化反应产物选择性的调控作用

甘油(GL)是一种重要的生物平台分子,通过催化选择氧化反应将其转化为具有高附加值化学品是可持续发展化学化工的重要课题之一.以Au为催化剂的GL水相选择氧化反应可以生成甘油酸(GLA)、二羟基丙酮(DHA)、羟基丙二酸(TTA)、羟基乙酸(GCA)和乳酸(LA)等多种产物.通常,该反应需要碱(NaOH)存在时才能进行,产物往往以GLA为主(选择性40%-70%),副产物主要有GCA, TTA和草酸(OA).一般认为,可溶性碱(OH-)是通过夺取GL分子中羟基上的质子而诱发反应的.尽管在Au催化的反应体系中从未检测到有甘油醛(GLD)生成, GLD和/或DHA被认为是该反应的中间物种.本课题组前期工作表明,氧化物(TiO2, Al2O3, ZrO2, CuO等)负载的纳米Au催化剂能够在无碱(无外加OH-)水溶液中选择性催化GL氧化生成DHA(而不是GLA).因此, OH-的存在与否很可能会改变水溶液中Au催化剂上GL氧化反应的途径.本文试图回答当GL的水溶液中不存在NaOH时, Au催化剂载体的表面酸碱性质是否也会对GL氧化反应的选择性产生调控作用.我们选用Mg/Al比(x)不同的MgO-Al2O3样品为Au催化剂的载体,以尿素为沉淀剂,采用沉积沉淀法制备了相应的Au/MgO-Al2O3(x)催化剂样品.采用X射线衍射、电感耦合等离子体-原子发射光谱仪、透射电镜以及N2吸附-脱附等温线等对MgO-Al2O3(x)和/或Au/MgO-Al2O3样品的物相、元素组成、Au颗粒大小以及比表面积等进行了表征分析;采用NH3和CO2程序升温脱附(TPD)分别对MgO-Al2O3(x)载体表面的酸、碱性进行了测定. NH3-TPD和CO2-TPD结果表明,随着Mg/Al比x从0增加至4.8, MgO-Al2O3(x)的表面酸量从0.94降到0.20μmol/m2,而其表面碱量却从0.05剧增至0.80μmol/m2.因此,载体中MgO含量越多或Mg/Al比越大,其酸性越弱而碱性越强.在无碱水溶液中的催化反应结果表明, Au/MgO-Al2O3(x)上GL氧化反应的主要产物为DHA, GLA以及GCA等.随着x值(催化剂表面碱性)不断增大,产物DHA的选择性从约80%下降到10%左右,而GLA的选择性却从约4%增加至约50%.当载体为酸性最强的Al2O3(x =0)时,产物DHA的选择性为最高(80%).由此可见,载体表面的酸碱性质决定了无碱水溶液中Au催化剂上的GL氧化产物的分布. 此外,当保持Au粒子的尺寸基本不变(如3.1或6.6 nm左右),而改变载体的酸碱性质时, Au/MgO-Al2O3催化GL氧化反应的活性(TOF)可相差8-9倍.本文还通过改变Au/MgO-Al2O3样品焙烧温度,制备了表面酸碱性质相同而颗粒大小不同的三个Au/MgO-Al2O3(0.2)催化剂,考察了Au粒径对GL氧化反应选择性的影响.在这三个催化剂上, Au颗粒的平均尺寸分别为2.8,3.2和6.6 nm, GL氧化反应的产物选择性近乎相同(DHA和GLA的选择性分别为65%和15%左右),但平均尺寸为6.6 nm Au粒子的催化活性(TOF)是3.2 nm Au粒子的1.6倍,2.8 nm Au粒子的2.7倍.因此,本文建立了载体表面酸碱性质与无碱水溶液中GL氧化产物选择性之间的关系,通过改变载体表面酸碱性质实现了对无碱水溶液中Au催化剂上GL氧化反应选择性的调控.尽管载体酸碱性质和Au粒子尺寸都对Au/MgO-Al2O3催化剂的本征活性有重要影响,但载体酸碱性质的影响更显著.     

＂Intelligent＂ reforming catalysts： Trace noble metal-doped Ni/Mg（A1）O derived from hydrotalcites

Trace amounts of noble metal-doped Ni/Mg(Al)O catalysts were prepared starting from Mg-Al hydrotalcites (HTs) and tested in daily start-up and shut-down (DSS) operation of steam reforming (SR) of methane or partial oxidation (PO) of propane. Although Ni/Mg(Al)O catalysts prepared from Mg(Ni)-Al HT exhibited high and stable activity in stationary SR, PO and dry reforming of methane and propane, the Ni/Mg(Al)O catalysts were drastically deactivated due to Ni oxidation by steam as purge gas when they were applied in DSS SR ofmethane. Such deactivation was effectively suppressed by doping trace amounts of noble metal on the catalysts by using a “memory effect” of HTs. Moreover, the noble metal-doped Ni/Mg(Al)O catalysts exhibited “intelligent” catalytic behaviors, i.e., self-activation and self-regenerative activity, leading to high and sustainable activity during DSS operation. Pt was the most effective among noble metals tested. The self-activation occurred by the reduction of Ni2+ in Mg(Ni,Al)O periclase to Ni0 assisted by hydrogen spillover from Pt (or Pt-Ni alloy). The self-regenerative activity was accomplished by self-redispersion of active Ni0 particles due to a reversible reductionoxidation movement of Ni between the outside and the inside of the Mg(Al)O periclase crystal; surface Ni0 was oxidized to Ni2+ by steam and incorporated into Mg(Ni2+,Al)O periclase, whereas the Ni2+ in the periclase was reduced to Ni0 by the hydrogen spillover and appeared as the fine Ni0 particles on the catalyst surface. Further a “green” preparation of the Pt/Ni/[Mg3.5Al]O catalysts was accomplished starting from commercial Mg3.5-Al HT by calcination, followed by sequential impregnation of Ni and Pt.     

Cross Aldolization Between Benzaldehyde and n-Heptaldehyde to α-Pentylcinnamaldehyde Overcalcined mg-al Hydrotalcites

Calcined Mg-Al hydrotalcites (CHT) with various Mg/Al atomic ratios were prepared and characterized by XRD, BET and TPD of carbon dioxide. The CHT catalysts were utilized for the synthesis of -pentylcinnamaldehyde (-P_c) from benzaldehyde and n-heptaldehyde in a stirred batch autoclave reactor. An increase of Mg/Al atomic ratio of CHT samples results in the apparent enhancement of catalyst basicity with concomitant decrease of surface areas. Both the catalytic activity and the -P_c selectivity increase with the catalyst basicity and the reaction temperature.     

MgO、Al_2O_3、SiO_2催化剂上湿天然气中乙烷氧化脱氢的研究(英文)

研究了ＭｇＯ、Ａｌ２Ｏ３、ＳｉＯ２催化剂对湿天然气中乙烷氧化脱氢反应的影响，发现ＭｇＯ对乙烷脱氢有较好的活性，７００Ｃ时，Ｃ２Ｈ４选择性达４１．８５％，收率达１８．７５％。考察了催化剂酸碱性对反应的影响，适当碱性的催化剂有利于反应的进行，催化剂活性顺序与碱性大小顺序相一致为ＭｇＯ＞Ａｌ２Ｏ３＞ＳｉＯ２。催化剂活性顺序与其晶格氧流动性有顺应关系。     

Preparation, Characterization of Hydrotalcites and the Catalytic Properties in Synthesis of o-Phenylphenol over Pt／CHT

Mg/Al mixed oxides with molar ratios of 2-6 of Mg to Al used as supports for platinum catalysts were obtained by the thermal decomposition method. The effect of the composition of the mixed oxides on the physicochemical properties was studied by TPD, nitrogen sorption, XRD and TG-DTA characterization methods. The synthesis of o-phenylphenol (OPP) from a dimer (obtained from cyclohexanone condensation) was investigated over Pt/CHT catalysts and compared with those over Pt/MgO and Pt/Al2O3 catalysts. These catalysts show a high activity and selectivity for OPP, with a conversion reaching 93.8% and a selectivity reaching 87.9% in some experiments. For Pt/CHTx catalysts, the calcined hydrotalcites exhibited strong base sites, which were necessary to catalyze the synthesis of OPP.     

Thermogravimetry study of the ester interchange of sunflower oil using Mg/Al layered double hydroxides (LDH) impregnated with potassium

Mg/Al layered double hydroxides (LDH) containing KI were synthesized and tested as basic heterogeneous catalysts for transesterification of sunflower oil, in order to obtain biodiesel. The process was carried out using reflux with 15:1 molar ratio of methanol to sunflower oil, and catalyst concentration of 2 mass%. The characterization of sunflower oil and biodiesel was accomplished according to ASTM and EN standard methods. The gas chromatographic and TG/DTG profiles were evaluated, and the results of yield and conversions were compared. The gas chromatographic analysis showed that the catalysts were effective in converting vegetable oil into biodiesel, specially using LDH catalysts modified with KI and molar ratio Mg/Al = 1, with conversions higher than 99 % indicating the strong influence of the chemical composition and controlled basicity, due to the presence of potassium in the structure of the catalyst.     

甲烷干重整反应用Ni-Ru/MgAl类水滑石催化剂的研究

采用焙烧记忆法分别制备Ni/Mg Al O和NiRu/Mg Al O类水滑石催化剂用于甲烷干重整反应.利用XRD、TPR、TG、XPS、CO2-TPD、TEM等表征催化剂的结构及失活特征,发现在Ni/Mg Al O中添加Ru,有利于增加催化剂表面Ni含量,并促进Ni2+的还原.不同Mg/Al比双金属催化剂中,7Ni-0.15Ru/Mg2.5Al催化剂具有较高的催化活性,这归结为该催化剂适宜的碱性、较高表面Ni含量以及小尺寸的Ni0物种.添加Ru明显抑制Ni/Mg Al O催化剂表面的丝状碳的形成.而7Ni-0.15Ru/Mg2.5Al较强的抗积碳性能与其较小Ni0晶粒尺寸及适宜催化剂碱性有关.     

硝酸镁在γ-Al2O3上的热分解及MgO/γ-Al2O3

研究了不同载量时Mg(NO     

Diatomite-supported Pd-M (M=Cu, Co, Ni) bimetal nanocatalysts for selective hydrogenation of long-chain aliphatic esters

Diatomite supported Pd-M (M=Cu, Co, Ni) bimetal nanocatalysts with various metal compositions were prepared and characterized by means of X-ray diffraction, transmission electron microscopy, and X-ray photoelectron spectroscopy. It was demonstrated that the metal nanoparticles were uniformly distributed on the support, and their size was centered around 8nm with a relatively narrow size distribution. The catalysts were used to catalyze hydrogenation of long-chain aliphatic esters, including methyl palmitate, methyl stearate, and methyl laurate. It was indicated that the all diatomite-supported Pd-based bimetal catalysts were active to the selective hydrogenation of long-chain esters to corresponding alcohols at 270°C, originated from the synergistic effect between the metal particles and the diatomite support. For the selective hydrogenation of methyl palmitate, Pd-Cu/diatomite with metal loading of 1% and Pd/Cu=3 displayed the highest performance, giving a 1-hexadecanol yield of 82.9% at the substrate conversion of 98.8%.