Estimation of source spectra profiles and simultaneous determination of polycomponent in mixtures from ultraviolet spectra data using kernel independent component analysis and support vector regression

A method that use kernel independent component analysis (KICA) and support vector regression (SVR) was proposed for estimation of source ultraviolet (UV) spectra profiles and simultaneous determination of polycomponents in mixtures. In KICA-SVR procedure, the UV source spectra profiles were estimated using KICA, then the mixing matrix of the components were calculated using the estimated sources, and the calibration model was build using SVR based on the calculated mixing matrix. A simulated UV dataset of three-component mixtures was used to test the ability of KICA for estimating source spectra profiles from spectra data of mixtures. It was found that KICA has the potential power to estimate pure UV spectra profiles, and correlation coefficient of estimated sources correspond to the real adopted ones are better compared with that by FastICA and Infomax ICA. An UV dataset of polycomponent vitamin B was processed using the proposed KICA-SVR method. The results show that the estimated source spectra profiles are correlative with the real UV spectra of the components and chemically interpretable, and accurate results were obtained.     

Rapid estimation of global sugars by UV photodegradation and UV spectrophotometry

The UV/UV method developed for the measurement of specific wastewater pollution parameters (ammonium, Kjeldahl nitrogen, total phosphorus) is adapted to the determination of sugars in fruit juices and soft drinks. The procedure is based on the UV spectrophotometric detection of by-products of UV photodegradation of carbohydrates. Time of analysis is greatly reduced by using specific pH conditions and diluted samples.     

Photoprotective and Antigenotoxic Effects of the Flavonoids Apigenin,Naringenin and Pinocembrin

This work evaluated the photoprotective and antigenotoxic effects against ultraviolet B (UVB) radiation of flavonoid compounds apigenin, naringenin and pinocembrin. The photoprotective efficacy of these compounds was estimated using in vitro photoprotection indices, and the antigenotoxicity against UVB radiation was evaluated using the SOS chromotest and an enzymatic (proteinase K/T4 endonuclease V enzyme) comet assay in UV‐treated Escherichia coli and human (HEK‐293) cells, respectively. Naringenin and pinocembrin showed maximum UV‐absorption peak in UVC and UVB zones, while apigenin showed UV‐absorption capability from UVC to UVA range. These compounds acted as UV filters reducing UV‐induced genotoxicity, both in bacteria and in human cells. The enzymatic comet assay resulted highly sensitive for detection of UVB‐induced DNA damage in HEK‐293 cells. In this work, the photoprotective potential of these flavonoids was widely discussed.     

Dansyl and dabsyl analytical constructs as tools for the accurate estimation of compounds in solid-phase synthesis

The presence of dansyl or dabsyl chromogenic moieties in a solid-phase analytical construct, an assembly of linkers/spacers/sensitizers for improving analytical characterization, allows the accurate estimation of products from solid-phase synthesis by UV detection during liquid chromatography-mass spectrometry analysis in the cleavage solution. The spectroscopic properties of dansylated molecules have been evaluated to verify the "compound-independent UV absorption" necessary for using the chromophore in the accurate estimation. First, measurements on commercial dansylated compounds were made, then a series of construct-like molecules were prepared by solution-phase synthetic procedures and their UV properties were determined. Compound calibration curves were determined, and UV absorption was shown to be both proportional to the compound concentration and compound-independent. An example of a dansyl construct derivative was then prepared on a polymeric matrix, and an accurate estimation using the calibration curves was carried out in the cleavage solution. Good agreement was found between the calculated amount of released compound using the UV calibration curves and the calculated amount using both (1)H NMR and LC/chemiluminescent nitrogen detection quantitative techniques. Preliminary studies using the dabsyl moiety as an improved chromophore with higher wavelength and extinction coefficient are also reported.     

Environmental UV‐A and UV‐B Threshold Doses for Apoptosis and Necrosis in Humans Fibroblasts¶

Apoptosis involves a highly organized and programmed series of events aimed at maintaining genomic stability by eliminating defective host cells. The purpose of this study was to determine the threshold doses and environmental UV‐A and UV‐B exposure times necessary to produce apoptosis and necrosis in the normal cells of a human fibroblast cell line. Enviromental UV‐A and UV‐B doses were measured over a 6 year period with a four‐channel UV radiometer. The fibroblasts were irradiated once using an Oriel UV Solar Simulator with six doses of environmentally‐based UV. Doses corresponded to 0,11,19,23 and 45 min of average environmental UV‐A and UV‐B radiation at solar noon in Puerto Rico. The Annexin‐V binding method was used to differentiate between normal fibroblasts and apoptotic or necrotic fibroblasts. The threshold dose from apoptosis to necrosis was found between 24–28 kJ/m², which corresponded to 19 and 23 min of environmental UV‐A and UV‐B exposure. This study provides the first data that specify the environmental threshold doses of UV‐A and UV‐B at which human fibroblasts undergo apoptosis and necrosis. These results may provide valuable dose‐response thresholds for apoptosis and necrosis for future mechanistic studies and baseline data for skin cancer prevention programs.     

Influence of spectral and angular sensitivity on the readout of biological dosimeters

Biological systems used as biological dosimeters can possess different angular sensitivities from the detectors usually used in physical devices. A simple experimental setup has been developed and used to measure the angular sensitivity of uracil thin-layer biological dosimeters. Results of angular sensitivity measurements for uracil thin-layer dosimeters are presented using a Xe arc lamp as the UV source. According to the experiments described here, uracil thin-layer dosimeters show a cosine-type angular dependence. In several indoor experiments broadband UV meters are used to control the applied dose rate from a given artificial UV source. The experimental setup has been designed and used to verify experimentally the importance of spectral and angular sensitivity differences of biological and physical UV meters applied in biological experiments. Model calculations for two different irradiation systems, using different geometrical arrangements of artificial UV sources, are also presented. For these arrangements relative dose rates that could be measured with dosimeters of arbitrary spectral, but different angular sensitivity have been calculated.     

Separation of Sulfur Species in Water by Co-Electroosmotic Capillary Electrophoresis with Direct and Indirect UV Detection

Co-electroosmotic capillary electrophoresis (co-CZE) with both direct and indirect UV detection was investigated for the separation of sulfur species. With direct UV detection, the separation of S₂O^2? ₃, S₂O^2? ₄ was possible using 20 mM phosphate electrolyte containing 0.75 mM tetradecyltrimethylammonium bromide (TTAB) and 15% acetonitrile. To obtain optimal peak shape and sensitivity using indirect UV detection, a range of background electrolytes (BGEs), including benzoate, phthalate, 2,6-pyridinedicarboxylate (2,6-PDCA) and trimellitate, were examined as the BGEs. Of all the BGEs, 2,6-PDCA gave high selectivity and indirect UV response due to its mobility matching to that of sulfur species and its high absorptivity. Detection limits in range of 3-6 μM were obtained using either direct UV or indirect UV detection. The proposed CZE methods were used for the determination of sulfur species in water samples, and provided fast separation of sulfur species in less than 5 min.     

Synergistic effect of UV and l-ascorbic acid on the reduction of graphene oxide: Reduction kinetics and quantum chemical simulations

A photochemical strategy for eco-friendly reduction of graphene oxide (GO) was developed by using l-ascorbic acid (L-AA) as a photosensitive reducing agent. L-AA was excited and oxidized with deprotonation by UV irradiation (254 nm) and the proton coupled electron transfer induces chemical reduction of GO. This photochemical process is quite eco-friendly and scalable, and the reduction kinetics and degree of GO were highly enhanced. To understand the improved reduction power by UV light, the redox properties of L-AA in the ground and excited states were characterized by using quantum chemical simulations. Based on the results, we clearly demonstrated the mechanism how UV irradiation considerably enhances the reducing power of L-AA for the reduction of GO.     

Determining an Effective UV Radiation Exposure Time for Vitamin D Synthesis in the Skin Without Risk to Health: Simplified Estimations from UV Observations

UV radiation contains erythemally weighted UV, as well as UV that synthesizes vitamin D₃. Here, we attempted to determine the relationship between these factors by numerical simulation of atmospheric parameters, such as total ozone, using a simplified “SMART2” model for radiative transfer. Both forms of UV were almost linearly correlated with each other for a comparably large UV radiation exposure, larger than UV Index ~1.6. If erythemally weighted UV, which carries a risk of sunburn, is known, the amount of UV exposure needed for vitamin D synthesis in the epidermis can be estimated using this relationship. The production of 10 μg (400 IU) of vitamin D per day takes approximately 1/3 of the time needed to reach the minimal erythemal dose (MED) for an effective skin area of 600 cm² for skin phototype III. For an area of 1200 cm², 1/6 of that exposure time suffices. From a UV Index that is commonly used, the risks and benefits can be evaluated using this linear relationship, which will enable people to effectively manage their UV exposure and consider the risks and benefits to optimize health outcomes.     

UV Inactivation of Common Pathogens and Surrogates Under 222 nm Irradiation from KrCl* Excimer Lamps

Germicidal ultraviolet (UV) devices have been widely used for pathogen disinfection in water, air, and on food and surfaces. Emerging UV technologies, like the krypton chloride (KrCl*) excimer emitting at 222 nm, are rapidly gaining popularity due to their minimal adverse effects on skin and eyes compared with conventional UV lamps emitting at 254 nm, opening opportunities for UV disinfection in occupied public spaces. In this study, inactivation of seven bacteria and five viruses, including waterborne, foodborne and respiratory pathogens, was determined in a thin-film aqueous solution using a filtered KrCl* excimer emitting primarily at 222 nm. Our results show that the KrCl* excimer can effectively inactivate all tested bacteria and viruses, with most microorganisms achieving more than 4-log (99.99%) reduction with a UV dose of 10 mJ cm⁻². Compared with conventional UV lamps, the KrCl* excimer lamp exhibited better disinfection performance for viruses but was slightly less effective for bacteria. The relationships between UV sensitivities at 222 and 254 nm for bacteria and viruses were evaluated using regression analysis, resulting in factors that could be used to estimate the KrCl* excimer disinfection performance from well-documented UV kinetics using conventional 254 nm UV lamps. This study provides fundamental information for pathogen disinfection when employing KrCl* excimers.     

Thermal and mechanical properties of UV irradiated collagen/chitosan thin films

The thermal and mechanical properties of collagen/chitosan blends before and after UV irradiation have been investigated using thermal analysis and mechanical (Instron) techniques. Comparisons were made with the thermal and mechanical properties of both collagen and chitosan films. Air-dried collagen, chitosan and collagen/chitosan films were exposed to UV irradiation (wavelength 254 nm) for different time intervals. Thermal properties of collagen/chitosan blends depend on the composition of the blend and are not significantly altered by UV irradiation.Mechanical properties such as ultimate tensile strength and ultimate percentage of elongation were much better for collagen films than for collagen/chitosan films. The results have shown that the mechanical properties of the blends were greatly affected by the duration of UV irradiation. Ultimate tensile strength and ultimate percentage elongation decreased after UV irradiation of the blend. Increasing UV irradiation leads to an increase in Young's modulus of the collagen/chitosan blend.     

Outdoor and accelerated weathering studies of bisphenol A polycarbonate

The influence of outdoor weathering on the degradation rate of unstabilized bisphenol A polycarbonate (BPA-PC) films is investigated and compared to the results found for indoor accelerated weathering conditions, using UV and IR spectroscopy. At the same dosage, changes in UV and IR were larger for the accelerated than for the outdoor weathered samples, this could be explained by the lower degradation temperature during outdoor exposures. The difference between outdoor and accelerated weathering is according to the IR measurement larger than according to the UV measurement. This difference is ascribed to difference in wavelength distribution between the spectra of the light emitted in the accelerated test and from the terrestrial sunlight. The larger difference for the IR results than for the UV results suggests a difference in ratio between photo-Fries rearrangements and photo-oxidation reaction between both exposures.     

Separation and detection of angiotensin peptides by Cu(II) complexation and capillary electrophoresis with UV and electrochemical detection

The use of capillary electrophoresis (CE) with on-capillary Cu(II) complexation for the determination of angiotensin and its metabolites is described. The resulting copper-peptide complexes can be detected using either UV or electrochemical (EC) detection. Optimal reaction and separation conditions for the angiotensin peptides were first determined using CE with UV detection. With UV detection, the limit of detection (signal-to noise ratio S/N = 3) for native angiotensin II was 18 microM, while the limit of detection (LOD) obtained for the copper-angiotensin II complex is 2 microM. CE with EC detection was then evaluated, yielding significantly lower LODs--2 microM for native angiotensin II and 200 nM for the copper-angiotensin II complex. The addition of copper to the run buffer improved the separation and sensitivity for both CE-UV and CE-EC detection. The method was demonstrated by monitoring the conversion of angiotensin I to angiotensin II in plasma via angiotensin-converting enzyme (ACE) and subsequent inhibition of ACE by captopril.     

Fabrication and optical characterization of imprinted broad‐band photonic films via multiple gradient UV photopolymerization

A structured broad‐band photonic film is fabricated by a novel method using multiple gradient UV‐induced polymerization in the presence of cholesteric liquid crystals (CLCs). Here, imprinting and broadening of the reflection band of chiral nematic mesophase cells are achieved via controlled UV polymerization. The intensity gradient of UV light is modified by the distance between UV lamp and sample cell, which affects the polymerization rate and leads to the formation of imprinted helical constructions with different pitches. In this study, a comparison of new design process with traditional UV polymerization process is carried out. After seven cycles of gradient UV polymerization, the imprinted photonic construction exhibited a broadened reflection band and Bragg reflection, even for isotropic materials. Because of this, the reflection bandwidth showed a 70% improvement. Additionally, two stacked imprinted cells with different pitches can reflect incident light with a bandwidth over the visible wavelength range of 480–680 nm. A broad‐band photonic polymer film can be imprinted using multiple gradient UV photopolymerization in the presence of CLCs. Forming a UV intensity gradient and controlling the rate of photopolymerization are key factors in broadening the reflection band. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017, 55, 1427–1434     

Enhancement of detection sensitivity and cleanup selectivity for tobramycin through pre-column derivatization.

Reversed-phase high-performance liquid chromatography, UV detection and reversed-phase solid-phase extraction (SPE) as analytical methods for pharmaceutical compounds face a challenge when the compound is rather polar and lack UV absorptivity. A good example is tobramycin. To overcome these problems, a method has been developed using pre-column derivatization of tobramycin with o-phthalaldehyde and automated with an autosampler with microrobotic routines. The detection enhancement of the derivatives was achieved by using fluorescence detection which was forty times more sensitive than using UV detection. Recovery studies of standards and spiked serum samples show that pre-SPE derivatization significantly enhances the recoveries (by at least a factor of 3) and the quality of cleanup over post-SPE derivatization.     

Experimental and theoretical UV characterizations of acetylacetone and its isomers

Cryogenic matrix isolation experiments have allowed the measurement of the UV absorption spectra of the high-energy non-chelated isomers of acetylacetone, these isomers being produced by UV irradiation of the stable chelated form. Their identification has been done by coupling selective UV-induced isomerization, infrared spectroscopy, and harmonic vibrational frequency calculations using density functional theory. The relative energies of the chelated and non-chelated forms of acetylacetone in the S0 state have been obtained using density functional theory and coupled-cluster methods. For each isomer of acetylacetone, we have calculated the UV transition energies and dipole oscillator strengths using the excited-state coupled-cluster methods, including EOMCCSD (equation-of-motion coupled-cluster method with singles and doubles) and CR-EOMCCSD(T) (the completely renormalized EOMCC approach with singles, doubles, and non-iterative triples). For dipole-allowed transition energies, there is a very good agreement between experiment and theory. In particular, the CR-EOMCCSD(T) approach explains the blue shift in the electronic spectrum due to the formation of the non-chelated species after the UV irradiation of the chelated form of acetylacetone. Both experiment and CR-EOMCCSD(T) theory identify two among the seven non-chelated forms to be characterized by red-shifted UV transitions relative to the remaining five non-chelated isomers.     

Comparison of femtosecond laser and continuous wave UV sources for protein-nucleic acid crosslinking

Crosslinking proteins to the nucleic acids they bind affords stable access to otherwise transient regulatory interactions. Photochemical crosslinking provides an attractive alternative to formaldehyde-based protocols, but irradiation with conventional UV sources typically yields inadequate product amounts. Crosslinking with pulsed UV lasers has been heralded as a revolutionary technique to increase photochemical yield, but this method had only been tested on a few protein-nucleic acid complexes. To test the generality of the yield enhancement, we have investigated the benefits of using approximately 150 fs UV pulses to crosslink TATA-binding protein, glucocorticoid receptor and heat shock factor to oligonucleotides in vitro. For these proteins, we find that the quantum yields (and saturating yields) for forming crosslinks using the high-peak intensity femtosecond laser do not improve on those obtained with low-intensity continuous wave (CW) UV sources. The photodamage to the oligonucleotides and proteins also has comparable quantum yields. Measurements of the photochemical reaction yields of several small molecules selected to model the crosslinking reactions also exhibit nearly linear dependences on UV intensity instead of the previously predicted quadratic dependence. Unfortunately, these results disprove earlier assertions that femtosecond pulsed laser sources provide significant advantages over CW radiation for protein-nucleic acid crosslinking.     

A comparison of 2-D chromatography separations using UV and (18)O quantification of proteins in similar proteomes

Proteins present in two mitochondria preparations were separated by 2-D chromatography using the ProteomeLab PF-2D Protein Fractional System, protein fractionation in two dimensions (PF-2D). The proteins in each first-dimension fraction were determined by trypsinization and LC-MS/MS. Chromatography peaks were quantified by UV detection using the "Mapping Tools" software (Beckman). The proteins present in UV detected peaks were trypsinized and identified by automated MS/MS sequencing. Relative amounts of the proteins present in the equivalent peak for each sample were assessed by comparison of the intensities of the constituent peptides and a predicted PF-2D value was calculated from the total ion count (TIC) for each peptide. Relative quantification for (18)O labeled peptides was performed using the ZoomQuant (v1.43b) software [1, 2]. We found that the chromatography peaks detected by UV generally contained several proteins. Using (18)O labeling we determined that in each peak the ratios of the constituent proteins were different. When these ratios were normalized using the TIC to account for abundance, the resulting ratio corresponded to that determined by UV. The predicted value for the PF-2D score corresponded to the observed value for each peak irrespective of the number or proteins detected.     

Assessment of UV Biological Spectral Weighting Functions for Phenolic Metabolites and Growth Responses in Silver Birch Seedlings

In research concerning stratospheric ozone depletion, action spectra are used as biological spectral weighting functions (BSWFs) for describing the effects of UV radiation on plant responses. Our aim was to evaluate the appropriateness of six frequently used BSWFs that differ in effectiveness with increasing wavelength. The evaluation of action spectra was based on calculating the effective UV radiation doses according to 1–2) two formulations of the generalized plant action spectrum, 3) a spectrum for ultraviolet induced erythema in human skin, 4) a spectrum for the accumulation of a flavonol in Mesembryanthemum crystallinum , 5) a spectrum for DNA damage in alfalfa seedlings and 6) the plant growth action spectrum. We monitored effects of UV radiation on the concentration of individual UV absorbing metabolites and chlorophyll concentrations in leaves and growth responses of silver birch ( Betula pendula ) seedlings. Experiments were conducted outdoors using plastic films attenuating different parts of the UV spectrum. Chlorophyll concentrations and growth were not affected by the UV treatments. The response to UV radiation varied between and within groups of phenolics. In general, the observed responses of phenolic groups and individual flavonoids were best predicted by action spectra extending into the UV-A region with moderate effectiveness.     

Polymerization of Blending Cholesteryl Acrylate and Methyl Phenyl Benzoyl Acrylate

Liquid crystal is a material which is between solid and liquid phase and commonly called mesophase. Blends of liquid crystal are of great interest because of their unique optical properties. Blending in this study using two monomers of liquid crystal were cholesteryl acrylate and methyl phenyl benzoyl acrylate. The polymerization process using uv curing techniques by irradiation UV ray and without irradiation UV ray. Polymerization of blending liquid crystal acrylate using initiator 2-hydroxy-2-methyl-1-phenylpropane. Based on peak at GPC curve of polymerization by irradiation UV ray, type of that polymer is copolymer. Therefore the polymerization without UV ray, type of that polymer is homopolymer. SEM images of liquid crystal acrylate polymer showed lamella chain models that are characteristic of a polymer chains. Type of polymer liquid crystal acrylate was the type of Side Chain Liquid Crystalline Polymers (SCLCPs). Therefore acrylate polymer liquid crystal in this research has semi-crystalline phase, which contained crystalline phase and amorphous phase on the XRD pattern. The results of FT-IR spectroscopic characterization of the two monomers showed a peak at the wave number of 1600.43 cm ^-1 and 1622.86 cm^-1 which indicates a double bond (C=C) were obtained from acrylation. While the spectroscopy on the product blending the wave number of the peak regions is reduced that shows that carbon double bonds (C=C) in the acrylate group has polymerized. It also strengthened with a very sharp peak for CC functional groups on the wave number of 2855.15 cm^-1. The results of this study indicate that the liquid crystal polymer acrylic polymerization results with radiation UV ray and without UV ray, respectively absorb light in the UV wavelength region 363 nm and 351 nm.