Layer-by-layer deposition of bimetallic nanoshells on functionalized polystyrene beads

Bimetallic nanoshells on functionalized polystyrene beads have been fabricated through a layer-by-layer deposition technique exploiting electrostatic interaction. The synthesis has been achieved through the immobilization and successive reduction of the corresponding precursor ions. It has been shown that the thickness of the shell can be controlled by a number of cyclic depositions of respective metals onto the surface of the polystyrene beads.     

Layer-by-layer surface modification of functional nanoparticles for dispersion in organic solvents

In order to prepare SiO(2) nanoparticles that are dispersible in various organic solvents, an anionic surfactant 1, which branches into a hydrophobic chain and a hydrophilic chain, was adsorbed on to SiO(2) nanoparticles through a layer-by-layer surface modification route using polyethyleneimine (PEI). First, the relationship among the additive content of PEI, adsorbed content of PEI, and the redispersion stability of the SiO(2) nanoparticles in water was investigated. While almost the entire PEI was adsorbed when the additive PEI content was lower than 67 mg/g of SiO(2), the adsorbed content of PEI became saturated when the additive content was increased above 90 mg/g of SiO(2). SiO(2) nanoparticles that were saturated with PEI could be redispersed into water at sizes close to their primary particle size without the large-scale formation of aggregates. Next, the anionic surfactant 1 was adsorbed on the SiO(2) nanoparticles by using a SiO(2) aqueous suspension saturated with adsorbed PEI. It was found that the adsorbed content of 1 increased almost linearly as the additive content was increased when the additive condition was below 1400 mg/g of SiO(2). Furthermore, SiO(2) nanoparticles adsorbed with 80 mg/g of SiO(2) of PEI and 810 mg/g of SiO(2) of 1 could be dispersed into various organic solvents with different polarities. This layer-by-layer modification technique can also be applied to Ag nanoparticles in order to prepare Ag nanoparticles that can be dispersed in various organic solvents.     

Effect of magnesium ions on oriented growth of calcite on carboxylic acid functionalized self-assembled monolayer

The combined effect of templating and solution additives on calcite crystallization was studied. Self-assembled monolayers of mercaptoundecanoic acid supported on silver, as templates, induced the uniform, oriented nucleation of calcite from the (012) plane. The presence of Mg2+ in the crystallizing solution affected the crystal growth dramatically, due to the selective Mg binding to the calcite planes roughly parallel to the c-axis. Highly homogeneous arrays of oriented crystals with characteristic sizes, shapes, and morphology, depending on the relative concentration of Mg and Ca ions, were synthesized.     

Crystal growth of nanoporous metal organic frameworks

Nanoporous metal organic frameworks (MOFs) form one of the newest families of crystalline nanoporous material that is receiving worldwide attention. Successful use of MOFs for application requires not only development of new materials but also a need to control their crystal properties such as size, morphology, and defect concentration. An understanding of the crystal growth processes is necessary in order to aid development of routes to control such properties of the crystallites. In this Perspective article we aim to provide a short overview of the current work and understanding concerning the nucleation and growth processes of nanoporous MOFs and how this work may be expanded upon to further our comprehension of this subject. We also focus heavily on in situ studies that provide real time information on the developing materials and generally provide the most conclusive findings on the processes under investigation.     

Aggregation-governed oriented growth of inorganic crystals at an organic template

X-ray studies performed during the growth of CdCO(3) and MnCO(3) crystals from supersaturated aqueous solutions, at fatty acid monolayer templates, reveal that the nucleates are nearly three-dimensional powders below a threshold supersaturation. However, at higher supersaturations, the crystals are preferentially oriented with the {0 1 2} direction vertical. Scanning electron microscope images of samples transferred to substrates show discrete crystals at low concentrations, while at higher concentrations the crystals self-aggregate to form linear chains and sheets. The authors speculate that preferential alignment at the organic-inorganic interface is enhanced as a consequence of oriented aggregation of crystals. The role of monolayer-ion interactions in governing the morphologies and the resulting orientation of the inorganic nucleate is discussed.     

Binary mixtures of metal compounds as flame retardants for organic polymers

Studies have been made of the effect on the flammability of thermoplastic polymers of the partial or total replacement of one metal compound by another in the presence also of a suitable halogen compound; particular attention has been paid to systems where the primary flame retardant is antimony(III) oxide. With each binary metal compound system investigated, ten different compositions have been chosen so as to provide a symmetrical arrangement of points within a triangular design; resulting calculated values of the limiting oxygen index for each polymer-flame retardant system for a given polymer are shown as a graphical contour analysis. Comprehensive studies of several systems show that both iron(III) oxide and aluminium oxide monohydrate can significantly enhance the flame-retardant action of antimony(III) oxide but that several other metal compounds, although not as effective as Sb₂O₃, may nevertheless be used as adequate partial replacements for it. The Fe₂O₃-SnO₂-H₂O system can also act as an effective flame retardant under certain conditions. The SnOZnO system perhaps best illustrates the importance of the polymer substrate and of the total additive loading as factors controlling the flame-retardant effectiveness. For all the systems studied, however, ABS is a much better substrate than HDPE. The results of a reasonably detailed study of the flame retardance conferred by several different compositions of a binary metal compound mixture give a much more reliable indication of the effects on polymer flammability of the constituent metal compounds than are obtained simply by replacement of a given concentration of one compound by another.     

Construction of highly oriented crystalline surface coordination polymers composed of copper dithiooxamide complexes

Layer-by-layer bottom-up crystal engineering of metal-organic crystals at the surface of sapphire or glass from organic (rubeanic acid and derivatives) and inorganic (Cu(2+)) components which when mixed in solution form instantly an amorphous solid with high proton conduction.     

氨基功能化的金属有机框架与模型燃油中含氮化合物的结合作用

合成了金属有机骨架MIL-53(Al)和MIL-53(Al)-NH_2,并且将其作为吸附剂去除油品中的含氮化合物(喹啉和吡咯)。采用X射线衍射(XRD)、扫描电镜(SEM)、FT-IR光谱以及热重分析等对两种吸附剂进行了表征。结果表明,MIL-53(Al)-NH_2能够快速地吸附油品中的喹啉/吡咯并且显示了较高的吸附容量,但MIL-53(Al)对喹啉/吡咯的吸附容量较低,原因是MIL-53(Al)-NH_2和喹啉之间存在有利的氢键结合,但MIL-53(Al)-NH_2与吡咯的氢键作用相对较低。研究了影响吸附容量的因素,包括吸附时间和温度。采用准一级和准二级动力学模型拟合了喹啉和吡咯的吸附数据,研究了MIL-53(Al)-NH_2对喹啉和吡咯的吸附等温线和吸附热力学。通过简单的溶剂洗涤使得MIL-53(Al)-NH_2再生,并重新用于吸附过程。     

Dielectric dispersion of oriented polymers

Summary Expressions have been derived for the tensor of the complex dielectric permitivity of an oriented polymer containing polar groups in the main chain. The relevant intramolecular and intermolecular interactions have been assumed to be independent of the degree of orientation; the anisotropy of dielectric permitivity is expected to be given only by the orientation of local equilibrium positions of the dipoles. For the low-temperature dispersion of a polymer oriented by cold-drawing, both the spectra of relaxation times and the magnitudes of the components of the dielelectric permitivity tensor have been calculated. Relation between the calculated values and the dipole-dipole interaction parameters, diffusion coefficients and average dipole-chain angle are given.

---

Zusammenfassung Es wurden Ausdrücke für den komplexen Tensor der Dielektrizitätskonstantante an orientierten Polymeren, die polare Gruppen in der Hauptkette enthalten, abgeleitet. Die maßgebenden intra- und intermolekularen Wechselwirkungen wurden als unabhängig vom Orientierungsgrad angenommen; die Anisotropie der Dielektrizitätskonstante dürfte nur durch die Orientierung lokaler Gleichgewichtspositionen der Dipole gegeben sein. Für die Tieftemperaturdispersion eines kalt verstreckten Polymeren wurden das Spektrum der Relaxationszeiten und die Relaxationsstärken des Tensors berechnet. Beziehungen zwischen berechneten Werten und den Dipol-Dipol-Wechselwirkungsparametern, Diffusionskoeffizienten und den mittleren Winkel zwischen Dipol und Kette sind angegeben.

---

---

With 5 figures     

Silicon surface modification with trialkoxysilyl‐functionalized star‐shaped polymers

The synthesis of trimethoxysilane end‐capped linear polystyrene (PS) and star‐branched PS and subsequent silicon (Si) surface modification with linear and star polymers are described. Trimethoxysilane terminated PS was synthesized using sec‐butyl lithium initiated anionic polymerization of styrene and subsequent end‐capping of the living anions with p‐chloromethylphenyl trimethoxysilane (CMPTMS). ¹H and ²⁹Si NMR spectroscopy confirmed the successful end‐capping of polystyryllithium with the trimethoxysilane functional group. The effect of a molar excess of end‐capper on the efficiency of functionalization was also investigated, and the required excess increased for higher molar mass oligomers. Acid catalyzed hydrolysis and condensation of the trimethoxysilane end‐groups resulted in star‐branched PS, and NMR spectroscopy and SEC analysis were used to characterize the star polymers. This is the first report of core‐functionalized star‐shaped polymers as surface modifiers and the first comparative study showing differences in surface topography between star and linear polymer modified surfaces. Surface‐sensitive techniques such as ellipsometry, contact angle goniometry, and AFM were used to confirm the attachment of star PS, as well as to compare the characteristics of the star and linear PS modified Si surfaces. The polymer film properties were referenced to polymer dimensions in dilute solution, which revealed that linear PS chains were in the intermediate brush regime and the star‐branched PS produced a surface with covalently attached chains in the mushroom regime. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3655–3666, 2005     

Patterned growth of large oriented organic semiconductor single crystals on self-assembled monolayer templates

This work demonstrates a method for inducing site-specific nucleation and subsequent growth of large oriented organic semiconductor single crystals using micropatterned self-assembled monolayers (SAMs). We demonstrate growth of oriented, patterned, and large organic semiconductor single crystals for potential use in organic electronic devices. The control over multiple parameters in a single system has not yet been reported. The ability to control various aspects of crystal growth in one system provides a powerful technique for the bottom-up fabrication of organic single-crystal semiconductor devices.     

Improvement of interfacial adhesion of biodegradable polymers coated on metal surface by nanocoupling

A method of securing the adhesion of biodegradable polymer coating was investigated for drug-eluting metal stents, using surface-initiated ring-opening polymerization (SI-ROP) of L-lactide. Introduction of oligolactide on the stainless steel (SS) surface was successful and the thickness of the oligolactide grafts remained on the nanometer scale, as determined by ellipsometry. The presence of an oligolactide graft was also identified using attenuated total reflection-Fourier transform infrared (ATR-FTIR) and electron spectroscopy for chemical analysis (ESCA). On top of the grafts, poly(D,L-lactide-co-glycolide) (PLGA) coating was carried out on different substrates such as SS control, plasma-treated SS, and lactide-grafted (referred to as a nanocoupled) SS using electrospraying. When the adhesion forces were measured with a scratch tester, the nanocoupled SS showed the strongest interfacial adhesion between polymer coating layer and metal substrate. The outcome of the peel-off test was also consistent with the result of the scratch test. When degradation behavior of the polymer coating in vitro was examined for up to 4 weeks in a continuous fluid flow, the SEM images demonstrated that polymer degradation was obvious due to hydration and swelling of the polymer matrix. Although the matrix completely disappeared after 4 weeks for SS control and plasma-treated substrates, the nanocoupled SS was persistent with some polymer matrix. In addition, the release profiles of SRL-loaded PLGA coating appeared slightly different between control and nanocoupled groups. This work suggested that the concept of nanocoupling remarkably improved the interfacial adhesion stability between metal surface and polymer layer and controlled drug release, and showed the feasibility of drug-eluting stents.     

Self-assembled monolayer of organic iodine on a Au surface for attachment of redox-active metal clusters

The attachment of a bifunctional iodo-organo-phosphinate compound to gold (Au) surfaces via chemisorption of the iodine atom is described and used to chelate a redox-active metal cluster via the phosphinate group. XPS, AFM, and electrochemical measurements show that (4-iodo-phenyl)phenyl phosphinic acid (IPPA) forms a tightly bound self-assembled monolayer (SAM) on Au surfaces. The surface coverage of an IPPA monolayer on Au was quantified by an electrochemical method and found to be 0.40 +/- 0.03 nmol/cm2, roughly corresponding to 0.4 monolayers. We show that the Au/IPPA SAM, but not the underivatized Au, adsorbs Mn4O4(Ph2PO2)6 from solution by a phosphinate exchange reaction to yield Au/IPPA/Mn4O4(Ph2PO2)5 SAM. The resulting SAM is firmly bound and not removed by sonication, as confirmed by manganese XPS (Mn 2p1/2) and by AFM. Electrochemistry confirms that Mn4O4(Ph2PO2)6 is anchored on the Au/IPPA surface and that redox chemistry can be mediated between the electrode and the surface-attached complex. Mn4O4(Ph2PO2)6 contains the reactive Mn4O46+ cubane core, a redox-active bioinspired catalyst.     

Highly sensitive detection of platelet-derived growth factor on a functionalized diamond surface using aptamer sandwich design

Aptamer-based fluorescence detection of platelet-derived growth factor (PDGF) on a functionalized diamond surface was demonstrated. In this work, a sandwich design based on the ability of PDGF to bind with aptamers at its two available binding sites was employed. It was found that this sandwich design approach significantly increases the fluorescence signal intensity, and thereby a very low detection limit of 4 pM was achieved. The effect of the ionic strength of MgCl(2) buffer solution was also investigated, and the most favourable binding for PDGF-BB occurred at a Mg(2+) concentration of 5.5 mM. Since the aptamers bind to the target PDGF with high affinity, fluorescence detection exhibited high selectivity towards different biomolecules. The high reproducibility of detection was confirmed by performing three cycles of measurements over a period of three days.     

Layer-by-layer PMIRRAS characterization of DMPC bilayers deposited on a Au111 electrode surface

A combination of Langmuir-Blodgett and Langmuir-Schaefer techniques was employed to deposit 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC) bilayers at a gold electrode surface. One leaflet consisted of hydrogen-substituted acyl chains, and the second leaflet was composed of molecules with deuterium-substituted acyl chains. This architecture allowed for layer-by-layer analysis of the structure of the bilayer. Photon polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS) was used to determine the conformation and orientation of the acyl chains of DMPC molecules in the individual leaflets as a function of the potential applied to the gold electrode. The bilayer is adsorbed onto the metal surface when the field applied to the membrane does not exceed approximately 108 V/m. When adsorbed, the bottom leaflet is in contact with a hydrophobic metal surface, and the top leaflet is interacting with the aqueous solution. The asymmetry of the environment has an effect on the orientation of the DMPC molecules in each leaflet. The tilt angle of the acyl chains of the DMPC molecules in the bottom leaflet that is in contact with the gold is approximately 10 degrees smaller than that observed for the top leaflet that is exposed to the solution. These studies provide direct evidence that the structure of a phospholipid bilayer deposited at an electrode surface is affected by interaction with the metal.     

Layer-by-layer adsorption of water molecules on the surface of a silver iodide crystal

Computer simulations at the molecular level were used to analyze the mechanism of the nucleation of water condensate from the vapor phase on the surface of a silver iodide crystal at 260 K. The initial stage of the condensation process is the sequential growth of monolayers on the substrate surface without formation of a compact microdroplet. The dependence of the equilibrium work of formation of the condensate film on its thickness exhibits oscillations. The formation of layers close to the substrate surface involves the overcoming of a Gibbs energy barrier.     

Anionic synthesis of chain-end functionalized polymers

The use of living, alkyllithium-initated anionic polymerization to prepare chain-end functionalization reactions is discussed. The scope and limitations of termination reactions with a variety of electrophilic species is illustrated for carbonation, hydroxyethylation, amination, and sulfonation. The methodology of using substituted 1,1-diphenylethylenes to provide a general, quantitative functionalization method is outlined and illustrated with examples of phenol end-functionalization and amination.     

Molecular flexibility as a factor affecting the surface ordering of organic adsorbates on metal substrates

The effect of molecular flexibility on the surface ordering of complex organic adsorbates is explored, using alpha,omega-dihexylquaterthiophene (DH4T) and mixed DH4T|tetracene phases on Ag(111) as model systems. The structure of DH4T/Ag(111) interfaces is determined by the flexibility of the hexyl chains at either end of the quaterthiophene backbone: Above 273 K, DH4T forms a nematic liquid crystalline phase with a director close to the [112] direction of the silver substrate. At 273 K, a reversible phase transition to a long-range ordered, point-on-line coincident phase is observed. However, this ordered state is still affected substantially by the flexible nature of DH4T, which materializes in a large number of local structural defects. If traces of DH4T are coevaporated with tetracene, inclusions of a 1:1 stoichiometric DH4T|tetracene phase are found in a tetracene/Ag(111) matrix (alpha-phase). In this mixed phase, the two surface enantiomers of pro-chiral DH4T on one hand and tetracene on the other form a complex stripe structure. The mixed phase shows a higher degree of order than present at the pure DH4T/Ag(111) interface, which also lacks chiral organization. The addition of tetracene molecules as structural templates stabilizes certain conformations of DH4T and thus, by balancing its structural flexibility, allows the surface-induced chirality of DH4T to become a decisive factor in determining the structure of the mixed phase.     

Synthesis and structure of metal complexes with organic polymers or inorganic supports

Macromolecular ligands have been widely used in the past two decades with the objective of preparing structurally defined heterogeneous catalysts from soluble organometallic complexes. This activity has been largely reconsidered and focused on few specific systems. In this connection the present paper reviews recent data concerning the preparation of macromolecular metal complexes derived from transition metals which can produce active catalytic complexes for olefin polymerization and oligomerization and comparison is made about the suitability of both organic resins (crosslinked polystyrene) and inorganic materials (silica, alumina and zeolites).