B位掺杂GdCo1-xSrxO3的制备及其光催化活性

用柠檬酸络合法制备了钙钛矿型GdCo1-XSrXO3(X=0.00, 0.02, 0.04, 0.06, 0.08)复合氧化物, 通过XRD, TEM 等手段对所生成纳米晶的物相结构、微观形貌、颗粒大小等进行了表征. 结果表明, 所合成的颗粒为钙钛矿型纳米晶, 球形. 通过其对活性艳红 X-3B 降解对其光催化活性进行了研究, 实验结果表明在B 位掺杂 Sr2+ 后使GdCoO3 的光催化活性明显提高, 当X=0.06 时, 即GdCo0.94Sr0.06O3 的光催化活性最佳.     

H2O2络合凝胶法制备纳米TiO2/SiO2复合催化剂及其光催化性能

采用H2O2络合凝胶法获得钛的络合物[TiO(H2O2)]2 水溶胶,并与SiO2水溶胶包覆复合,制备了纳米TiO2/SiO2复合半导体催化剂,其结构经XRD和BET表征。以含阳离子艳红染料模拟废水降解为模型反应,考察了复合催化剂的光催化性能。实验结果表明:经650℃焙烧后的复合催化剂中TiO2粒径为9.8 nm,光催化活性最好,SiO2的最佳掺杂量为25%。     

脉冲沉积制备Cu_2O/TiO_2纳米管异质结的可见光光催化性能

在用阳极氧化法制备有序排列TiO2纳米管阵列薄膜的基础上,引入脉冲沉积工艺,成功实现了均匀、弥散分布的Cu2O纳米颗粒修饰改性TiO2纳米管阵列,形成Cu2O/TiO2纳米管异质结复合材料.利用场发射扫描电镜(FESEM)、场发射透射电镜(FETEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外-可见漫反射光谱(UV-Vis DRS)对样品进行表征,重点研究了Cu2O/TiO2纳米管异质结的光电化学特性和对甲基橙(MO)的可见光催化降解性能.结果表明,Cu2O纳米颗粒均匀附着在TiO2纳米管阵列的管口和中部位置,所制备的Cu2O/TiO2纳米管异质结具有高效的可见光光催化性能;在浓度为0.01 mol?L-1的CuSO4溶液中制得的Cu2O/TiO2纳米管异质结表现出最好的电化学特性和光催化性能;另外,对Cu2O纳米颗粒影响光催化活性的机理进行了讨论.     

Cu2+掺杂的Bi2O3的制备及光催化性能的研究

本文采用并流沉淀法制备了Cu2+掺杂的纳米Bi2O3光催化剂(Cu/Bi原子比分别为1%,2%,3%和4%)。以甲基橙模拟有机污染物对催化剂的光催化性能进行了考察。用比表面(BET)、X-射线粉末衍射(XRD)、X-射线光电子能谱(XPS),紫外-可见漫反射光谱(DRS)和表面光电压谱(SPS)对所制备的催化剂进行了表征。结果表明,Cu2+掺杂量为3%时制备的Bi2O3具有最高的比表面积、孔容、最小孔径和晶粒尺寸。对甲基橙的光催化脱色结果显示掺杂量为3%时Cu2+-Bi2O3表现出最佳的光催化活性。     

水洗处理对Au/TiO2催化剂光催化活性的影响

以Au(S2O3)3-2为金前驱体, 分别采用水洗(W)和旋蒸(E)工艺制备了Au/TiO2催化剂. 用UV-Vis漫反射光谱(DRS)、X 射线衍射(XRD)、透射电子显微镜(TEM)和原子吸收光谱(AAS)对制备的催化剂样品进行了表征, 通过光催化降解甲基橙对催化剂光催化活性进行了评价. 结果表明, 通过水洗处理, 催化剂样品表面形成了具有较好分散性的金纳米粒子(2-5 nm), 而旋蒸工艺制备的样品表面形成一层金的包覆结构. Au/TiO2催化剂的光催化活性与制备工艺密切相关. 在相似的金负载量下, 水洗法制备的样品比旋蒸法制备的样品具有更高的光催化活性.     

层状纳米光催化复合材料H0.8Fe0.8Ti1.2O4/TiO2的合成及性质

用固相合成法制备出K0.8Fe0.8Ti1.2O4,并用离子交换反应制备出H0.8Fe0.8Ti1.2O4;通过C3H7NH2层间膨胀,TiO2粒子的插入和紫外光分解等反应,合成出一种新的层状光催化纳米复合材料-H0.8Fe0.8Ti1.2O4/TiO2.X射线衍射和漫反射等表征结果表明 该样品的层间高度为0.47nm,禁带能隙为2.18和2.88eV.用(>400 nm的光照射30 min,0.4 g样品可使甲基橙溶液(20 mg/L)的降解率达到22.1%.而同样条件下标准TiO2(P-25)仅为6.2%,表明所研制的层状纳米复合材料具有较高的光催化活性.     

层状、花形和棒状钛酸铋纳米结构的可控合成及光催化性能

通过可控水热法,制备出层状、花形和棒状钛酸铋(Bi4Ti3O12,BIT)纳米结构。通过X射线衍射(XRD)和场发射扫描电子显微镜(FESEM)观测其结构和形貌特征。XRD图显示,所制备的样品为层状钙钛矿结构。FESEM结果表明,通过控制水热过程的反应参数可以得到不同形貌的纳米粉体。紫外-可见漫反射光谱(UV-Vis DRS)表明BIT样品的带隙能约为2.63～2.95 eV。利用可见光(λ>420 nm)照射下的甲基橙降解实验评价了BIT样品的光催化性能。结果表明,BIT的光催化活性比掺氮TiO2(N-TiO2)高得多。所制备的层状BIT纳米结构光催化效率最高,经可见光照射360 min,甲基橙溶液的降解率可达95.0%。同时还研究了结构和形貌对不同条件下制备的BIT样品光催化活性的影响。     

核壳结构纳米Cu_2O/Ag的制备、表征和应用研究

通过溶胶-凝胶法制备了单分散性的球形纳米Cu_2O,采用取代反应法在上面负载一层纳米Ag,制备了核壳结构的Cu_2O/Ag纳米复合材料。利用透射电镜(TEM)分析了纳米Cu_2O/Ag的形貌,并用X射线衍射测(XRD)X射线光电子能谱(XPS)分析了其物相组成,利用紫外-可见光谱(UV-Vis)和光致发光光谱(PL)研究了其光谱特征,以罗丹明B(Rh B)为模型污染物,在紫外光照射下评价了纳米Cu_2O/Ag的光催化活性。结果表明:Cu_2O平均直径为150nm,表面纳米银直径为7nm,形成核壳结构;光催化结果显示,银沉积显著提高了Cu_2O的光催化活性。     

Cu_2O薄膜的可控制备及对次甲基蓝的光催化降解

采用电化学沉积法在掺锡氧化铟(ITO)导电玻璃上通过加入不同添加剂制备了不同形貌的Cu2O薄膜,利用XPS、XRD、SEM及UV-Vis对Cu2O薄膜的微观结构、表面形貌及光学特性进行了表征和分析,研究了不同形貌的Cu2O薄膜在H2O2-Cu2O薄膜体系中对次甲基蓝的降解。结果表明,所制得Cu2O薄膜为较纯的微米级Cu2O晶体,作为光催化剂,Cu2O薄膜3 h内对次甲基蓝的降解率均可达92.1%以上。无添加剂的Cu2O薄膜在前8次重复利用中降解率均可达92.4%以上,利用11次后仍具有较好的光催化活性,降解率可达82.4%。     

中空Ta_2O_5/TiO_2复合光催化剂的可控氧化制备及性能

以钛粉、钽粉为原料,炭黑作为反应性模板,通过熔盐法在炭黑表面原位生长了TaTiC_2纳米碳化物涂层,并以所得TaTiC_2/C复合物为碳化物前驱体,再经可控氧化制备出中空Ta_2O_5/TiO_2复合光催化剂。采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见(UV-Vis)漫反射(DRS)及N2物理吸附等手段对所制备的光催化剂进行形貌、显微结构及孔结构表征。以高压汞灯为紫外光源,以亚甲基蓝为目标降解物,通过光催化降解实验评价中空Ta_2O_5/TiO_2复合光催化剂的光催化活性。结果表明,熔盐法生长碳化物涂层厚度均匀(20~30 nm),碳化物主要以TaTiC_2晶相存在且具有纳米级的颗粒尺寸。中空Ta_2O_5/TiO_2复合光催化剂同时具有200 nm左右的中空大孔结构及壳层10 nm左右的介孔结构。中空大孔和介孔的存在提高了所制备催化剂对亚甲基蓝的吸附能力。此外,TiO_2与Ta2O5通过电子能带结构的耦合,有效提高了光生电子和空穴的分离效率,从而显著提高了光催化活性。nTi∶nTa=2.5∶1.5时,相应的中空Ta_2O_5/TiO_2复合光催化剂表现出最佳的光催化活性,对亚甲基蓝的紫外光催化降解率高达97%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.