铬-对苯二甲酸MOF的框架异构：MIL-88B(Cr)和MIL-101(Cr)

可以通过简单地控制乙酸浓度的方法,在相似的水热合成条件下合成2种同一家族的金属有机框架材料(MOFs):MIL-88B(Cr)和MIL-101(Cr)。在相对较低的乙酸浓度下,可以得到平均粒径为100 nm的MIL-101(Cr),并拥有很高的BET比表面积(3543 m^2·g^-1)。而在相对较高的乙酸浓度下,则可得到另一种具有“呼吸”特性结构的MOF——MIL-88B(Cr)。利用粉末X射线衍射、扫描电镜、N2吸附-脱附分析、热重分析等对它们的结构、形貌、孔隙率等性质做了详细的分析。     

五乙烯六胺改性金属有机骨架材料MIL-101(Cr)对CO_2的吸附性能

采用溶剂热法合成金属有机骨架材料MIL-101(Cr),用回流法将五乙烯六胺(PEHA)负载到MIL-101(Cr)孔道中的不饱和金属位点上,使用扫描电镜、粉末X射线衍射、氮气物理吸附、元素分析和傅里叶变换红外光谱等表征手段考察材料的结构和形貌,测试氨基改性前后的MIL-101(Cr)在25℃、不同压力下对CO_2的吸附效果。结果表明,负载0.24 m L五乙烯六胺后的MIL-101(Cr)对CO_2的吸附效果最好,在25℃、常压下对CO_2的饱和吸附量可达58.944 mg/g,相比未负载五乙烯六胺的MIL-101(Cr)吸附量(CO_2饱和吸附量为44.208 mg/g)增加了33%。随着吸附压力的增加,MIL-101(Cr)和0.24PEHAM IL-101(Cr)对CO_2的饱和吸附量逐渐增加,当吸附压力为1.1 MPa时,两者的吸附量分别为1 147.59和1 256.74 mg/g,表明该类材料在高压下对CO_2有着良好的吸附效果。     

Ag-Y/MIL-101吸附剂的制备及其吸附脱硫性能

通过银、钇双金属改性制备了Ag-Y/MIL-101吸附剂,并对Ag-Y/MIL-101进行了X射线衍射(XRD)、电镜(SEMEDS)、比表面积(BET)和热重(TG-DTG)表征。考察了Ag-Y/M IL-101金属负载顺序、金属负载浓度、金属溶液用量、负载时间对脱硫性能的影响,优化了吸附脱硫条件。结果表明,金属改性得到的Ag-Y/MIL-101保持了MIL-101的晶格结构。与M IL-101相比,Ag-Y/MIL-101的比表面积和孔容均有所下降。适宜Ag-Y/MIL-101的制备条件为:先负载银后负载钇,银离子和钇离子的负载浓度均为30 mmol/L,金属溶液用量均为1 mL,负载时间为8 h。适宜Ag-Y/MIL-101的吸附脱硫条件为:吸附剂用量0.05 g,模拟油为10 mL,吸附温度为60℃,吸附时间为8 h。在此条件下,Ag-Y/MIL-101对噻吩的吸附量达到21.7 mg/g。Ag能显著提高MIL-101的吸附硫容,Y能显著提高MIL-101的吸附选择性,因此,Ag-Y/MIL-101吸附剂中Ag和Y的协同作用使其拥有比MIL-101更高的硫容和噻吩脱硫选择性。     

MIL-101(Cr)材料的合成及对水中布洛芬的吸附研究

制备了MIL-101(Cr)材料,借助X-射线衍射和红外光谱技术确认了标题化合物的结构,利用扫描电子镜(SEM)技术及物理吸附技术表征了其形貌特征与孔结构特征。结果表明MIL-101(Cr)材料大小均匀,平均粒径为0.8μm, BET比表面积与总孔容积分别为1505 m²·g^-1和0.11 cm³·g^-1。随后进行了对布洛芬的吸附研究,结果表明MIL-101(Cr)对布洛芬的吸附在30 min即可达到平衡,且为拟一级动力学过程,符合Langmuir吸附模型,最大吸附量为136.3 mg·g^-1。10 mg MIL-101(Cr)吸附剂可实现20 mg·L^-1布洛芬溶液中溶质的98%去除率。以上实验结果可为探究MIL-101(Cr)在水中有机污染物的去除提供参考。     

MIL-101(Cr)填充针头式过滤器固相微萃取/高效液相色谱法检测水中雌激素

建立了多孔金属有机骨架MIL-101(Cr)填充针头式尼龙过滤器固相微萃取结合高效液相色谱-荧光检测器对水中雌二醇(E2)、雌三醇(E3)、雌酮(E1)3种雌激素进行快速检测的方法.MIL-101(Cr)与尼龙滤膜对雌激素表现出协同吸附效果.通过对萃取材料以及新型萃取装置制备过程、吸附、洗脱过程进行优化,可对10 mL...     

金属有机框架MIL-101(Fe)对水中微囊藻毒素-LR的吸附

通过溶剂热法制备了性质稳定的金属有机框架材料MIL-101(Fe),并用于吸附去除水中的微囊藻毒素-LR。采用电子显微镜、傅立叶变换红外光谱(FT-IR)、Zeta电位和N_2吸附-脱附等方法对制备的纳米材料进行了表征。MIL-101(Fe)具有多孔结构和较高的比表面积(375.2 m~2/g),尺寸约为500 nm。考察了pH值、离子强度、温度、吸附时间、浓度等参数对吸附剂吸附能力的影响。结果表明,静电作用和配位作用是主要的作用机理。MIL-101(Fe)对微囊藻毒素-LR的吸附速度很快(20 min内达到吸附平衡),吸附过程符合准二级动力学模型;MIL-101(Fe)对微囊藻毒素-LR表现出良好的吸附性能,其最大吸附量为256.4 mg/g。溶液中存在的腐植酸对MIL-101(Fe)的吸附性能产生一定的影响。受腐殖酸、盐类的影响,相同条件下MIL-101(Fe)对江水中微囊藻毒素-LR的吸附性能有所下降,但仍可达到68.1 mg/g。因此,该方法简便、高效,适用于快速除去污染水体中的微囊藻毒素-LR。     

Pt/MIL-101(Cr)在肉桂醛选择性加氢反应中的催化性能

采用简单易行的浸渍法将Pt纳米粒子负载到MIL-101(Cr)上, 制备了Pt/MIL-101(Cr)催化剂, 并对其在肉桂醛选择性加氢反应的催化性能进行了研究。XRD、N₂吸附、TEM和催化性能的研究结果表明, Pt的负载量对负载于MIL-101(Cr)上Pt纳米粒子的尺寸及所制备催化剂对肉桂醇的选择性有很大影响。低Pt负载量(1.0wt%)的Pt/MIL-101(Cr)较其他MOFs和无机材料在肉桂醛选择性加氢反应中表现出了高的催化性能, 在优化的反应条件下肉桂醛转化率和对肉桂醇的选择性可分别达96.5%和86.2%。Pt/MIL-101(Cr)催化剂具有良好的稳定性。Pt/MIL-101(Cr)所表现出的优良的催化性能同MIL-101(Cr)载体的孔道结构及其表面性质密切相关。     

Pt/MIL-101(Cr)在肉桂醛选择性加氢反应中的催化性能

采用简单易行的浸渍法将Pt纳米粒子负载到MIL-101(Cr)上,制备了Pt/MIL-101(Cr)催化剂,并对其在肉桂醛选择性加氢反应的催化性能进行了研究。XRD、N₂吸附、TEM和催化性能的研究结果表明,Pt的负载量对负载于MIL-101(Cr)上Pt纳米粒子的尺寸及所制备催化剂对肉桂醇的选择性有很大影响。低Pt负载量(1.0%)的Pt/MIL-101(Cr)较其他MOFs和无机材料在肉桂醛选择性加氢反应中表现出了高的催化性能,在优化的反应条件下肉桂醛转化率和对肉桂醇的选择性可分别达96.5%和86.2%。Pt/MIL-101(Cr)催化剂具有良好的稳定性。Pt/MIL-101(Cr)所表现出的优良的催化性能同MIL-101(Cr)载体的孔道结构及其表面性质密切相关。     

MIL-101(Fe)高效催化 β-蒎烯与甲醛的Prins缩合制备诺卜醇

通过水热晶化法制备了MIL-101(Fe)金属有机骨架材料, 利用X射线衍射(XRD)、 傅里叶变换红外光谱(FTIR)、 热重分析(TG)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)和X射线光电子能谱(XPS)对催化剂的结构和形貌进行了表征. 结果表明, 该材料用于催化β-蒎烯与甲醛的Prins缩合制备诺卜醇反应的效果优异; 催化剂合成温度、 合成时间、 催化剂用量、 反应溶剂、 反应温度和反应时间对β-蒎烯的反应结果均有一定影响. 在相似的反应条件下, 合成的MIL-101(Fe)催化β-蒎烯制备诺卜醇反应的最佳条件为使用150 ℃下反应15 h合成的催化剂MIL-101(Fe), 在90 ℃下反应8 h得到的β-蒎烯转化率高达97.3%, 诺卜醇选择性达到96.7%.     

MIL-101(Cr) Microporous Nanocrystals Intercalating Graphene Oxide Membrane for Efficient Hydrogen Purification

Graphene oxide (GO) is a promising two-dimensional building block for fabricating high-performance gas separation membranes. Whereas the tortuous transport pathway may increase the transport distance and lead to a low gas permeation rate, introducing spacers into GO laminates is an effective strategy to enlarge the interlayer channel for enhanced gas permeance. Herein, we propose to intercalate CO₂-philic MIL-101(Cr) metal-organic framework nanocrystals into the GO laminates to construct a 2D/3D hybrid structure for gas separation. The interlayer channels were partially opened up to accelerate gas permeation. Meanwhile, the intrinsic pores of MIL-101 provided additional transport pathways, and the affinity of MIL-101 to CO₂ molecules resulted in higher H₂/CO₂ diffusion selectivity, leading to a simultaneous enhancement in gas permeance and separation selectivity. The MIL-101(Cr)/GO membrane with optimal structures exhibited outstanding and stable mixed-gas separation performance with H₂ permeance of 67.5 GPU and H₂/CO₂ selectivity of 30.3 during the 120-h continuous test, demonstrating its potential in H₂ purification application.     

Assembling Ultrafine SnO2 Nanoparticles on MIL-101(Cr) Octahedrons for Efficient Fuel Photocatalytic Denitrification

Effectively reducing the concentration of nitrogen-containing compounds (NCCs) remains a significant but challenging task in environmental restoration. In this work, a novel step-scheme (S-scheme) SnO₂@MCr heterojunction was successfully fabricated via a facile hydrothermal method. At this heterojunction, MIL-101(Cr) octahedrons are decorated with highly dispersed SnO₂ quantum dots (QDs, approximate size 3 nm). The QDs are evenly wrapped around the MIL-101(Cr), forming an intriguing zero-dimensional/three-dimensional (0D/3D) S-scheme heterostructure. Under simulated sunlight irradiation (280 nm < λ < 980 nm), SnO₂@MCr demonstrated superior photoactivity toward the denitrification of pyridine, a typical NCC. The adsorption capacity and adsorption site of SnO2@MCr were also investigated. Tests using 20%SnO₂@MCr exhibited much higher activity than that of pure SnO₂ and MIL-101(Cr); the reduction ratio of Cr(VI) is rapidly increased to 95% after sunlight irradiation for 4 h. The improvement in the photocatalytic activity is attributed to (i) the high dispersion of SnO₂ QDs, (ii) the binding of the rich adsorption sites with pyridine molecules, and (iii) the formation of the S-scheme heterojunction between SnO₂ and MIL-101(Cr). Finally, the photocatalytic mechanism of pyridine was elucidated, and the possible intermediate products and degradation pathways were discussed.     

Adsorption of antimony using amino-functionalized magnetic MIL-101(Cr): Optimization by response surface methodology

Amino-functionalized magnetic MIL-101(Cr) was prepared via a one-step solvothermal method, characterized, and applied in adsorptive Sb(III) removal. The effects of solution pH, adsorbent dosage, and coexisting substances on the adsorption of Sb(III) by MIL-101(Cr)–NH₂/MnFe₂O₄ were studied. The adsorption kinetics were analyzed using pseudo-first order, pseudo-second order, intraparticle diffusion, and Elovich models, while Freundlich and Langmuir isotherm models were used to fit the experimental data. The pseudo-second-order kinetic model provided the best fit for the kinetic data. The maximum adsorption capacity of MIL-101(Cr)–NH₂/MnFe₂O₄ for Sb(III) was 91.07 ​mg/g, as calculated using the Langmuir adsorption isotherm model. Thermodynamic analysis revealed that the adsorption of antimony onto MIL-101(Cr)–NH₂/MnFe₂O₄ is spontaneous and endothermic, while response surface optimization revealed that the optimal conditions for Sb(III) adsorption by MIL-101(Cr)–NH₂/MnFe₂O₄ are an adsorbent loading of 222.55 ​mg/L, a pH of 4.5, and a temperature of 294.59 ​K. The predicted adsorption capacity of MIL-101(Cr)–NH₂/MnFe₂O₄ for Sb(III) is only a 1.8% deviation from the actual value. Furthermore, MIL-101(Cr)–NH₂/MnFe₂O₄ exhibits strong magnetism, allowing it to be separated from wastewater using a magnet. Finally, a preliminary economic analysis showed that the cost of treating a ton wastewater containing 25 ​mg/L antimony using this composite would be 26.24 USD. Thus, MIL-101(Cr)–NH₂/MnFe₂O₄ is promising for treatment of Sb(III)-containing wastewater.     

Tandem oxidative isocyanide-based cycloaddition reactions in the presence of MIL-101(Cr) as a reusable solid catalyst

The tandem oxidative three-component synthesis of two types of the heterocycles such as furans and imidazopyridines, via isocyanides [1+4] cycloaddition reactions in the presence of MIL-101(Cr) under aerobic conditions are reported. When the 4-toluenesulfonylmethyl isocyanide was used, an unexpected [3+2] cycloaddition reaction of isocyanides with aldehydes accomplished and dihydrophenyloxazoles and phenyloxazoles produced. These syntheses were successfully carried out using a wide scope of the substrates.