Comparison of the Separation Characteristics of the Organic–Inorganic Hybrid Octadecyl Stationary Phases XTerra MS C18 and XBridge C18 and Shield RP18 in RPLC

Differences in the system constants of the solvation parameter model, discontinuities in retention factor plots (log k against volume fraction of organic solvent) and retention factor correlation plots are used to study the retention mechanism on XTerra MS C₁₈, XBridge C₁₈ and XBridge Shield RP₁₈ stationary phases with acetonitrile–water and methanol–water mobile phases containing from 10 to 70% (v/v) organic solvent. Wetting of XBridge C₁₈ at 10 and 20% (v/v) acetonitrile is incomplete and is responsible for small changes in the retention mechanism. The intermolecular interactions responsible for retention on XTerra MS C₁₈ and XBridge C₁₈ are similar with minor differences in cavity formation and hydrogen-bonding interactions responsible for small selectivity differences. On the other hand, for bulky solutes there are large changes in retention at low volume fractions of organic solvent (<40% v/v) associated with steric repulsion on the XTerra MS C₁₈ stationary phases that is absent for XBridge C₁₈. Selectivity differences are more apparent for XBridge C₁₈ and XBridge Shield RP₁₈. For acetonitrile-water mobile phases cavity formation in the solvated XBridge Shield RP₁₈ is slightly more difficult and hydrogen-bond acid and base interactions are more important than for XBridge C₁₈. With methanol–water mobile phases it becomes slightly easier to form a cavity in the solvated XBridge RP₁₈ compared with XBridge C₁₈. In addition, the methanol-water solvated XBridge RP₁₈ is a stronger hydrogen-bond base and more dipolar/polarizable than XBridge C₁₈. These variations in selectivity justify the use of XBridge C₁₈ and XBridge Shield RP₁₈ as complementary stationary phases for method development.     

Ion-pair chromatography with UV absorbing counterions on reversed-phase layers. Part 1: Chromatography with hydroxynaphthalenesulfonic acids

The results of ion-pair chromatography with UV-absorbing counterions are described. Hydroxynaphthalenesulfonic acids are used as ion pair formers, and alkaloids as test samples. The separations are performed on silanized silica gel from Merck and KC₁₈F plates from Whatman. The influence of the counterion on the R_f-value is demonstrated. Some alkaloids exhibit characteristic fluorescence as ion pairs.     

Isocratic separation of erythromycin, related substances and degradation products by liquid chromatography on XTerra RP18

Summary A simple, sensitive, selective and robust isocratic LC method is described for the analysis of erythromycin on XTerra RP₁₈. The main component, erythromycin A, is separated from all known related substances and degradation products. Several unknown impurities are also separated. Acetonitrile-0.2 MK₂HPO₄pH7.0-water, (35∶5∶60, v/v) was used as a mobile phase at 1.0 mL min⁻¹. UV detection was at 215 nm. The robustness of the method was evaluated by a full-factorial experimental design.     

Determination of Fluorescent Whitening Agents in Infant Clothes and Paper Materials by Ion‐Pair Chromatography and Fluorescence Detection

A simple and rapid method was developed to simultaneously determine four stilbene‐type disulfonate and one distyrylbiphenyl‐type fluorescent whitening agents (FWAs) in infant clothes and paper materials by ion‐pair chromatography. FWAs were extracted from cloth and papers samples using a hot‐water extraction. The aqueous extract was then mixed with ion‐pair reagent, extracted with C₁₈‐SPE cartridges and eluted with methanol. The contents of FWAs were determined by an isocratic ion‐pair chromatography with RP‐C₁₈ column and equipped with fluorescence detection. Limits of quantitation were 0.04 to 0.45 ng/g in 10 g of samples. Recovery of FWAs in spiked infant cloth and paper samples was between 76 to 92% and precision (RSD) ranging from 2.0 to 4.0%. Analysis of three infant clothes and six paper materials found concentrations of selected FWAs ranging between n.d. to 24 μg/g and n.d. to 3.8 μg/g, respectively.     

Comparison of the Separation Characteristics of the Organic–Inorganic Hybrid Stationary Phases XBridge C8 and Phenyl and XTerra Phenyl in RP-LC

Differences in the system constants of the solvation parameter model and retention factor correlation plots for varied solutes are used to study the retention mechanism on XBridge C₈, XBridge Phenyl and XTerra Phenyl stationary phases with acetonitrile–water and methanol–water mobile phases containing from 10 to 70% (v/v) organic solvent. These stationary phases are compared with XBridge C₁₈ and XBridge Shield RP₁₈ characterized in an earlier report using the same protocol. The XBridge stationary phases are all quite similar in their retention properties with larger difference in absolute retention explained by differences in cohesion and the phase ratio, mainly, and smaller changes in relative retention (selectivity) by the differences in individual system constants and their variation with mobile phase type and composition. None of the XBridge stationary phases are selectivity equivalent but XBridge C₁₈ and XBridge Shield RP₁₈ have similar separation properties, likewise so do XBridge C₈ and XBridge Phenyl, while the differences between the two groups of two stationary phases is greater than the difference within either group. The limited range of changes in selectivity is demonstrated by the high coefficient of determination (>0.98) for plots of the retention factors for varied compounds on the different XBridge phases with the same mobile phase composition.     

Determination of Cyanuric Acid in Milk Powder and Swimming Pool Water by Ion‐pair Reversed‐phase Liquid Chromatography

An ion‐pair reversed‐phase high‐performance liquid chromatographic method, using tetrabutylammonium bromide (TBAB) as ion‐pair reagent, has been developed for the analysis of cyanuric acid (CA) in milk powder and swimming pool water. It was found that the effect of the concentrations of ion‐pair reagent on the retention of cyanuric acid was different for standard solution and different real samples. The separation was carried out on a reversed‐phase C₁₈ column with 85:15 (V/V) water‐acetonitrile (ACN) containing different concentration of TBAB as mobile phase for different samples. The linear range of the calibration curve for CA was 0.1–100 mg·L^?1. The detection limits calculated at S/N=3 was 0.11 mg·L^?1 for the analysis of milk powder and 0.31 mg·L^?1 for the analysis of swimming pool water, respectively. The method was successfully applied to the analysis of CA in milk powder and swimming pool water.     

Reversed phase planar chromatography of dansyl DL amino acids with bovine serum albumin in the mobile phase

Summary The chromatographic behavior of twelve dansyl DL amino acids, one D isomer and eleven L isomers on RP₁₈W/UV₂₅₄, RP₁₈W/F_254s, and Sil C₁₈–50 UV₂₅₄ plates developed with aqueous—organic solutions containing bovine serum albumin (BSA) as chiral complexing agent has been extensively investigated. Enantiomeric resolution is highly dependent on mobile phase pH and ionic strength, and on the concentration of both BSA and organic modifier. All the racemates have been resolved within a development time of 1 h 30 min. The selectivity factors () for the dansyl amino acids have been compared with those from planar chromatography for the corresponding DNP, DNPy, and Fmoc amino acids, and with those of the same dansyl derivatives on a column prepared from BSA bound to silica gel.     

Automated high-performance liquid chromatographic determination of amphetamine in biological fluids using column-switching and on-column derivatization

Summary A rapid and simple liquid-chromatographic method has been developed for on-line quantification of amphetamine in biological fluids. Untreated samples (20 μL) are injected directly into the chromatographic system and purified on a 20 mm×2.1 mm i.d. pre-column packed with 30 μm Hypersil C₁₈ stationary phase. After clean-up the analyte is transferred to the analytical column (125 mm×4 mm i.d., 5 μm LiChrospher 100 RP₁₈) for derivatization and separation using a mixture of acetonitrile and the derivatization reagent (o-phthaldialdehyde andN-acetyl-L-cysteine) as the mobile phase. The experimental conditions for on-line derivatization and resolution of the amphetamine have been optimized, and the results have been compared with those obtained by derivatizing the analyte in pre-column mode. The method described has been applied to the determination of amphetamine in plasma and urine. Good linearity and reproducibility were obtained in the 0.1–10.0 μg mL⁻¹ concentration range, and limits of detection were 25 ng mL⁻¹ and 10 ng mL⁻¹ with UV and fluorescence detection, respectively. The procedure described is very simple and rapid, because no off-line manipulation of the sample is required; the total analysis time is approximately 8 min.     

Simultaneous Determination of Tin,Nickel, Lead,Cadmium and Mercury in Tobacco and Tobacco Additives by Microwave Digestion and RP‐HPLC Followed by On‐Line Column Enrichment

A new method for the simultaneous determination of five heavy metal ions, tin, nickel, lead, cadmium and mercury ions as metal‐tetra‐(2‐aminophenyl)‐porphyrin (T₂APP) chelates was developed using reversed‐phase high performance liquid chromatography (RP‐HPLC) equipped with a photodiode array detector and combined with an on‐line enrichment technique. The tin, nickel, lead, cadmium and mercury ions were pre‐column derivatized with T₂APP to form color chelates. The Sn‐T₂APP, Ni‐T₂APP, Hg‐T₂APP, Cd‐T₂‐APP and Pb‐T₂APP chelates can be absorbed onto the front of the enrichment column when they are injected into the injector and sent to the enrichment column [Waters Xterra? RP₁₈(5μ, 3.9 × 20 mm)] with a buffer solution of 0.05 mol/L pyrrolidine‐acetic acid (pH = 10.0) as mobile phase. After the enrichment had finished, by switching the six‐port switching valves, the retained chelates were back‐flushed by mobile phase and traveling towards the analytical column. These chelates separation on the analytical column [Waters Xterra? RP₁₈ (5μ, 3.9 × 150 mm)] was satisfactory by gradient elution with methanol (containing 0.05 mol/L pyrrolidine‐acetic acid buffer salt, pH = 10.0) and acetone (containing 0.05 mol/L pyrrolidine‐acetic acid buffer salt, pH = 10.0) as mobile phase. The linearity range is 0.01?120 μg/L for each metal ion. The detection limits (S/N = 3) of tin, nickel, lead, cadmium and mercury are 4.0 ng/L, 3.5 ng/L, 2.5 ng/L, 3.0 ng/L and 3.0 ng/L, respectively. This method was applied to the determination of tin, nickel, lead, cadmium and mercury ions in tobacco and tobacco additives with good results.     

The Phenylphosphinidene C6H5P is Stable Under Unimolecular Conditions - A Theoretical Prediction

Abstract

As members of the family of low-coordinated phosphorus compounds, the phosphinidenes (RP) containing subvalent phosphorus (σ¹,λ¹-P) are of current interest. Until now, no Organophosphiaidene RP (R=Alkyl, Aryl) is known to be stable in the condensed phase. As the results of trapping experiments are questioned, the formation of RP as intermediates is still doubtful [1]. The mass spectrometric decay of some organophosphorus compounds yields radical cations [C₆,H₅,P]^+? m/z 108. For these species structures 1 and 2 are conceivable:     

Solid‐phase extraction and residue determination of glyphosate in apple by ion‐pairing reverse‐phase liquid chromatography with pre‐column derivatization

A new method for glyphosate residue determination in apple has been developed. A SPE cartridge was used to clean up the samples before derivatization. Glyphosate was derivatized with 4‐chloro‐3,5‐dinitrobenzotrifluoride (CNBF) and quantified by reverse ion‐pair liquid chromatography using cetyltrimethylammonium bromide (CTAB) as ion‐pair reagent. In pH 9.5 H₃BO₃–Na₂B₄O₇ medium, the reaction of glyphosate with CNBF was complete after 30 min at 60°C. The stability of the derivative on exposure to light at room temperature in methanol–water was demonstrated. The labeled glyphosate was separated on a Kromasil C₁₈ column (250×4.6 mm, 5 μm) at room temperature and UV detection was applied at 360 nm. Separation was achieved within 15 min in gradient elution mode. The correlation coefficient for the method was 0.9998 at concentrations ranging from 0.1 to 50 μg/g. The calculated recoveries for glyphosate in apple were from 86.00 to 99.55%, and the relative standard deviations (n = 6) were from 1.43 to 6.32. The limit of detection was 0.01 μg/g for glyphosate in apple.     

Simultaneous Determination of Mixtures of Nitrite and Nitrate by Reversed‐Phase Ion‐Pair Liquid Chromatography

To overcome the relatively low resolution in the separation and quantitative analysis of mixtures of nitrite and nitrate, a reversed‐phase ion‐pair liquid chromatographic method is developed with advantages of high accuracy, good selectivity, high efficiency, and low cost. By employing cetyltrimethylammonium bromide (CTAB) as the ion‐pair reagent, this method can work excellently in situations where one component in the mixture is highly in excess (e.g., molar ratio of n( NO₂⁻):n(NO₃⁻) ranging from 1:99 to 95:5). The operation parameters were optimized on a Shim‐pack VP‐ODS(150 L × 4.6) analytical column using a methanol/water ratio of 50:50 (v/v) mobile phase containing 7.0 mmol/L CTAB and 3.1 mmol/L potassium dihydrogen phosphate (KH₂PO₄).The column works at a temperature of 35 °C with a flow rate of 1.5 mL/min. Such a protocol can be applied to monitor the formation of trace nitrous acid during the oxidative decomposition of nitric acid.     

Selective and sensitive analysis of 1-nitropyrene in diesel exhaust particulate extract by multidimensional HPLC

Summary A multicolumn (MC) HPLC method for the determination of 1-nitropyrene (1-NP) at trace-levels via on-line reduction to 1-aminopyrene and fluorescence detection is presented. On the first column, packed with a pyrenebutyric acid amide stationary phase, the nitro-derivatives of PAHs are strongly retained and separated from other matrix components. The nitro-PAHs-containing fractions are transferred onto a RP₁₈-column via stepwise gradient elution and finally separated according to their various lipophilicities and sizes. To increase the overall selectivity and sensitivity of the multidimensional method (MD-HPLC system) post-column, on-line reduction of the nitro-PAHs to the respective amino-PAHs via a short catalysis column is performed thus enhancing the sensitivity significantly (to low pg levels). The applicability of this method for the determination of trace amounts of 1-NP in real samples (diesel particulate extracts) is demonstrated.     

Liquid chromatographic determination of aliphatic amines in water using solid support assisted derivatization with 9-fluorenylmethyl chloroformate

Summary A simple and sensitive method has been developed for the liquid chromatographic determination of short-chain aliphatic amines in water. Analytes are retained in solid-phase extraction (SPE) cartridges, and then derivatized by drawing an aliquot of the fluorogeneic reagent 9-fluorenylmethyl chloroformate (FMOC) through the cartridges. After a certain reaction time the derivatives formed are desorbed with acetonitrile. The collected extracts are then chromatographed on a LiChrospher 100 RP₁₈ 125 mm×4 mm i.d., 5 μm, column using an acetonitrile-water gradient. The influence of experimental conditions (SPE material, volume of sample, concentration of FMOC, time of reaction and pH) has been investigated. Optimal results have been obtained with C₁₈ SPE cartridges using a sample volume of 5.0 mL. For derivatization, 0.25 mL aliquots of 25 mM FMOC have been used, the reaction time being only 2 min. The method has been applied to the quantification of several aliphatic amines: methylamine, ethylamine, dimethylamine,n-butylamine,n-pentylamine andn-hexylamine. Under the proposed conditions the percentages of analytes retained plus derivatized were of about 54–107% compared to those obtained with direct solution derivatization. The method provided good reproducibility, linearity and accuracy within the 0.050–1.0 mg L⁻¹ concentration range. The limits of detection were in the 0.25–5.0 μg L⁻¹ range. The utility of the described approach has been tested by analysing tap water, river water and industrial waste water.     

Ion pairing in H<Subscript>2</Subscript>O and D<Subscript>2</Subscript>O solutions of lead nitrate,as determined with <Superscript>207</Superscript>Pb NMR spectroscopy

The temperature and concentration dependences of ²⁰⁷Pb NMR chemical shifts of Pb(NO₃)₂ in D₂O are reported. The results are analyzed in terms of exchange between a solvated lead ion and the Pb(NO₃)⁺ contact-ion pair. Predictions of the chemical shift difference between the aquated ion and contact-ion pair are carried out for the gas-phase entities and for the solvated species with a DFT calculation. Previously reported data on ²⁰⁷Pb NMR chemical shifts of Pb(NO₃)₂ in H₂O are reevaluated. From the analysis, the enthalpy of dissociation of the contact-ion pair is found to be–42.3±1.0 kJ/mol.     

Determination of synephrine in feeds by a novel quick,easy, cheap,effective, rugged,and safe solid‐phase extraction method combined with UHPLC–MS/MS

To detect and quantify synephrine in feed, an effective analytical method based on quick, easy, cheap, effective, rugged, and safe solid‐phase extraction coupled to ultra high performance liquid chromatography with tandem mass spectrometry was developed with isotopic internal standards. Pretreatment was performed using quick, easy, cheap, effective, rugged, and safe solid‐phase extraction with primary secondary amine and C18 sorbent as sorbents in combination with Oasis MCX column clean‐up to extract and purify feed samples. Tandem mass spectrometry detection in positive ion mode was conducted in positive multiple reaction monitoring mode in addition to the quantitative internal standard method. Two transitions of synephrine at m/z 168.1/150.0 and 168.1/135.0 were selected, and m/z 168.1/135.0 was determined as the quantification ion pair. D₉‐Terbutaline was selected as an internal standard, for which m/z 235.1/153.0 was selected as the quantification ion pair. Good linearity was shown for synephrine in the range of 0.5–50 μg/L, and the correlation coefficient exceeded 0.999. The recoveries in three different feed samples at three spiked levels were 81.42–112.08%, and the relative standard deviations were not greater than 14.66%. The method proposed in this study was reliable and highly effective, and its sensitivity, accuracy, and precision are suitable for determining synephrine residues in feed samples.     

A DFT Quantum‐Chemical Study of Ion‐Pair Formation for the Catalyst Cp2ZrMe2 /MAO

A process of ion‐pair formation in the system Cp₂ZrMe₂/methylaluminoxane (MAO) has been studied by means of density functional theory quantum‐chemical calculations for MAOs with different structures and reactive sites. An interaction of Cp₂ZrMe₂ with a MAO of the composition (AlMeO)₆ results in the formation of a stable molecular complex of the type Al₅Me₆O₅Al(Me)O–Zr(Me)Cp₂ with an equilibrium distance r(Zr–O) of 2.15 Å. The interaction of Cp₂ZrMe₂ with “true” MAO of the composition (Al₈Me₁₂O₆) proceeds with a tri‐coordinated aluminum atom in the active site (OAlMe₂) and yields the strongly polarized molecular complex or the μ‐Me‐bridged contact ion pair ( d ) [Cp₂(Me)Zr(μMe)Al≡MAO] with the distances r(Zr–μMe) = 2.38 Å and r(Al–μMe) = 2.28 Å. The following interaction of the μ‐Me contact ion pair ( d ) with AlMe₃ results in a formation of the trimethylaluminum (TMA)‐separated ion pair ( e ) [Cp₂Zr(μMe)₂AlMe₂]⁺–[MeMAO]^– with r[Zr–(MeMAO)] equal to 4.58 Å. The calculated composition and structure of ion pairs ( d ) and ( e ) are consistent with the ¹³C NMR data for the species detected in the Cp₂ZrMe₂/MAO system. An interaction of the TMA‐separated ion pair ( e ) with ethylene results in the substitution of AlMe₃ by C₂H₄ in a cationic part of the ion pair ( e ), and the following ethylene insertion into the Zr–Me bond. This reaction leads to formation of ion pair ( f ) of the composition [Cp₂ZrCH₂CH₂CH₃]⁺–[Me‐MAO]^– named as the propyl‐separated ion pair. Ion pair ( f ) exhibits distance r[Zr–(MeMAO)] = 3.88 Å and strong C_γ‐agostic interaction of the propyl group with the Zr atom. We suppose this propyl‐separated ion pair ( f ) to be an active center for olefin polymerization.     

A Transient Ion Pair (CCl · Cl−) in Irradiated Liquid CCl4: Evidence for a ‘delayed’ geminate ion neutralisation. (Preliminary communication)

Detailed cation scavenger studies in pulse-irradiated pure, liquid CCl₄ reveal that the 500 nm absorption has both, neutral and cationic characteristics, and that CCl₄⁺ must be the precursor. It is shown that all experimental results are compatible with the following ion neutralisation mechanism: CCl + Cl^? → (CCl · Cl^?) → CCl₄. The 500 nm band is assigned to the CCl₃⁺-cation (free or complexed). Its neutralisation therefore does not occur on ion recombination, but is delayed by the life time of the ion pair: τ_½ (ion pair) = 33 ± 3 ns at ?22°C with activation energy of 10.9 ± 2.1 kJ/mol. Possible reasons for the ion pair stability are briefly discussed.     

Retention of nucleic acids in ion‐pair reversed‐phase high‐performance liquid chromatography depends not only on base composition but also on base sequence

The study on nucleic acid retention in ion‐pair reversed‐phase high‐performance liquid chromatography mainly focuses on size‐dependence, however, other factors influencing retention behaviors have not been comprehensively clarified up to date. In this present work, the retention behaviors of oligonucleotides and double‐stranded DNAs were investigated on silica‐based C₁₈ stationary phase by ion‐pair reversed‐phase high‐performance liquid chromatography. It is found that the retention of oligonucleotides was influenced by base composition and base sequence as well as size, and oligonucleotides prone to self‐dimerization have weaker retention than those not prone to self‐dimerization but with the same base composition. However, homo‐oligonucleotides are suitable for the size‐dependent separation as a special case of oligonucleotides. For double‐stranded DNAs, the retention is also influenced by base composition and base sequence, as well as size. This may be attributed to the interaction of exposed bases in major or minor grooves with the hydrophobic alky chains of stationary phase. In addition, no specific influence of guanine and cytosine content was confirmed on retention of double‐stranded DNAs. Notably, the space effect resulted from the stereostructure of nucleic acids also influences the retention behavior in ion‐pair reversed‐phase high‐performance liquid chromatography.     

Theoretical investigation of ion pair SN2 reactions of alkali isothiocyanates with alkyl halides. Part 1. Reaction of lithium isothiocyanate and methyl fluoride with inversion mechanism

The gas‐phase ionic S_N2 reactions NCS^‐ + CH₃F and ion pair S_N2 reaction LiNCS + CH₃F with inversion mechanism were investigated at the level of MP2(full)/6‐311+G**//HF/6‐311+G**. Both of them involve the reactants complex, inversion transition state, and products complex. There are two possible reaction pathways in the ionic S_N2 reaction but four reaction pathways in the ion pair S_N2 reaction. Our results indicate that the introduction of lithium significantly lower the reaction barrier and make the ion pair displacement reaction more facile. For both ionic and ion pair reaction, methyl thiocyanate is predicted to be the major product, but the latter is more selective. More‐stable methyl isothiocyanate can be prepared by thermal rearrangement of methyl thiocyanate. The theoretical predictions are consistent with the known experimental results. © 2004 Wiley Periodicals, Inc. Int J Quantum Chem, 2005