Proposal for underwater structural analysis using the techniques of ESPI and digital holography

The purpose of this article is to study the application of the holographic interferometry techniques in the structural analysis of submarine environment. These techniques are widely used today, with applications in many areas. Nevertheless, its application in submarine environments presents some challenges. The application of two techniques, electronic speckle pattern interferometry (ESPI) and digital holography, comparison of advantages and disadvantages of each of them is presented. A brief study is done on the influence of water properties and the optical effects due to suspended particles as well as possible solutions to minimize these problems.     

High resolution digital holography

In digital Fresnel holography, present specifications of charge-coupled device cameras require the incident beams to be quasi-parallel. That implies large speckle grain size and low lateral resolution in reconstructed images. Better lateral resolutions are demonstrated in our work, down to 8 μm, allowing the observation of sub-millimetre objects by digital holography. The experimental set-up built samples the incident light distribution with a definition of 500 pixels mm⁻¹. The maximum acceptable angle is then widened and the hologram recording and reconstruction distances are drastically reduced, as well as the speckle size. Interferometric holography was implemented for the measurement of the deformation of a sub-millimetre silicon cantilever and results in phase-contrasts imaging are also reported. The design of dedicated complementary metal-oxide-semiconductor active pixel sensor cameras is also discussed.     

Examination of the upper measurement limit in displacement measurement using fringe compensation in digital holography

Digital holography is a widely used method for displacement measurement in coherent optical metrology. An obvious limit of the method is that too large displacements result in dense fringes, so the fringes are practically invisible. The maximum number of contour fringes in displacement measurement is limited, because the cameras are discrete devices and sampling theory plays an important role. Because of the limited measurement range, compensation methods are promising tools for practical measurements. It can be shown that the practical measurement range can be extended above the Nyquist sampling limit. Compensation methods can be digital, because digital holographic interferometry operates with images recorded with a digital camera. In our research work the upper measurement range of fringe compensation method was examined. Our goal was to perform automatic compensation even if the displacement is higher than the measurement range of the basic method. The operation of the automatic fringe compensation method was based on the combination of two types of out-of-plane displacement measurements with different sensitivities.     

同轴全息术用于粒子场测量的数值模拟

 采用数值方法模拟了同轴全息术测量粒子场的过程,对两种不同的数值算法＿直接傅里叶变换算法和卷积算法,进行了分析和比较,结果表明卷积算法符合实际要求。分析了记录图像的空间频谱及其对图像采样频率的要求,得出了在记录波长、采样间隔等条件一定的情况下的最小记录距离。对于一幅512×512像素的数字图像,若像元尺寸为6.7 μm,所用光波长为532 nm,则最小记录距离为43.2 mm。在此基础上对实验记录的振幅和相位型静态粒子的数字全息图,均得到了满意的数值再现像。     

Information reduction using lensless Fourier transform digital composite holography

An optical hologram contains substantially more information than necessary for some specific applications. Practical methodology of handling huge information contents in these holograms for such applications is cumbersome. In this paper, a method of information reduction, which aims at efficient storage and transmission of holograms, is investigated using digital composite holography in lensless Fourier transform configuration. The maximum information reduction factor obtained in our experiment is 105. The advantages/disadvantages of this method over an earlier method used in optical holography [Lin LH. A method of hologram information reduction by spatial frequency sampling. Appl Opt 1968;7:545] are also discussed.     

Measurement of static and vibrating microsystems using microscopicTV holography

This paper describes a microscopic TV holographic arrangement to study the static and vibrating microsystems. In the optical setup, the object beam and the reference beam arms are provided with a phase shifting mirror and a bias phase modulation mirror to carry out the measurement of the out-of-plane deformation and the vibration amplitude fields, respectively. A long working distance microscope is used in the setup for magnifying and imaging the objects on to the CCD camera. For static fringe analysis, the system is used in double exposure subtraction mode of operation, while for vibration fringe analysis, it is used in the time average contrast reversal refreshing mode of operation. An improved approach for qualitative analysis of time averaged fringes helps in reducing the number of frames required for analysis. The usefulness of the system is demonstrated by examples of static and vibration measurements for different microobjects.     

Wave front reconstruction of Fresnel off-axis holograms with compensation of aberrations by means of phase-shifting digital holography

Off-axis holograms recorded with a CCD camera are numerically reconstructed in amplitude by calculating through the Fresnel–Kirchhoff integral. A phase-shifting Mach–Zehnder interferometer is used for recording four-quadrature phase-shifted off-axis holograms. The basic principle of this technique and its experimental verification are described. We show that the application of this algorithm allows for the suppression of the zero order of diffraction and of the twin image and that the contrast of the reconstructed images can be further enhanced by digital compensation of the aberrations introduced by the holographic recording system     

Reduction of speckle noise in digital holography by using digital image processing

A fundamental problem in optical and digital holography is the presence of speckle noise in the reconstruction process. Many approaches have been carried out in order to overcome such a problem ranging from modifying the spatial coherence of the illumination (optical techniques) to image processing techniques (digital techniques). This work shows the merged use of digital image processing techniques in order to reduce the speckle noise in digital reconstruction of optically recorded Fresnel's holograms. The proposed filtering techniques are illustrated with experimental results.     

Curvature measurement of optical surface using digital holography

In this paper, an optical surface curvature measurement technique based on digital holography is proposed. Unlike the previous digital holographic methods, which only involve a small part of the measured data for parameter estimation, the proposed method adopts more of them using least square method. Hence, the analyzed result is not affected by data extraction direction and less sensitive to imperfect phase compensation. The proposed method is demonstrated with a sample of reflection mirror in laser resonator, and verified by comparing the measurement result with that of the white light interferometer.     

Contouring of diffused objects by using digital holography

A simple method for contouring of diffused objects by using lensless Fourier transform digital holography (LFTDH) and dual-index immersion method is presented. Depth contour interval up to minimum of 0.12 mm could be achieved without making the interference phase fringes over crowded.     

Towards full-resolution inline electron holography

With the availability of fast computers, inline electron holography, a technique for reconstructing both amplitude and phase of the electron wave function as scattered by the sample from a set of differently aberrated transmission electron microscopy images, is becoming increasingly quantitative. While focal series reconstruction from transmission electron microscopy images has already been practiced for at least 3 decades, existing approaches can only recover a relatively small band of spatial frequencies. Here I present a reconstruction scheme which is capable of reconstructing the electron wave function for a very large range of spatial frequencies, demonstrating its performance using simulated as well as experimental data.     

Improvement of signal-to-noise ratio in digital holography using wavelet transform

The basic problem in optical and digital holography is the presence of speckle noise in the reconstruction process, which reduces the signal-to-noise ratio (SNR). The presence of speckle noise is serious drawback in optical and digital holography since it substantially reduces the SNR in the reconstructed image. In this paper, we present wavelet filtering to improve SNR in the reconstructed images from digital holograms. Experimental results are presented.     

Method for eliminating zero-order diffraction in lensless Fourier transform digital holography

A method to induce phase shifting in lensless Fourier of digital holography system is presented. In this method, by computer simulation and theoretical analysis on the technology to eliminate the influence of zero-order diffraction in force, it can be found that, a reference light induced in a random non-2π integral number of phase shifting shooting to get the second hologram, and wave reconstruction can be got by the difference value image of the two holograms. And, the method of different digital holography record system with different phase shifting should be used. In this paper, theoretical analyses have been done in detail to discuss the problems that exist in the unsuitable phase-shifting methods. Furthermore, some experiments have been done to prove the reliability of this method. This method can significantly improve the image quality and give better resolution of the reconstructed image.     

Use of digital color holography for crack investigation in electronic components

This paper presents the experimental optical analysis of the crack inside an electronic component. The optical setup is used to carry out multidimensional deformation measurements using digital color holography and the spatial multiplexing of holograms. Since the Fresnel transform method depends on wavelength, a wavelength-dependent-zero-padding algorithm is described and results in a rigorous sizing of each reconstructed monochrome image. The criterion to optimize the parameters is presented and is based on minimizing the widening of the impulse response of the full recording/reconstruction process. The application of the proposed method is illustrated through the analysis of the mechanical deformation of the electronic component, and offers keys to understand its failure mode in industrial conditions.     

Green's formulation for robust phase unwrapping in digital holography

We present, for the first time to the best of our knowledge, a phase unwrapping method based on an algorithm which makes use of Green's first identity. This method aims at recovering the correct phase information encoded in a fringe pattern after digital holography (DH) numerical processing. DH provides a quantitative measurement of the three-dimensional surface profile of objects. The information about the profile can be obtained in principle from the phase-map. However, the measured phase-map provides the actual phase values wrapped mod.2π so that an unwrapping process is required in order to reconstruct the object profile.     

High-resolution digital transmission microscopy—a Fourier holography approach

A spherical reference field is used to construct a digital holographic system with a demonstrated resolution up to 228 line pairs per mm. The reference field originates from a GRIN lens placed 1 mm from the illuminated object. This allows the use of a standard sensor to record the hologram with the required numerical aperture. The image is determined by evaluation of the Rayleigh–Sommerfeld diffraction integral that relates the object field in the image plane to the object field in the sensor plane. Experimental results are given for two charge coupled device sensors and one complementary metal-oxide-semiconductor active pixel sensor.     

The determination of material parameters of microcomponents using digital holography

Progresses in microsystem technology promise a lot of new applications in industry and research. However, the increased complexity of the microsystems demand sensitive and robust measurement techniques. Fullfield and non invasive methods are desirable to get access to spatially resolved material properties and parameters.This contribution describes a simple and fast interferometric method for the analysis of shape and deformation of small objects by optical means. These quantities together with a well defined loading of the components can be the starting point for the determination of material parameters like Poisson-ratio, Young's modulus or the thermal expansion coefficient. Holographic interferometry and multiple wavelength contouring as well as multiple source point contouring are precise enough to fulfill the requests for precision and resolution in microsystem technology even on complex shaped structures with steps or gapsA new adaptive, iterative algorithm is developed and applied to the measured results that allows the numerical evaluation of the phase data to get absolute shape and deformation information in Cartesian coordinates. Surfaces with holes, gaps and steps can be registered without any ambiguities. Digital holography as the underlying holographic recording mechanism is extremely suitable for small objects and lead to simple and compact setups in which the objects’ shape as well as their deformation behavior can be recorded. Experiments using silicon microbeams and an object from fine mechanics are described to show the great potential of these fast and robust measurement techniques with respect to the determination of material parameters.     

Potential of digital holography in particle measurement

This paper describes the potential power of digital holography in particle measurement and its expected development in the near future. In digital holography, image reconstruction is carried out numerically on a computer using observed hologram patterns and some quantitative information can be derived from the reconstructed images. In this paper, the basic concept and procedure of digital in-line holography are shown mainly for particle depth measurement and the performance test results obtained in numerical simulations and experiments are demonstrated to examine the potential of the present method.     

Reconstruction of digital hologram of small particles on arbitrarily tilted plane using digital holography

Digital holographic off-axis geometry is presented for the reconstruction of the digital hologram of small particles in an arbitrarily tilted plane. A single hologram is sufficient to obtain a well focused clear image. We can't obtain clear images of small particles in the case of plane tilted to the detector plane by ordinary reconstruction method because of the rotation of the hologram plane. Rotational transformation based on coordinate rotation in Fourier space makes it possible to reconstruct holographic images on any plane in the object space. The reconstruction of digital hologram is based on the plane wave expansion of the diffracted wave fields, using Fourier optics and the two-axis rotation of the wave vectors. With this method, the object-to-hologram distance can be any small distance because the minimum distance requirement does not apply.     

Elimination of zero-order diffraction in digital off-axis holography

A simple experimental method of eliminating zero-order diffraction in the reconstructed image of off-axis digital holography is presented. Holographic diffraction grating acting as a beam splitter, an off-axis holography system is formed. The holograms of object with different recording parameters are obtained by adjusting the reflecting mirror in the recording optical system to vary the incidence orientation of the object beam in CCD to introduce a phase shift. The zero-order image can be eliminated by numerically processing the holograms of object with different recording parameters. The theoretical analyses have been done in detail and the experimental results are also given. The zero-order image eliminated, the area of reconstructed image increases remarkably, the image quality can then be significantly improved and the better resolution obtained. The experimental results show that the method presented in this paper is feasible, simple in optical system and easy in operation and data processing.