Assembly of multilayered films using well-defined, end-labeled poly(acrylic acid): influence of molecular weight on exponential growth in a synthetic weak polyelectrolyte system

We report on the influence of polyanion molecular weight on the growth and structure of multilayered thin films fabricated from poly(allylamine) (PAH) and well-defined, end-labeled poly(acrylic acid) (PAA) synthesized by atom transfer radical polymerization. We observed striking differences in the growth of PAH/PAA films fabricated using well-defined PAA compared to films fabricated using higher molecular weight, commercially available PAA. Past studies demonstrate that the thicknesses of PAH/PAA films increase as linear functions of the number of PAH and PAA layers deposited over a broad range of pH (e.g., from pH 2.5 to 4.5). We observed the thicknesses of films fabricated using solutions of PAH and PAA adjusted to pH 7.5 and 3.5, respectively, to increase in a nonlinear manner. Films fabricated using well-defined, low molecular weight samples of PAA under these conditions increased in thickness exponentially. Experiments using samples of PAA having substantially non-overlapping molecular weight distributions demonstrated a clear relationship between the molecular weight of PAA and rates of film growth. We also used confocal microscopy, in combination with fluorescently end-labeled samples of PAA, to characterize the location of PAA in these assemblies. The results of these experiments, when combined, support the general conclusion that PAA is able to penetrate or diffuse into these films over large distances during assembly. The mechanism of growth for these films thus appears similar to that recently reported for the exponential growth of films fabricated using a variety of biologically relevant polyelectrolytes. The use of living/controlled methods of polymerization to synthesize well-defined samples of PAA facilitates an interpretation of these differences in film behavior as arising largely from differences in polymer molecular weight and polydispersity. This work provides insight into the assembly and structure of a well-studied weak polyelectrolyte film system and illustrates the potential of living/controlled methods of polymerization to contribute to the characterization and understanding of the physical properties of these ionically cross-linked materials.     

Modulation of the functions of osteoblast-like cells on poly(allylamine hydrochloride) and poly(acrylic acid) multilayer films

Deposition of layer-by-layer polyelectrolyte multilayer (PEM) films has been a widely applied surface modification technique to improve the biocompatibility of biomaterials. The objective of this study was to investigate the impact of the deposition of poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) multilayer films on adhesion, growth and differentiation of osteoblasts-like MG63 cells. PAH and PAA were deposited sequentially onto tissue culture polystyrene at either pH 2.0 or pH 6.5 with 4-21 layers. While the MG63 cells attached poorly on the PAH/PAA multilayer films deposited at pH 2.0, while the cells adhered to the PEM films deposited at pH 6.5, depending on layer numbers. Cell adhesion, proliferation and osteogenic activities (alkaline phosphatase activity, expression of osteogenic marker genes and mineralization) were highest on the 4-layer PAH/PAA film and decreased with increasing layer numbers. On the other hand, the behavior of MG63 cells did not show any difference on the adjacent even and odd layers, except PEM4 and PEM5, i.e. the surface charges of the PAH/PAA multilayer films with over ten layers seem indifferent to osteoblastic functions. The results in this study suggested that the mechanical properties of PEM films may play a critical role in modulating the behavior of osteoblasts, providing guidance for application of PEM films to osteopaedic implants.     

Highly ion conductive poly(ethylene oxide)-based solid polymer electrolytes from hydrogen bonding layer-by-layer assembly

We report the development of a solid polymer electrolyte film from hydrogen bonding layer-by-layer (LBL) assembly that outperforms previously reported LBL assembled films and approaches battery integration capability. Films were fabricated by alternating deposition of poly(ethylene oxide) (PEO) and poly(acrylic acid) (PAA) layers from aqueous solutions. Film quality benefits from increasing PEO molecular weight even into the 10(6) range due to the intrinsically low PEO/PAA cross-link density. Assembly is disrupted at pH near the PAA ionization onset, and a potential mechanism for modulating PEO:PAA ratio within assembled films by manipulating pH is discussed. Ionic conductivity of 5 x 10(-5) S/cm is achievable after short exposure to 100% relative humidity (RH) for plasticization. Adding free ions by exposing PEO/ PAA films to lithium salt solutions enhanced conductivity to greater than 10(-5) S/cm at only 52% RH and tentatively greater than 10(-4) S/cm at 100% RH. The excellent stability of PEO/PAA films even when exposed to 1.0 M salt solutions led to an exploration of LBL assembly with added electrolyte present in the adsorption step. Fortuitously, the modulation of PEO/PAA assembly by ionic strength is analogous to that of electrostatic LBL assembly and can be attributed to electrolyte interactions with PEO and PAA. Dry ionic conductivity was enhanced in films assembled in the presence of salt as compared to films that were merely exposed to salt after assembly, implying different morphologies. These results reveal clear directions for the evolution of these promising solid polymer electrolytes into elements appropriate for electrochemical power storage and generation applications.     

Preparation of thick silica films in the presence of poly(acrylic acid) by using electrophoretic sol-gel deposition

Thick silica films were fabricated by electrophoretic sol-gel deposition of silica particles on a stainless steel sheet. Using sols prepared by the sol-gel method with poly(acrylic acid) (PAA) films of ca. 25 m in thickness were prepared with no cracks. The films were shown to be agglomerates of monodispersed silica particles with PAA. The size of the silica particles decreased with an increase in the added amount of PAA. The deposited weight was considerably larger for the films with PAA than that of the films without PAA.     

Nanoelectrode ensembles based on conductive polyaniline/poly(acrylic acid) using porous sol–gel films as template

Porous sol–gel (PSG) film has been utilized as a template for the electrochemical polymerization of aniline in presence of poly(acrylic acid) (PAA). The presence of electroactive polyaniline (PAn)/PAA within the porous skeleton of the sol–gel films has been confirmed using cyclic voltammetry, UV–vis spectrometry and atomic force microscopic measurements. The densities and the sizes of the nanoelectrodes can be controlled easily using electrochemical methods. The conductive polymer “wires” of PAn/PAA formation in PSG matrix can behave as an ensemble of closely-spaced but isolated nanoelectrodes. Moreover, the nanoelectrode ensembles based on conductive PAn/PAA for glucose biosensing are fabricated by immobilization of glucose oxidase (GOx) and Nafion onto the surface of conductive polymer. Owing to the biocompatibility of PSG and electro-activity of PAn/PAA at neutral pH regions, the glucose biosensor shows excellent characteristics and performance, such as low detection limit and fast response time.     

Assembly of nanotubes of poly(4-vinylpyridine) and poly(acrylic acid) through hydrogen bonding

Nanotubes of poly(4-vinylpyridine) (PVP) and poly(acrylic acid) (PAA) were fabricated by hydrogen bonding based on layer-by-layer (LbL) assembly. The uniform and flexible tubular structures were characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). FTIR and X-ray photoelectron spectroscopy (XPS) measurements confirm the formation of hydrogen bonds in the assembled nanotubes. PAA can be released from the assembled PAA/PVP nanotubes in a basic aqueous solution to give the walls of the tubes a porous structure. Such assembled nanotubes can be considered as carriers for catalysts or drugs, especially in aqueous solution against capillary force.     

Fluorescence staining and confocal laser scanning microscopy study of hydrogen-bonded poly(vinylpyrrolidone)/poly(acrylic acid) film

Poly(vinylpyrrolidone) (PVPON) and poly(acrylic acid) (PAA) were layer-by-layer (LBL) assembled to prepare the thin films based on hydrogen-bonding complexation. The hydrogen-bonded PVPON/PAA films were incubated in acidic, neutral and basic vapors separately. To study the morphologies after incubation, the films were stained by pH-sensitive fluorescent dyes using chemical and physical ways, and investigated with confocal laser scanning microscope (CLSM). The chemical way (labeling) was covalently linking fluoresceinamine (FAM) to some monomer units of PAA while the physical way was adsorbing rhodamine B (RB) molecules from dilute solution. Atomic force microscope (AFM) was combined with CLSM to find that after incubation in neutral or basic vapor the hydrogen-bonded PVPON/PAA films form porous structure and the pores are through the whole film.     

Photo-cross-linkable polyelectrolyte multilayers for 2-D and 3-D patterning

We report the synthesis of poly(acrylic acid-ran-vinylbenzyl acrylate) (PAArVBA), a photo-cross-linkable weak polyelectrolyte, and its incorporation into polyelectrolyte multilayer (PEM) films. PEM films assembled from PAArVBA and poly(allylamine hydrochloride) (PAH) are found to exhibit similar thickness trends with assembly pH as those previously reported for poly(acrylic acid) (PAA)/PAH multilayers. Swelling properties of the as-built and photo-cross-linked films are studied by in situ ellipsometry. Two-dimensional masking techniques are used to pattern regions of high and low swelling, as confirmed by atomic force microscopy (AFM), and to provide spatial control over the low-pH-induced microporosity transition exhibited by PAH/PAA PEMs. Films containing alternating blocks of PAH/PAArVBA bilayers and PAH/PAA bilayers were assembled, laterally photopatterned, and exposed to low-pH solution to generate nanoporosity leading to patterned Bragg reflectors, thereby demonstrating three-dimensional control over film structure in these weak PEM assemblies.     

Cell adhesion properties of patterned poly(acrylic acid)/poly(allylamine hydrochloride) multilayer films created by room-temperature imprinting technique

Patterned poly(acrylic acid) (PAA)/poly(allylamine hydrochloride) (PAH) multilayer films with line structures of different lateral size and vertical height were fabricated by a room-temperature imprinting technique, and their cell adhesion properties were investigated. The nonimprinted PAA/PAH multilayer films are cytophilic toward NIH/3T3 fibroblasts and HeLa cells whether PAA or PAH is the outer most layer. In contrast, the PAA/PAH multilayer films with a 6.5-microm-line/3.5-microm-space pattern structure are cytophobic toward NIH/3T3 fibroblasts and HeLa cells when the height of the lines is 1.29 microm. By either increasing the lateral size of the patters to 69-microm-line/43-mum-space or decreasing the height of the imprinted lines to approximately 107 nm, imprinted PAA/PAH multilayer films become cytophilic. This kind of transition of cell adhesion behavior derives from the change of the physical pattern size of the PAA/PAH multilayer films and is independent of the chemical composition of the films. The easy patterning of layer-by-layer assembled polymeric multilayer films with the room-temperature imprinting technique provides a facile way to tailor the cellular behavior of the layered polymeric films by simply changing the pattern dimensions.     

PH effects in the complex formation and blending of poly(acrylic acid) with poly(ethylene oxide)

The effect of pH on the complex formation between poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO) has been studied in aqueous solutions by turbidimetric and fluorescent methods. It was shown that the formation of insoluble interpolymer complexes is observed below a certain critical pH of complexation (pH(crit1)). The formation of hydrophilic interpolymer associates is possible above pH(crit1) and below a certain pH(crit2). The effects of polymer concentrations in solution and PEO molecular weight as well as inorganic salt addition on these critical pH values were studied. The polymeric films based on blends of PAA and PEO were prepared by casting from aqueous solutions with different pHs. These films were characterized by light transmittance measurements and differential scanning calorimetry. The existence of the pH value above which the polymers form an immiscible blend was demonstrated. The transitions between the interpolymer complex, miscible blend, and immiscible blend caused by pH changes are discussed. The recommendations for preparation of homogeneous miscible films based on compositions of poly(carboxylic acids) and various nonionic water-soluble polymers are presented.     

Influence of the degree of ionization on the growth mechanism of poly(diallyldimethylammonium)/poly(acrylic acid) multilayers

pH‐dependent growth laws of the mass coverage Γ(n) of poly(diallyldimethylammonium) chloride and poly(acrylic acid) (PAA) layer‐by‐layer films are analyzed by Quartz Crystal Microbalance‐D. (Attenuated Total Reflection)‐FTIR spectroscopy shows a degree of dissociation of acrylic acid groups in the films identical to that in solution. Apart from pH‐regimes of differently pronounced exponential and linear growth, the corresponding kinetics indicate pH‐dependent adsorption, reorganization, and diffusion processes. As the thickest films form with almost uncharged PAA (low pH), the results can only partly be explained by the dissociation degree of PAA in the film. For intermediate and high pH values chain interdiffusion as a mechanism for nonlinear growth is strongly dependent on the charge density of the PAA chains. However, at low pH other types of interactions, most likely ion–dipole interactions, play a major role in the multilayer growth. Furthermore, a change in the symmetry of growth can be observed in the low to intermediate pH range. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 425–434     

Cellular responses to patterned poly(acrylic acid) brushes

We use patterned poly(acrylic acid) (PAA) polymer brushes to explore the effects of surface chemistry and topography on cell-surface interactions. Most past studies of surface topography effects on cell adhesion have focused on patterned feature sizes that are larger than the dimensions of a cell, and PAA brushes have been characterized as cell repellent. Here we report cell adhesion studies for RBL mast cells incubated on PAA brush surfaces patterned with a variety of different feature sizes. We find that when patterned at subcellular dimensions on silicon surfaces, PAA brushes that are 30 or 15 nm thick facilitate cell adhesion. This appears to be mediated by fibronectin, which is secreted by the cells, adsorbing to the brushes and then engaging cell-surface integrins. The result is detectable accumulation of plasma membrane within the brushes, and this involves cytoskeletal remodeling at the cell-surface interface. By decreasing brush thickness, we find that PAA can be 'tuned' to promote cell adhesion with down-modulated membrane accumulation. We exemplify the utility of patterned PAA brush arrays for spatially controlling the activation of cells by modifying brushes with ligands that specifically engage IgE bound to high-affinity receptors on mast cells.     

Novel conducting polymer electrolyte biosensor based on poly(1-vinyl imidazole) and poly(acrylic acid) networks

Biosensor construction and characterization studies of poly(acrylic acid) (PAA) and poly(1-vinyl imidazole) (PVI) complex systems have been carried out. The biosensors were prepared by mixing PAA with PVI at several stoichiometric ratios, x (molar ratio of the monomer repeat units). The enzyme, invertase, was entrapped in the PAA/PVA interpenetrating polymer networks during complexation. Modifications were made on the PAA/PVI conducting polymer electrolyte matrixes to improve the stability and performance of the polymer electrolyte-based enzyme biosensor. The maximum reaction rate (V(max)) and Michaelis-Menten constant (K(m)) were investigated for the immobilized invertase. The temperature and pH optimization, operational stability, and shelf life of the polymer electrolyte biosensor were also examined.     

Film stability during postassembly morphological changes in polyelectrolyte multilayers due to acid and base exposure

The mechanism of the transition from a continuous morphology to a porous morphology within polyelectrolyte multilayers (PEMs) of linear poly(ethylene imine) (LPEI) and poly(acrylic acid) (PAA) and poly(allylamine hydrochloride) (PAH) and PAA assembled by the layer-by-layer (LbL) technique is examined. These morphological changes were created by both acidic and basic postassembly treatments. Basic postassembly treatment is shown to create different types of porosity than acidic postassembly treatment. The morphological variation from the introduction of porosity to the collapse of these porous structures and the dissolution of films under postassembly treatments was observed by AFM, optical microscopy, quartz crystal microbalance (QCM), and SEM. These morphological transitions which are a result of structural rearrangement of weak polyelectrolytes due to pH changes are closely related to the neutralization of the polycations and the ionization of polyanions. Results obtained from FTIR spectroscopy and QCM confirm that polyelectrolytes are being selectively or partially released from the polyelectrolyte multilayers thin films (PEMs) in response to the pH treatment as a function of exposure time. In conclusion, here new information is presented about the structural reorganization found in a number of weak polyelectrolyte systems. This information will be useful in designing functional materials based on polyelectrolytes.     

Multilayered assemblies composed of brilliant yellow and poly(allylamine) for an optical pH sensor.

Multilayered thin films containing poly(allylamine) (PAA) and brilliant yellow (BY) were prepared on a quartz slide by a layer-by-layer (LBL) deposition technique. The UV-visible spectra of the PAA/BY films were sufficiently changed depending upon the pH value of the solution in which the film was immersed. The response of the PAA/BY films was very fast (within a second) upon pH change from 9.0 to 5.0, while the response time was ca. 100 s upon pH change from 5.0 to 9.0.     

Voltammetric and waveguide spectroelectrochemical characterization of ultrathin poly(aniline)/poly(acrylic acid) films self-assembled on indium-tin oxide

We report on the spectroelectrochemical characterization of conducting polymer (CP) films, composed of alternating layers of poly(aniline) (PANI) and poly(acrylic acid) (PAA), deposited on ITO-coated, planar glass substrates using layer-by-layer self-assembly. Absorbance changes associated with voltammetrically induced redox changes in ultrathin films composed of only two bilayers (ITO/PANI/PAA/PANI/PAA) were monitored in real time using a unique multiple reflection, broadband attenuated total reflection (ATR) spectrometer. CP films in contact with pH 7 buffer undergo a single oxidation/reduction process, with ca. 12.5% of the aniline centers in the film being oxidized and reduced. The ATR spectra indicate that during an anodic sweep, the leucoemeraldine form of PANI in these films is oxidized to generate both the emeraldine and pernigraniline forms simultaneously. A comparison of the behavior observed during anodic and cathodic sweeps suggests that the rate of oxidation is limited by structural changes in the polymer film originating in electrostatic repulsion between positively charged PANI chains.     

Formation of high-capacity protein-adsorbing membranes through simple adsorption of poly(acrylic acid)-containing films at low pH

Layer-by-layer polyelectrolyte adsorption is a simple, convenient method for introducing ion-exchange sites in porous membranes. This study demonstrates that adsorption of poly(acrylic acid) (PAA)-containing films at pH 3 rather than pH 5 increases the protein-binding capacity of such polyelectrolyte-modified membranes 3-6-fold. The low adsorption pH generates a high density of -COOH groups that function as either ion-exchange sites or points for covalent immobilization of metal-ion complexes that selectively bind tagged proteins. When functionalized with nitrilotriacetate (NTA)-Ni(2+) complexes, membranes containing PAA/polyethylenimine (PEI)/PAA films bind 93 mg of histidine(6)-tagged (His-tagged) ubiquitin per cm(3) of membrane. Additionally these membranes isolate His-tagged COP9 signalosome complex subunit 8 from cell extracts and show >90% recovery of His-tagged ubiquitin. Although modification with polyelectrolyte films occurs by simply passing polyelectrolyte solutions through the membrane for as little as 5 min, with low-pH deposition the protein binding capacities of such membranes are as high as for membranes modified with polymer brushes and 2-3-fold higher than for commercially available immobilized metal affinity chromatography (IMAC) resins. Moreover, the buffer permeabilities of polyelectrolyte-modified membranes that bind His-tagged protein are ~30% of the corresponding permeabilities of unmodified membranes, so protein capture can occur rapidly with low-pressure drops. Even at a solution linear velocity of 570 cm/h, membranes modified with PAA/PEI/PAA exhibit a lysozyme dynamic binding capacity (capacity at 10% breakthrough) of ~40 mg/cm(3). Preliminary studies suggest that these membranes are stable under depyrogenation conditions (1 M NaOH).     

Photolithographically patterned surface modification of poly(dimethylsiloxane) via UV-initiated graft polymerization of acrylates

Patterned surface modification of poly(dimethylsiloxane) (PDMS) is achieved by combining ultraviolet-initiated graft polymerization (UV-GP) and photolithography. Poly(acrylic acid) (PAA) and poly(methacrylic acid) (PMAA) patterns were grafted onto PDMS with micrometer-scale feature edge resolution. The morphology and chemical composition of the grafted layers were assessed by optical and atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and XPS imaging. AFM section analyses demonstrated the deposition of 33 +/- 1 and 62 +/- 8 nm thick patterned films of PAA and PMAA, respectively. Spatially resolved C 1s XPS provided images of carboxylic acid functionalities, verifying the patterned deposition of acrylate films on PDMS. These observations demonstrate the general usefulness of UV-GP and photolithography for micropatterning.     

Design and Synthesis of a Fluorescently End-Labeled Poly(β-amino ester): Application to the Characterization of Degradable Polyelectrolyte Multilayers

We report the synthesis of a fluorescently end-labeled analog of a synthetic and degradable cationic poly(β-amino ester) (PBAE; polymer 1) used in past studies for the delivery of DNA and the layer-by-layer assembly of erodible polyelectrolyte multilayers (PEMs). The synthesis of an analog of polymer 1 having acrylate functionalized end groups provided a platform for the introduction of fluorescent labels by post-polymerization conjugate addition of amine-functionalized fluorophores. This approach enabled the synthesis of fluorescently end-labeled polymer (polymer 1(FL)) with molecular weights and polydispersities (M(n) = 18,000; PDI ~1.8) similar to those used in past studies for the fabrication of PEMs using polymer 1. Layer-by-layer assembly of PEMs using polymer 1(FL) and poly(styrene sulfonate) enabled characterization of film erosion and, for the first time, direct observation of the release of cationic polymer from these assemblies using fluorescence microscopy and fluorometry. Our results shed new light on the behaviors of the cationic components of these PEMs and could prove useful for the design of thin films for a range of different controlled release applications. Our results also provide new fluorescent cationic polymer probes that could be useful for characterization of the behaviors of PBAEs in other fundamental or applied biotechnological contexts.     

Layer-by-layer assembly of salt-containing polyelectrolyte complexes for the fabrication of dewetting-induced porous coatings

The layer-by-layer (LbL) assembly of salt-containing nonstoichiometric polyelectrolyte complexes (PECs) with oppositely charged uncomplexed polyelectrolyte for the fabrication of dewetting-induced porous polymeric films has been systematically investigated. Salt-containing poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) complexes (noted as PAH-PAA) with a molar excess of PAH were LbL assembled with polyanion poly(sodium 4-styrenesulfonate) (PSS) to produce PSS/PAH-PAA films. The structure of the PAH-PAA complexes is dependent on the concentration of NaCl added to their aqueous dispersions, which can be used to tailor the structure of the LbL-assembled PSS/PAH-PAA films. Porous PSS/PAH-PAA films are fabricated when salt-containing PAH-PAA complexes with a large amount of added NaCl are used for LbL assembly with PSS. In-situ and ex-situ atomic force microscopy measurements disclose that the dewetting process composed of pore nucleation and pore growth steps leads to the formation of pores in the LbL-assembled PSS/PAH-PAA films. The present study provides a facile way to fabricate porous polymeric films by dewetting LbL-assembled polymeric films comprising salt-containing PECs.