The salting-out effect and phase separation in aqueous solutions of sodium phosphate salts and poly(propylene glycol)

Phase diagrams and liquid–liquid equilibrium (LLE) data of the aqueous poly(propylene glycol) (PPG) + di-sodium hydrogen phosphate and PPG + tri-sodium phosphate two-phase systems have been determined experimentally at 298.15, 303.15, 308.15, 313.15 and 318.15 K. The effects of temperature and charge on the anion of electrolyte on the binodal curves and tie-lines have been studied and it was found that an increasing in temperature and charge on the anion caused the expansion of two-phase region. The results show that the effect of charge on the anion of electrolyte on the binodal curves becomes smaller by increasing temperatures. It was also found that the concentration of salt, which is in equilibrium with a certain concentration of PPG, decreases by increasing temperature. Based on cloud point values, the energetics of the clouding process has been estimated and it was found that entropy increase is the driving force for biphasic formation.     

Volumetric and viscosity studies of interactions between sodium phosphate salts and poly(propylene glycol) 400 in aqueous solutions at different temperatures

Density and sound velocity at the 288.15–313.15 K and viscosity at the 298.15–313.15 K temperature range at 5 K intervals for polypropylene glycol (PPG) in aqueous solutions of sodium di-hydrogen phosphate, di-sodium hydrogen phosphate and tri-sodium phosphate with salt mass fractions 0.00, 0.010 and 0.020 are reported at atmospheric pressure. From the experimental density and sound velocity data, the apparent specific volume, excess specific volume, isentropic compressibility and isentropic compressibility deviation values have been determined. The infinite dilution apparent specific volume and isentropic compressibility values of PPG have been obtained and from which the infinite dilution apparent specific volumes of transfer of PPG from water to aqueous sodium phosphate solutions have been obtained for the investigated salt concentrations and temperatures. The excess specific volume, isentropic compressibility and viscosity deviation are negative and decrease in magnitude as temperature, concentration of sodium phosphate and charge on the anion of electrolyte increases.     

Liquid-liquid phase equilibria of aqueous two-phase systems containing salts and polyethylene glycol

Liquid-liquid phase equilibria of the ternary systems: (a) polyethylene glycol - ammonium sulfate- water and (b) polyethylene glycol - sodium carbonate -water have been determined experimentally at 15°, 25°, 35° and 45°C and for two different molecular weights of the polymer (Avg. M.W. 1000 and 2000). Details of the glass cell and of the equilibration and analytical procedures used are described. Equilibrium data along with phase diagrams are presented. Finally the effect of temperature and of the molecular weight of the polymer are also discussed.     

Protein partitioning in poly(ethylene glycol)/sodium polyacrylate aqueous two-phase systems

The partition of hemoglobin, lysozyme and glucose-6-phosphate dehydrogenase (G6PDH) in a novel inexpensive aqueous two-phase system (ATPS) composed by poly(ethylene glycol) (PEG) and sodium polyacrylate (NaPA) has been studied. The effect of NaCl and Na(2)SO(4), pH and PEG molecular size on the partitioning has been studied. At high pH (above 9), hemoglobin partitions strongly to the PEG-phase. Although some precipitation of hemoglobin occurs, high recovery values are obtained particularly for lysozyme and G6PDH. The partitioning forces are dominated by the hydrophobic and electrochemical (salt) effects, since the positively charged lysozyme and negatively charged G6PDH partitions to the non-charged PEG and the strongly negatively charged polyacrylate enriched phase, respectively.     

Partitioning behavior of erythrocytes in aqueous two-phase systems containing hydroxypropyl starch and polyethylene glycol

The partitioning behavior of erythrocytes in Reppal PES 200 (a hydroxypropyl starch produced by Reppe Glykos AB, V?xj?, Sweden)-polyethylene glycol (PEG) and in dextran (Dx)-PEG aqueous phase systems made isotonic with phosphate is similar in a number of ways: (i) There is a correlation between the relative electrophoretic mobilities and partition ratios, P, of red blood cells from different species; (ii) The cell P is reduced when, at constant polymer concentrations, phosphate is systematically replaced by sodium chloride (with the total concentration isotonic); (iii) The cell P is increased with reduced polymer concentrations (decreased interfacial tensions); (iv) Treatment of erythrocytes with neuraminidase results in a reduced P value; (v) Rat red cells of different ages can be fractionated by counter-current distribution; and (vi) Differences between red blood cells from genetically distinct rats or between humans can be detected. Aquaphase (a hydroxypropyl starch marketed by Perstorp AB, Lund, Sweden) has been tested as in ii-iv above with analogous results. The partitioning behavior of erythrocytes in PES-PEG and Dx-PEG aqueous phase systems containing sodium chloride differs in a number of ways: (vii) The correlation, apparent in Dx-PEG systems, between the P value of red blood cells from different species and the ratio of their membrane poly- to monounsaturated fatty acids is absent in PES-PEG systems. It is replaced by a correlation as in i; (viii) The increase in P value in Dx-PEG observed from red blood cells after treatment with neuraminidase is replaced by a decrease in P value in PES-PEG or Aquaphase-PEG systems. We conclude that PES (and Aquaphase) can be substitutes for dextran in cell partitioning studies when charge-sensitive phases are used (e.g., those containing phosphate) while separations based on properties reflected by Dx-PEG systems containing sodium chloride are not duplicated by PES-PEG (and probably not by Aquaphase-PEG). The hydroxypropyl starch-PEG systems containing sodium chloride, unlike the analogous Dx-PEG systems, have a significant electrostatic potential difference between the phases.     

Extraction mechanism of sulfamethoxazole in water samples using aqueous two-phase systems of poly(propylene glycol) and salt

Based on the poly(propylene glycol)₄₀₀ (PPG₄₀₀)–salt aqueous two-phase system (ATPS), a green, economical and effective sample pretreatment technique coupled with high performance liquid chromatography was proposed for the separation and determination of sulfamethoxazole (SMX). The extraction yield of SMX in PPG₄₀₀–salt ATPS is influenced by various factors, including the salt species, the amount of salt, pH, and the temperature. Under the optimum conditions, most of SMX was partitioning into the polymer-rich phase with the average extraction efficiency of 99.2%, which may be attributed to the hydrophobic interaction and salting-out effect. This extraction technique has been successfully applied to the analysis of SMX in real water samples with the recoveries of 96.0–100.6%, the detection limits of 0.1 μg L⁻¹, and the linear ranges of 2.5–250.0 μg L⁻¹.     

Phase separation in aqueous two-phase systems containing poly(ethylene glycol) and magnesium sulphate at different temperatures

New experimental (liquid + liquid) equilibrium data have been determined for aqueous systems containing poly(ethylene glycol) of nominal molar mass 10,000 and magnesium sulphate at T = (295.15, 301.15, 305.15, and 311.15) K. The effect of temperature on the liquid compositions of coexisting phases is discussed. The experimental (liquid + liquid) equilibrium data of the systems were correlated by non-random two-liquid (NRTL) activity coefficient model. The interaction parameters of the NRTL activity coefficient model are obtained and reported. The calculated root mean square deviations (RMSD) showed that NRTL activity coefficient model can be used satisfactorily to correlate the (liquid + liquid) equilibrium data in aqueous solution of the {poly(ethylene glycol) + magnesium sulphate} system.     

(Liquid + liquid) and (liquid + solid) equilibrium of aqueous two-phase systems containing poly ethylene glycol di-methyl ether 2000 and di-sodium hydrogen phosphate

(Liquid + liquid) equilibrium (LLE) for the {poly ethylene glycol di-methyl ether 2000 (PEGDME₂₀₀₀) + Na₂HPO₄ + H₂O} system have been determined experimentally at T = (298.15, 308.15, 313.15, and 318.15) K. The effects of temperature on the binodals and tie-lines for the investigated aqueous two-phase system (ATPS) have been studied. An empirical non-linear expression developed by Merchuk was used for reproducing the experimental binodal data. In this work, the three fitting parameters of the Merchuk equation were obtained with the temperature dependence expressed in the linear form with (T ? T₀) K as a variable. Furthermore, the modified local composition segment-based NRTL and Wilson models and also osmotic virial equation were used to describe the LLE data of the studied system. Also, the effects of the type of salt on LLE are discussed. In addition, the effects of end groups of the polymers PEGDME₂₀₀₀ and poly ethylene glycol 2000 on phase forming ability were studied. The complete phase diagram for the poly ethylene {glycol di-methyl ether 2000 (PEGDME₂₀₀₀) + Na₂HPO₄ + H₂O} system has also been determined at T = 298.15 K.     

Neopenthyl glycol containing poly(propylene azelate)s: Synthesis and thermal properties

Poly(neopenthyl azelate) (PNAz) and poly(propylene/neopenthyl azelate) random copolymers (PPAz-PNAz) (NAz unit content from 5 to 20 mol%) were synthesized and characterized in terms of chemical structure and molecular weight. Afterwards, the polyesters were examined by TGA, DSC and X-ray diffractometry. Good thermal stability was found for each sample. The thermal analysis showed that the T_m of the copolymers decreased with the increment in NAz unit content, differently from T_g, which on the contrary increased. X-ray diffraction measurements allowed the identification of the PPAz crystalline structure in all the copolymers. Multiple endotherms were shown in the PPAz-PNAz samples, due to melting and recrystallization processes, similarly to PPAz. The of the copolymers was derived from the application of the Hoffman-Weeks’ method. Baur’s equation described well the T_m-composition data. The isothermal crystallization kinetics were analyzed according to Avrami’s treatment. The introduction of NAz units decreased the crystallization rate compared to pure PPAz. Values of the Avrami’s exponent n close to 3 were obtained in all cases, regardless of T_c, in agreement with a crystallization process originating from predeterminated nuclei and characterized by a three dimensional spherulitic growth.     

Partition of macromolecules and cell particles in aqueous two-phase systems based on hydroxypropyl starch and poly(ethylene glycol)

The partition behavior of proteins, nucleic acids, cell membranes, cell organelles and whole cells has been studied in liquid-liquid two-phase systems composed of water, poly-(ethylene glycol), and an hydroxypropyl starch. The properties of the systems are in many respects comparable with the traditional poly(ethylene glycol)-dextran systems, but the cost is reduced to around one-fifth.     

Phase separation in mixtures of poly(ethylene glycol monomethylether) and poly(propylene glycol) oligomers

Time-resolved light scattering was employed to investigate kinetics of phase separation in mixtures of poly (ethylene glycol monomethylether) (PEGE)/poly (propylene glycol) (PPG) oligomers. Phase diagrams for PEGE/PPG of varying molecular weights were established by means of cold point measurements. The oligomer mixtures reveal an upper critical solution temperature (UCST). Several temperature quench experiments were carried out with a 60/40 PEGE/PPG blend by rapidly quenching from a single phase (69°C) to two-phase temperatures (66–61°C) at 1°C intervals. As is typical for oligomer mixtures, the early stage of spinodal decomposition (SD) was not detected. The kinetics of phase decomposition was found to be dominated by the late stage of SD. Time-evolution of scattering intensity was analyzed in accordance with nonlinear and dynamical scaling theories. The time dependence of the peak intensity I_m and the corresponding peak wavenumber q_m was found to follow the power-law {I_m(t)? t^α, q_m(t)? t^-β} with the values of α = 3 ± 0.3 and β = 1 ± 0.2, which are very close to the values predicted by Siggia. This process has been attributed to a coarsening mechanism driven by surface tension. In the temporal scaling analysis, the structure function reveals university with time, suggesting self-similarity. Phase separation dynamics in 60/40 PEGE/PPG resembles the behavior predicted for off-critical mixtures.     

Glass transition in poly(propylene glycol) networks

Difficulty in controlling and determining the structural parameters of polymer networks has hindered experimental studies on the glass transition in crosslinked polymers. A series of wellcharacterized networks of poly(propylene glycol) having narrow network chain-length distributions and average molecular weight between crosslinks M _c in the range of 425–3000 has been prepared. The glass transition temperatures T_g of these networks were found to vary linearly with M , consistent with several theoretical treatments. Both the physical crosslinking and the incorporation of crosslinking agent into the system (a “copolymer” effect) are shown to be responsible for increase in T_g upon crosslinking in this system. Varying the network chain-length distribution without changing M _c did not affect the T_g of the system. The chemical nature of the crosslinking agent, however, does affect the T_g of the network, particularly at high crosslink densities.     

Partitioning of biomaterials in aqueous two-phase systems of mixed cationic-anionic surfactants

In a previous paper, we have showed that, when aqueous solutions of cationicand anionic surfactants at certain concentrations were mixed, the solution separatedspontaneously into two immiscible phases (aqueous two-phases), one phase was rich,and the other was poor in the mixed surfactants. A clear interfacial boundary existsbetween two phases.     

铟在聚乙二醇-硫酸铵双水相体系中的分配

研究了稀散元素铟在有配合剂PAR（4－（2－吡啶偶氮）－间苯二酚）存在和无PAR存在的聚乙二醇PEG－（NH4）2SO4双水相体系中的分配行为。讨论了酸度、PEG分子量、PEG浓度及温度等因素对铟分配比的影响,发现酸度对分配比的影响最大,随着PEG分子量的增加及温度的上升分配比逐渐增大;随着PEG浓度的增加分配比逐渐减小。     

Vapour pressures,densities, and viscosities of the aqueous solutions containing (triethylene glycol or propylene glycol) and (LiCl or LiBr)

In this work, new results for density, viscosity, and vapour pressure of (triethylene glycol or propylene glycol) in H₂O with LiCl or LiBr systems over temperatures ranging from 303.15 K to 343.15 K are presented. For each ternary system, four systems of which (4 to 25) mass% salt mixed with various glycols (50 to 80) mass% were studied. Incorporated with the pseudo-solvent approach, a vapour pressure model based on the mean spherical approximation for aqueous electrolyte solutions was used to represent the measured vapour pressure of the investigated systems. The present density and viscosity results were also correlated as a function of temperature and composition. The correlations yield satisfactory results. Compared to the conventionally used liquid desiccants, the vapour pressures of the systems studied yield smaller values of vapour pressures. The properties presented in this work are, in general, of sufficient accuracy for most engineering-design calculations.     

Partitioning and assembly of metal particles and their bioconjugates in aqueous two-phase systems

The behavior of metal nanospheres and nanowires and their bioconjugates in aqueous two-phase systems (ATPS) is described. The ATPS used in this work comprised poly(ethylene glycol) (PEG), dextran, and water or aqueous buffer. Au and Ag nanospheres less than 100 nm in diameter partition between the PEG-rich and dextran-rich phases on the basis of their surface chemistry and can be separated on this basis. Larger Au nanospheres and wires accumulate at the interface between the two aqueous phases. The influence of polymer molecular weight and concentration on interfacial assembly of Au wires is described. DNA-derivatized nanowires at the aqueous/aqueous interface retain the ability to selectively bind to fluorescent complementary DNA. In addition, Au nanoparticles have been bound to Au wires via selective DNA hybridization at the ATPS interface. Transmission electron microscopy and thermal denaturation experiments confirm that DNA-driven assembly is responsible for the formation of the nanosphere/wire assemblies. These results demonstrate the biocompatibility of the two-phase interface and point to future use as scaffolding in biorecognition-driven assembly.     

Dehydrochlorination of poly(vinyl chloride) by aqueous sodium hydroxide solution under two-phase conditions

The reaction of poly(vinyl chloride) powder with aqueous sodium hydroxide solution in the presence of quaternary ammonium or phosphonium halides yielded dehydrochlorinated products of conjugated polyene structure. The reaction was discussed in terms of a phase transfer catalytic mechanism between aqueous and polymer phases. Among the catalysts used tetrabutylammonium bromide was the best. To obtain the optimum conditions the effects of reaction temperature, the concentration of NaOH and the catalyst, and the molecular weight of poly(vinyl chloride) were investigated. Treatment of PVC films and solutions in tetrahydrofuran with aqueous NaOH solutions under two-phase conditions also produced dehydrochlorinated films and powders.     

Plasticization of biodegradable stereocomplex polylactides with poly(propylene glycol)

The plasticization of stereocomplex polylactide (scPLA) with poly(propylene glycol) (PPG) is described. The poly(L-lactide) (PLLA), poly(D-lactide) (PDLA) and PPG were completely blended in chloroform before film casting to prepare scPLA/PPG blend films. The PLLA/PDLA ratio was fixed at 50/50 (w/w). The PPG blending enhanced the stereocomplex formation of the scPLA films. The stereocomplex crystallinities of the scPLA films increased as the PPG blend ratio increased, the PPG molecular weight decreased and the PDLA molecular weight decreased. The PPG blending significantly decreased the T _g and film transparency, and improved the elongation at break of the scPLA films. The results indicated that the PPG blending had an effect on the stereocomplexation and it improved the flexibility of the scPLA films.     

Affinity partitioning of erythrocytic phosphofructokinase in aqueous two-phase systems containing poly(ethylene glycol)-bound cibacron blue. Influence of pH, ionic strength and substrates/effectors.

Phosphofructokinase (PFK) from rat erythrocyte haemolysates has a high affinity for Cibacron Blue F3G-A covalently bound to poly(ethylene glycol) (PEG-Cb) and thus the enzyme can be extracted into the top phase of poly(ethylene glycol)-dextran aqueous two-phase systems containing PEG-Cb. The pH, ionic strength and presence of substrates/effectors affect to different extents the affinity of the enzyme for PEG-Cb and the number of PEG-Cb molecules attached per molecule of PFK (the latter probably reflecting, at saturation, the influence on the aggregation state of the enzyme) and thus influence the yield of enzyme recovered in the top phase. Increasing the pH from 6 to 7 and then to 8 leads to a higher yield of PFK in the top phase. A change in pH from 6 to 7 and 8 results in an increased number of PEG-Cb molecules attached per molecule of enzyme while the affinity of PFK for PEG-Cb shows a minimum at pH 7. The ionic strength in the range 0.017-0.164 has less influence on the partitioning of PFK. The presence of substrates or effectors of the enzyme in general reduces the recovery of PFK in the top phase. Fructose 6-phosphate increases the number of PEG-Cb molecules attached but greatly reduces the affinity of PFK for PEG-Cb. In contrast, AMP slightly reduces the number of PEG-Cb molecules attached and the affinity of PFK for PEG-Cb. ATP and ATP-Mg2+ compete with PEG-Cb for the same binding sites in PFK.(ABSTRACT TRUNCATED AT 250 WORDS)