Luminescence properties of Tb3+/Sm3+ co-doped 38B2O3―31Al2O3―31SrO glasses and glass ceramics

In this paper, Tb³⁺/Sm³⁺ co-doped 38B₂O₃―31Al₂O₃―31SrO glass was successfully prepared. After heat treatment, single crystal phase SrAl₂B₂O₇ was precipitated from the parent glass. DTA data showed the glass transition temperature at 625 °C and a sharp exothermic peak at 860 °C. XRD patterns demonstrated a regular evolution from glass to glass ceramics with higher treatment temperature and longer treatment time. From the XRD patterns, we supposed that Tb³⁺/Sm³⁺ ions can be most likely contained in the crystal phase. The photoluminescence spectra showed that the crystallization can enhance the emission intensity significantly and there could be an optimum crystallization degree to get the strongest luminescence in glass ceramics. The light scattering of devitrification sample can vary the intensity ratio of Sm³⁺ and Tb³⁺ emission. Therefore, as a potential route, rare earth ions doped glass ceramics could be a further research direction of luminescence glasses for white light emitting diodes application.     

Spectroscopic properties and energy transfer in Yb3+–Ho3+ co-doped germanate glass emitting at 2.0 μm

A new kind of germanate glass co-doped with Yb³⁺–Ho3⁺ was prepared. The J-O parameters were calculated to be Ω₂ = (6.59 ± 0.21) × 10^? 20 cm², Ω₄ = (2.77 ± 0.36) × 10^? 20 cm², and Ω₆ = (1.90 ± 0.25) × 10^? 20 cm². The little overlap between the absorption cross section and stimulated emission cross section indicates a non-resonant energy transfer process. The calculation demonstrates that the energy transfer between Yb³⁺ and Ho³⁺ is one-phonon assisted in a great measure. The gain coefficient of Ho³⁺ at 2.0 μm was also calculated. The fluorescence measurement shows the Yb³⁺ co-doping enhances the 2.0 μm emission remarkably.     

Spectral investigations on VO2+ ion doped in CaO–SrO–Na2O–B2O3 glass systems

Glasses of the (20 ? x)CaO–xSrO–(20 ? y)Na₂O–60B₂O₃ ? y (CSNB) system with (5 ≤ x ≤ 15) mol% and y = 0.1 mol% of V₂O₅ were characterized by X-ray diffraction (XRD), EPR (Electron Paramagnetic Resonance), Optical absorption Spectra and FT-IR (Fourier transform Infrared Spectroscopy) studies. EPR spectra of all the glass samples exhibit resonance signals characterstic of VO²⁺ ions. The values of spin-Hamiltonian parameters indicate that the VO²⁺ ions in CSNB glasses were present in octahedral sites with tetragonal compression and belong to C_4v symmetry. Spin-Hamiltonian parameters ‘g’ and ‘A’ were evaluated. The Optical band energy (E_opt) and Urbach energy (ΔE) were calculated from their ultra violet edges. By correlating EPR and Optical data the molecular orbital coefficients have been evaluated. IR spectra of these glasses were analyzed in order to identify the contribution of each component to the local structure that determines the physical properties of these glasses.     

Enhanced 2.0 μm emission and energy transfer in Yb3+/Ho3+/Ce3+ triply doped tellurite glass

Ce³⁺ induced enhancement of Ho³⁺ ~ 2.0 μm emission in Yb³⁺/Ho³⁺ codoped sodium–zinc–tellurite (TNZ) glass was achieved under 980 nm LD laser excitation. The spectroscopic studies show that the upconversion is remarkably reduced by the presence of Ce³⁺. The ~ 2.0 μm fluorescence intensity is nearly triply enhanced, and the energy transfer efficiency from Yb³⁺ to Ho³⁺ is improved from 16.1% to 42.6% by increasing the Ce³⁺ concentration from 0 to 0.8 mol%. The mechanism responsible for the upconversion reduction and ~ 2.0 μm emission enhancement in Yb³⁺/Ho³⁺/Ce³⁺ triply-doped TNZ glass is also discussed. Our results indicate that the Yb³⁺/Ho³⁺/Ce³⁺ triply-doped TNZ glass is a promising candidate material for improving the Ho³⁺ 2.0 μm fiber laser performance.     

Excited state absorption and up-conversion luminescence of Ho3+ centres in 3CaO–Ga2O3–3GeO2 glass

3CaO–Ga₂O₃–3GeO₂ glass excited state absorption spectra-activated with Ho³⁺ (Ho₂O₃ – 0.7 wt% content) have been measured and analysed. Up-converted emission channels have been identified and the predicted up-converted emission bands have been registered under Ar ion laser (λ = 488 nm) excitation according to the excited state absorption data. A mechanism of up-converted transitions for Ho³⁺ centres in this prototype glass network is proposed on the basis of the obtained results.     

Characteristics and biocompatibility of Na2O–K2O–CaO–MgO–SrO–B2O3–P2O5 borophosphate glass fibers

A novel Na₂O–K₂O–CaO–MgO–SrO–B₂O₃–P₂O₅ borophosphate glass fiber is prepared. The thermal properties including differential thermal analysis (DTA) and viscosity measurement of the glass were presented. The tensile strength of the glass fiber is measured. The reaction of the glass fibers in the SBF solution is characterized by XRD, FTIR and SEM. XRD and FTIR indicate that the carbonate hydroxyapatite has formed rapidly on the glass. Cell attachment, spreading and proliferation on the glass are determined by MTT [3-(4,5-Dimethylthiazol-2-yl)-2,5-Diphenyltetrazolium Bromide] assay method using Human osteosarcoma MG-63 cells. The bioactivity and biocompatibility of the glass fiber make it a good potential prospect in the field of tissue engineering.     

Visible to near-infrared down-conversion luminescence in Tb3 + and Yb3 + co-doped lithium–lanthanum–aluminosilicate oxyfluoride glass and glass-ceramics

Tb^3 + and Yb^3 + co-doped oxyfluoride glasses were fabricated in a lithium–lanthanum–aluminosilicate matrix (LLAS) by a melt-quench technique. Glass-ceramics were obtained by appropriate heat treatment of the as-prepared glasses. Visible to near-infrared down-conversion luminescence was studied for glass and glass-ceramic samples with different Yb^3 + concentrations. It has been found that the luminescence intensity at 940–1020 nm from Yb^3 + ions increases while the emission lifetime of Tb^3 + ions decreases in the glass-ceramic compared to that in the as-prepared glass, which indicates that the energy transfer efficiency increases in the glass-ceramics compared to that in the as-prepared glass. The down-conversion luminescence also increased for increasing Yb^3 + concentration from 1 mol% to 2 mol%, but decreased for the sample with a high Yb^3 + co-doping concentration of 8 mol%, which is attributed to the concentration quenching.     

Full color and tunable white emitting in ternary Ce/Tb/Sm Co-doped CaO–B2O3–SiO2 glasses

A series of luminescent glasses composed of CaO–B₂O₃–SiO₂ co-doped with cerium oxide (CeO₂), terbium oxide (Tb₄O₇) and samarium oxide (Sm₂O₃) were prepared by high temperature melting method, aiming to realize the white emitting and tunable luminescent color in the glass matrix. The full colors including blue, green and reddish orange emitting were observed simultaneously in the photoluminescent spectra of ternary Ce/Tb/Sm co-doped CaO–B₂O₃–SiO₂ glasses excited by ultraviolet light. It is shown that the combination of these three emitting allows the realization of white light emitting in ternary co-doped CaO–B₂O₃–SiO₂ glasses. Furthermore, the tunable luminescent color and chromaticity parameters could be realized by varying the content of dopant in the glass matrix, which makes these co-doped glasses good candidates for white light emitting diodes (LEDs).     

BaO–B2O3–SiO2–Al2O3 sealing glass for intermediate temperature solid oxide fuel cell

Glasses in the formulation close to BaSiO₃–BaB₂O₄ eutectic compound are developed for sealing of intermediate-temperature (500–650 °C) solid oxide fuel cell (IT-SOFC). Thermal and microstructural analyses of the glasses with 0–10 mol% Al₂O₃ are also conducted. Detailed crystallization kinetics and interfacial stability of the glass in contact with yttria-stabilized zirconia (YSZ) and samaria-doped ceria (SDC) are investigated and compared. The results show that the formulation, 47BaO–21B₂O₃–27SiO₂–5Al₂O₃ (G1A5), performs the best on glass forming ability (GFA) among all tested formulations, and shows matched thermal expansion and working temperature to CeO₂-based electrolytes of IT-SOFC. Two major crystalline phases that precipitate from G1A5 above 750 °C are platy hexacelsian and BaSiO₃ grains.     

Performance investigation of Li2O–Al2O3–4SiO2 based glass–ceramics with B2O3, Na3AlF6 and Na2O fluxes

Influence of single fluxes (10 wt.% B₂O₃), bi-component fluxes (4 wt.% B₂O₃ + 6 wt.% Na₃AlF₆), and complex fluxes (4 wt.% B₂O₃ + 4 wt.% Na₃AlF₆ + 2 wt.% Na₂O) on the thermal kinetic parameters, microstructure, flexural strength and coefficient of thermal expansion (CTE) of Li₂O–Al₂O₃–4SiO₂ (LAS) glass–ceramics was investigated through differential thermal analysis (DTA), X-ray diffraction (XRD), and scanning electron microscope (SEM). The results showed that complex fluxes could efficiently decrease transition temperature (T_g) and crystallization temperature (T_p), and accelerate the formation of needle-like β-spodumene crystals which benefit high flexural strength. The homogeneous LAS glass–ceramic (sample C₃) which has a high strength of 132.4 MPa and low CTE (100–650 °C) of 2.74 × 10^? 6/°C is obtained by doping of the initial LAS glass by complex fluxes of 4 wt.% B₂O₃, 4 wt.% Na₃AlF₆, and 2 wt.% Na₂O, nucleating at 630 °C/120 min and then crystallized at 780 °C/120 min. It is worthy of further investigation as a bonder of diamond composite material due to its outstanding prosperities.     

The effect of TiO2 on phase separation and crystallization of glass-ceramics in CaO–MgO–Al2O3–SiO2–Na2O system

The experiments were carried out on studying the effect of phase separation on nucleation and crystallization in the glass based on the system of CaO–MgO–Al₂O₃–SiO₂–Na₂O. In the experiments, TiO₂ was chosen as nucleating agent. Three batches of 5, 8 and 10 wt% TiO₂ substitution were investigated by the techniques of DSC, XRD, FTIR and FESEM equipped with EDS. XRD and FTIR analysis indicated that the super cooled glasses were all amorphous, the heat treatment leading to nucleation would cause a disruption of silica network which followed phase separation. The phase separation followed the generation of crystal seeds Mg(Ti, Al)₂O₆. FESEM observation and EDS analysis revealed that the more TiO₂ content of glass, the more droplet separated phase and crystal seeds after nucleation heat treatment. The main crystal phase is clinopyroxene, Ca(Ti, Mg, Al)(Al, Si)O₆, of crystallized glass.     

Formation of Co2+-doped nanocrystals in La2O3–MgO–Al2O3–SiO2 glass-ceramics

Transparent glass-ceramics were synthesized by heat-treatment of glass with a composition of 5La₂O₃–13.2MgO–28.8Al₂O₃–46SiO₂–4.5TiO₂–2.5ZrO₂–0.15CoO (LMAS) (wt.%). The activation energy of crystallization and the Avrami parameter for the LMAS glass were determined from the DTA curves at different heating rates. The most two intense bands of Raman spectrum of initial glass at ~ 810 cm^?1 and ~ 900 cm^?1 were connected with the presence of [SiO₄] and [TiO₄] tetrahedral, respectively. After heat-treated at 700 °C/10 h+820 °C/8 h, the intensity of the band for [TiO₄] tetrahedral weakened, while an intensive band at ~ 800 cm^?1 for the Ti–O bond appeared. Other bands were characteristics of high-silicate network and x(MgTi₂O₅)·y(Al₂TiO₅) polycrystals. The changes reflected phase separation after heat-treatment of the initial glass. The strong absorption band of glass-ceramics centered at 580 nm can be assigned to ⁴A₂(⁴F)→⁴T₁(⁴P) and the broad absorption band at 1100–1700 nm to ⁴A₂(⁴F)→⁴T₁(⁴F) transitions of tetrahedral coordinated Co²⁺ ion. Two broad emission bands, one was around 660 nm, the other was from 800 nm to 1050 nm, of glass-ceramics correspond to the ⁴T₁(⁴P)→⁴A₂(⁴F) and ⁴T₁(⁴P)→⁴T₂(⁴F) transitions of tetrahedral coordinated Co²⁺ ions. The absorption and emission features clearly demonstrated that Co²⁺ ions were incorporated into nanocrystals and located in tetrahedral sites.     

Spectroscopic properties of Co2+ ions in La2O3–MgO–Al2O3–SiO2 glass-ceramics

Co²⁺-doped La₂O₃–MgO–Al₂O₃–SiO₂ (LMAS) glass-ceramics was synthesized by conventional method. The microstructure of LMAS GCs heat-treated at 760 °C/12 h + 930 °C/4 h was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The spectroscopic properties of Co²⁺-doped LMAS GCs were studied by absorption spectrum, excitation spectrum, and temperature dependent luminescence spectra. XRD results revealed the sizes of MgAl₂O₄ crystalline phases are about 9.1 ± 1.5 nm. The three peaks in the visible absorption band of LMAS GCs at 549 nm, 585 nm and 626 nm are connected with the transitions from ⁴A₂ level to ²A₁/²T₂(²G), ⁴T₁(⁴P) and ²E/²T₁(²G) levels, respectively, and excitations into them emit the radiation at around 666 nm. The luminescence intensity increased with temperature increasing from 10 K to 150 K, while it weakened with temperature increasing from 150 K to 350 K. These features were explained by the effects of two competing mechanisms.     

Down conversion luminescence of Tb3+–Yb3+ codoped SrF2 precipitated glass ceramics

In the Tb³⁺–Yb³⁺ codoped glass ceramics with SrF₂ nanocrystals precipitated, the energy transfer mechanism from Tb³⁺ to Yb³⁺ was investigated. The excitation power dependence of emission intensity study showed that the quantum cutting occurs during the energy transfer from Tb³⁺ to Yb³⁺ with the excitation of Tb³⁺ high energy level. However, the one-photon process is the main reason that is responsible for the Yb³⁺ infrared emission. The external quantum yields of Tb³⁺ and Yb³⁺ were evaluated by using an integrating sphere measurement system with the excitation of 377 and 488 nm lasers, which are much lower than the expected quantum efficiencies calculated from Tb³⁺ lifetimes. The external quantum yields in the glass ceramics and as-made glasses were also compared.     

The effect of ionic and metallic silver on the crystalline phases developed in CaO–Al2O3–TiO2–P2O5 glasses

Development of crystallization in the CaO–Al₂O₃–TiO₂–P₂O₅ system glasses was investigated in the presence of ionic and metallic silver. Differential thermal analysis, X-ray diffractometry, ultra violet–visible spectrophotometry, atomic force microscopy and scanning electron microscopy were used to evaluate the resulted glasses and glass-ceramics. It was found that silver ions facilitated crystallization by decreasing the viscosity of the glasses. However, metallic silver, which was formed through heat treatment in hydrogen atmosphere, improved heterogeneous crystallization of the reduced glasses in the subsequent heat treatment. The preformed metallic silver led to effective crystallization of calcium titanium phosphate (CaTi₄(PO₄)₆), calcium metaphosphate (Ca(PO₃)₂) and calcium pyrophosphate (Ca₂P₂O₇) phases at significantly decreased temperatures. The two latter phases were partially dissolved out by leaching in acidic solution and left out a porous structure of calcium titanium phosphate glass-ceramic.     

Spectroscopic properties of the 1.8 μm emission of Tm3+/Yb3+ codoped TeO2–ZnO–Bi2O3 glasses with efficient energy transfer

Tm³⁺-doped and Tm³⁺/Yb³⁺-codoped TeO₂–ZnO–Bi₂O₃ (TZB) glasses are prepared by melt-quenching method. The Judd-Ofelt intensity parameters (Ω_t t = 2, 4, 6), radiative transition rate, and radiative lifetime of Tm³⁺ are calculated based on the absorption spectra. The 1.8 μm emission of the samples is investigated under 980 nm laser excitation. The absorption, emission cross-sections, and gain coefficient of Tm³⁺:³F₄ → ³H₆ are calculated. The energy transfer processes of Yb³⁺–Yb³⁺ and Yb³⁺–Tm³⁺ are analyzed, the results show that the Yb³⁺ ions can transfer their energy to Tm³⁺ ions with large energy transfer coefficient, and a maximum efficiency of 79%.     

Synthesis and bioactive properties of macroporous nanoscale SiO2–CaO–P2O5 bioactive glass

A macroporous nanoscale bulk bioactive glass (SiO₂–CaO–P₂O₅ system) was prepared by sol–gel co-template method. Porosimeter analysis showed that the as-synthesized bioactive glasses (BGs) had a porosity of 85% and exhibited a multimodal pore size distribution, nanopores (10–40 nm) and macropores (100 nm–10 μm). Morphological and structural characterizations showed the pores were interconnected with pore walls of about 250 nm in width and 1 μm in length. In vitro bioactivity test indicated that the as-synthesized bulk BGs exhibited faster apatite layer formation capability than the conventional sol–gel BGs. Additionally, the deposited layer was identified as hydroxycarbonate apatite, which is similar to the inorganic part of human bone.     

Effect of the ytterbium concentration on the upconversion luminescence of Yb3+/Er3+ co-doped PbO–GeO2–Ga2O3 glasses

The effect of Yb³⁺ concentration on the frequency upconversion (UPC) of Er³⁺ in PbO–GeO₂–Ga₂O₃ glasses is reported for the first time. Samples were prepared with 0.5 wt% of Er₂O₃ and different concentrations of Yb₂O₃ (1.0–5.0 wt%). The green (523 and 545 nm) and red (657 nm) emissions are observed under 980 nm diode laser excitation. The dependence of the frequency UPC emission intensity upon the excitation power was examined and the UPC mechanisms are discussed. An interesting characteristic of these glasses is the increase of the ratio of red to green emission, through an increase of the Yb³⁺ concentration due to an efficient energy transfer from Yb³⁺ to Er³⁺.     

Spinodal decomposition during continuous cooling of a PbOB2O3Al2O3 glass

Spinodal decomposition during continuous cooling of the PbOB₂O₃Al₂O₃ quasi-binary glass system was analysed by numerical integration of Cook's differential equation (which includes the contribution of random density fluctuations) for small angle X-ray scattering (SAXS) intensity. The SAXS curves derived from the calculations have a wide range of k-Fourier components (0 < k < k_c) for which a positive amplification factor occurs and they show a “crossover” point at $\text{k}{}_{\mathrm{c}}\text{= 0.155}\text{A}\text{?}{}^{\mathrm{?1}}$. The wavenumber which receives maximal amplification, k_m, increases with the cooling rate, Q, as $\text{Q}{}^{\mathrm{<mtext>1</mtext><mtext>n</mtext>}}$, with n = 10.9. This Q dependence of k_m is similar to that predicted by Huston et al., however our results show a higher value of n. The dependence on Q and k_m of the SAXS intensity I(k_m) was also deduced. The measurements of SAXS curves were performed on glass samples prepared by the splat-cooling technique. Because of the difficulties which arise in the determination of the cooling rate of the samples, the only experimental results that could be compared with the theory are the k_m dependence of I and the value of k_c. These results are satisfactorily understood in terms of the present analysis.