The pρT behaviour of the lactate family

The densities of methyl lactate, ethyl lactate and butyl lactate have been measured using a high-pressure, high-temperature vibrating tube densimeter system over a temperature range from T = (283.15 to 338.15) K and a pressure range from p = (0.1 to 60.0) MPa. The experimental densities have been satisfactorily correlated with temperature and pressure using the TRIDEN equation. Finally, from the experimental densities, properties such as isobaric expansibility and isothermal compressibility have been calculated.     

PρT measurements and derived properties of liquid 1-alkanols

The density of compressed liquid (C2 to C11) 1-alkanols was measured with a vibration tube densimeter over the temperature range from (278.15 to 358.15) K and pressures up to 60 MPa, with an uncertainty of ±0.0012 g · cm⁻³. Density values were correlated with pressure and temperature by the TRIDEN 10-parameter equation. Isothermal compressibility, isobaric thermal expansivity and internal pressure were calculated from the experimental results. The influence of the carbon-chain lengths over the thermophysical properties obtained was studied.     

Automated apparatus for the rapid determination of liquid–liquid and solid–liquid phase transitions

An automated apparatus developed for the determination of liquid–liquid and solid–liquid equilibrium temperatures with a resolution of 1 mK and a traceable accuracy of 0.01 K is described. The amount of light transmitted through six sample cells placed in a computer controlled thermostat is recorded at heating or cooling rates from 0.075 to 15 K h⁻¹. The construction does not require expensive optic equipment like lasers, glass fibre optics or photomultipliers, but is based on light emitting diodes (LED) as light sources and light dependent resistors (LDR) or photodiodes as detectors. As shown by the discussed examples, the instrument has a wide range of possible applications from the investigation of simple one-component and binary systems to the study of the complicated phase behavior of surfactant solutions.     

Optimisation of pressurised liquid extraction for the determination of p,p′-DDT and p,p′-DDE in aged contaminated Ethiopian soils

The effectiveness of extracting p,p′-DDT and p,p′-DDE from aged contaminated soil samples by means of pressurized liquid extraction (PLE) was evaluated. Two soil samples, which were contaminated more than 10 years ago, were used in the investigation. The static extraction time was optimised and then validated against the total sum of target analytes obtained from multiple sequential extractions. The PLE results were also compared with Soxhlet extraction (SOX). PLE for 3×10 min at 100 °C was proven to be more exhaustive than SOX in the determination of p,p′-DDE from both soil samples. In the case of p,p′-DDT, PLE was found to be equally as exhaustive as SOX. Additionally, most of the previous PLE investigations used hazardous organic solvents such as n-hexane, toluene and dichloromethane mixed with acetone, whereas in this investigation the less toxic solvent combination n-heptane/acetone has been employed.     

Comparison of dispersive liquid–liquid microextraction and hollow fiber liquid–liquid–liquid microextraction for the determination of fentanyl,alfentanil, and sufentanil in water and biological fluids by high-performance liquid chromatography

Dispersive liquid–liquid microextraction (DLLME) and hollow fiber liquid–liquid–liquid microextraction (HF-LLLME) combined with HPLC–DAD have been applied for the determination of three narcotic drugs (alfentanil, fentanyl, and sufentanil) in biological samples (human plasma and urine). Different DLLME parameters influencing the extraction efficiency such as type and volume of the extraction solvent and the disperser solvent, concentration of NaOH, and salt addition were investigated. In the HF-LLLME, the effects of important parameters including organic solvent type, concentration of NaOH as donor solution, concentration of H₂SO₄ as acceptor phase, salt addition, stirring rate, temperature, and extraction time were investigated and optimized. The results showed that both extraction methods exhibited good linearity, precision, enrichment factor, and detection limit. Under optimal condition, the limits of detection ranged from 0.4 to 1.9 μg/L and from 1.1 to 2.3 μg/L for DLLME and HF-LLLME, respectively. For DLLME, the intra- and inter-day precisions were 1.7–6.4% and 14.2–15.9%, respectively; and for HF-LLLME were 0.7–5.2% and 3.3–10.1%, respectively. The enrichment factors were from 275 to 325 and 190 to 237 for DLLME and HF-LLLME, respectively. The applicability of the proposed methods was investigated by analyzing biological samples. For analysis of human plasma and urine samples, HF-LLLME showed higher precision, more effective sample clean-up, higher extraction efficiency, lower organic solvent consumption than DLLME.     

Modification of the Furter equation and correlation of the vapor–liquid equilibrium for mixed-solvent electrolyte systems

Isobaric vapor–liquid equilibrium values at 1 atm pressure were measured for the systems 1-propanol–water–potassium acetate and 2-propanol–water–potassium acetate under fixed salt mole fractions using a modified Othmer recirculation still. A modified Furter equation, ln(α_s/α)=k₁z+k₂z², was proposed for correlating the effect of dissolved salts on vapor–liquid equilibrium (VLE). The modified equation contains two parameters that are applicable to the entire salt/solvent composition range. Correlation of VLE for 15 mixed-solvent electrolyte systems was made by means of the proposed modified equation with better results than those obtained from the original equation.     

In-sample acetylation-non-porous membrane-assisted liquid–liquid extraction for the determination of parabens and triclosan in water samples

A procedure for the determination of seven parabens (esters of 4-hydroxybenzoic acid), including the distinction between branched and linear isomers of propyl- and butyl-parabens and triclosan in water samples, was developed and evaluated. The procedure includes in-sample acetylation-non-porous membrane-assisted liquid–liquid extraction and large volume injection–gas chromatography–ion trap–tandem mass spectrometry. Different derivatisation strategies were considered, i.e. post-extraction silylation with N-methyl-N-(tert-butyldimethylsilyl)-trifluoroacetamide and in situ acylation with acetic anhydride (Ac₂O) and isobutylchloroformate. Moreover, acceptor solvent and the basic catalyser of the acylation reaction were investigated. Thus, in situ derivatisation with Ac₂O and potassium hydrogenphosphate (as basic catalyser) was selected. Potassium hydrogenphosphate overcomes some drawbacks of other basic catalysers, e.g. toxicity and bubble formation, while leads to higher responses. Subsequently, other experimental variables affecting derivatisation–extraction yield such as pre-stirring time, salt addition and volume of Ac₂O were optimised by an experimental design approach. Under optimised conditions, the proposed method achieved detection limits from 0.1 to 1.4 ng L⁻¹ for a sample volume of 18 mL and extraction efficiencies, estimated by comparison with liquid–liquid extraction, between 46% (for methyl- and ethyl-parabens) and 110% (for benzylparaben). The reported sample preparation approach is free of matrix effects for parabens but affected for triclosan with a reduction of ≈ 40% when wastewater samples are analysed; therefore, both internal and external calibration can be used as quantification techniques for parabens, but internal standard calibration is mandatory for triclosan. The application of the method to real samples revealed the presence of these compounds in raw wastewater at concentrations up to 26 ng mL⁻¹, the prevalence of the linear isomer of propylparaben (n-PrP), and the coexistence of the two isomers of butylparaben (i-BuP and n-BuP) at similar levels.     

Ab Initio Study of the Oxygen Atom Abstracting Hydrogen from Difluoromethane and Dichloromethane

ThemajorfiresuppressionagentsusedinconfinedspacesortoprotectelectronicsareCFsBrandCF2ClBr.Howeverbecauseoftheirozonedepletionpotential,theirproductionisnowbanned.Thesearchfornewflamesuppressantswhichareeffective,nontoxicandhaveIowglobalenvironmentalimpacthassparkedincreasedinterestinthemechanismsoffiresuppressionandthedevelopmentofpredictiveflamemodels1-2.KineticdataforthereactionsofOatomswithhalogenatedmethanesareneededtomodelthecombustionchendstry.Manystudiesaboutithavebeencarriedoutbyex…     

Molecular simulation of the phase behaviour of ternary fluid mixtures: the effect of a third component on vapour–liquid and liquid–liquid coexistence

The Gibbs ensemble algorithm is implemented to determine the vapour–liquid and liquid–liquid phase coexistence of dilute ternary fluid mixtures interacting via a Lennard–Jones potential. Calculations are reported for mixtures with a third component characterised by different intermolecular potential energy parameters. Comparison with binary mixture data indicates that the choice of energy parameter for the third component affects the composition range of vapour–liquid substantially. The addition of a third component lowers the energy of liquid phase while slightly increasing the energy of the vapour phase.     

Application of dispersive liquid–liquid microextraction and reversed phase-high performance liquid chromatography for the determination of two fungicides in environmental water samples

Dispersive liquid–liquid microextraction (DLLME) has been developed for the extraction and preconcentration of diethofencarb (DF) and pyrimethanil (PM) in environmental water. In the method, a suitable mixture of extraction solvent (50 µL carbon tetrachloride) and dispersive solvent (0.75 mL acetonitrile) are injected into the aqueous samples (5.00 mL) and the cloudy solution is observed. After centrifugation, the enriched analytes in the sediment phase were determined by HPLC-VWD. Different influencing factors, such as the kind and volume of extraction and dispersive solvent, extraction time and salt effect were investigated. Under the optimum conditions, the enrichment factors for DF and PM were both 108 and the limit of detection were 0.021 ng mL^?1 and 0.015 ng mL^?1, respectively. The linear ranges were 0.08–400 ng mL^?1 for DF and 0.04–200 ng mL^?1 for PM. The relative standard deviation (RSDs) were both almost at 6.0% (n = 6). The relative recoveries from samples of environmental water were from the range of 87.0 to 107.2%. Compared with other methods, DLLME is a very simple, rapid, sensitive (low limit of detection) and economical (only 5 mL volume of sample) method.     

Ionic liquid based dispersive liquid–liquid microextraction for the extraction of pesticides from bananas

This paper describes a dispersive liquid–liquid microextraction (DLLME) procedure using room temperature ionic liquids (RTILs) coupled to high-performance liquid chromatography with diode array detection capable of quantifying trace amounts of eight pesticides (i.e. thiophanate-methyl, carbofuran, carbaryl, tebuconazole, iprodione, oxyfluorfen, hexythiazox and fenazaquin) in bananas. Fruit samples were first homogenized and extracted (1 g) with acetonitrile and after suitable evaporation and reconstitution of the extract in 10 mL of water, a DLLME procedure using 1-hexyl-3-methylimidazolium hexafluorophosphate ([C₆MIM][PF₆]) as extraction solvent was used. Experimental conditions affecting the DLLME procedure (sample pH, sodium chloride percentage, ionic liquid amount and volume of disperser solvent) were optimized by means of an experimental design. In order to determine the presence of a matrix effect, calibration curves for standards and fortified banana extracts (matrix matched calibration) were studied. Mean recovery values of the extraction of the pesticides from banana samples were in the range of 69–97% (except for thiophanate-methyl and carbofuran, which were 53–63%) with a relative standard deviation lower than 8.7% in all cases. Limits of detection achieved (0.320–4.66 μg/kg) were below the harmonized maximum residue limits established by the European Union (EU). The proposed method, was also applied to the analysis of this group of pesticides in nine banana samples taken from the local markets of the Canary Islands (Spain). To the best of our knowledge, this is the first application of RTILs as extraction solvents for DLLME of pesticides from samples different than water.     

Optimization of parameters for the alcoholic-assisted dispersive liquid–liquid microextraction of estrogens in water

Extraction and determination of estrogens in water samples were performed using alcoholic-assisted dispersive liquid–liquid microextraction (AA-DLLME) and high-performance liquid chromatography (UV/Vis detection). A Plackett–Burman design and a central composite design were applied to evaluate the AA-DLLME procedure. The effect of six parameters on extraction efficiency was investigated. The factors studied were volume of extraction and dispersive solvents, extraction time, pH, amount of salt and agitation rate. According to Plackett–Burman design results, the effective parameters were volume of extraction solvent and pH. Next, a central composite design was applied to obtain optimal condition. The optimized conditions were obtained at 220 μL 1-octanol as extraction solvent, 700 μL ethanol as dispersive solvent, pH 6 and 200 μL sample volume. Linearity was observed in the range of 1–500 μg L^?1 for E2 and 0.1–100 μg L^?1 for E1. Limits of detection were 0.1 μg L^?1 for E2 and 0.01 μg L^?1 for E1. The enrichment factors and extraction recoveries were 42.2, 46.4 and 80.4, 86.7, respectively. The relative standard deviations for determination of estrogens in water were in the range of 3.9–7.2 % (n = 3). The developed method was successfully applied for the determination of estrogens in environmental water samples.     

Structure–property relationships of blended polysaccharide and protein biomaterials in ionic liquid

Cellulose and silk blended biomaterial films were regenerated from ionic liquid solution and investigated to characterize and understand the effect of inter- and intra-molecular interactions upon the morphology and thermal properties. The blended films were dissolved in 1-allyl-3-methylimidazolium chloride ionic liquid, coagulated and regenerated with water. Various characterization techniques were implemented to characterize structural, morphological and thermal properties: FTIR, SEM, TGA, DSC and X-ray scattering. The results showed that the cellulose microcrystalline structure and β-sheets from the silk can be disrupted by inter- and intra-molecular hydrogen bonds forming intermediate semicrystalline or amorphous structures. The SEM showed morphological effects of such interactions that cause varying thermal degradation and glass transition temperature. The X-ray scattering confirms such findings at the molecular level, demonstrating that the cellulose microfibril diameter decreases as the silk content increases. It also shows that the β-sheets size increases as the cellulose content increases. These various techniques provide evidence that suggest the hydrogen bonds between the β-sheets and the glucose units in the cellulose chains control the thermal and structural properties of the blended films, changing the morphology and physicochemical properties.     

Vapor–liquid equilibria for systems of diethyl carbonate and ketones and determination of group interaction parameters for the UNIFAC and ASOG methods

Densities and speeds of sound for the binary mixtures acetone, 2-butanone and 2-pentanone + diethyl carbonate, over the whole composition range, at T = 298.15 K and atmospheric pressure have been measured. Excess molar volumes and deviations in isentropic compressibility for the binary systems were fitted to the Redlich–Kister polynomial. Isobaric vapor–liquid equilibria for the binary systems acetone + diethyl carbonate, 2-butanone + diethyl carbonate and 2-pentanone + diethyl carbonate at P = 101.3 kPa have been determined. The activity coefficients were calculated to be thermodynamically consistent and they were correlated with the Wilson, NRTL, UNIQUAC and Redlich–Kister equations. Interaction parameters related to the carbonate (OCOO) and ketone (CO) groups, in ASOG and UNIFAC methods, have been determined using our experimental VLE data.     

A reliable prediction of the global phase stability for liquid–liquid equilibrium through the simulated annealing algorithm: Application to NRTL and UNIQUAC equations

The simulated annealing algorithm is introduced to search the global optimal solutions for the multipeak phenomena which generally exist in the phase stability problems with continuous variables. The Gibbs free energy criterion was modeled by the NRTL and UNIQUAC activity coefficient equations. When previous approaches fail, it is usually because they locate local minima due to the nonconvex and nonlinear natures of the models used to predict phase equilibrium. In this paper, the preliminary results show that the global minimum of the tangent plane distance function (TPDF) can be obtained by using the simulated annealing algorithm. The effects of the initial and the final values of the control parameter, the decrement of the control parameter and the length of the Markov chains are analyzed. The optimal `cooling schedule' was obtained according to the calculation results of the phase stability problems for one ternary mixture. The liquid–liquid equilibrium compositions were calculated by the Newton–Raphson method on the basis of the global minimum of TPDF. The results of four examples show that the simulated annealing algorithm can effectively solve the global phase stability problem.     

Structure and reactivity of the polarised liquid–liquid interface: what we know and what we do not

Charge transfer phenomena at the interface between two immiscible electrolyte solutions (ITIES) are electrochemical reactions taking place in soft media. Owing to their liquid nature, the ITIES shows a large panel of electrochemical reactions including electron transfer reactions, ion transfer reactions, coupled electron–ion transfer reactions or biomimetic redox reactions. Nevertheless, the mechanisms by which these reactions proceed are yet to be fully understood. The goal of this short review is to summarise the work accomplished over the past decades towards the elucidation of the structure and reactivity at the ITIES, highlighting the main questions still to be answered.     

Flotation-assisted dispersive liquid–liquid microextraction method for preconcentration and determination of trace amounts of cobalt: Orthogonal array design

A simple, rapid, and efficient flotation-assisted dispersive liquid–liquid microextraction method was developed for preconcentration of trace amount of cobalt(II) ions. In this technique, a mixture of toluene and methanol (20: 80, v/v) was injected through the septum in the bottom of a narrow-bore tube containing cobalt solution. Afterwards, the fine droplets of extraction solvent were formed and cobalt (as 1-nitroso-2- naphtol complex) was collected on the surface of solution by aeration. The effect of different variables on the extraction efficiency of cobalt such as pH of solution, ligand concentration and injection volume was investigated using orthogonal array design. At optimum conditions, the calibration curve was linear over the range of 10–1000 μg/L. The detection limit, relative standard deviation and enrichment factor were 3 μg/L, 3.9% (n = 10) and 120, respectively. The developed method was successfully applied to the determination of cobalt in water and drug samples.