HPLC study of tissue distribution of loganin in rats

A rapid, sensitive and selective high performance liquid chromatography (HPLC) method was developed and validated for determination of loganin in rat tissues. Samples were prepared based on a simple protein precipitation. Separation of loganin was achieved on a reversed-phase C(18) column (250 x 4.6 mm, 5 microm) with a mobile phase consisting of acetonitrile and water (16:84, v/v) at a flow rate of 1.0 mL/min. The detection wavelength was set at 236 nm and the temperature of the column was kept at 30 degrees C. The method was applied to study tissue distribution of loganin in rats after a single administration of loganin at a dose of 20 mg/kg. The highest level was observed in kidney, then in stomach, lung and small intestine. The lowest level was found in brain. The peak levels were attained at 90 min in most tissues. It was indicated that kidney was the major distribution tissue of loganin in rats, and that loganin had difficulty in crossing the blood-brain barrier. It was also found there was no long-term accumulation of loganin in rat tissues.     

Utilization of cyanobacteria in photobioreactors for orthophosphate removal from water

The effectiveness of photosynthetic free-living and polyurethane foam (PU) immobilized Anabaena variabilis cells for, removal of orthophosphate (P) from water in batch cultures and in a photobioreactor was studied. Immobilization in PU foams was found to have a positive effect on P uptake by cyanobacteria in batch cultures. The efficiency of P uptake by immobilized cells was higher than by free-living cells. A laboratory scale photobioreactor was constructed for removal of P from water by the immobilized cyanobacteria. The photobioreactor was designed so that the growth medium (water) from a reservoir was pumped through a photobioreactor column with immobilized cyanobacteria and back to the reservoir. This created a closed system in which it was possible to measure P uptake. No leakage of cells into the photobioreactor medium reservoir was observed during the operation. The immobilized cells incorporated into a photobioreactor column removed P continuously for about 15 d. No measurable uptake was demonstrated after this period. Orthophosphate uptake efficiency of 88–92% was achieved by the photobioreactor.     

高温非平衡条件下氟原子亲电动力学的激波管研究

To study electron affinity kinetics, a shock tube method was applied, in which the test gas was ionized by a reflected shock wave and subsequently quenched by a strong rarefaction wave. As the quenching speed of 106 K/s was reached, a nonequilibrium ionization recombination process occurred, which was dominated by ion recombination with electrons. A Langmuir electrostatic probe was used to monitor variation in the ion number density at the reflection shock region. The working state of the probe was analyzed, and a correction was introduced for reduction of the probe current due to elastic scattering in the probe sheath. The three body electron affinity rate coefficient of the fluorine atom over the temperature range 1200 to 2200 K in an ambiance of argon gas was directly determined. The temperature dependence of electron affinity rate coefficient was discussed.     

燃料电池电极制作方法的研究

对燃料电池,性能良好的催化剂至关重要,它决定着大电流密度放电时的性能、成本和运行寿命［１］．但因电极上的反应是气、液、固三相反应,所以必须制备出高效的、结构合理的气体电极［２～３］,减小气相、液相传质阻力,提高三相接触性能,降低电极极化．Ｋ．Ｍｕｎｄ等［４～５］所制作的电极,气体扩散距离长,溶解气体的扩散电阻大．Ｒ．Ｐ．Ｉｃｚｋｏｗｓｋｉ等人［６］用ＰＴＦＥ（ｐｏｌｙｔｅｔｒａｆｌｕｏｒｏｅｔｈｙｌｅｎｅ,聚四氟乙烯）作疏水剂,在整个气体反应层制成气体扩散通道,改善了电极性能．后来,Ｓ．Ｍｏｔ…     

Flow injection analysis of DPPH radical based on electron spin resonance

In order to construct a rapid and selective determination system of free radicals, we developed an FIA system using an electron spin resonance (ESR) spectrophotometer (flow injection spin analysis) equipped with a flow-through flat cell. In the present investigation, 1,1-diphenyl-2-picrylhydrazyl (DPPH) was used as a model free radical. Using a single line flow system, 0.5 mM DPPH was repetitively injected. When the magnetic field was fixed at 335.3 mT, the largest change in the ESR signal was observed and obtained peak height was proportional to the concentration of DPPH radical. A double line flow system was constructed in which a carrier stream containing 0.15 mM DPPH was fed into the flat cell after confluence with a sample stream. When ascorbic acid was injected as a typical DPPH radical scavenger, a negative peak appeared in proportional to the concentration. Lower detection limit of ascorbic acid was 0.01 mM (S/N=4), sampling frequency was 13 samples per h, and a satisfactory reproducibility (CV=3.2%, 0.1 mM, n=5) was obtained. The present system was also applied to estimate the DPPH radical-scavenging activity of other substances and food samples.     

离子印迹传感器选择性检测甲基汞离子

以甲基汞离子为模板,8-巯基喹啉为荧光单体,4-乙烯基吡啶为功能单体,乙二醇二甲基丙烯酸酯为交联剂,偶氮二异丁腈为引发剂,在二甲基亚砜溶剂中,以聚偏氟乙烯(PVDF)膜为支撑介质,65℃热引发聚合得到甲基汞离子荧光印迹膜。该荧光印迹膜对甲基汞离子表现出良好的选择性,最佳吸附pH值为7.0,检出限为3.5×10-7mol/L。将其作为吸附材料,应用于河水中甲基汞离子的分离和富集,结果表明,该传感器对甲基汞离子具有良好的选择性和特异性吸附,回收率达93%～104%。     

Selective enrichment of anti-inflammatory drugs from river water samples by solid-phase extraction with a molecularly imprinted polymer

A molecularly imprinted polymer (MIP) is synthesised by a noncovalent protocol in which ibuprofen was used as a template molecule. The polymer was evaluated chromatographically and it was seen that the MIP showed cross-reactivity. Subsequently, when this polymer was used as sorbent in SPE it was possible to selectively extract a mixture of nonsteroidal anti-inflammatory drugs from aqueous samples when a cleanup step with dichloromethane was performed. The performance of the MIP was evaluated with river water and water from a wastewater treatment plant, and compared with the performance of a commercial Isolute ENV+ sorbent.     

Purification of Pseudomonas sp. Lipase by Continuous Elution Electrophoresis Based on Pb^2＋ Precipitation Method

A Pb^2 precipitation method was designed to get rid of the impure proteins in a lipase. The results show that it was a simple way in the primary treatment of the crude samples and about 20% impure proteins were removed in the precipitation step. Further, continuous elution electrophoresis was also applied as a preparative technique for attaining the highly pure lipase. During the continuous elution electrophoresis, the enzyme was eluted as a single peak and 5.7-fold purification was achieved in a yield of 54.3%. The two steps finally yielded an electrophoretically homogeneous enzyme.     

Phase-transfer agents as catalysts for a nucleophilic substitution reaction in microemulsions

The reaction between 4-tert-butylbenzyl bromide and potassium iodide was carried out in microemulsions based on different nonionic surfactants, and the reaction rates were compared with those obtained in two-phase systems with added phase-transfer agent, either a quaternary ammonium salt or a crown ether. The reactions were relatively fast in the microemulsions and extremely sluggish in the two-phase systems without additional phase-transfer agent. Addition of a phase-transfer agent did not accelerate the reaction when a hydrocarbon was used as organic solvent, neither in the two-phase system nor in the microemulsion. When a chlorinated hydrocarbon was used as solvent, phase-transfer catalysis became effective and the rate obtained in the two-phase system with an equimolar amount of phase-transfer agent added was higher than that obtained in the microemulsion. When a catalytic amount of phase-transfer agent was used, the rate in the two-phase system was about the same as the rate obtained in the microemulsion without the phase-transfer agent. The combined approach, that is, use of a microemulsion as the reaction medium and addition of a phase-transfer agent, gave the highest reaction rate. The quaternary ammonium salt (tetrabutylammonium hydrogen sulfate) was a more efficient catalyst in the microemulsion system than the crown ether ([18]crown-6).     

In vitro screening of the action of non-steroidal anti-inflammatory drugs on hypochlorous acid-induced hyaluronan degradation

The antioxidative effect of two non-steroidal anti-inflammatory drugs was studied in vitro by measuring the kinetics of degradation of high-molecular weight hyaluronan (HA) in a system comprising hypochlorous acid + CuCl₂ + ascorbic acid using a Brookfield rotational viscometer equipped with a Teflon cup and spindle of coaxial cylindrical geometry. The changes in HA chemical structure were investigated by chemiluminometry. When sodium naproxen was added to the system during a running degradative process its inhibitory effect was clearly shown. The inhibition was dependent on the drug concentration. However, when this drug was added to the system before the initiation of HA degradation, no inhibition was seen even at the highest drug concentration tested. The inhibitory effect of acetylsalicylic acid was achieved with a relatively low concentration of the drug and was independent of the experimental model used.     

On-line enzymatic reaction,extraction, and chromatography of fatty acids and triglycerides with supercritical carbon dioxide

Supercritical carbon dioxide can be utilized both as an introduction solvent in capillary SFC and as a reaction medium; both possibilities are illustrated in this study. An off-line SFE unit was modified for on-line SFE-SFC. To facilitate rapid depressurization of the extraction cell and to prevent memory effects, a 6-port valve was installed at the outlet line of the extraction unit. An increased background signal was obtained when PEEK polymer was used in the construction of the extraction vessel; when stainless steel was used, the blanks improved. The synthesis of methyl esters and butyl esters of fatty acids from triglycerides in edible fat was examined using an immobilized lipase as a catalyst in on-line SFE-SFC. As a result of 30 minutes reaction – extraction time, high yields of fatty acid esters were obtained at a pressure of 150 bar and a temperature of 50°C.     

LED光诱导化学发光法检测饮料中的核黄素

以化学发光法为基础,建立了以发光二极管(LED)诱导化学发光体系(LED-CL)检测饮料中核黄素含量的分析方法。样品溶液与鲁米诺溶液混合后由蠕动泵带出,经LED灯照射后产生化学发光,产生的化学发光信号由光电检测器检测。核黄素浓度检测线性范围为0.39~79.56μg/L(R≥0.999 7),加标回收率为99.3%~103%,可用于饮料中核黄素的检测。     

Quantitative determination of L-DOPA in tablets by high performance thin layer chromatography

A densitometric high performance thin-layer chromatographic (HPTLC) method was developed and validated for quantitative analysis of L-DOPA in tablets. Chromatographic separation was achieved on precoated silica gel F 254 HPTLC plates using a mixture of acetone-chloroform-n-butanol-acetic acid glacial-water (60:40:40:40:35 v/v/v/v/v) as mobile phase. Quantitative analysis was carried out at a wavelength of 497 nm. The method was linear between 100 and 500 ng/microL, with a correlation coefficient of 0.999. The intra-assay variation was between 0.26 and 0.65% and the interassay was between 0.52 and 2.04%. The detection limit was 1.12 ng/microL, and the quantification limit was 3.29 ng/microL. The accuracy ranged from 100.40 to 101.09%, with a CV not higher than 1.40%. The method was successfully applied to quantify L-DOPA in real pharmaceutical samples, including the comparison with HPLC measurements. The method was fast, specific, with a good precision, and accurate for the quantitative determination of L-DOPA in tablets.     

Rational Design and Application of a Redox‐Active,Photoresponsive, Discrete Metallogelator

A photoresponsive discrete metallogelator was rationally designed by incorporating a photochromic azobenzene subunit in the structure of a redox‐active ferrocene–peptide conjugate. The target molecule was purposefully equipped with a dipeptide unit capable of self‐assembly in response to sonication. The designed molecule was shown to undergo supramolecular self‐assembly and achieve organogelation in response to ultrasound, light, heat, and redox signals. The sol–gel phase transition of the designed gelator was found to be sensitive to a plethora of input stimuli, allowing the application of the sol–gel transition behavior in basic logic gate operations. A gel‐based NOT logic gate operation was realized when the redox‐active property of the organogel was examined by using different oxidizing agents. The smart response of the gelator was further exploited in designing XOR operations under oxidizing or non‐oxidizing conditions.     

Determination of antihyperglycemic biguanides in serum and urine using an ion-pair solid-phase extraction technique followed by HPLC-UV on a pentafluorophenylpropyl column and on an octadecyl column

An HPLC-UV method was established for the determination of metformin and buformin in biological fluids. Metformin was not retained on particles packed in conventional solid-phase extraction cartridges; in contrast, buformin was retained too firmly and not eluted with a solvent for recovery. However, both drugs were retained on particles that had been treated with an ion-pair reagent of heptanesulfonate or dodecylsulfate and recovered almost completely. The recovered fraction was subjected to HPLC on a pentafluorophenylpropyl column which was suitable for the determination of both biguanides in serum and in urine. Limits of quantitation were low enough for clinical use, and reproducibility was high with an RSD of 0.9-2.3%. HPLC on a conventional octadecyl column was suitable only for the determination of buformin in serum since interfering peaks appeared on the chromatograms of urine samples. The method was applied to analysis of some clinical specimens.     

New Phosphane Based on a β‐Cyclodextrin,Exhibiting a Solvent‐Tunable Conformation,and its Catalytic Properties

A new diphenylphosphane based on a β‐cyclodextrin skeleton that exhibits a dual solubility in water and in organic solvent was synthesised. Interestingly, a solvent‐dependent conformation change was evidenced by NMR spectroscopy studies; the self‐inclusion of a phenyl group of the phosphane moiety into cyclodextrin cavity observed in water disappeared in organic solvents due to a change in conformation. Hydrogenation or hydroformylation reactions performed in water and in organic solvents showed that this ligand was able to stabilise catalytically active rhodium species in solution. In the case of the hydroformylation reaction, it was demonstrated that regioselectivity was influenced by the solvent‐dependent conformation of the ligand.     

微流控芯片电泳/电化学检测人单个肝癌细胞中的谷胱甘肽

采用微流控装置结合电化学检测研究了测定人单个血红细胞中谷胱甘肽(GSH)的方法。在该方法中,细胞的进样、定位、溶膜以及细胞中谷胱甘肽的转移和检测都在配有通道端安培检测器的双T形芯片中完成。单个细胞用液压导入到双T的交界面,在电泳缓冲液中毛地黄皂苷的作用下,细胞膜被穿孔。再施加直流电压,细胞被溶膜。释放出来的GSH被此直流电压电迁移至通道端并在Au/Hg电极上被检测。用校正曲线法可以定量测定单个细胞中的GSH。     

Cationic Emulsion Polymerization of Octamethylcyclotetrasiloxane (D4) in Mixtures with Alkoxysilanes

The cationic emulsion polymerization of octamethylcyclotetrasiloxane (D4) in mixtures with methyltriethoxysilane (MTES) and vinyltriethoxysilane (VTES) was studied by FTIR ATR, GC, the development of a toluene insoluble fraction of the polymer and a gravimetric analysis. The polymerization of D4 alone was also conducted for comparison and, additionally, the development of molecular weight of polydimethylsiloxane (PDMS) obtained in that process was studied by GPC. Dodecylbenzenesulphonic acid (DBSA) was used as a surfactant and catalyst. The process was carried out in a “starved feed” mode by adding dropwise the monomer mixture to the aqueous solution of DBSA. FTIR ATR spectra were recorded by the sensor placed in the probe tip of a ReactIR 15^TM apparatus. It was found that the silicone polymer formation proceeded faster when D4 was polymerized in the mixture with alkoxysilanes, especially in the beginning of the process, and that already at the beginning of the process, the partly crosslinked polymer was formed. The induction period of ca. 30 min was observed and the concentration of cyclic siloxanes (D4 and decamethylcyclopentasiloxane—D5) remained at a very low level in the course of the reaction and only traces were detected in the final product. The particle size development in the course of the reaction was also studied and it was found that the particle size distribution was bimodal and was broadening as the reaction proceeded, though this phenomenon was less distinct when D4 was polymerized in the mixtures with alkoxysilanes. The structure of the reaction product was confirmed by ²⁹Si NMR.     

Bioprocess for solubilization of rock phosphate on starch based medium by Paecilomyces marquandii immobilized on polyurethane foam

Paecilomyces marquandii, a phosphate-solubilizing, starch-utilizing filamentous fungus, was immobilized on polyurethane foam (PUF). The immobilized fungus was applied in a repeated batch (six batches) fermentation process to solubilize Hirapur rock phosphate. The fungus was immobilized on PUF cubes and was used for phosphate solubilization in shake flask repeated batch cultivations. The fungus was also immobilized on PUF sheet and utilized in an airlift bioreactor in a repeated batch process. Maximum soluble phosphate (370 μg/ml) was recorded after third batch with 8 g rock phosphate/l. After 12 days of fermentation, a total production of 1,643 μg phosphate/ml was achieved.     

TRANSTHYRETIN (PREALBUMIN) GENE IN HUMAN PRIMARY HEPATIC CANCER

From a subtracting cDNA library constructed from normal liver versus human primary hepatic cancer (PHC), a cDNA clone pG8 was isolated. Using it as a probe, RNA extracted from one human liver and 9 PHC samples were analyzed by Northern hybridization. As expected, its mRNA was highly expressed in liver; however, the expression was strikingly suppressed in PHC. Only weak signal was observed in 2 out of 9 PHC, while no signal was detectable in the other 7 samples. Utilizing pG8 as a probe, DNA from the same PHC specimens was analyzed after MspI digestion and Southern hybridization. Deletion of DNA fragment was observed in 4 out of 9 samples. In further study of cancer and non-cancerous liver from other 7 PHC patients, similar deletion of DNA fragments in cancer was observed in 4 out of 7 samples. After sequencing of the clone of 572 bp, it was unexpectedly found that pG8 was completely homologous to the coding sequence of transthyretin, TTR gene, as TTR (or prealbumin) gene has been known to be linked to a