Morphology,rheological and crystallization behavior in non-covalently functionalized carbon nanotube reinforced poly(butylene succinate) nanocomposites with low percolation threshold

Multi-walled carbon nanotubes (CNTs) were non-covalently functionalized by surface wrapping of poly(sodium 4-styrenesulfonate) (PSS) with the aid of ultrasound. The functionalized CNTs were incorporated into poly(butylene succinate) (PBS) through solution coagulation to fabricate CNTs filled PBS nanocomposites. The morphologies of the PBS/CNT nanocomposites were studied by scanning electron microscope (SEM) and transmission electron microscope (TEM), and the effect of loading of functionalized CNT on the rheological behavior, electrical conductivity and mechanical properties of the nanocomposites was investigated systemically. SEM observation indicates that functionalized CNTs dispersed in PBS matrix without obvious aggregation and showed good interfacial adhesion with the PBS phase. TEM observation reveals that a CNT network was formed when the loading of CNTs increased from 0.1 to 0.3 wt%. Rheological investigation indicates the formation of a CNT network with a percolation threshold of only 0.3 wt%. Significant improvement in electrical conductivity occurred at CNT loading of 0.3 wt%, with the value of electrical conductivity increasing by six orders of magnitude compared to neat PBS. Differential scanning calorimetry indicates that the melt crystallization temperature of PBS was improved by ∼14 °C with addition of only 0.05 wt% functionalized CNTs. Tensile tests indicate that both the yield strength and Young's modulus of PBS were apparently reinforced by incorporation of functionalized CNTs, while the elongation at break was reduced gradually.     

Chitosan‐Functionalized Carbon Nanotubes as Support for the High Dispersion of PtRu Nanoparticles and their Electrocatalytic Oxidation of Methanol

Carbon nanotubes (CNTs) were non‐covalently functionalized with chitosan (Chit) and then employed as the support for PtRu nanoparticles. The functionalization was carried out at room temperature without the use of corrosive acids, thereby preserving the integrity and the electronic conductivity of the CNTs. Transmission electron microscopy reveals that PtRu nanoparticles were highly dispersed on the surface of Chit‐functionalized CNTs (CNT‐Chit) with small particle‐size. Cyclic voltammetry studies indicated that the PtRu nanoparticle/CNT‐Chit nanohybrids have a higher electrochemical surface area, electrocatalytic performance, and stability towards methanol oxidation compared to PtRu nanoparticles supported on the pristine CNTs.     

Evaluating the effect of addition of nanodiamond on the synergistic effect of graphene-carbon nanotube hybrid on the mechanical properties of epoxy based composites

Addition of carbon nanotubes (CNT) to Graphene (Gr) is seen to have synergistic effect as reinforcement to polymer matrix. This is possible as CNTs inhibit stacking of Gr sheets, thus providing larger surface area nanophase to get bonded with polymer matrix and providing mechanical support through load sharing and crack growth inhibition. However, tube like morphology and high aspect ratio of CNT often lead to entanglement, which restricts their effect in exfoliating Gr. The aim of the present study is to investigate the potential of ND in improving the synergistic effect of Gr-CNT hybrid as a reinforcement to epoxy matrix. This study utilizes the power of ultrasonication technique, which is very simple and scalable, for dispersing and incorporating nanofillers into epoxy matrix. Addition of ND to Gr-CNT epoxy composite improved the tensile strength from ~46% with 0.5 wt% (75Gr:25ND) to ~51% with 0.8 wt% (25Gr:25CNT:50ND) as compared to neat epoxy. While the fracture toughness improved from ~140% with 0.5 wt% (25Gr:75CNT) to 165% with 0.8 wt% (25Gr:50CNT:25ND). Fractured surfaces of composites revealed improved dispersion and strong interfacial interaction with addition of ND to Gr-CNT hybrid. NDs attaches to the surface of Gr inhibit the stacking of Gr sheets by restricting π-π stabilization. NDs also help in bridging the ends of CNTs together into long chains, thereby increasing the aspect ratio of the fiber like reinforcement. This increases the total available surface area of CNTs and Gr, to interact with epoxy matrix, improves the overall efficiency of Gr-CNT hybrid as a reinforcement, resulting into improvement in mechanical properties of the composite structure.     

A strategy for the high dispersion of PtRu nanoparticles onto carbon nanotubes and their electrocatalytic oxidation of methanol

Carbon nanotubes (CNTs) were non-covalently functionalized by 1-pyrenecarboxaldehyde (PCA) via π-π stacking interactions. PCA not only acts as the reductant for the deposition of PtRu nanoparticles, but the oxidation product of PCA can also effectively anchor and stabilize the in-situ-produced PtRu?NPs on the surface of CNTs. Transmission electron microscopy demonstrates that PtRu?NPs are uniformly dispersed on the surface of CNTs with small particles sizes of about 1.7 nm. The obtained PtRu-NP/CNT composites have higher electrochemical surface areas, electrocatalytic activities, and better stability towards methanol oxidation compared to PtRu?NPs supported on pristine CNTs.     

Evolution of Fiber Morphologies during Poly (acrylonitrile) Electrospinning

Summary: In this study, we used a facile approach to examine the evolution of fiber morphologies during electrospinning, via solidifying the newly electrospun polyacrylonitrile (PAN) nanofibers in an ethanol bath at different electrospinning distances (2 cm to 10 cm). It has been observed that a massive jet-thinning took place at the initial stage of whipping instability, followed by uneven fiber-stretching. The fiber-stretching at the later whipping stage was mainly concentrated on beaded fiber sections, which improved the uniformity of the resultant fibers.     

Relations between the aspect ratio of carbon nanotubes and the formation of percolation networks in biodegradable polylactide/carbon nanotube composites

The biodegradable polylactide composites containing carbon nanotubes (CNTs) with high aspect ratio (HAR) and low aspect ratio (LAR) were prepared by melt mixing. The physical properties of those two systems were characterized in terms of rheology, conductivity, and mechanical properties for establishing preliminary structure–property relations. Several viscoelastic models were then used to further describe the relations between aspect ratio and percolation network of CNTs. The results show that these two CNTs present different structural characteristics in the polylactide (PLA) matrix during melt mixing: the LAR CNTs are far stiffer than the HAR CNTs. At low loading levels, the former is dispersed as bent fibers or their small bundles, whereas the latter is dispersed as self‐entangled flocs, presenting far larger hydrodynamic radius than the former. At high loading levels, both are dispersed as flocs due to strong tube–tube interactions. However, the two CNTs show approximate average floc size and mesh size because they present same rigid length and effective aspect ratio. At identical loadings, therefore, the HAR CNTs have more total number of flocs than that of the LAR CNTs, forming network with more compact structure and imparting higher contributions to properties of the composites as a result. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 479–489, 2010     

Electrical and melt rheological characterization of PC and co‐continuous PC/SAN blends filled with CNTs: Relationship between melt‐mixing parameters,filler dispersion,and filler aspect ratio

Electrical and melt rheological properties of melt‐mixed polycarbonate (PC) and co‐continuous PC/poly(styrene–acrylonitrile) (SAN) blends with carbon nanotubes (CNTs) are investigated. Using two sets of mixing parameters, different states of filler dispersion are obtained. With increasing CNT dispersion, an increase in electrical resistivity near the percolation threshold of PC–CNT composites and (PC + CNT)/SAN blends is observed. This suggests that the higher mixing energies required for better dispersion also result in a more severe reduction of the CNT aspect ratio; this effect was proven by CNT length measurements. Melt rheological studies show higher reinforcing effects for composites with worse dispersion. The Eilers equation, describing the melt viscosity as function of filler content, was used to fit the data and to obtain information about an apparent aspect ratio change, which was in accordance with measured CNT length reduction. Such fitting could be also transferred to the blends and serves for a qualitatively based discussion. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 79–88     

Thermal transfer,interfacial, and mechanical properties of carbon fiber/polycarbonate-CNT composites using infrared thermography

Electrical resistance (ER) and thermogram measurements were used to evaluate thermal transfer, interfacial and mechanical properties of carbon fiber reinforced thermoplastic polycarbonate composites. Carbon nanotubes (CNTs) were fairly uniformly dispersed in polycarbonates using a solvent dispersion method. The CNTs were then further dispersed with an additional time using a twin screw extruder. The effect of CNT on the mechanical properties of polycarbonate was evaluated using a thin film tensile test. For thermogram to evaluate the transferring temperature the composite was placed on a hotplate and copper wires were inserted in the composite at uniform thickness intervals. Due to the different inherent thermal conductivity of CNT, ER was measured to detect thermal changes in the carbon fiber/CNT-polycarbonate composites. The comparison of interlaminar shear strength (ILSS) was to investigate effects of CNT on mechanical and interfacial properties. The uniform distribution of CNTs affected all of these properties in carbon fiber-reinforced thermoplastic composite. Furthermore, heat transfer and heat release become more rapid with the addition of CNT than the without case.     

碳纳米管纤维的连续制备及高性能化

碳纳米管纤维是一种碳纳米管的宏观聚集体,是由碳纳米管及管束组装而成的连续纱线,具有高强、高韧、高导电等特性,在结构功能一体化复合材料、纤维状能源器件、人工肌肉以及轻质导电线缆等领域具有非常广泛的应用前景。经过近二十年的发展,碳纳米管纤维材料在连续制备技术、高性能化以及应用探索等方面相继取得了突破性的研究进展。本文总结了碳纳米管纤维材料的发展历程,对比介绍了碳纳米管纤维的不同连续制备与组装技术,重点讨论了碳纳米管纤维结构与性能之间的关联规律,并对目前碳纳米管纤维的高性能化方法进行了综述。在此基础上,对碳纳米管纤维材料的发展思路以及未来的应用方向进行了展望。     

Thermomechanical and structural characterization of polybutadiene/poly(ethylene oxide)/CNT stretchable electrospun fibrous membranes

It is difficult to produce rubbery polymer nanofibers, that is, polybutadiene, by the method of electrospinning, since during electrospinning rubbery polymer fibers join and entangles due to their low T_g. For this reason, it is not easy to achieve the fiber form out of these polymers. Homogeneously electrospun carbon nanotubes (CNT)‐filled polybutadiene (PBu) and poly(ethylene oxide) (PEO) composite elastomeric fibers exhibit distinctive physical features such as uniform fiber diameter and distribution with significant improvements in thermomechanical properties. Controlled hydrophilicity/hydrophobicity with the components allows to generate homogenous, thermally stable and stretchable bio‐composite scaffold, and fibrous antibacterial membrane scaffolds out of PBu/PEO/CNT composite. We have combined the exciting properties of PEO with high pore density with the rubber elasticity of PBu via dissolving them in a dichloromethane/ethyl acetate organic solvent, and subsequently producing electrospun woven fibers with different PBu/PEO ratios. Frequency‐dependent thermomechanical characterization via dynamic mechanical analysis reveals pronounced changes in the onset and extent of melting, as well as the storage and loss modulus values at the onset of melting, in particular when small amounts (1.25% by wt%) of CNTs are present. The characteristic bands were detected for the PBu/PEO and PBu/PEO/CNT samples by means of Raman and Fourier‐transform infrared spectroscopy. CNT addition increases the hydrophobicity via the increase in roughness as attained by atomic force microscopy.     

Carbon Nanotube Fibers Decorated with MnO2 for Wire-Shaped Supercapacitor

Fibers made from CNTs (CNT fibers) have the potential to form high-strength, lightweight materials with superior electrical conductivity. CNT fibers have attracted great attention in relation to various applications, in particular as conductive electrodes in energy applications, such as capacitors, lithium-ion batteries, and solar cells. Among these, wire-shaped supercapacitors demonstrate various advantages for use in lightweight and wearable electronics. However, making electrodes with uniform structures and desirable electrochemical performances still remains a challenge. In this study, dry-spun CNT fibers from CNT carpets were homogeneously loaded with MnO₂ nanoflakes through the treatment of KMnO₄. These functionalized fibers were systematically characterized in terms of their morphology, surface and mechanical properties, and electrochemical performance. The resulting MnO₂–CNT fiber electrode showed high specific capacitance (231.3 F/g) in a Na₂SO₄ electrolyte, 23 times higher than the specific capacitance of the bare CNT fibers. The symmetric wire-shaped supercapacitor composed of CNT–MnO₂ fiber electrodes and a PVA/H₃PO₄ electrolyte possesses an energy density of 86 nWh/cm and good cycling performance. Combined with its light weight and high flexibility, this CNT-based wire-shaped supercapacitor shows promise for applications in flexible and wearable energy storage devices.     

Controlled Nanofiber Composed of Multi‐Wall Carbon Nanotube/Poly(Ethylene Oxide)

We have successfully fabricated poly(ethylene oxide) (PEO) nanofibers containing embedded multi‐wall carbon nanotubes (MWCNTs). An initial dispersion of the MWCNTs in distilled water was achieved using sodium dodecyl sulfate. Subsequently, the dispersion was decanted into a PEO solution, which enabled separation of the MWCNTs and their individual incorporation into the PEO nanofibers on subsequent electrospinning. Initially, the carbon nanotube (CNT) rods were randomly oriented, but owing to the sink‐like flow in the electrospinning wedge, they became gradually oriented along the streaming direction, in order that oriented CNTs were obtained on entering the electrospun jet. Individual MWCNTs became embedded in the nanofibers, and were mostly aligned along the fiber axis. Evidence of load transfer to the nanotubes in the composite nanofiber was observed from the field‐emission scanning electron microscopy, transmission electron microscopy and conductivity data.     

Comparative study of the electrochemical behavior and analytical applications of (bio)sensing platforms based on the use of multi-walled carbon nanotubes dispersed in different polymers

This review present a critical comparison of the electrochemical behavior and analytical performance of glassy carbon electrodes (GCE) modified with carbon nanotubes (CNTs) dispersed in different polymers: polyethylenimine (PEI), PEI functionalized with dopamine (PEI-Do), polyhistidine (Polyhis), polylysine (Polylys), glucose oxidase (GOx) and double stranded calf-thymus DNA (dsDNA). The comparison is focused on the analysis of the influence of the sonication time, solvent, polymer/CNT ratio, and nature of the polymer on the efficiency of the dispersions and on the electrochemical behavior of the resulting modified electrodes. The results allow to conclude that an adequate selection of the polymers makes possible not only an efficient dispersion of CNTs but also, and even more important, the building of successful analytical platforms for the detection of different bioanalytes like NADH, glucose, DNA and dopamine.     

碳纳米管/聚丙烯腈原液的制备及可纺性

通过原位聚合的方法制备了碳纳米管／聚丙烯腈复合材料原液,并采用湿纺成型工艺制得碳纳米管／聚丙烯腈复合材料纤维。与共混工艺相比较,采用该方法制得的碳纳米管／聚丙烯腈复合材料碳纳米管在聚丙烯腈基中分散均匀,具有较好的可纺性。     

Functional groups modulate the sensitivity and electron transfer kinetics of neurochemicals at carbon nanotube modified microelectrodes

The surface properties of carbon-based electrodes are critically important for the detection of biomolecules and can modulate electrostatic interactions, adsorption and electrocatalysis. Carbon nanotube (CNT) modified electrodes have previously been shown to have increased oxidative sensitivity and reduced overpotential for catecholamine neurotransmitters, but the effect of surface functionalities on these properties has not been characterized. In this study, we modified carbon-fiber microelectrodes (CFMEs) with three differently functionalized single-wall carbon nanotubes and measured their response to serotonin, dopamine, and ascorbic acid using fast-scan cyclic voltammetry. Both carboxylic acid functionalized and amide functionalized CNTs increased the oxidative current of CFMEs by approximately 2-6 fold for the cationic neurotransmitters serotonin and dopamine, but octadecylamine functionalized CNTs resulted in no significant signal change. Similarly, electron transfer was faster for both amide and carboxylic acid functionalized CNT modified electrodes but slower for octadecylamine CNT modified electrodes. Oxidation of ascorbic acid was only increased with carboxylic acid functionalized CNTs although all CNT-modified electrodes showed a trend towards increased reversibility for ascorbic acid. Carboxylic acid-CNT modified disk electrodes were then tested for detection of serotonin in the ventral nerve cord of a Drosophila melanogaster larva, and the increase in sensitivity was maintained in biological tissue. The functional groups of CNTs therefore modulate the electrochemical properties, and the increase in sensitivity from CNT modification facilitates measurements in biological samples.     

Fabrication and study of supercapacitor electrodes based on oxygen plasma functionalized carbon nanotube fibers

Dry-spun Carbon Nanotube(CNT) fibers were surface-modified by atmospheric pressure oxygen plasma functionalization using a well controlled and continuous process. The fibers were characterized by scanning electron microscopy(SEM), Raman spectroscopy, and X-ray Photoelectron Spectroscopy(XPS). It was found from the conducted electrochemical measurements that the functionalized fibers showed a 132.8%increase in specific capacitance compared to non-functionalized fibers. Dye-adsorption test and the obtained Randles-Sevcik plot demonstrated that the oxygen plasma functionalized fibers exhibited increased surface area. It was further established by Brunauer-Emmett-Teller(BET) measurements that the surface area of the CNT fibers was increased from 168.22 m~2/g to 208.01 m~2/g after plasma functionalization. The pore size distribution of the fibers was also altered by this processing. The improved electrochemical data was attributed to enhanced wettability, increased surface area, and the presence of oxygen functional groups, which promoted the capacitance of the fibers. Fiber supercapacitors were fabricated from the oxygen plasma functionalized CNT fiber electrodes using different electrolyte systems. The devices with functionalized electrodes exhibited excellent cyclic stability(93.2% after 4000 cycles), flexibility, bendability, and good energy densities. At 0.5 m A/cm~2, the EMIMBF4 device revealed a specific capacitance, which is 27% and 65% greater than the specific capacitances of devices using EMIMTFSI and H_2 SO_4 electrolytes,respectively. The practiced in this work plasma surface processing can be employed in other applications where fibers, yarns, ribbons, and sheets need to be chemically modified.     

Preparation and physical properties of poly(trimethylene terephthalate)/metallocene isotactic polypropylene conjugated fibers

Poly(trimethylene terephthalate) (PTT) and metallocene isotactic polypropylene (MIPP) polymers were extruded (in the proportions of 75/25, 50/50, 25/75) from two melt twin-screw extruders to prepare three PTT/MIPP conjugated fibers. This study investigated the preparation and physical properties of PTT/MIPP conjugated fibers using gel permeation chromatograph (GPC), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), potentiometer, a rheometer, the density gradient, wide-angle X-ray diffraction (WAXD), extension stress-strain measurement and scanning electron microscope (SEM). Melting behavior of PTT/MIPP polyblended polymers exhibited negative-deviation blends (NDB) and the 50/50 blend of PTT/MIPP showed a minimum value of the melt viscosity. Experimental results of the DSC indicated PTT and MIPP molecules formed immiscible system. The tenacity of PTT/MIPP conjugated fibers decreased initially and then increased as the MIPP content increased. Crystallinities and densities of PTT/MIPP conjugated fibers were the linear relation with the blend ratio. PTT and MIPP polymers were proved to be an incompatible system. On the morphological observation, it was revealed that the blends were in a dispersed phase structure. The pore/fiber morphology of a larger size from 0.5 to 3 μm in diameter was observed after 1,1,1,3,3,3-hexafluoro-2-propanol (PTT was removed)/paraffin oil (MIPP was removed) treatment on the cross-section of PTT/MIPP conjugated fiber. In this paper, PTT micro fibers were produced successfully.     

Flexible supercapacitors based on carbon nanotubes

This review provides an overview of recent progress towards the development of flexible supercapacitors based on macroscopic carbon nanotubes-based electrodes, including one-dimensional (1D) fibers, 2D films, and 3D foams, with a focus on electrode preparation and configuration design as well as their integration with other multifunctional devices.     

Study on morphology of electrospun poly(vinyl alcohol) mats

Submicron poly(vinyl alcohol) (PVA) fiber mats were prepared by electrospinning of aqueous PVA solutions in 6-8% concentration. Fiber morphology was observed under a scanning electron microscope and effects of instrument parameters including electric voltage, tip-target distance, flow rate and solution parameters such as concentration on the morphology of electrospun PVA fibers were evaluated. Results showed that, when PVA with higher degree of hydrolysis (DH) of 98% was used, tip-target distance exhibited no significant effect on the fiber morphology, however the morphological structure can be slightly changed by changing the solution flow rate. At high voltages above 10 kV, electrospun PVA fibers exhibited a broad diameter distribution. With increasing solution concentration, the morphology was changed from beaded fiber to uniform fiber and the average fiber diameter could be increased from 87 ± 14 nm to 246 ± 50 nm. It was also found that additions of sodium chloride and ethanol had significant effects on the fiber diameter and the morphology of electrospun PVA fibers because of the different solution conductivity, surface tension and viscosity. When the DH value of PVA was increased from 80% to 99%, the morphology electrospun PVA fibers was changed from ribbon-like fibers to uniform fibers and then to beaded fibers. The addition of aspirin and bovine serum albumin also resulted in the appearance of beads.     

碳纳米管在聚对苯二甲酸丙二酯/乙烯-醋酸乙烯酯共聚物不相容共混体系中的选择性分散

采用熔融共混法制备了碳纳米管(CNT)填充改性的聚对苯二甲酸丙二酯(PTT)/乙烯-醋酸乙烯酯共聚物(EVA)三元复合材料.通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)、接触角测量仪、旋转流变仪等研究了该复合材料中碳纳米管的分布、不相容的相形态以及流变和力学性能.研究结果表明,与EVA相比,PTT组分具有较低...