Effect of silica content on thermal stability of fumed silica/epoxy composites

Composites of a fumed silica industrial residue and an epoxy resin were prepared and their thermal stability and thermal degradation behaviour were studied by TGA in air. Classical thermal stability parameters, based on the initial decomposition temperature (IDT), temperature of maximum rate of mass loss (T_max) and integral procedure decomposition temperature (IPDT) were calculated before and after subtraction of the filler mass from the TGA curves. Without filler mass subtraction, the thermal stability of the epoxy resin seems to be improved and the mass loss rate was reduced by the addition of fumed silica. Nevertheless, after subtraction of the filler mass, the thermal degradation behaviour of the resin was only slightly affected by the silica content. A possible negative effect of the silica content on the cure was also found.     

Surface electric and titration behaviour of fumed oxides

Adsorption of Pb(II), Sr(II), and Cs(I) on fumed silica, alumina, titania, silica/titania (ST), silica/alumina (SA), and alumina/silica/titania (AST) reveals that mixed oxides containing titania have a greater adsorptive capability in respect to metal cations than individual and SA oxides. Pyrocarbon deposits on fumed oxides enhance the adsorption of metal ions. Calculations of electrophoretic potential (ζ) with consideration for the porosity of aggregates of primary particles of AST show a significant influence of surface alumina (at pH<8) and titania and silica (at pH>8) on the ζ values. The effective diameter of particles (D_ef) of fumed oxides in aqueous media depends on pH for AST stronger than for ST (between isoelectric points (IEPs) of titania and alumina). A significant difference in the pH values of IEP and point of zero charge is observed for AST samples. A pyrocarbon influence on the ζ potential depends on the type of oxide matrix, since ζ increases for certain samples but for others it decreases. These changes depend nonlinearly on pH as well as the secondary particle size distributions (SPSDs) and D_ef.     

Modification of fumed silica surface with different sulfonamides via a postsynthesis method and their application as antibacterial agents

The surface of nanosized fumed silica (FSi) was modified with different amine groups by the use of silylating agents. The obtained propylamine, propylpiperazine, and propyl-p-phenylenediamine–modified FSi were treated with different sulfonyl chlorides to gain sulfonamide-modified FSi compounds. These compounds were characterized by various techniques including Fourier transform infrared spectroscopy, thermogravimetric analysis, differential thermal analysis, scanning electron microscopy, and energy-dispersive X-ray spectroscopy (EDX), confirming the grafted sulfonamides on the FSi surface. Sulfonamide-modified surfaces are efficient catalysts for the Michael addition-based syntheses and coupling reactions. Furthermore, the antibacterial tests showed that these modified FSi compounds have antibacterial activities and thus are useful materials for preparing antibacterial silicone-based compounds such as silicone glue and oil.     

Epinephrine‐modified methacrylate monolithic column with fumed silica nanoparticle for pressurized capillary electrochromatography

Via the ring‐opening reaction of epoxy groups with epinephrine, a novel epinephrine functionalized polymethacrylate monolith with fumed silica nanoparticles has been fabricated for pressurized capillary electrochromatography. The preparation of epinephrine‐modified monoliths has been optimized. In addition, morphology, electroosmotic flow, separation mechanism and column performance have been studied. The internal structure of the monolithic stationary phase was more uniform and the column efficiency increased after the incorporation of nanoparticles. With this column, satisfactory separation capability of aromatic compounds and alkaloids has been achieved and the column efficiency for naphthalene reached 138 696 plates/m. As for the real sample, 3 alkaloids were separated in Huanglian Shangqing capsules, a Chinese traditional medicine.     

Interactions between bioactive ferulic acid and fumed silica by UV–vis spectroscopy, FT-IR, TPD MS investigation and quantum chemical methods

The interactions of bioactive ferulic acid with fumed silica were studied by UV/vis spectroscopy, FT-IR, TPD MS techniques and quantum chemical methods. It was found that surface complexes may form through phenol or carboxyl group of ferulic acid depending on its coverage value. The structure of surface complexes and mechanisms of the ferulic acid chemosorption on the silica surface are discussed. The kinetic parameters of the chemical reactions on silica surface are calculated. The mechanisms of thermal transformations of the ferulic chemosorbed surface complexes are proposed.     

Function and performance of silicone copolymer (VII). Dispersing ability of hydrophile-grafted acrylic copolymers and the corresponding siloxane copolymers to fumed silica. The effect of pH

Acrylic copolymers and the corresponding siloxane copolymers grafted with cationic and nonionic hydrophiles were used as dispersants to disperse fumed silica in an aqueous solution at different pH values. The dispersing ability was evaluated by viscosity and scanning electron microscopy (SEM) methods. The results showed that the dispersing abilities are functions of the dispersant concentrations and of the pH of the system. By comparing the results of SEM and viscosity methods, it can be concluded that, under comparable conditions, a suspension with a lower viscosity is more homogenously dispersed. It was also found that at pH 2 only CHE and SHE and that at pH 7 only CHE, SHE, and SQHE showed better dispersing ability. At pH 10.5, all the dispersants in this study except CQDEA resulted in a slurry of very low viscosity of 10–20 cP with 15 wt% of silica. Basically, nonionic dispersants CHE and SHE exhibit excellent dispersing ability at different pH values. Received: 16 March 2001 Accepted: 28 June 2001     

Synthesis and characterization of surface-aminated polypyrrole–silica nanocomposites

 Two synthetic routes to surface-aminated polypyrrole–silica nanocomposite particles have been investigated. Route 1 involved the initial synthesis of homopolypyrrole – silica particles as described previously, followed by surface amination using 3-aminopropyltriethoxy-silane. In Route 2 aminated polypyrrole–silica particles were synthesized directly by copolymerising an N-substituted aminopyrrole comonomer with pyrrole in the presence of an ultrafine silica sol. Both types of aminated particles were characterized in terms of their particle size and morphology, long-term colloid stability and degree of amination using transmission electron microscopy, disc centrifuge photosedimentometry and zeta potential measurements, respectively. Received: 19 May 1998 Accepted: 15 June 1998     

Preparation and characterization of polypropylene/mesoporous silica nanocomposites with confined polypropylene

Polypropylene (PP)/Ti-MCM-41 nanocomposites were prepared by isospecific propylene polymerization with Ti-MCM-41/Al(i-C₄H₉)₃ catalyst. The cross polarization/magic angle spinning (CP/MAS) ¹³C NMR spectrum of the composite was similar to that of the conventional isotactic PP, and the decrease in the pore volume of Ti-MCM-41 in the nanocomposites, as measured by N₂ adsorption, was consistent with the value calculated from the weight loss in the thermogravimetric analysis (TGA) curve; both these facts attest to propylene polymerization within the mesopores of Ti-MCM-41. Alkali treatment followed by extraction with o-dichlorobenzene allows us to extract the confined PP out of the Ti-MCM-41 mesopores. Although the PP/Ti-MCM-41 nanocomposites do not exhibit a crystalline melting point, the same PP when extracted from the mesopores showed a clear melting point at 154.7 °C; this indicates that the crystallization of PP confined in mesopores is strongly hindered. For the PP polymerized within the confinement, the molecular weight (M_w) and molecular weight distribution (M_w/M_n) were 84,000 and 4.3, respectively; these values were considerably smaller than those of the PP polymerized concurrently outside the Ti-MCM-41 mesopores (M_w = 200,000–450,000, M_w/M_n = 40–75). Therefore, the confinement also has a marked effect on the molecular weight of the PP. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3324–3332, 2003     

Preparation and characterization of polyimide/mesoporous silica hybrid nanocomposites based on water-soluble poly(amic acid) ammonium salt

Recently, mesoporous silica was blended with polyimide to develop low dielectric constant (k) materials with improving mechanical and thermal properties of polyimide by utilizing both the nanoporous structure and silica framework. However, even the use of mesoporous silica did not show a significant decrease of k due to the phase segregation in between polyimide and the mesoporous silica materials. In this work, we attempted to prepare polyimide/mesoporous silica hybrid nanocomposites having relatively good phase mixing behavior by utilizing polyimide synthesized from a water soluble poly(amic acid) ammonium salt, which lead to low k up to 2.45. The thermal properties of polyimide were improved by adding mesoporous silicas. For this work, we have fabricated mesoporous silicas through surfactant-templated condensation of tetraethyl orthosilicate (TEOS). Pyromellitic dianhydride (PMDA)-4,4′-oxydianiline (ODA) polyimide was prepared from poly(amic acid) ammonium salt, which had been obtained by incorporating triethylamine (TEA) into PMDA-ODA poly(amic acid) in dimethylacetamide (DMAc), followed by thermal imidization.     

Development of hybrid nanocomposites based on PLLA and low-field NMR characterization

Hybrid nanocomposite based on poly(L-lactic acid) (PLLA) employing silica (A200) and organophilic silica (R972), natural clay (NT-25) and two types of organoclay (S4 and S7) were prepared by the solution casting method. Each nanoparticle type was incorporated at two ratios (3 and 5%) relative to the polymer matrix. The nanocomposites formed were evaluated by X-ray, thermal resistance and molecular dynamic analysis, using proton spin-lattice relaxation time. The results showed that each nanoparticle type acted independently of the polymer/nanoparticle ratio in the new material. Both silica types promoted an increase in rigidity, due to the strong intermolecular forces. The natural clay did not cause any significant change in the molecular mobility of the nanocomposites, probably due to the non-affinity of the chemical structure. Therefore, both organoclays were better dispersed in the polymeric matrix, allowing good intermolecular interaction and, consequently, exfoliated and intercalated nanocomposites were formed.     

Thermooxidative degradation of LDPE nanocomposites: Effect of surface treatments of fumed silica and boehmite alumina

Fumed silica (FS) and synthetic boehmite alumina (BA) nanofillers with and without surface treatments were incorporated in 5 wt. % in low density polyethylene (LDPE) through melt blending. FS was treated using hexadecyl silane, whereas BA using octyl silane and alkylbenzene sulfonic acid. The related nanocomposites were subjected to pyrolysis gas chromatography-mass spectrometry (Py-GC-MS) and thermogravimetric analysis (TGA) under isothermal and dynamic conditions, respectively. Py-GC-MS results proved that the thermal degradation mechanism did not change in the presence of the nanofillers. The latter suppressed the formation of high molecular weight hydrocarbons and affected the relative amounts of diene/alkene/alkane fragments for each hydrocarbon fraction.     

Preparation and characterization of PE and PE-g-MAH/montmorillonite nanocomposites

Polyethylene (PE) was chemically modified with grafting maleic anhydride (MAH) monomer on its backbone at first. Then the melt-direct intercalation method was employed to prepare two kinds of nanocomposites, polyethylene (PE)/organic montmorillonite (Org-MMT) and maleic anhydride grafted polyethylene (PE-g-MAH)/Org-MMT nanocomposites. X-ray diffractometery (XRD) was used to investigate the intercalation effect and transmission electron microscopy (TEM) to observe the dispersion of Org-MMT interlayers in matrixes. The results show that an intercalated structure would be acquired on mixing the PE and Org-MMT; and an almost exfoliated system would be obtained by mixing the PE-g-MAH and Org-MMT. Moreover, further measurements via thermogravimetric (TGA) and differential scanning calorimetry (DSC) showed that both of the nanocomposites had a higher thermal decomposition temperature and a higher crystallization temperature when compared to the original matrix. At the same time, the thermal and crystal properties for the PE-g-MAH prepared in this experiment are also discussed.     

Synergistic effect between POSS and fumed silica on thermal stabilities and mechanical properties of room temperature vulcanized (RTV) silicone rubbers

In this paper, both divinyl-hexa[(trimethoxysilyl)ethyl]-POSS (DVPS) and fumed silica were firstly introduced into polydimethylsiloxane (PDMS) system using as the cross-linker and the reinforcing filler respectively. And a series of novel RTV silicone rubbers synergistically enhanced by DVPS and fumed silica were prepared. The cross-linked networks in the novel RTV silicone rubbers have been studied by attenuated total reflection infrared spectroscopy, and the dispersions of POSS and fumed silica in these novel RTV silicone rubbers have been observed by means of scanning electron microscope (SEM). And thermal stabilities, thermo-oxidative stabilities and mechanical properties of these novel RTV silicone rubbers were studied by means of thermal gravimetric analysis and universal tensile testing machine, respectively. From the obtained results, it was found that synergistic effect between POSS-rich areas and fumed silica on thermal stability and mechanical property of RTV silicone rubber indeed existed. And the experimental results also exhibited that the thermal stabilities and mechanical properties of the novel RTV silicone rubbers were far better than those of the reference materials (DVPR and MTFR). The striking enhancements in thermal properties and improvements on mechanical properties of novel RTV silicone rubbers were likely attributed to the synergistic effect between POSS-rich domains and fumed silica. Meanwhile, it was found that the mechanical properties of RTV silicone rubbers prepared with a given amount of POSS cross-linker were enhanced with the increment of the loading amount of fumed silica.     

Interfacial phenomena in starch/fumed silica at varied hydration levels

Hydrated powders of non-gelatinised starch and hydrogels of gelatinised starch alone or with addition of modified nanosilica (with grafted aminopropylmethylsilyl groups substituting one-third of surface silanols) were studied using broadband dielectric relaxation spectroscopy (DRS), thermally stimulated depolarisation current (TSDC) method and ¹H NMR spectroscopy with layer-by-layer freezing-out of bulk and interfacial waters. The ¹H NMR and TSDC techniques with the use of Gibbs–Thomson relation for the freezing point depression allow us to calculate: (i) the thermodynamic parameters of interfacial water weakly and strongly bound to polymer molecules and nanoparticles; (ii) size distributions of pores filled by structured water; (iii) surface area and volume of micro-, meso- and macropores. The DRS and TSDC results for hydrogels and hydrated powders with starch/modified fumed silica show that the β- and γ-relaxations of starch are strongly affected by water and functionalised silica nanoparticles which slow down both low- and high-frequency and low- and high-temperature relaxations.     

Preparation and characterization of waterborne polyurethane/attapulgite nanocomposites

In this paper, waterbrone polyurethane (WPU)/attapulgite (AT) nanocomposites have been prepared by direct emulsion blending. The WPU was synthesized from poly(tetramethylene glycol), 4,4-diphenylmethane diisocyanate, dimethylol butanic acid, and neutralized by triethylamine. SEM examination of fractured surfaces showed that AT particles were irregularly dispersed in the WPU matrix. FTIR analysis suggested no major chemical structural changed in the presence of a small amount of AT. DMA results showed that the storage modulus of WPU/AT nanocomposites was increased and the glass transition temperatures of both soft and hard segments shifted to higher temperature compared to the pristine WPU. Thermal resistance of the samples measured by TGA was improved with the addition of AT. The mechanical properties of the nanocomposites, examined by tensile tests, showed higher tensile strength and elongation at break than that of the pristine WPU.     

In situ polymerized poly(butylene succinate)/silica nanocomposites: Physical properties and biodegradation

A series of poly(butylene succinate)/silica (PBS/silica) nanocomposites were prepared by in situ polymerization. Solid-state ²⁹Si NMR and FTIR analysis indicated that silanol-bonded carbonyl groups are established within PBS/silica nanocomposite materials. Rheological effects inherent to the silica filler were evaluated by melt rheological analysis as a function of shear force in the molten state. Despite high shear force, PBS/silica nanocomposites maintained a relatively high melt viscosity, attributable to a network structure resulting from covalent bonding between silica and the polymer chain. Nanocomposite material containing 3.5 wt% silica exhibited greatly improved mechanical properties. The tensile strength at break and elongation were ca. 38.6 MPa and 515%, while those of the parent PBS were 26.3 MPa and 96%, respectively. PBS/silica nanocomposites showed composition dependency on biodegradation ascribable to reduced crystallinity and preferential microbial attack.     

Synthesis and characterization of poly1-hexene/silica nanocomposites

SiO₂ nano particles, with particle size of 12 nm, were first modified by substituting surface OH groups with O-hexyl moiety. Then, poly1-hexene/modified-SiO₂ composites with various nano-SiO₂ weight fractions were prepared by three different methods: in situ, solution, and melt methods and designated as PH-SiO₂/Insitu, PH-SiO₂/Sol and PH-SiO₂/Melt, respectively. PH-SiO₂/Insitu samples showed highly uniform particle dispersion up to 30 wt. % of silica while in PH-SiO₂/Sol and PH-SiO₂/Melt samples agglomeration of the silica nanoparticles occurred for filler contents ≥5 wt. % (i.e. 5, 10, 20 and 30 wt%). In the synthesized composites, the storage modulus significantly increased as high as 20.7 times when compared with neat poly1-hexene. Maximum decomposition temperature (T_max) and char yield at 600 °C increased with increasing silica level. Rheological results showed that G^ʹ> G^ʺ over the frequency range, illustrating the elastic behavior of the composite samples. In fact, samples showed the characteristic of a non-Newtonian fluid with a strong shear thinning effect in which η* increased with increasing filler weight fraction. From the results, it can be expected that modified silica could replace silica nanoparticles in polyolefin nanocomposite reinforcement.     

In situ prepared PBSu/SiO2 nanocomposites. Study of thermal degradation mechanism

A series of nanocomposites consisted of poly(butylene succinate) (PBSu) and fumed silica nanoparticles (SiO₂) were prepared using the in situ polymerization technique. The amount of SiO₂ used directly affected the final molecular weight of the prepared polyesters. At a low SiO₂ content (0.5 wt.%) the molecular weight obtained was higher compared to neat PBSu, however at higher concentrations this was gradually reduced. The melting point of the matrix remained unaffected by the addition of the nanoparticles, in contrast to the crystallinity, which was dramatically reduced at higher SiO₂ contents. This was mainly due to the extended branching and cross-linking reactions that took place between the carboxylic end groups of PBSu and the surface silanols of the nanoparticles. Thermal degradation of the PBSu/SiO₂ nanocomposites was studied by determining theirs mass loss during heating. From the variations of the activation energies, calculated from the thermogravimetric curves, it was clear that nanocomposites containing 1 wt.% SiO₂ content had a higher activation energy compared to pure PBSu, indicating that the addition of the nanoparticles could slightly increase the thermal stability of the matrix. However, in PBSu/SiO₂ nanocomposite containing 5 wt.% SiO₂ the activation energy was smaller. This phenomenon should be attributed to the existence of extended branched and cross-linked macromolecules, which reduce the thermal stability of PBSu, rather than to the addition of fumed silica nanoparticles.     

Fumed silica for the direct determination of lead in urine by differential-pulse anodic stripping voltammetry

The use of fumed silica for the direct determination of lead in urine by differential-pulse anodic stripping voltammetry was investigated. Fumed silica, added to urine prior to the nitrogen purge step, completely removed sorption interferences by urinary organic constituents. Values for lead in urine from eight unexposed individuals were 3 ± 2 μg l^?1 or 3 ± 2 μg g^?1 creatinine. This method is a fast, simple and effective means for the accurate determination of lead in undiluted urine without pretreatment.     

Effect of sepiolite on the biodegradation of poly(lactic acid) and polycaprolactone

PLA and PCL nanocomposites prepared by adding 5 wt% of a sepiolite (SEPS9) were degraded in compost, leading to effective degradation for all samples.PLA and PLA/SEPS9 seem to be mainly degraded by a bulk mechanism, showing a significant level of polymer degradation, however the presence of SEPS9 particles partially delays the degradation probably due to a preventing effect of these particles on polymer chain mobility and/or PLA/enzymes miscibility. PCL and PCL/SEPS9 showed a preferential surface mechanism of degradation; and in contrast to PLA, sepiolite does not present a considerable barrier effect on the degradation of PCL.