In situ polymerization of methyl methacrylate/multi-walled carbon nanotube composites using cationic stearyl methacrylate copolymers as dispersants

Novel water-soluble amphiphilic copolymers (poly[(stearyl methacrylate)-stat-([2-(methacryloyloxy)ethyl] trimethyl ammonium iodide)]) for dispersing multi-walled carbon nanotubes (MWCNTs) were used to carry out in situ methyl methacrylate (MMA) polymerization. The morphology of the poly(methyl methacrylate)/MWCNT composites and the dispersion of the MWCNTs were analyzed by transmission electron microscopy. The dispersion of multi-walled carbon nanotubes in the composites was excellent for cationic SMA (stearyl methacrylate) copolymers, even at high MWCNT loading (6.0 wt.%). The mechanical properties and electrical and thermal conductivities of the composites were also analyzed. Mechanical properties were improved by MWCNTs; the strain at break values remained stable up to 6.0 wt.% MWCNT loading. Both electrical and thermal conductivities were improved by the addition of MWCNTs.     

Rheological and electrical properties of polypropylene/MWCNT composites prepared with MWCNT masterbatch chips

Melt compounded PP/MWCNT (polypropylene/multi-walled carbon nanotube) composites were prepared by diluting highly concentrated masterbatch chips. Maleic anhydride grafted polypropylene (PP-g-MAH) was used as a compatibilizer to promote dispersion and interaction of MWCNTs. Rheological properties were investigated with respect to the MWCNT and compatibilizer loadings, and related to morphological and electrical properties. As the MWCNT loading was increased, shear viscosity and yield stress were increased at low shear rate region because of increased interaction between MWCNT particles. When the MWCNT loading was low, MWCNT dispersion was improved by the PP-g-MAH compatibilizer because MWCNTs were wetted sufficiently due to the presence of the compatibilizer. However, rheological and electrical properties of highly concentrated MWCNT composites with the compatibilizer were not improved compared with PP/MWCNT composites without the compatibilizer because the compatibilizer did not provide sufficient wrapping of MWCNT particles. Electrical and morphological properties of PP/MWCNT composites were correlated with the rheological properties in steady and dynamic oscillatory shear flows.     

Significant enhancement of electrical and thermal conductivities of polyethylene carbon nanotube composites by the addition of a low amount of silver nanoparticles

Electrically and thermally conductive high‐density polyethylene composites filled with hybrid fillers, multiwall carbon nanotubes (MWCNTs) and silver nanoparticles (Ag‐NPs), have been prepared in the melt state. The investigation of their electrical and thermal conductivities while comparing with high‐density polyethylene/MWCNT binary composites shows that the addition of only 3 vol% of Ag‐NPs does not reduce the electrical percolation threshold (P_c) that remains as low as 0.40 vol% of MWCNTs but leads to an increase in the maximum dc electrical conductivity of PE/MWCNT composites by two orders of magnitudes. Moreover, the association of both Ag‐NPs and carbon nanotube particles improved our composite's thermal conductivity. Copyright © 2014 John Wiley & Sons, Ltd.     

Effect of dispersion and selective localization of carbon nanotubes on rheology and electrical conductivity of polyamide 6 (PA6), Polypropylene (PP), and PA6/PP nanocomposites

Nanocomposites were prepared by adding 1–3 vol % multiwalled carbon nanotubes (MWCNTs) to polyamide 6 (PA6), polypropylene (PP), and their co‐continuous blends of 60/40 and 50/50 volume compositions. Because of the good interaction and interfacial adhesion to the PA6, nanotubes were disentangled and distributed evenly through nanocomposites containing PA6. In contrast, lack of active interactions between the matrix and the CNTs resulted in poor tube dispersion in PP. These observations were then verified by studying the rheology and electrical conductivity of their respective nanocomposites. Absence of percolated CNT clusters and possible wrapping of the tubes by PA6 resulted in low electrical conductivity of PA6/CNT nanocomposites. On the other hand, despite the weak dispersion of the tubes, electrical conductivities of PP/CNT nanocomposites were much higher than all other counterparts. This could be the result of good three‐dimensional distribution of the agglomerated bundles and secondary aggregation of tubes in PP. Adding CNTs to blends of PA6/PP (60/40 and 50/50) resulted in almost full localization of carbon nanotubes in PA6, leading to their higher effective concentration. At the same CNT loadings, the blend nanocomposites had three to seven orders of magnitude higher electrical conductivity than pure PA6. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 368–378     

New melt mixing polyethylene multiwalled carbon nanotube nanocomposites with very low electrical percolation threshold

The present work focuses on the study of the electrical properties of high‐density polyethylene (HDPE)/multiwalled carbon nanotube (MWCNT) nanocomposites. The samples were produced by melt mixing by diluting a masterbatch of HDPE/MWCNT using two types of mini‐extruders in order to see the influence of the shear processing on the electrical properties. The dielectric relaxation spectroscopy was used for the investigation of the electrical properties in the studied samples. The composites dc conductivity (σ_dc) follows the scaling low derivate from the percolation theory of the form σ_dc ~ (p ? p_c)^t. A low electrical percolation (p_c ≈ 0.3 ? 0.4 vol. %) was found in both cases. The critical exponent t had a value very close to the theoretical one for a percolation network in three dimensions (t ≈ 2). The analysis of the morphology of the nanocomposites showed a good and homogeneous dispersion of the fillers in the PE matrix. The effect of the incorporation of MWCNTs on the dynamic mechanical and thermal behaviors was also presented. The MWCNTs have improved the mechanical properties of the polyethylene matrix and increased the crystallization temperatures. Copyright © 2013 John Wiley & Sons, Ltd.     

Preparation and Properties of Pyrene-Modified Multi- Walled Carbon Nanotube/Epoxy Resin Nanocomposites

Nanocomposites of multi-walled carbon nanotube (MWCNT)/bis-phenol A type epoxy resin were prepared and physical properties of the nanocomposites were investigated. For the fine dispersion of MWCNT in the epoxy resin, MWCNT was modified with pyrene butyric acid (PBA) in the supercritical carbon dioxide (CO₂). The physical adsorption of PBA on the surface of MWCNTs was studied with a thermogravimetric analyzer and a transmission electron microscopy. The electrical surface resistivities of the nanocomposites showed threshold decreases due to percolations above the critical concentration of the MWCNT. The resistivities showed maximum depending on the concentration and the modification of the surface of the MWCNT with PBA. It is postulated that the dispersion of the MWCNT in epoxy resins resulted in dispersion systems which exhibit rheological properties similar to lyotropic liquid crystalline polymers. The surface resistivities of the MWCNT/epoxy systems reflected the morphological characteristics of the systems which also determined rheological properties of the systems.     

Multiwalled carbon nanotube promotes crystallisation while preserving co-continuous phase morphology of polycarbonate/polypropylene blend

The influence of multiwalled carbon nanotubes (MWCNTs) on phase morphology, lamellar structure, thermal stability, melting behaviour and isothermal crystallisation kinetics of polycarbonate/polypropylene (PC/PP) blend nanocomposites has been investigated. Both neat blends and PC/PP (60/40)/MWCNT nanocomposites were prepared by melt mixing method. Morphological analyses were performed by high-resolution X-ray micro-computed tomography and scanning electron microscopy. The co-continuous morphology of the blend was retained irrespective of MWCNT loading. In addition, a substantial refinement in the co-continuous structure was observed. Wide angle and small angle X-ray scattering studies were used to analyse the structural properties of the blend nanocomposites. The addition of MWCNT increases the long period of polypropylene. The influence of addition of MWCNT on the crystallisation temperature and equilibrium melting temperature (Tm°) of polypropylene was followed. The MWCNTs promote crystallisation rate of polypropylene in the blend nanocomposites.     

Core–shell functionalized MWCNT/poly(m‐aminophenol) nanocomposite with large dielectric permittivity and low dielectric loss

Core–shell carboxyl‐functionalized multiwall carbon nanotube (c‐MWCNT)/poly(m‐aminophenol) (PmAP) nanocomposite were prepared through in‐situ polymerization of m‐aminophenol (m‐AP) in the presence of MWCNTs, and explicated as a dielectric material for electronic applications. The formation of thin PmAP layer on individual c‐MWCNT with excellent molecular level interactions at interfaces was confirmed by morphological and spectroscopic analyses. Here we conducted a comparative study of the dielectric performances of PmAP based nanocomposite films with pristine MWCNTs and c‐MWCNTs as fillers. Compared to PmAP/MWCNT nanocomposites, the PmAP/c‐MWCNT nanocomposites exhibited higher dielectric permittivity and lower dielectric loss. The well dispersed c‐MWCNTs in PmAP/c‐MWCNT nanocomposite produce huge interfacial area together with numerous active polarized centers (crystallographic defects), which in turn intensified the Maxwell‐Wagner‐Sillars (MWS) effect based on excellent molecular level interactions and thus, produce large dielectric permittivity (8810 at 1 kHz). The percolation threshold of PmAP/c‐MWCNT nanocomposites is found lower than that of the PmAP/MWCNT nanocomposites, which could be attributed to homogeneous distribution of c‐MWCNTs and strong c‐MWCNT//PmAP interfacial interactions in the nanocomposites. Copyright © 2016 John Wiley & Sons, Ltd.     

Effects of electrically inert fillers on the properties of poly(<Emphasis Type="Italic">m</Emphasis>-xylene adipamide)/multiwalled carbon nanotube composites

The effects of three types of electrically-inert fillers, calcium carbonate (CaCO₃), talc and glass fiber (GF), on electrical resistivity, crystallization behavior and dynamic mechanical properties of poly(m-xylene adipamide) (MXD6)/multiwalled carbon nanotube (MWCNT) composites are investigated. The electrical resistivity of MXD6/MWCNT composites is significantly reduced with the addition of inert fillers due to the volume-exclusion effect that leads to increased effective concentration of MWCNTs in MXD6 matrix and also due to improved MWCNT dispersion. The crystallization temperature of MXD6 increases with the addition of MWCNTs, indicating that MWCNTs can act as nucleating agent and induce crystallization of MXD6. The incorporation of inert fillers has no further effect on crystallization behavior of MXD6, but significantly improves the storage modulus of MXD6/MWCNT composite, demonstrating that CaCO₃, talc and GF filled MXD6/MWCNT composites are very promising materials with not only improved electrical property but also excellent mechanical properties.     

Comparative study on the properties of poly(trimethylene terephthalate) ‐based nanocomposites containing multi‐walled carbon (MWCNT) and tungsten disulfide (INT‐WS2) nanotubes

Multi‐walled carbon (MWCNT) and tungsten disulfide (INT‐WS₂) nanotubes are materials with excellent mechanical properties, high electrical and thermal conductivity. These special properties make them excellent candidates for high strength and electrically conductive polymer nanocomposite applications. In this work, the possibility of the improvement of mechanical, thermal and electrical properties of poly(trimethylene terephthalate) (PTT) by the introduction of MWCNT and INT‐WS₂ nanotubes was investigated. The PTT nanocomposites with low loading of nanotubes were prepared by in situ polymerization method. Analysis of the nanocomposites' morphology carried out by SEM and TEM has confirmed that well‐dispersed nanotubes in the PTT matrix were obtained at low loading (<0.5 wt%). Thermal and thermo‐oxidative stability of nanocomposites was not affected by the presence of nanotubes in PTT matrix. Loading with INT‐WS₂ up to 0.5 wt% was insufficient to ensure electrical conductivity of PTT nanocomposite films. In the case of nanocomposites filled with MWCNT, it was found that nanotube incorporation leads to increase of electrical conductivity of PTT films by 10 orders of magnitude, approaching a value of 10^?3 S/cm at loading of 0.3 wt%. Tensile properties of amorphous and semicrystalline (annealed samples) nanocomposites were affected by the presence of nanotubes. Moreover, the increase in the brittleness of semicrystalline nanocomposites with the increase in MWCNT loading was observed, while the nanocomposites filled with INT‐WS₂ were less brittle than neat PTT. Copyright © 2016 John Wiley & Sons, Ltd.     

Structural and morphological studies on the deformation behavior of polypropylene/multi‐walled carbon nanotubes nanocomposites prepared through ultrasound‐assisted melt extrusion process

Structural and morphological behavior under stress–strain of polypropylene/multi‐walled carbon nanotubes (PP/MWCNTs) nanocomposites prepared through ultrasound‐assisted melt extrusion process was studied by means of optical microscopy, scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, small angle X‐ray scattering (SAXS), and wide angle X‐ray scattering (WAXS). A high ductile behavior was observed in the PP/MWCNT nanocomposites with low concentration of MWCNTs. This was related to an energy‐dissipating mechanism, achieved by the formation of an ordered PP‐CNTs interphase zone and crystal oriented structure in the undeformed samples. Different strain‐induced‐phase transformations were observed by ex situ SAXS/WAXS, characterizing the different stages of structure development during the deformation of PP and PP/MWCNTs nanocomposites. The high concentration of CNTs reduced the strain behavior of PP due to the agglomeration of nanoparticles. A structural pathway relating the deformation‐induced phase transitions and the dissipation energy mechanism in the PP/MWCNTs nanocomposites at low concentration of nanoparticles was proposed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 475–491     

Electrically conductive transparent papers using multiwalled carbon nanotubes

We describe a novel class of electrically conductive transparent materials based on multiwalled carbon nanotubes (MWCNTs). Transparent nanocomposites were fabricated by incorporating an aqueous silk fibroin solution into bacterial cellulose membranes. The transparent nanocomposites had a high transmittance in the visible and infrared regions, regardless of the bacterial cellulose fiber content, due to the nanosize effect of the bacterial cellulose nanofibrils. This phenomenon allowed the preparation of a novel electrically conductive transparent paper. The high dispersity of the MWCNTs was realized by utilizing a bacterial cellulose membrane as a template to deposit them uniformly, thereby achieving electrically conductive transparent papers with outstanding optical transparency. The light transmittance and electrical conductivity varied according to the concentration of the MWCNT dispersion. Good optimal transparency and electrical properties were obtained with a light transmittance of 70.3% at 550 nm and electrical conductivity of 2.1 × 10^?3 S/cm when the electrically conductive transparent paper was fabricated from a 0.02 wt % aqueous MWCNT dispersion. In addition, the electrically conductive transparent papers showed remarkable flexibility without any loss of their initial properties. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1235–1242, 2008     

The mechanical and electrical properties of carbon nanotube‐grafted polyimide nanocomposites

Polyimide (PI)‐based nanocomposites containing aminophenyl functionalized multiwalled carbon nanotubes (AP‐MWCNTs) obtained through a diazonium salt reaction was successfully prepared by in situ polymerization. PI composites with different loadings of AP‐MWCNTs were fabricated by the thermal conversion of poly(amic acid) (PAA)/AP‐MWCNTs. The mechanical and electrical properties of the AP‐MWCNTs/PI composites were improved compared with those of pure PI due to the homogeneous dispersion of AP‐MWCNTs and the strong interfacial covalent bonds between AP‐MWNTs and the PI matrix. The conductivity of AP‐MWNTs/PI composites (5:95 w/w) was 9.32 × 10^?1 S/cm which was about 10¹⁵ times higher than that of Pure PI. The tensile strength and tensile modules of the AP‐MWCNTs/PI composites with 0.5 wt % of AP‐MWCNTs were increased by about 77% (316.9 ± 10.5 MPa) and 25% (8.30 ± 1.10 GPa) compared to those of pure PI, respectively. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 960–966     

Electrical conductivity of PUR/MWCNT nanocomposites in the molten state, during crystallization and in the solid state

The electrical conductivity of a nanocomposite constituted of multiwalled carbon nanotubes (MWCNT) dispersed in a semicrystalline polyurethane matrix, is investigated during cooling from the melt to the solid state. The same percolation threshold, ?_c = 0.85 wt.%, is obtained in the molten and in the solid state, although the exponent t of the percolation equation is significantly higher in the solid state. A remarkable increase of the conductivity during crystallization is observed for nanocomposites of MWCNT content above ?_c, but for contents below ?_c the conductivity decreases. Combined conductivity and PVT results, lead us to discard the hypothesis of an increase of the density of the conductive network (associated with volume shrinkage) as being the cause of the conductivity enhancement during crystallization. Instead, the analysis of the parameters of the percolation equation for the molten and the solid state, suggests a transition from a less effective conductive network to a more performing three dimensional network.     

Influence of talc with different particle sizes in melt‐mixed LLDPE/MWCNT composites

Linear low‐density polyethylene (LLDPE) was melt‐mixed with multiwalled carbon nanotubes (MWCNTs) and varying amounts of three different kinds of talc (phyllo silicate), each with a different particle size distribution, to examine the effect of these filler combinations with regards to the electrical percolation behavior. The state of the filler dispersion was assessed using transmission light microscopy and electron microscopy. The use of talc as a second filler during the melt mixing of LLDPE/MWCNT composites resulted in an improvement in the dispersion of the MWCNTs and a decrease of the electrical percolation threshold. Talc with lower particle sizes showed a more pronounced effect than talc with larger particle sizes. However, the improvement in dispersion was not reflected in the mechanical properties. Modulus and stress values increase with both, MWCNT and talc addition, but not in a synergistic manner. The crystallization behavior of the composites was studied by differential scanning calorimetry to determine its potential influence on the electrical percolation threshold. It was found that the crystallinity of the matrix increased slightly with the addition of talc but no further increments were observed with the incorporation of the MWCNTs. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1680–1691     

Competition between supernucleation and plasticization in the crystallization and rheological behavior of PCL/CNT‐based nanocomposites and nanohybrids

PCL was blended with pristine multiwalled carbon nanotubes (MWCNT) and with a nanohybrid obtained from the same MWCNT but grafted with low molecular weight PCL, employing concentrations of 0.25 to 5 wt % of MWCNT and MWCNT‐g‐PCL. Excellent CNT dispersion was found in all samples leading to supernucleation of both nanofiller types. Nanohybrids with 1 wt % or less MWCNTs crystallize faster than nanocomposites (due to supernucleation), while the trend eventually reverses at higher nanotubes content (because of plasticization). Rheological results show that yield‐like behavior develops in both nanocomposites, even for the minimum content of carbon nanotubes. In addition, the MWCNT‐g‐PCL family, when compared with the neat polymer, exhibits lower values of viscosity and modulus in oscillatory shear, and higher compliance in creep. These rheological differences are discussed in terms of the plasticization effect caused by the existence of low molecular weight free and grafted PCL chains in the nanohybrids. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1310–1325     

Properties of matrix-grafted multi-walled carbon nanotube/poly(methyl methacrylate) nanocomposites synthesized by in situ reversible addition-fragmentation chain transfer polymerization

Multi-walled carbon nanotubes (MWCNT)/poly(methyl methacrylate) (PMMA) nanocomposites were synthesized by the in situ reversible addition-fragmentation chain transfer (RAFT) polymerization of methyl methacrylate (MMA) in the presence of MWCNTs, at which the bulk polymer was grafted onto the surface of nanotubes through the ??grafting through?? strategy. For this purpose, MWCNTs were formerly functionalized with polymerizable MMA groups. MMA and PMMA-grafted MWCNTs were characterized by Fourier-transform infrared spectroscopy, Raman, X-ray photoelectron spectroscopy, transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). Dissolution of nanotubes was examined in chloroform solvent and studied by UV?Cvis spectroscopy. Thermogravimetric and degradation behavior of prepared nanocomposites was investigated by TGA. MWCNTs had a noticeable boosting effect on the thermal stability of nanocomposites. TGA thermograms showed a two-step weight loss pattern for the degradation of MWCNT-PMMA/PMMA nanocomposites which is contrast with neat PMMA. Introduction of MWCNTs also improved the dynamic mechanical behavior and electrical conductivity of nanocomposites. TEM micrograph of nanocomposite revealed that the applied methods for functionalization of nanotubes and in situ synthesis of nanocomposites were comparatively successful in dispersing the MWCNTs in PMMA matrix.     

Thermal and electrical properties of poly(l-lactide)-graft-multiwalled carbon nanotube composites

The dispersion of the nanometer-sized carbon nanotubes in a polymer matrix leads to a marked improvement in the properties of the polymer. This approach can also be applied to biodegradable synthetic aliphatic polyesters such as poly(l-lactide) (PLLA), which has received a great deal of attention due to environmental concerns. In this study, PLLA was melt compounded with multiwalled carbon nanotubes (MWCNTs). A high degree of dispersion of the MWCNTs in the composites was obtained by grafting PLLA onto the MWCNTs (PLLA-g-MWCNTs). After oxidizing the MWCNTs by treating them with strong acids, they were reacted with l-lactide to produce the PLLA-g-MWCNTs. The morphology of the composite was observed with scanning electron microscopy. The mechanical properties of the PLLA/PLLA-g-MWCNT composite were higher than those of the PLLA/MWCNT composite. The thermal stability of the composites was studied using thermogravimetric analysis and their activation energy during thermal degradation was determined using the Kissinger and Flynn-Wall-Ozawa methods. The activation energy of PLLA/PLLA-g-MWCNT was higher than that of PLLA/MWCNT, which indicates that the composite made with the PLLA-g-MWCNTs was more thermally stable than the composite made with the MWCNTs.     

β成核剂修饰多壁碳纳米管增强聚丙烯纳米复合材料的分散及结晶行为

利用非共价键改性方法,用芳香二羧酸酰胺类的β成核剂(β-NA)改性多壁碳纳米管(MWCNTs),采用溶液法制备了聚丙烯(PP)/β-NA-MWCNTs复合材料.通过广角X射线衍射(WAXD)分析了复合材料的结晶形态,结果表明β-NA-MWCNTs诱导聚丙烯生成大量β晶,同时提高了复合材料的结晶度.含5.0 wt％β-N...     

Noncovalent functionalization of multiwalled carbon nanotubes using graft copolymer with naphthalene and its application as a reinforcing filler for poly(styrene‐co‐acrylonitrile)

A new compatibilizer, poly(vinyl benzyloxy ethyl naphthalene)‐graft‐poly(methyl methacrylate), for poly(styrene‐co‐acrylonirile) (SAN)/multi‐walled carbon nanotubes (MWCNTs) composites was synthesized. It has been identified that naphthalene unit in backbone of compatibilizer interacts with MWCNTs via π? π interaction and that the PMMA graft of the compatibilizer is miscible with the SAN matrix. When a small amount of compatibilizer was added to SAN/MWCNT composites, MWCNTs were more homogeneously dispersed in SAN matrix than the case without compatibilizer, indicating that the compatibilizer improves the compatibility between SAN and MWCNTs. As a consequence, mechanical and electrical properties of the composites with compatibilizer were largely improved as compared with those of composites without compatibilizer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4184–4191, 2010