八面沸石用(NH_4)_2SiF_6脱铝补硅的研究 Ⅲ.脱铝补硅沸石的性能

沸石的热稳定性、酸性和催化性能与沸石的Si/Al比有很大的关系.用(NH_4)_2SiF_6对Y型沸石进行脱铝补硅,能改变沸石的Si/Al比,并且脱铝沸石中非骨架铝少,结晶度好,很适合用于研究其物化性质与催化性能随Si/Al比的变化. 样品的制备及结构参数测试参阅文献〔1〕.沸石的组分分析采用湿法化学分析法。晶格破坏温度由DTA法测定.将厚度为10mg/cm~2的片状沸石,于1.33×10~(-2)～     

ICP-AES法测定镀铝锌(锌铝)合金彩涂板镀层中的铝锌硅镁镧铈

采用控温加热法退除涂层,用100g LNaOH溶液溶解镀层,研究了共存元素间干扰和酸度效应,建立了ICP AES法测定镀铝锌(锌铝)合金彩涂板镀层中Al、Zn、Si、Mg、La、Ce的方法,检出限(3σ)分别为19.8、2.4、6.3、0.3、4.6、7.6ng mL,相对标准偏差为0.2%～0.6%,回收率为99.3%～104.6%。     

钛硅分子筛中铝杂质对其性能的影响

 以四丙基溴化铵为模板剂,以硅溶胶为硅源,采用水热合成法制备了不同铝杂质含量的钛硅分子筛,并系统考察了铝杂质对钛硅分子筛性能的影响．结果表明,原料中的铝杂质可促进钛硅分子筛晶化,但同时也引入了酸性中心;在丙烯环氧化反应中,铝杂质形成的酸性中心会催化环氧丙烷与溶剂的副反应;加入少量碱性添加物可抑制铝杂质的酸催化作用,提高环氧丙烷的选择性,但过量碱性添加物会使钛硅分子筛失活．     

水对锂交换低硅铝比八面沸石吸附性能的影响

研究了变压吸附空气分离制氧吸附剂——锂交换低硅铝比八面沸石LiLSX中残留水及从外部引入的水对吸附性能的影响.研究表明，在水合LiLSX经脱附后，当残留的水分子数目为0～32（个分子/晶胞）时， N2或O2的吸附量下降显著.原因是N2和O2的吸附主要依赖于处在SIII位置的32个锂离子.当水分子与SIII位置的Li＋结合时，就会阻碍N2或O2的吸附.而从外部引入的水分子与脱附残留的水分子相比，在相同水含量时对吸附量的影响较小，这是由于吸附位置的不均匀性以及水分子在沸石中的扩散行为所引起.在水扩散进入LiLSX内部的过程中，一部分水分子可以吸附在能量较低的位置上而不是吸附到最强的SIII位置上.     

不同硅铝比Al-ITQ-13分子筛的甲醇制丙烯反应催化性能

采用晶种法直接合成了硅铝比(SiO_2/Al_2O_3物质的量比)为137、224和309的三种Al-ITQ-13分子筛,并采用粉末X射线衍射(XRD)、扫描电镜(SEM)、N_2吸附-脱附、固体核磁共振(MAS NMR)和NH_3-程序升温脱附(NH_3-TPD)等分析方法对不同硅铝比分子筛进行了表征,并在固定床微型反应评价装置上,考察了硅铝比对甲醇转化制丙烯反应性能的影响。结果表明,不同硅铝比Al-ITQ-13分子筛呈现出相似的织构性质,酸量及酸强度随着硅铝比的升高逐渐下降。硅铝比对甲醇转化反应的产物分布存在较大的影响;随着硅铝比的升高,氢转移反应和芳构化反应活性降低,使得乙烯选择性下降,而丙烯和丁烯的选择性升高。硅铝比由137提高到309,丙烯的选择性(质量分数)由46.04%增加到55.52%,而丙烯/乙烯比由3.39提高到6.57。     

ICP-AES法测定铝中铁、硅、铜、镓、镁、锌、锰和钛

用 50g L氢氧化钠溶液溶解铝样品 ,硝酸 (1 1 )酸化 ,以ICP AES测定其中铁、硅、铜、镓、镁、锌、锰和钛等 8种杂质元素。     

微波辐射法合成SAPO-5分子筛中硅铝比对产物结晶度和甲苯吸附性能的影响

采用硅溶胶作硅源, 用微波辐射法在酸性条件下(pH=4.5-5.0)合成了SAPO-5分子筛, 利用X射线衍射(XRD), 傅立叶变换红外光谱(FT-IR), 扫描电镜(SEM)和Brunauer-Emmett-Teller (BET)比表面积分析对样品的结晶度、形貌和比表面等进行表征, 考察了晶化原料硅铝比对分子筛结晶度和晶体颗粒长径比(c/a)的影响, 测定了分子筛对甲苯的吸附性能. 结果显示, 采用微波辐射法合成的SAPO-5分子筛, 在硅铝摩尔比为0.50附近生成产物的结晶度最好, 晶体颗粒的长径比最小(约为1.0). 尽管不同硅铝比条件下得到的样品比表面测定结果变化不大, 但对甲苯的吸附实验显示, 在硅铝比为0.50时样品的吸附速率和饱和吸附量均达到了最大值. 这与表征所得的结晶度和长径比的变化一致, 即结晶度好,长径比小的SAPO-5分子筛具有更好的甲苯吸附性能.     

ZSM-5分子筛硅铝比与其催化性能关系的量子化学研究

利用Gaussian03计算软件包,在DFT-B3LYP/3-21G水平上对ZSM-5分子筛128T簇模型进行了研究.通过分析T—O—T基团键角、桥羟基键长、质子电荷和分子轨道能隙等数据,讨论了ZSM-5分子筛硅铝比与其Br nsted酸性的关系,预测了其催化性能.计算结果表明,ZSM-5分子筛硅铝比越低,酸性越强,相应的催化性能越好,与实验结果相符.     

不同硅铝比ZSM-5的合成及其吸附脱除柴油中苯胺和吡啶的性能

合成了一系列不同硅铝比的ZSM-5分子筛,采用XRD、FT-IR、ICP、SEM、NH_3-TPD和N_2吸附-脱附等方法对其进行了表征,研究了不同硅铝比ZSM-5分子筛对模拟柴油中苯胺和吡啶的吸附脱除性能。结果表明,所合成的ZSM-5分子筛均具有典型MFI结构;与合成原料混合物中的硅铝比相比,实际硅铝比稍有降低。ZSM-5分子筛的酸量随硅铝比的增加而降低,硅铝比较小的ZSM-5(1)和ZSM-5(2)的吸附脱除苯胺或吡啶的效果明显优于其他样品,并且所有样品吸附脱除吡啶的效果均优于苯胺。ZSM-5(2)上苯胺和吡啶的吸附等温线符合Langmuir-Freundlich混合模型。     

低硅铝比ZSM-48分子筛合成及其正构十二烷临氢异构催化性能研究

通过静态水热合成法,溴化六甲二铵作为结构导向剂合成出系列低硅铝比的ZSM48沸石分子筛(Si/Al100),所合成样品中最低硅铝比为38.6(ICP-AES),这将拓宽ZSM-48高硅沸石分子筛的应用范围。制备Pt负载双功能催化剂,用于正构十二烷临氢异构催化反应。结果表明,硅铝比的改变可以影响催化剂的活性,投料硅铝比为70的双功能催化剂具有最优的催化性能,但硅铝比改变对异构产物的分布没有明显的影响,其异构产物以支链在中间位的异构体为主。     

Performance and Mechanisms of Fluoride Removal from Groundwater by Lanthanum-aluminum-loaded Hydrothermal Palygorskite Composite

Lanthanum-aluminum loaded hydrothermal palygorskite(La-Al-HP) composite was prepared and selected as adsorbent for the fluoride removal from simulated groundwater. The adsorbent was characterized by scanning electron microscopy(SEM), Brunauer-Emmet-Teller(BET) analysis, X-ray diffraction(XRD) analysis and X-ray photoelectron spectroscopy(XPS). SEM visualization shows that the dense surface structure of raw HP appeared loose and presented micro canals after modification. The BET analysis also proved the specific surface area of La-Al-HP composite(95.58 m²/g) was higher than that of the raw HP(34.31 m²/g). Subsequently, the adsorption capacity of La-Al-HP composite was demonstrated in adsorption experiments. The kinetics of fluoride ion adsorption into La-Al-HP composite followed the pseudo-second order with a correlation coefficient of 0.997. The isotherm data was well fitted with the Langmuir model. The monolayer adsorption capacity of La-Al-HP composite was 1.30 mg/g. The XRD and XPS results reveal that the La³⁺ and Al³⁺ ions were loaded on the surface of modified HP and the fluoride ion was adsorbed onto the La-Al-HP composite. A large amount of La-Al-O composite oxide existing on the surface of La-Al-HP composite might be the immanent cause for the excellent adsorption capacity of fluoride ions.     

High Performance Liquid Chromatography of Zinc and Copper Pheophytins

Abstract

The zinc or copper chelates of pheophytins a and b were formed and separated on a reversed-phase C-18 column. Allomerized products were produced readily during the chelation reaction. Resolution of the allomerized compounds from the non-allomerized chelates was achieved using a gradient elution technique. Compound identification was facilitated by monitoring the column eluate at both 436 and 658 nm. The method allowed for isolation of individual pigments for further study.     

Removal of Heavy Metals in Effluent by Adsorption and Coagulation

The silicate colloids with an average diameter 100 nm, were prepared by the hydrolysis of tetraethoxysilane (TES), NH4OH (30%) and then modified by (3-mercaptopropyl)trimethoxysilane (APS). The colloids can adsorb heavy metals such as Pb and Cr in effluent and after adsorption the colloids can be separated by coagulation of aluminum sulfate. The removal of heavy metals is up to 99%.     

5-氨基水杨酸锌及相关物质的高效液相色谱分析研究

对５－氨基水杨酸锌及相关物质５－氨基水杨酸、水杨酸、对氨基苯酚和５－苯偶氮基水杨酸的高效液相色谱法（ＨＰＬＣ）的分离条件进行了优化研究,结果表明,采用ＣＬＣ－ＯＤＳ（１５０ｍｍ×６．０ｍｍｉ．ｄ．,１０μｍ）作为分离柱,１％（Ｖ／Ｖ）ＨＡｃ－ＭｅＯＨ（４∶６）作为流动相,在流速为１ｍＬ／ｍｉｎ的情况下,上述５种物质在１０ｍｉｎ内可以达到基线分离,保留时间的日内和日间的变异系数分别小于２％和５％,在一定浓度范围内,浓度与峰面积的线性关系良好。     

膨胀石墨层间生长高活性氧化锌及其光催化性能

以醋酸锌和膨胀石墨为原料, 采用真空辅助压力诱导手段使反应溶液注入膨胀石墨层间, 在180℃下溶剂热反应12 h, 一步得到氧化锌纳米棒/石墨烯复合光催化剂, 采用X射线衍射仪(XRD)和透射电子显微镜(TEM)等对复合光催化剂的结构和形貌进行了表征. 结果表明, 合成的氧化锌纳米棒具有六方晶系纤锌矿结构; 氧化锌纳米棒在石墨烯表面分散性较好, 其平均直径约50 nm, 长度约150~200 nm. 所得氧化锌纳米棒/石墨烯复合材料对亚甲基蓝的降解效率优于目前应用最广泛的光催化剂Degussa P25.     

复合型高效絮凝脱色剂处理印染废水的研究

选用自制的双氰胺甲醛作为絮凝脱色剂处理高浓度印染废水,并与硫酸铝、三氯化铝作了对比实验。考察了投加量、pH值、反应温度等因素对絮凝效果的影响。实验结果表明在用量较少并且其它操作条件相同的情况下,双氰胺甲醛制备的脱色絮凝剂具有很好的絮凝脱色效果及COD_(Cr)去除率。在最佳的操作条件下(投加量120 mg/L,pH=7,反应温度25℃),此脱色絮凝剂对分散、酸性、活性印染废水的COD_(Cr)去除率分别为79.1%、78.5%、79.0%,对分散、酸性、活性印染废水的脱色率分别为94.0%、97.1%、72.9%,减轻了后续处理难度。在与无机絮凝剂的对比试验中,在相同的条件下有机絮凝剂的处理效果总体比无机絮凝剂的处理效果好。     

Efficiency and Mechanism of Phosphorus Removal by Coagulation of Iron-manganese Composited Oxide

Iron-manganese composited oxide(FeMnO) was prepared with potassium permanganate and ferrous salt. Interface performance, charge property and structure topography of the FeMnO were investigated. Coagulation efficiency and pollution removal mechanism of the FeMnO were approached. Results show that the main compositions of the FeMnO are δ-manganese dioxide and ferric hydroxide. The specific surface area is about 146.22 m2/g. The FeMnO contains rich hydroxyl with extremely strong adsorption action and chemical ...     

高性能锂-硫电池用复合正极的构造与粘结剂

采用球磨混合及热处理方法制备了含有多壁碳纳米管(MCNTs)的硫基复合正极材料,利用X射线衍射(XRD)和扫描电子显微镜(SEM)测定材料的结构和形貌,较系统地研究了MCNTs含量和粘结剂种类对硫基复合正极容量、循环稳定性和自放电行为等的影响.结果表明:MCNTs的合适含量为5%-8%(w,质量分数),以水性粘结剂环糊精制备的硫基复合正极电化学性能最佳.锂-硫电池在常温和半充电状态下放置30天几乎没有自放电;当电流倍率为0.1C时,β-环糊精为粘结剂的正极初始充电容量为687.7mAh.g-1,100次循环以后可逆容量为623.8mAh.g-1,容量保持率达90.7%.     

稀土对高强锌合金耐磨性和耐蚀性的影响

ＺＡ２７合金中加入稀土，由于合金化，变质等作用使合金微观组织发生变化，强化了合金，因此提高了合金的综合性能和耐磨性，又因稀土加入能净化晶界，对电化学性产生有利影响，所以合金的耐蚀性也得到改善。     

Enhanced Resolution of Conjugated Linoleic Acid Isomers by Tandem-Column Silver-Ion High Performance Liquid Chromatography

A commercial mixture of conjugated linoleic acid (CLA) isomers, reportedly consisting of six components, was recently resolved into 12 peaks attributed to CLA isomers using silver-ion high performance liquid chromatography (Ag⁺-HPLC). In this study, the coupling of two analytical silver-ion high performance liquid chromatography columns (tandem-column Ag⁺-HPLC) in series led to the enhanced resolution of CLA isomers. Many CLA isomers were baseline resolved and the pair 18 : 2 8,10 c/t and 18 : 2 7,9 c/t found in cheese products, was resolved for the first time. In this work, a similar commercial CLA mixture was separated into 16 peaks, while CLA isomers from cheese also gave rise to 16 peaks. As expected, the CLA isomers were separated into three geometric groups in the order trans,trans, cis/trans, and cis,cis. Semi-preparative Ag⁺-HPLC, followed by gas chromatography–mass spectroscopy of the dimethyloxazoline derivatives, was used to confirm the identity of the newly resolved positional CLA isomers. The double bond configuration of CLA isomers was established by gas chromatography–Fourier transform infrared spectroscopy. Two minor t,t CLA isomers found in cheese, presumably 18 : 2 t6t8 and 18 : 2 t13t15, were also separated. The CLA isomeric composition of 16 commercial cheese products was determined.