Preparation of silica–alumina composite membranes for hydrogen separation by multi-step pore modifications

In the present paper, a silica–alumina composite membrane for hydrogen separation was prepared within an α-alumina support by the multi-step pore modification. The α-alumina support has an asymmetric structure composed of a thin dense skin layer and a thick coarse layer and the average pore size of its skin layer is 80 nm. The composite membrane layer was formed in the vicinity of the interphase between the two layers of the support by two consecutive steps; namely, in situ silica sol–gel reaction and soaking and vapor deposition. In order to enhance the hydrogen selectivity, palladium (Pd) particles were impregnated in the final step utilizing Pd-acetate as a Pd precursor. Although both silica and Pd induced the surface diffusion, Pd was more effective for selective hydrogen adsorption than silica. This multi-step method produced a porous membrane with moderate hydrogen selectivity and satisfactory hydrogen permeance at high temperature and at high transmembrane pressure. The separation factor of hydrogen relative to nitrogen was maintained at about 10 even when the transmembrane pressure was as high as 110 kPa, and the hydrogen permeance was still much higher than that of non-porous polymeric membranes. In addition, the microstructural distributions of Si and Pd within the intermediate membrane layer were examined by a scanning electron microscopy (SEM) and an energy dispersive X-ray analysis (EDX)     

Preparation of hollow titania and strontium titanate spheres using sol–gel derived silica gel particles as templates

A facile approach, based on polyelectrolyte-mediated electrostatic adsorption of a water-soluble titanium complex on colloidal templates and hydrothermal treatment, is presented for the formation of hollow titania (TiO₂) and strontium titanate (SrTiO₃) spheres. Monodispersed silica gel particles were prepared by the sol?Cgel method and adopted as core templates. Deposition of a water-soluble titanium complex, titanium (IV) bis(ammoniumlactato)dihydroxide (TALH), on the silica gel particles was carried out via the layer-by-layer assembly technique. Hollow spheres were successfully formed from the core?Cshell particles. The silica gel particles used as core templates dissolved during hydrothermal treatment because of the particles?? undeveloped siloxane network. In addition, the hydrothermal treatment induced crystallization of the hollow shells. Therefore, the hydrothermal treatment played two roles; removal of the silica templates and crystallization of the hollow shells. When deionized water was used, hollow TiO₂ spheres were obtained. Hollow SrTiO₃ spheres could also be formed when an aqueous solution of Sr(OH)₂ was used. The approach presented here could be exploited as a novel and sustainable approach for the fabrication of a range of different inorganic hollow spheres.     

MOF-derived hollow NiO–ZnO composite micropolyhedra and their application in catalytic thermal decomposition of ammonium perchlorate

Ni(II)-doped Zn-based coordination polymer particles (Ni(II)-doped Zn-CPPs) with controllable shape and size were successfully synthesized by solvothermal method, which further transformed to porous ZnO–NiO composite micropolyhedra without significant alterations in shape by calcination in air. Those products were characterized by powder X-ray diffraction (XRD), field emission scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), infrared spectroscopy (IR) and gas adsorption measurements. The catalytic activity of ZnO–NiO composites for the thermal decomposition of ammonium perchlorate (AP) was investigated. The result shows that all ZnO–NiO composites efficiently catalyzed the thermal decomposition of AP, and NiO–ZnO composite hollow octahedrons have the highest catalytic efficiency compared with that of most materials reported to now, indicating that porous ZnO–NiO composite micropolyhedra could be a promising candidate material for application in AP-based propellant.     

Stability and performance of porous silica–zirconia composite membranes for pervaporation of aqueous organic solutions

Porous silica–zirconia membranes were fabricated by the sol–gel techniques to study their stability against water and the pervaporation performance of aqueous solutions of organic solvents. Zirconia (10–70 mol%) was added to silica to obtain silica–zirconia composite membranes by firing at 400–500 °C for pervaporation tests with organic solvent/water mixtures, such as iso-propyl alcohol (IPA)/water and tetrahydrofuran (THF)/water mixtures at their normal boiling points.The membrane coatings have been done effectively by the hot-coating methods proposed previously. Boiling water treatments introduced in the coating processes have made the membranes quite stable even in the high water concentration region of aqueous organic solutions at their normal boiling points. Zirconia contents larger than about 40 mol% have made the silica–zirconia membranes quite stable. The membranes of zirconia contents less than about 30 mol% were found not stable in a dilute aqueous solution of IPA. The membranes fabricated by the conventional dip-coating methods with slow drying were not stable against water because of the probable segregation of silica and/or silica-rich phases during drying.The membranes fired at lower temperature (400 °C) gave a higher water flux of around 500 mol m⁻² h⁻¹ (9 kg m⁻² h⁻¹) with a separation factor larger than 1500 at 10 wt.% of water in the boiling feed of IPA/water mixture, for example.     

Study on the synthesis,morphology and structural analysis of fly ash–cyclodextrin composite

This study investigates the surface morphology, structure analysis and the effect on the porosity and particle size of a new composite prepared using fly ash with α and β cyclodextrins. The dry mix and solution methods were used to synthesize these composite samples. The X-ray diffraction analysis shows the new peaks that indicate the interaction between the materials. These results are in agreement with the Fourier transform infrared spectroscopic analysis that suggested the possibility of interaction of fly ash particles with cyclodextrin. Morphology changes between the composite material and the constituent materials were observed using the scanning electron microscopic. The porosity and particle size analyses show the significant changes with respect to preparation methods.     

Influence of processing parameters on regeneration kinetics and morphology of porous cellulose from cellulose–NaOH–water solutions

The kinetics of cellulose regeneration in acetic acid bath from cellulose–8% NaOH–water solutions and gels is studied as a function of gelation conditions, acid concentration and bath temperature. The diffusion coefficient of NaOH from cellulose solution or gel into regenerating bath was calculated. It does not depend either on gelation mode or on acid concentration. On the contrary, cellulose regeneration from non-gelled solutions is slower than from a gel. The increase in bath temperature induces diffusion coefficient increase obeying Arrhenius law. Scanning electron microscopy images of regenerated swollen-in-water freeze-dried cellulose and of the same samples dried in supercritical CO₂ show highly porous morphology. CEMEF is a Member of the European Polysaccharide Network of Excellence (EPNOE), .     

Influence of ethyl alcohol in the preparation, morphology and properties of compound DAS–Eu3+ and its thermal degradation products

In this study, two compounds presenting characteristics different from each other were produced from there action between hydrated Eu³⁺ sulfate and Ba²⁺ diphenylamine-4-sulfonate using, respectively, aqueous solution for producing the Eu(C₁₂H₁₀NSO₃)₃·7H₂O (A) compound and water/ethyl alcohol (7:1) solution for the Eu(C₁₂H₁₀NSO₃)₃·5H₂O (B) production. The presence of alcohol molecules in the solution will interfere in the structural arrangement of anionic surfactant DAS^? (diphenylamine-4-sulfonate) around the metal ions Eu³⁺ allowing differentiation in the stoichiometric formulas, morphology, and thermal properties of these compounds and their derivatives. Thus, when treating both compounds under oxidizing atmosphere, we found different temperatures of the water loss and conversion of the intermediate pair oxydisulfate [Eu₂O(SO₄)₂]/dioxysulfate [(Eu₂O₂SO₄)]. However, the effect of water/surfactant/alcohol interactions in the metal ion structural arrangement becomes still more evident under reducing atmosphere. After this thermal treatment, significant changes were observed in the morphological characteristics and physical properties of the (Eu₂O₂S oxysulfide) in compound B with respect to compound A.     

Preparation of carbon supported Pd–Pb hollow nanospheres and their electrocatalytic activities for formic acid oxidation

Pd–Pb hollow nanospheres dispersed on carbon black were developed by a galvanic replacement reaction between sacrificial cobalt nanoparticles and Pd²⁺, Pb²⁺ ions. The as-prepared catalysts were characterized by transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD). The electrochemical measurements show that the as-prepared catalysts have excellent catalytic activity for formic acid electrooxidation, which is attributed to the large surface area caused by the hollow structure and the lead doping effect which might modify the electronic structure of the catalysts.     

Effect of hydrophobicity on the stability of sol–gel silica coatings in vacuum and their laser damage threshold

Silica antireflective coatings modified by hexamethyldisilazane (HMDS) were deposited on clean substrates (silicon wafer or K9 glass blanks) by sol–gel processing. The effects of HMDS on the contamination resistant capability and laser-induced damage threshold (LIDT) of coatings were investigated. Transmission electron microscopy revealed that a stable sol with uniformly distributed silica particles with an average particle size of about 15 nm was acquired by adding appropriate amount of HMDS into the standard SiO₂ sol. With the modified sol the resultant coatings were hydrophobic and the contact angle for water increased with increasing amount of HMDS in the reaction mixture. Such increase in hydrophobicity was not the result of surface roughness. The antireflective properties were retained after HMDS-treatment and the maximum transmission values were above 99 %. The introduction of HMDS into silica sols had also increased the LIDT of coatings from 24.3 to 37.0 J cm^?2 when the molar ratio of HMDS to tetraethoxysilane was 0.05:1. The increase in LIDT was attributed to the decrease of nodular defect and uniform microstructures of coatings as an effect of the HMDS modification. After some of the hydroxyl groups on the surface of the SiO₂ particle were replaced by methyl groups, from which the SiO₂ particle gained a water-repellent surface, the stability of coatings in vacuum was increased. The maximum transmission values of modified coatings decreased by only 0.25 % after storage under vacuum for 168 h. In contrast, the standard sol–gel silica coatings decreased about 2 % under similar conditions. The LIDT of modified coatings remained as high as 30.8 J cm^?2, more than that of standard coatings stored for the same duration in air.     

PVC-silica hybrids: effect of sol–gel conditions on the morphology of silica particles and thermal mechanical properties of the hybrids

Hybrid materials from poly(vinyl chloride) (PVC) and silica have been prepared using different conditions by the sol–gel technique. In situ generation of silica network in the PVC matrix was carried out by hydrolysis/condensation of tetraethoxysilane (TEOS) in the matrix. Morphology of the silica particles produced in hybrid films was studied by scattering electron microscopy. The shape of silica particle produced in the matrix was modified by carrying out the sol–gel process under steam on the hybrid films using TEOS. The films were subjected to strain conditions during this process, which produced lamellar shaped particles in the matrix. It was possible to produce platelet type of structure with different aspect ratio by changing the composition and the stress conditions on the films during the steaming process. Addition of a very small amount of γ-glycidoxypropyltrimethoxysilane as compatibilizer drastically reduced the silica particles size in the matrix to nano-level. Thermal–mechanical properties of some of these hybrids were studied and related to the composition, structure and inter-phase interaction between the silica and the matrix.     

Influence of water-soluble derivatives of [60]fullerene on catalytic activity of monoaminе oxidase B and their membranotropic properties

Russian Chemical Bulletin - The effect of two water-soluble derivatives of [60]fullerene (WS[60]FDs) on mitochondrial monoamine oxidase B (MAO-B) involved in oxidative deamination of biogenic...     

Effect of sol–gel derived in situ silica on the morphology and mechanical behavior of natural rubber and acrylonitrile butadiene rubber blends

Silica particles were generated and grown in situ by sol–gel method into rubber blends comprised of natural rubber (NR) and acrylonitrile butadiene rubber (NBR) at various blend ratios. Silica formed into rubber matrix was amorphous in nature. Amount of in situ silica increased with increase in natural rubber proportion in the blends during the sol–gel process. Morphology studies showed that the generated in situ silica were nanoparticles of different shapes and sizes mostly grown into the NR phase of the blends. In situ silica filled NR/NBR blend composites showed improvement in the mechanical and dynamic mechanical behaviors in comparison to those of the unfilled and externally filled NR/NBR blend composites. For the NR/NBR blend at 40/60 composition, in particular, the improvement was appreciable where size and dispersion of the silica particles into the rubber matrix were found to be more uniform. Dynamic mechanical analysis revealed a strong rubber–in situ silica interaction as indicated by a positive shift of the glass transition temperature of both the rubber phases in the blends.     

Influence of the synthesis conditions on the structure and composition of the titanium–magnesium nanocatalyst and on its activity in isoprene polymerization

Synthesis of titanium–magnesium nanocatalyst in a high-pressure reactor under the conditions modeling the industrial conditions was studied. A laboratory scale plant including the units for the product synthesis, washing, and filtration was developed. The effect of elevated pressure (10–90 atm) on the process course, on the properties of the catalyst formed, and on the isoprene polymerization was studied for the first time. An increase in pressure leads to an increase in titanium incorporation into the catalyst from 1.52 to 2–2.3 wt % and simultaneously to an increase in the trivalent titanium content to 81 wt %. The titanium–magnesium nanocatalyst with such properties exhibits enhanced performance in isoprene polymerization without deteriorating the polymer microstructure. The development of the catalyst synthesis procedure on the laboratory scale plant will allow pilot-scale modeling of this process in the future.     

Visible light photocatalytic activity and Photoelectrochemical property of Fe-doped TiO<Subscript>2</Subscript> hollow spheres by sol–gel method

Fe-doped TiO₂ hollow spheres (Fe-THs) were synthesized by sol–gel process using carbon spheres as templates. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectrum (DRS), N₂ adsorption–desorption isotherms, Electron paramagnetic resonance (EPR) spectroscopy and Photoluminescence emission spectroscopy (PL). UV–vis spectra showed that Fe³⁺ doping could extend the absorption edge to the visible region. EPR spectra showed that Fe³⁺ was incorporated into the crystal lattice of TiO₂, which could inhibit the recombination of photo-induced electron–hole pairs and improve the photocatalytic activity. The photocatalytic activities of the prepared samples were evaluated for the degradation of dye Reactive Brilliant Red X-3B (C.I. reactive red 2) under visible light irradiation. The results indicated that Fe³⁺ doping sample showed the highest photocatalytic activity with an optimal doping concentration of 0.50 wt%. The recycle ability of the Fe-THs was also investigated. After 5 cycles, the degradation rate was still higher than 90%, decreased by only 6.36% compared to the first cycle. Moreover, in order to characterize the electron-transferring efficiency in the process of photocatalysis reaction, a photocurrent-time spectrum was examined by anodic photocurrent response.     

Pervaporation dehydration of alcohol–water mixtures: Optimization for permeate flux and selectivity by central composite rotatable design

A central composite rotatable design (CCRD) of response surface methodology was used to analyze pervaporation performance of homogeneous poly(vinyl alcohol) (PVA) membranes. A regression model was developed for the pervaporation flux and selectivity as a function of the operating conditions: temperature, concentration and flow-rate. Dehydration experiments were performed on two different alcohol–water systems: isopropanol–water (IPA–water) and ethanol–water (Et–water) mixtures around their azeotropic concentrations. Based on preliminary experiments and CCRD design, the ranges of values of the operating conditions were selected: temperature 33–67 °C, feed flow-rate 46–114 L/h, and concentration 83–92 wt% for IPA and 93–98 wt% for Et in feed mixtures. A total of 20 pervaporation experiments were conducted for each alcohol–water system. Judged by the lack-of-fit criterion, the analysis of variance (ANOVA) showed the regression model to be adequate. From the regression analysis, the flux and selectivity were expressed with quadratic equations of temperature, feed concentration and flow-rate. The predicted flux and selectivity from the regression model were presented in 3D surface plots. For both alcohol–water systems, quadratic terms of temperature and feed alcohol concentration showed significant (p < 0.0001) influence on the flux and selectivity. A strong interaction effect of temperature and concentration was observed on the selectivity for the Et–water system. However, the interaction of flow-rate with temperature or concentration was found to be less significant. In order to optimize the pervaporation flux and selectivity of azeotropic alcohol–water mixtures, the desirability function approach was applied to analyze the regression model equations by commercial software. For the azeotropic IPA–water mixture (87.5 wt% IPA), the optimized dehydration variables were found to be 50.5 °C and 93.7 L/h for temperature and flow-rate, respectively. For the azeotropic Et–water mixture (95.5 wt% Et), the optimized temperature and flow-rate were found to be 57 °C and 89.2 L/h, respectively. Compared with experiments performed at optimized temperature and flow-rate, the predicted flux and selectivity of the azeotropic mixtures showed errors to be within 3–6%.     

Cationic–anionic palladium complexes: effect of hydrogen bond character on their stability and biological activity

The solution state of palladium cationic–anionic complexes (AmH _n ) _k [PdCl₄] prepared for the first time, where Am is morpholine, methylmorpholine, aminoethylmorpholine, 5-aminovaleric acid, L-1-phenyl-2-methylaminopropanol, and m-xylilenediamine, has been studied by electronic absorption spectroscopy, NMR, and pH measurements. The agreement of obtained results for the state of the complexes in water and NaCl solutions with IR and X-ray diffraction data for these complexes has allowed us to substantiate the principle for designing patent formulation (C₅H₁₂NO)₂[PdCl₄], a new type of palladium complexes, palladium(II) cationic–anionic complexes showing high antitumor and antimetastatic activity. Crystallographic data for six obtained complexes have been presented.