Non-isothermal crystallization and crystalline structure Of PP/POE blends

Polypropylene (PP) /ethylene-octene copolymer (POE) blends with different content of POE were prepared by mixing chamber of a Haake torque rheometer. The crystallization behaviors and crystal structure of PP/POE blends were systematically investigated by differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and polarized optical microscopy (POM). The results showed that PP spherulites became defective and the crystallization behavior was influenced intensely with the introduction of POE. At the low content of POE, the addition of POE decreases the apparent incubation period (Δt _i) and the apparent total crystallization period (Δt _c) of PP in blends due to the heterogeneous nucleation of POE, and small amount of β-form PP crystals form because of the existence of POE. However, at high content of POE, the addition of POE decreases the mobility of PP segments due to their strong intermolecular interaction and chain entanglements, resulting in retarding the crystallization of PP, decreasing in the amount of β-form PP crystals, and increasing in Δt _i and Δt _c of PP in blends.     

Non-isothermal crystallization and oxygen permeability of PP/PLA/EVOH ternary blends

Journal of Thermal Analysis and Calorimetry - Casting films of polypropylene (PP), poly(lactic acid) (PLA) and ethylene vinyl alcohol copolymer (EVOH) ternary blends having different compositions...     

Influence of multiwall carbon nanotubes on morphology and electrical conductivity of PP/ABS blends

Polypropylene (PP) and acrylonitrile‐butadiene‐styrene (ABS) blends with multiwall carbon nanotubes (MWNT) were prepared by melt mixing. PP/ABS blends without MWNT revealed coarse co continuous structures on varying the ABS content from 40 to 70 wt %. Bulk electrical conductivity of the blends showed lower percolation threshold (0.4–0.5 wt %) in the 45/55 co continuous blends whereas the percolation threshold was between 2 and 3 wt % in matrix‐particle dispersed morphology of 80/20 blends. Interestingly, droplet size was observed to decrease with addition of MWNT above percolation threshold in 80/20 blends. Further, the bulk electrical conductivity was found to be dependent on the melt flow index of PP. The non‐polar or weakly polar nature of blends constituents resulted in the temperature independent dielectric constant, dielectric loss, and DC electrical conductivity. Rheological analysis revealed the formation of 3D network‐like structure in 80/20 PP/ABS blends at 3 wt % MWNT. An attempt was made to understand the relationship between rheology, morphology, and electrical conductivity of these blends. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2286–2295, 2008     

Mutual influence of LDPE and PP in their blends during crystallization

An indication for the mutual influence of LDPE and PP was the change of the morphology parameters of PE and PP at different ratios of the polymers in blends. That influence depends on the blend composition and is different for PE and PP. It is especially interesting in the blend PE75/PP25 where the influence between PE and PP shows dependence also on the sample geometry. Melting parameters, non-isothermal crystallization parameters - crystallization peak temperature T_c, crystallization begin temperature T_onset, half-width w_1/2 of the crystallization peak, degree of crystallinity α and crystallization rate coefficient CRC, as well as the isothermal kinetics parameters showed dependence on the blend composition. It was established that PE is more stable then PP concerning the mutual influence of both polymers on their crystallization. It was established that PE affects the crystal nucleation of PP and causes a decreasing of PP spherulite size.     

Morphology and non-isothermal crystallization of dynamically vulcanized PP/EPDM blends in situ compatibilized via magnesium dimethacrylate

Polypropylene/ethylene-propylene-diene rubber (PP/EPDM) blends in situ compatibilized by magnesium dimethacrylate (MDMA) were fabricated via peroxide-induced dynamic vulcanization. Scanning electron microscope observation indicated that the size of cross-linked EPDM particles decreased with incorporation of MDMA. Polarizing Optical Microscope (POM) analysis suggested that the spherulite size of PP phase decreased sharply with incorporation of MDMA during dynamic vulcanization. The Pseudo-Avrami, Ozawa and Mo's models were applied to analyze the non-isothermal crystallization kinetics of the composites. The analyzed data indicated that the crosslinked EPDM particles and homopolymerized MDMA acted as heterogeneous nucleating agents, which enhanced the crystallizability and decreased the spherulite size of the PP phase. In addition, the non-isothermal crystallization activation energy (ΔE) was calculated through the Kissinger and Friedman methods, and the ΔE value was found increase with incorporation of MDMA.     

Fractionated crystallization and morphology of PP/PS blends in the presence of silica nanoparticles with different surface chemistries

The fractionated crystallization behavior of polypropylene (PP) droplets in its 20/80 blends with polystyrene (PS) in the presence of hydrophilic or hydrophobic fumed silica nanoparticles was studied by using differential scanning calorimetry, scanning electron microscopy, and transmission electron microscopy. It was found that the fractionated crystallization of PP droplets in the PS matrix was promoted by adding a low content of hydrophobic or hydrophilic nanoparticles due to their morphological refinement effect. However, discrepancies in the fractionated crystallization behavior of PP droplets occurred as the nanoparticle content increased. The crystallization became dominated by the heterogeneous nucleation effect of high content of hydrophilic nanoparticles, which possibly migrated into PP droplets during mixing and significantly suppressed their fractionated crystallization. In contrast, the morphological refinement effect still played a dominated role in promoting the fractionated crystallization of PP droplets in PP/PS blends filled with higher content hydrophobic nanoparticles as a result of the efficiently morphological refinement effect.     

Interfacial effect on photo-oxidation of PP via model blends

The interface in multiphase material plays an important role not only in mechanical properties, but also in aging behavior. This article uses polypropylene/polymethyl methacrylate (PP/PMMA) and polypropylene/polystyrene (PP/PS) blends (PMMA and PS as dispersion phase) as models to investigate the interfacial effect on the photo-oxidative aging of PP. The chemical property and stability of dispersed phase could make big difference on aging behavior of PP. PMMA, with polar functional group at the interface, accelerated the photo-oxidation of PP, while PS, with inert functional group at the interface, had little influence. Both the dispersion phases have little effects on crystallization of PP and the oxygen diffusion. The photo degradation product of PMMA could help to initiate or accelerate aging of PP mainly via free radicals transfer. Grafting reaction happened in the interface and the interfacial cohesion of PP and PMMA enhanced thereby.     

The effect of compatibilizing and coupling agents on the mechanical properties of glass bead filled PP/PET blends

PP/PET blends (95/5) filled with 50% by weight of glass beads were prepared and studied at morphological and mechanical level, and compared with its analogous samples of glass bead-filled PP. The influence of a compatibilizing agent (maleic anhydride grafted polypropylene) and different silane coupling agents was analysed. It has been found that PET embeds glass bead surface independently on the silane coupling agent employed. Addition of MAPP in PP/PET blends leaded to tensile strength values similar to those of unfilled PP, but rupture takes place in a brittle manner.     

Deformation mechanisms in nylon 6/ABS blends

The deformation mechanisms during fracture of a Nylon 6/ABS blend compatibilized with an imidized acrylic polymer were compared to those of an uncompatibilized blend. A postmortem examination of deformed zones in samples loaded to failure in a double-notch four-point-bend geometry was made using transmission electron microscopy (TEM). For the compatibilized blend, cavitation of the rubber particles followed by massive shear yielding of the polyamide matrix was concluded to be the sequence of events leading to toughness; while, for the brittle uncompatibilized blend, the evidence indicated that a lack of adhesion at the Nylon-ABS interface prevented the rubber particles from cavitating and the subsequent plastic deformation of the polyamide matrix. © 1994 John Wiley & Sons, Inc.     

Evaluation of the SEBS copolymer in the compatibility of PP/ABS blends through mechanical,thermal, thermomechanical properties,and morphology

Polypropylene (PP) blends with acrylonitrile-butadiene-styrene (ABS) were prepared using the styrene-ethylene-butylene-styrene copolymer (SEBS) as a compatibilizing agent. The blends were prepared in a co-rotational twin-screw extruder and injection molded. Torque rheometry, Izod impact strength, tensile strength, heat deflection temperature (HDT), differential scanning calorimetry, thermogravimetry, and scanning electron microscopy properties were investigated. The results showed that there was an increase in the torque of PA6/ABS blends with SEBS addition. The PP/ABS/SEBS (60/25/15%) blend showed significant improvement in impact strength, elongation at break, thermal stability, and HDT compared with neat PP. The elastic modulus and tensile strength have not been significantly reduced. The degree of crystallinity and the crystalline melting temperature increased, indicating a nucleating effect of ABS. The PP/ABS blends compatibilized with 12.5% and 15% SEBS presented morphology with well-distributed fine ABS particles with good interfacial adhesion. As a result, thermal stability has been improved over pure PP and the mechanical properties have been increased, especially impact strength. In general, the addition of the SEBS copolymer as the PP/ABS blend compatibilizer has the advantage of refining the blend's morphology, increasing its toughness and thermal stability, without jeopardizing other PP properties.     

The effect of annealing on the crystallization of poly(ethylene terephthalate)/polycarbonate blends

The effect of annealing on the morphology and subsequent crystallization kinetics of poly (ethylene terephthalate)/polycarbonate blends have been investigated using differential scanning calorimetry (DSC), polarized light microscopy, and scanning electron microscopy (SEM). During annealing transesterification and phase coarsening occurred, and the final properties were compromizes between these two competing effects. Initially, the effect of phase separation dominated and the rate of cold crystallization of PET increased. Transesterification, however, became increasingly important and the rate of crystallization decreased progressively until finally the blend completely lost the ability to crystallize. At this stage in the reaction a single glass transition was observed and uniform glassy material observed in the SEM. The maximum crystallinity of the blend achieved on heating showed the same trend in first increasing and then decreasing with annealing time. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2129–2136, 2004     

Preparation and properties of PP/PC/POE blends

In order to develop PP (polypropylene)‐based blends with balanced toughness and rigidity, the poly‐blends of PP/PC (polycarbonate)/POE (ethylene–octene copolymer) were prepared by applying styrene–ethylene–propylene–styrene (SEPS) as the macromolecular compatibilizer. The compatibilizing effect was studied in terms of the mechanical, morphologies and thermal properties, and the compatibilized PP‐based blends presented remarkable improvement in impact toughness and balanced tensile strength due to the formed special morphology structure. Additionally, by preparing the pre‐blend of PC/SEPS, the melt viscosity of the PP matrix can match that of the dispersed phase PC and POE, which led to a further improvement in the mechanical property of the blends. Copyright © 2009 John Wiley & Sons, Ltd.     

PC/ABS blends: Compatibilization and mechanical behaviour

PC/ABS(M) blends, encompassing the whole composition range between pure PC and ABS(M), were prepared by melt-mixing in a Brabender-like apparatus. Thermal, mechanical and impact tests were performed on compression moulded specimens. Inward Tg shifts were detected for PC and ABS(M) in the blends with respect to pure PC and ABS(M) values, indicating an interaction between the component domains. This finding was confirmed by the comparison of the experimental tensile moduli with the Kernels model predictions, showing an evidence of a good adhesion between the phases. A synergistic effect was observed for the impact strength as well as for the maximum stress at an ABS(M) blend content of about 25 weight %. All the results are interpreted on the basis of an interlayer existing at the boundary between the PC and ABS phases. A preliminary investigation on the influence of the ABS internal composition, keeping constant all the other conditions (mixing, processing, specimen preparation), was carried out as well. Differences in the properties of PC/ABS(M) and PC/ABS(B) blends are thoroughly discussed. The compatibility between PC and ABS domains seems to be scarcely influenced by such a parameter in these blends.     

Effect of PEG on the crystallization of PPDO/PEG blends

A new biodegradable polymer system, poly(p-dioxanone) (PPDO)/poly(ethylene glycol) (PEG) blend was prepared by a solvent casting method using chloroform as a co-solvent. The PPDO/PEG blends have different weight ratios of 95/5, 90/10, 80/20 and 70/30. Crystallization of homopolymers and blends were investigated by differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD). When 5% of PEG was blended, the crystallization exothermal peaks (T_c) of PPDO increased sharply and the crystallization exothermal peaks (T_c) of PEG decreased slightly compared with the homopolymers. The crystallization rates of both components increased, and caused greater relative crystallization degree (X_t%). But when the content of PEG was more than 5%, the crystalline behaviors of blends had no more significant changes accordingly. The melting points of each sample varied little over the entire composition range in this study. The nonisothermal crystallization of PPDO homopolymer and blend (PPDO/PEG = 70/30) were also studied by DSC. The crystallization began at a higher temperature when the cooling rates were slower. The nonisothermal crystallization kinetics of blends was analyzed by Ozawa equation. The results showed that the Ozawa equation failed to describe the whole crystallization of the blend, but Mo equation could depict the nonisothermal crystallization perfectly.     

PP/EPDM共混物热氧稳定性研究

通过热氧加速老化的方法研究了不同的EPDM含量和抗氧剂对聚丙烯和三元乙丙橡胶共混物(PP/EPDM)热氧稳定性的影响.通过对老化前后试样的力学性能变化分析,热失重(TG)分析和扫描电镜(SEM)分析,结果表明:在热氧加速老化的初期,PP/EPDM共混物的拉伸强度随着时间的增长呈逐渐上升的趋势;在老化中期,共混物的拉伸强度变化不大;在老化后期,共混物的拉伸强度逐渐下降.在整个老化过程中,断裂伸长率都呈逐渐下降的趋势.而随着EPDM含量的增加,相应共混物的拉伸强度和断裂伸长率的下降减缓;相应共混物的分解温度得到较大的提高;抗氧剂的加入,能进一步提高共混物的热氧稳定性.     

PP/尼龙66/聚碳酸酯/ABS共混高聚物的SEM样品制作

讨论了PP／尼龙66／聚碳酸酯／ABS共混高聚物的扫描电子显微镜样品制作中存在的问题,通过实验,探讨了出该材料最佳的样品制作条件。     

Solvent sorption effects on the structure and properties of PP/Rodrun blends

Toluene, carbon tetrachloride, and tetrahydrofuran sorption and desorption by polypropylene (PP) and PP/thermotropic liquid crystal polymer (Rodrun) blends with 20 and 40% Rodrun contents were studied as well as the effects of the solvent presence on the structure and mechanical properties. The rate of sorption and desorption and the solvent content at the equilibrium were higher in the blends than in pure PP. This was attributed to microcracking in the PP matrix induced by the presence of Rodrun. Taking into account the very low permeability of Rodrun to the solvents of this work, and the increase in specific volume of the blends as a result of sorption, sorption‐induced additional microcracking, partially in the form of debonding of the dispersed Rodrun phase, is also believed to occur. Plasticization was the main effect on mechanical properties. The partially irreversible effect of sorption on the mechanical properties agrees with the proposed partial debonding and weak solvent resistance of these blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1090–1100, 2000