Investigation of mechanochemical synthesis of zeolite NaA made of metakaolin in the mills with shock-shear type of strain

The possibility of obtaining of the NaA zeolite using dry mixture in a mill with a shock-shear type of strain with anhydrous raw ingredients, metakaolin, aluminium oxide, sodium aluminate was examined. The optimal time of mechanical activation was found.     

分子筛改性对一步法合成二甲醚的影响

采用浸渍法制备了MgO、CaO、ZnO改性的HZSM 5分子筛,并以改性HZSM 5为脱水剂与JC207甲醇合成催化剂组成双功能催化剂,在固定床反应器上考察了其对一步法合成二甲醚影响。结果表明,适量碱性氧化物的引入,引起分子筛表面的B酸中心（强酸中心）向L酸中心（弱酸中心）转变,而弱酸和中强酸中心是甲醇脱水生成二甲醚的活性中心,强酸中心会造成二甲醚进一步脱水生成烃类副产品,所以改性后产物中二氧化碳和烃类的选择性下降,二甲醚选择性升高。这种趋势在CaO/HZSM 5脱水剂上表现的更为明显。     

A study of thermal treatment and hydrothermal crystallization stages in production of granulated NaA zeolite from mechanically activated metakaolin

NaA zeolite was synthesized from mechanically activated granulated mixtures of metakaolin, sodium hydroxide, and aluminum oxide. The thermal treatment and hydrothermal crystallization processes were studied. It is shown that the optimal temperature of thermal treatment of grains based on a mechanically activated metakaolin is 600°C at a NaA zeolite content of about 65 wt %. Raising the calcination temperature leads to a decrease in the content of the zeolite and to formation of nepheline. It was found that the optimal concentration of the crystallization solution of NaOH is 2–4 M. Under these conditions, the content of the zeolite exceeds 90 wt %. Raising the alkali concentration leads to a decrease in the content of the zeolite and to its recrystallization into sodalite.     

Effect of thermal treatment conditions on the acid properties of zeolite Beta

The acid properties of zeolite Beta were studied by IR spectroscopy with the use of adsorbed NH₃ and CO probe molecules. It was found that the strength of the Brønsted acid sites (BASs) of zeolite Beta was the same as that of zeolite ZSM-5. Approximately a third of the total amount of BASs participated in the formation of hydrogen bonds at interdomain boundaries; thus, they were inaccessible to molecules larger than the ammonia molecule. The qualitative and quantitative compositions of acid sites in zeolite Beta can be regulated by changing the conditions of calcination of the initial zeolite form (temperature and/or gas atmosphere). Calcination under vacuum conditions afforded the highest acidity of the zeolite with respect to all types of acid sites. Calcination in a flow of air resulted in the lowest acidity of the sample, especially, with respect to the concentration of strong Lewis acid sites, because of the formation of an alumina phase. Calcination in an atmosphere of helium resulted in a decrease (as compared with a vacuum) in the rate of removal of the organic template decomposition products of the initial zeolite form from the channel volume. The resulting ethylene was mainly adsorbed at strong Lewis sites and converted into undesorbed condensation products.     

Combined effect of zeolite and boric acid on thermal behavior of epoxy composites

The particles of natural zeolite in combination with boric acid were incorporated into the epoxy resin ED-20 in order to improve the thermal stability of epoxy polymer. Epoxy resin was cured using polyethylenepolyamine. Characterization of the epoxy composites was carried out by using Fourier transform infrared spectrometry, thermogravimetric analysis (TG) and differential scanning calorimetry (DSC) under flow of air and argon. The thermal behavior of the zeolite/boric acid-based epoxy composites (total percentage 15 mass%) were compared with that of 15 mass% boric acid-based epoxy system and the neat epoxy resin. TG and DSC results revealed that the combination of 5 mass% zeolite and 10 mass% boric acid significantly increased the mid-point temperature and residue, and decreased the maximum decomposition rate of the epoxy composites at the heating.     

Modeling of liquid fuel purification by the LTA zeolite using machine learning methods

Journal of Thermal Analysis and Calorimetry - Impurities have severe negative influences on both the application and energy content of the dimethyl aminoethyl azide (DMAZ) fuel. Therefore, it is...     

Effect of synthesis parameters on the crystallinity of EU-1 zeolite for the m-xylene isomerization reaction

Russian Journal of Applied Chemistry - The EU-1 zeolite with Si/Al = 25 was synthesized by hexamethonium bromide as a template. The effects of crystallization time, synthesis temperature, and the...     

Template method for the synthesis of a heterogeneous fenton catalyst based on the hierarchical zeolite FeZSM-5

Zeolite h-FeZSM-5 with a hierarchical micro/macropore system has been synthesized in the presence of a template based on the close-packed polystyrene (PS) spheres, and the conventional zeolite FeZSM-5 has been obtained in the absence of a PS template. The zeolites have been characterized by X-ray diffraction, scanning and high-resolution transmission electron microscopy, and N₂ sorption. The macropore walls of the hierarchical zeolite consist of ZSM-5 nanocrystals and amorphous globules of silica. Compared to the conventional zeolite, the hierarchical one has a high BET and external surface areas of 245 and 472 m²/g, respectively, and a high pore volume of 0.6 cm³/g. The catalytic properties of the Fe-containing zeolites were studied in the H₂O₂ decomposition reaction in the absence and in the presence of EDTA ligands and in the oxidation of low- and high-molecular-weight organic compounds by hydrogen peroxide at 25°C. Hierarchical zeolite h-FeZSM-5 is highly efficient in the oxidation of large molecules.     

Effect of composition on the thermal behavior of NiMnGa alloys

The methods to determine martensitic transformation temperature, enthalpy and entropy change, specific heat capacity change with temperature, and transformation activation energies of Ni–%29.5Mn–%21Ga, Ni–%29Mn–%21Ga, Ni–%29.5Mn–%20Ga, and Ni–%28.5Mn–%20.5Ga (atomic percentage) alloys were investigated by differential scanning calorimetry. It was observed that the transformation temperature increased with an increase in atomic nickel ratio. Meanwhile, it was detected that the change in enthalpy increases with the amount of nickel. The highest values of entropy change and the heat capacity at room temperature were observed in the alloy having the least amount of nickel in it.     

The thermal behaviour of the hydroxide mixtures used for the synthesis of MgFe2O4 spinel

The thermal behaviour of hydroxide mixtures, precursors to the synthesis of MgFe₂O₄ spinel powders, was investigated.The mixtures of hydroxides were prepared by coprecipitation reaction from nitrate solutions with an Mg/Fe atomic ratio of 12. The results were related to the thermal behaviour of separately precipitated components of the hydroxide mixtures. Samples prepared by mechanically mixing the separately precipitated hydroxides were also studied.The spinel formation temperature was identified by performing XRD analysis on powder samples heated to different temperatures. The presence of spinel from the thermal decomposition of coprecipitated mixtures was detected at a temperature as low as 380°C. The separate formation of MgO and Fe₂O₃ from the thermal decomposition of mechanical mixtures was observed; nevertheless the formation of MgFe₂O₄ through a solid state reaction between the oxides was noted at a temperature as low as 500°C.The Authors wish to thank Dr. L. Petrilli and Mr. F. Dianetti for carrying out the elemental chemical analyses at the Microanalysis Service of the C. N. R. laboratories of the Area della Ricerca di Roma.     

Effect of the composition of aqueous-organic mixtures on the sensitivity of thermal lens measurements

Thermooptical properties of aqueous solutions of methanol, acetonitrile, dimethyl sulfoxide, ethylene glycol, glycerol, 1,4-dioxane, and sucrose were studied, and it was found that the analytical thermal lens signal depends on the nature of the organic component, most of all, on the polarity and molecular size. The sensitivity coefficient of thermal lens measurements is increased to a maximum extent in methanol solutions (by 7.3 times at the concentration 50 vol %) and acetonitrile (by 8.8 times at 26 vol %). It was found that a small concentration of water slightly affects the thermooptical properties of polar organic solvents.     

Fischer-Tropsch synthesis on Ru/NaY catalysts: Effect of the acidity of the zeolite

A series of NaY zeolites with different Si/Al ratios were used to support the Ru catalysts. Both the activity/selectivity of Ru in F–T synthesis and the suppressing of hydrogen may be related to the acid strength of the OH groups present, which is a function of the Si/Al ratio of the zeolite.

---

NaY Si/Al Ru. / Ru -, OH-, Si/Al .

     

Effect of solvent composition on the association behavior of pectin in methanol-water mixtures

Turbidity, small-angle neutron scattering (SANS), and dynamic light scattering measurements have been carried out on semidilute systems of pectin in methanol-water media of various composition ratios. Structural and dynamical properties of pectin dissolved in water-methanol mixtures (case I) are compared with the corresponding conditions when pectin was dissolved in water before the prescribed amounts of methanol were added (case II). The turbidity rises as the percentage of methanol in the mixture increases and this trend is much stronger when the first procedure is used to dissolve pectin. The wavelength dependence of the turbidity indicates that larger association complexes are formed for the samples prepared according to case I. These findings indicate that at a given methanol-water composition, the preparation procedure in case I gives rise to poorer thermodynamic conditions of the system. Local structures probed by SANS experiments do not reveal any significant differences between the systems prepared by the two different procedures. The dynamic light scattering (DLS) results show that increasing methanol concentration in the mixture promotes the formation of association complexes and the disengagement relaxation time of individual chains or clusters is longer at higher percentage of methanol for case II. This can be attributed to stronger entanglement effects in case II. The features from DLS can be rationalized in the framework of the coupling model for constrained and interconnecting systems.     

Retention of Cs on zeolite, bentonite and their mixtures

The sorption behavior of cesium on zeolite and bentonite minerals and their mixtures was studied by means of a batch method and a tracer technique. All experiments were carried out in the presence of CsCl spiked with ¹³⁷Cs and NaCl as a supporting electrolyte in varying concentrations. The distribution coefficients (K _D) did not show significant differences at low Cs⁺ loadings while they decreased in the high loading region. Freundlich and D-R isotherms were applied to the adsorption data of zeolite and bentonite. Adsorption capacities and mean energies calculated from D-R isotherm parameters decreased by increasing ionic strength on both minerals. The identification of the specific uptake sites was attempted on the basis of the Freundlich isotherm. Experimentally observed distribution coefficients of Cs on two mineral mixtures were smaller than theoretically calculated values, except at the highest NaCl concentration.     

硅源对MCM-22分子筛合成及物化性质的影响

在动态水热条件下,研究了硅溶胶、白炭黑、硅酸及硅胶为硅源时对MCM-22分子筛合成及物化性质的影响。以硅溶胶、白炭黑、硅酸三种硅源均可合成出高结晶度且无杂晶的片状MCM-22分子筛,其平均粒径分别为190、220和750 nm。硅源影响分子筛的聚集形态,三种硅源分别形成晶粒分散、晶粒半分散及晶粒聚集形态。三组样品的酸强度分布基本一致,都具有较多的中强酸分布,由硅溶胶和硅酸所得MCM-22分子筛在中强酸范围具有更高的B/L酸比值,以白炭黑合成的分子筛总酸量最高。NMR结果表明,样品中的铝以骨架铝为主,不存在明显的非骨架铝。由于硅胶对合成体系中游离水的吸附作用,水热反应难以发生,不能得到MCM-22分子筛,硅胶作为分子筛合成硅源时需要选择合适的反应条件。     

A hierarchically zeolite Y for the N-heterocyclic compounds synthesis

High activity and selectivity of the hierarchical H-Ymmm zeolite in the synthesis of practically important pyridines (by interaction of C₂–C₄ alcohols with formaldehyde and ammonia, cyclocondensation of acetaldehyde and propanal with ammonia), dialkyl quinolines (by reaction of aniline with aldehydes) and alkyl dihydroquinolines (by reaction of aniline with ketones- acetone, acetophenone) were revealed in the research.The advantages of the micro-meso-macroporous H-Ymmm zeolite over the microporous H-Y zeolite in the synthesis of pyridines and quinolines were demonstrated. In the products formed by the reaction of ethanol with formaldehyde and ammonia, picolines (up to 63%) and lutidine are predominant in H-Ymmm, Pb-H-Ymmm and Fe-H-Ymmm zeolites. The interaction of n-propanol (n-butanol) with formaldehyde and ammonia in the presence of H-Ymmm zeolite with high selectivity produced 3,5-lutidine (up to 90%) or 3,5-diethylpyridine (85%). H-Ymmm zeolite makes it possible to prepare 2-methyl-5-ethylpyridine with 87% selectivity (reaction of acetaldehyde with ammonia) and 2-ethyl-3,5-dimethylpyridine with 58% selectivity (reaction of propanal with ammonia).The synthesis of dialkylquinolines and dialkyltetrahydroquinolines with a total selectivity of 65–73% by the interaction of aniline with C₃–C₅ aldehydes has been carried out. The dihydroquinoline derivatives with the selectivity of up to 70% have been synthesized by the reaction of aniline with ketones (acetone, acetophenone).     

Influence of the synthesis parameters on the thermal behavior of some ZnO–starch composites

Ten ZnO–starch composites were synthesized using a simple precipitation methodology. The IR spectroscopy and XRD investigations reveal the presence of amorphous starch and crystalline ZnO. The obtained composites present a spherical morphology, 5–8 spheres being interconnected into aggregates. The thermal analysis demonstrates that starch decomposition and ZnO thermally induced nucleation and crystal growth depending on the synthesis parameters such as starch processing (dissolution or gelatinization), reaction temperature (80, 90, and 100 °C), reaction time (15 min or 6 h), and applied treatments (heating or ultrasound irradiation).     

Physicochemical properties and thermal behavior of nitrocellulose granules with eutectic mixtures of stabilizers

Journal of Thermal Analysis and Calorimetry - Examinations of two-component mixtures, namely: triphenylamine?+?centralite I (TPA?+?CI) and...