Solvent extraction of cesium into nitrobenzene by using sodium,potassium and rubidium dicarbollylcobaltates in the presence of polypropylene glycol PPG 425

Extraction of microamounts of cesium by nitrobenzene solutions of sodium dicarbollylcobaltate (Na⁺B^?), potassium dicarbollylcobaltate (K⁺B^?) and rubidium dicarbollylcobaltate (Rb⁺B^?) in the presence of polypropylene glycol PPG 425 (L) has been investigated. The equilibrium data have been explained assuming that the complex species ML⁺ (M⁺ = Na⁺, K⁺, Rb⁺, Cs⁺; L = PPG 425) are present in the organic phase. The stability constants of the cationic complex species ML⁺ (M⁺ = Na⁺, K⁺, Rb⁺) in nitrobenzene saturated with water have been determined; they were found to increase in the series of Rb⁺ < K⁺ < Na⁺.     

Adsorption of nitrogen from natural gas by clinoptilolite

Much of world’s natural gas reserves are impure, one of the principal contaminants being nitrogen which makes it unsuitable for application and, hence, its separation is important. In this research, clinoptilolite, the most abundant natural zeolite with an open aluminosilicate framework structure and high internal surface area, was modified by ion exchange process to highly exchanged forms of cations of Na⁺, K⁺ and H⁺. The adsorption of N₂, CH₄ and C₂H₆ on natural clinoptilolite (Cp) and on its cation-exchanged forms (Na-Cp, K-Cp and H-Cp) was studied at 25 °C. The influence of cation exchange on equilibrium adsorption of N₂ showed that selectivity decreased in the order of Cp > Na-Cp > K-Cp and H-Cp has no affinity to nitrogen.     

A Novel Highly Sensitive Zeolite-Based Conductometric Microsensor for Ammonium Determination

Natural zeolite clinoptilolite was successfully applied in the sensing technology for electrochemical detection of ammonium. A novel ammonium-selective sensor was developed based on clinoptilolite, possessing intrinsic ammonium-sieving and ion exchange capacity. The sensor design allowed measurements in both differential mode and requiring no classical reference electrode. The sensor selectivity towards Na⁺, K⁺, Ca²⁺, Mg²⁺, and Al³⁺ was studied. The limit of detection and the dynamic range of the ammonium-selective conductometric microsensor, determined in the phosphate buffer solution, were 1.0 × 10^?8 M and 0–8 mM, respectively. The ammonium sensor presented high operational and storage stability.     

Extraction of cesium into nitrobenzene by using ammonium and thallium dicarbollylcobaltates in the presence of polypropylene glycol PPG 425

Extraction of microamounts of cesium by nitrobenzene solutions of ammonium dicarbollylcobaltate (NH₄ ⁺B^?) and thallium dicarbollylcobaltate (Tl⁺B^?) in the presence of polypropylene glycol PPG 425 (L) has been investigated. The equilibrium data have been explained assuming that the complexes ML⁺ (M⁺ = NH ₄ ⁺ , TI⁺, Cs⁺; L = PPG 425) are present in the organic phase. Furthermore, the stability constants of the cationic complex species NH₄L⁺ and TlL⁺ in nitrobenzene saturated with water have been determined as log β (NH₄L _org ⁺ ) = 4.58 and log β (TlL _org ⁺ ) = 5.27.     

Syntheses and Properties of New Pendant‐armed Calix[4]arene Derivatives as Cesium Selective Ionophore

Two new pendant‐armed calix[4]arene derivatives 5 and 6 have been synthesized. The study of alkali metal picrates extraction indicates that both compounds show preference of cesium cation, compound 6 in 1,3‐alternate conformation has better extractibility for Cs⁺ than compound 5. The coordination behavior of compound 6 with cesium cation was studied by ¹H NMR spectroscopy. The Cs⁺ selective electrode based on compound 6 exhibits a linear, near Nernstian response characteristics, the slope is 56.4 mV/decade in me concentration range of 10^?4—10^?1 mol/L, the selectivity coefficient (logK^pot_Cs.Na) is ?3.39.     

Fast concentration of dissolved forms of cesium radioisotopes from large seawater samples

The method developed for cesium concentration from large freshwater samples was tested and adapted for analysis of cesium radionuclides in seawater. Concentration of dissolved forms of cesium in large seawater samples (about 100 L) was performed using composite absorbers AMP-PAN and KNiFC-PAN with ammonium molybdophosphate and potassium–nickel hexacyanoferrate(II) as active components, respectively, and polyacrylonitrile as a binding polymer. A specially designed chromatography column with bed volume (BV) 25 mL allowed fast flow rates of seawater (up to 1,200 BV h^?1). The recovery yields were determined by ICP-MS analysis of stable cesium added to seawater sample. Both absorbers proved usability for cesium concentration from large seawater samples. KNiFC-PAN material was slightly more effective in cesium concentration from acidified seawater (recovery yield around 93 % for 700 BV h^?1). This material showed similar efficiency in cesium concentration also from natural seawater. The activity concentrations of ¹³⁷Cs determined in seawater from the central Pacific Ocean were 1.5 ± 0.1 and 1.4 ± 0.1 Bq m^?3 for an offshore (January 2012) and a coastal (February 2012) locality, respectively, ¹³⁴Cs activities were below detection limit (<0.2 Bq m^?3).     

Investigation of cesium uptake from aqueous solutions using new titanium phosphates ion-exchangers

The uptake of cesium from aqueous solutions (pH 5) using titanium phosphates was investigated in the absence and presence of background electrolyte (0.1 M NaNO₃) using a batch technique. The determination of cesium was performed by gamma spectroscopy using ¹³⁷Cs as tracer. The obtained sorption isotherms could be satisfactorily reproduced by a Langmuir sorption equation. The maximum uptake capacity values (q _max) calculated fitting the experimental data by this equation were 167 and 118 mg/g for solutions of initial pH 5 in the absence and presence of background electrolyte. Kinetics data obtained at 293, 308 and 323 K could satisfactorily reproduced by the pseudo-second order equation. It was demonstrated that the new synthesized materials can remove considerable amounts of cesium from aqueous solutions and ion exchange is considered to be the principal mechanism for cesium removal. Toxicity characteristic leaching procedure and desorption tests provided data about the application of the sorbents in environmental remediation.     

Assessment of Potassium Zinc Ferrocyanide as an Alkali-Metal Ion-Exchanger in Ion-Selective Electrodes

Abstract

Silicone rubber membranes containing potassium zinc ferrocyanide have been assessed as ion-selective electrode sensors for the determination of alkali metal ions. The slope of the calibration graph for potassium ion is 59 mV per decade change in concentration within the concentration range 5 × 10^?4 to 10^?1 M at 25°C. Selectivity constants (K_K + _/M+)are 9. 5, Cs⁺; 3. 3, Rb⁺; 0. 025, Na⁺; 0. 003, Li⁺; and 1.8, NH₄ ⁺, calculated from potential data obtained at 10^?1 M concentrations of each ion separately. Similar membranes prepared from PVC responded similarly with a slight improvement in selectivity.     

Polymeric membrane coated graphite cesium selective electrode based on 4′,4″(5′) di–tert-butyl di-benzo-18-crown-6

A new PVC membrane coated graphite electrode for cesium ion based on 4′,4″(5′)di–tert-butyl di-benzo-18-crown-6 (DTBDB18C6) as ionophore was prepared. The electrode shows a near Nernstian response of 57.0 ± 1.8 mV decade^?1 over a wide activity range of 6.0 × 10^?6–1.0 × 10^?1 mol L^?1 with a limit of detection 4.0 × 10^?6 mol L^?1. The proposed electrode is suitable for use in aqueous solution in the pH range of 3.0–9.5. It has a fast response time of 10 s and can be used for at least 1 month without any considerable divergence in potential. The selectivity coefficients for Cs⁺ ion with respect to ammonium, alkali, alkaline earth and some selected transition metal ions were determined and showed a superior selectivity over Li⁺, Na⁺ and alkaline earth metal ions. The new electrode was applied for determination of Cs⁺ in spiked tap water. The electrode was also used as indicator electrode in potentiometric titration of Cs⁺ with sodium tetraphenyl borate.     

Removal of some radionuclides from contaminated solution using natural clay: bentonite

Clays and specially bentonite are widely used as natural adsorbents for wastewater treatment and as a barrier in landfills to prevent the contamination of subsoil and groundwater by leachates containing radioactive materials. The adsorption of four radionuclides, ¹³⁴Cs(I), ⁹⁰Sr(II), ¹³³Ba(II) and ¹⁵²Eu(III) by an Egyptian bentonite (Bent) and its modified Na⁺ form (Na-Bent) collected from a deposit within Alexandria governorate was investigated as a function of different parameters. The batch equilibrium technique was used and the kinetic results showed that the equilibrium was mostly reached within 10 min and the kinetic data fit well to the pseudo-second order model. The Langmuir model fits well the experimental data of all metals adsorption on Bent and Na-Bent except for adsorption of ¹³³Ba on Bent, while ¹⁵²Eu adsorption on Na-Bent fits better to the Freundlich model rather than to the Langmuir. Both Bent and Na-Bent fit well to the D-R model with adsorption energy of E > 8 kJ mol^?1 that means that the adsorption reaction is expected to be controlled by both cation exchange and surface complexation reactions. At lower concentrations, the values of distribution coefficient (K _d), follow the order of ¹⁵²Eu > ⁹⁰Sr > ¹³⁴Cs > ¹³³Ba for Bent and Na-Bent. The K _d of ¹⁵²Eu is higher than that of ¹³⁴Cs in Bent up to 150 mg L^?1. This order changes at higher concentration where the K _d of ¹³⁴Cs becomes higher than ¹⁵²Eu after 150 mg L^?1 for Bent and after 200 mg L^?1 for Na-Bent. Na-Bent is preferred than Bent for the uptake of ⁹⁰Sr and ¹³⁴Cs especially at high concentration.     

Acylpyrazolone Modified Glassy Carbon Electrode Effect on the Electrochemical Behavior of Tyrosine

Abstract

This work demonstrates the electrochemical behavior of the 1-phenyl-3-methyl-4-(α-furoyl)-pyrazolone-5 (HPMαFP) modified glassy carbon electrode (HPMαFP/GCE) by a dropletting method. Tyrosine (Tyr) was detected at the HPMαFP/GCE by cyclic voltammetry. The mechanism and the best condition of electrode reaction were studied. The results indicate Tyr has an excellent electrochemical response at HPMαFP/GCE; under optimized experimental conditions, the peak current is proportional to the concentration of Tyr over a wide range. The linear regression equation at HPMαFP/GCE is I_Pa (µA) = 1.01134 + 0.96716 C (µmol · L^?1) (r = 0.99914). The low detection limit is 1.6 × 10^?7 mol · L^?1. The modified electrode exhibited high sensitivity, good selectivity, and reproducibility, and it is easy to prepare.     

Influence of the exchangeable cations on SO<Subscript>2</Subscript> adsorption capacities of clinoptilolite-rich natural zeolite

The sulfur dioxide adsorption on clinoptilolite-rich tuff from Bigadiç region of Western of Turkey and its modified forms (Na⁺, K⁺, Ca²⁺ and Mg²⁺) have been studied at 273 K and 293 K up to 100 kPa. The structural properties of clinoptilolites were studied by X-ray diffraction (XRD) and Fourier transform infrared (FT-IR). The quantitative XRD analysis demonstrated that the Natural-B sample is mainly constituted by clinoptilolite (80–85%) with minor contents of quartz (7–8%), feldspar (5–6%) and mica-illit (4–5%). It was found out that the adsorption capacity and the affinity of SO₂ with clinoptilolite samples depended mainly on the type of exchanged cations and decreased as Na-B > K-B > Mg-B > Natural-B > Ca-B for both temperature. These results show that clinoptilolite-rich zeolites are considered potentially good adsorbents for SO₂ removal.     

Complexation of the cesium cation with nonactin: extraction and DFT study

From extraction experiments and γ-activity measurements, the extraction constant corresponding to the equilibrium Cs⁺(aq) + A^?(aq) + 1(nb) ? 1·Cs⁺(nb) + A^?(nb) taking place in the two-phase water–nitrobenzene system (A^? = picrate, 1 = nonactin; aq = aqueous phase, nb = nitrobenzene phase) was evaluated as log K _ex (1·Cs⁺,A^?) = 2.8 ± 0.1. Further, the stability constant of the 1·Cs⁺ complex in nitrobenzene saturated with water was calculated for a temperature of 25 °C: log β _nb (1·Cs⁺) = 4.7 ± 0.1. Finally, by using quantum–mechanical DFT calculations, the most probable structure of the resulting cationic complex species 1·Cs⁺ was derived.     

Kinetics and mechanism of the redox reaction between malachite green and iron(III) in aqueous and micellar media

The kinetics of the oxidation of malachite green (MG⁺) by Fe(III) were investigated spectrophotometrically by monitoring the absorbance change at 618 nm in aqueous and micellar media at a temperature range 20–40 °C; I = 0.10 mol dm^?3 for [H⁺] range (2.50–15.00) × 10^?4 mol dm^?3. The rate of reaction increases with increasing [H⁺]. The reaction was carried out under pseudo-first-order conditions by taking the [Fe(III)] (>10-fold) the [MG⁺]. A mechanism of the reaction between malachite green and Fe(III) is proposed, and the rate equation derived from the mechanism was consistent with the experimental rate law as follows: Rate = (k ₄ + K ₁ k ₅[H⁺]) [MG⁺][Fe(III)]. The effect of surfactants, such as cetyltrimethylammonium bromide (CTAB, a cationic surfactant) and sodium dodecylsulfate (SDS, an anionic surfactant), on the reaction rate has been studied. CTAB has no effect on the rate of reaction while SDS inhibits it. Also, the effect of ligands on the reaction rate has been investigated. It is proposed that electron transfer proceeds through an outer-sphere mechanism. The enthalpy and the entropy of the activation were calculated using the transition state theory equation.     

Adsorption of La,Eu and Lu on raw and modified red clay

Adsorption of La, Eu, and Lu on red clay was studied in an initial concentration range of 10^?4–10^?3 mol/dm³ and a pH range of 2–10. Among the different forms of red clay: T-clay (thermally modified), R-clay (raw, unmodified), Na-clay (sodium form), H-clay (acid form), and HDTMA-clay (surfactant-modified form), T-clay was found to be the most effective adsorbent of the lanthanides studied. The adsorption/desorption isotherms, i.e. log K _d versus log c _eq dependencies, had a linear character. Among the investigated lanthanides, Eu was most strongly bound by the clay surface and, therefore, parameters a (slopes of the lines log K _d = alog c _eq + b) of Eu were the highest compared to those for La and Lu. Desorption isotherms were located above adsorption isotherms, which resulted from chemiadsorption of the investigated lanthanides. Changes in lanthanide adsorption with pH were successfully modelled based on the molar fractions of Ln³⁺, LnOH²⁺, LnCO₃ ⁺, and Ln(CO₃) ₂ ^? species in the aqueous phase [Ln—lanthanide(III)].     

Electrocatalytic Oxidation and Voltammetric Determination of Hydrazine in Industrial Boiler Feed Water Using a Cobalt Phthalocyanine-modified Electrode

Abstract

A carbon paste electrode modified with cobalt phthalocyanine (CPECoPc) was developed and applied to the determination of hydrazine [N₂H₄] in industrial boiler feed water. The CPECoPc exhibited good electrocatalytical activity for hydrazine oxidation at pH 13. A linear correlation was obtained between anodic peak current (I_ap) and hydrazine concentration in the range of 1.25 × 10^?4 to 9.80 × 10^?4 mol L^?1, fit by the equation I_ap = 1.47 + 4.90 × 10⁵ [N₂H₄] with a correlation coefficient of 0.9967. A detection limit of 7.35 × 10^?5 mol L^?1 was obtained. Recovery of hydrazine from three samples ranged between 99.0% and 102.9%. The modified electrode showed no interference by cations commonly present in boiler water, such as K⁺, Na⁺, Ca²⁺, Mg²⁺, Al³⁺, Pb²⁺, and Zn²⁺. The results obtained for hydrazine in boiler water using the proposed modified electrode are in agreement with the data obtained by a standard spectrophotometric method, at the 95% confidence level.     

Experimental investigation of radiocesium sorption on ceramic clay using a batch method

In this study, radiocesium sorption on ceramic clay was investigated as a function of particle size and initial ¹³⁷Cs concentration using a batch method. Ceramic clay samples taken from the Sö?üt(?nisar) clay deposit were composed of kaolinite, dickite and quartz. The equilibrium time and the liquid–solid ratio were determined as 60 min and 250 mL g^?1, respectively. The distribution coefficients (K _d) for variable liquid–solid ratio and the percentage adsorption (P _Ad) were calculated. The values of K _d and P _Ad ranged from 483 to 3165 mL g^?1 and 34–93%, respectively. The K _d and P _Ad values increased with increasing particle size, but decreased with increasing initial concentration. The sorption data were interpreted in terms of a Langmuir isotherm. The results indicated that the Sö?üt(?nhisar) ceramic clay has good sorption capacity for cesium.     

Extraction and theoretical study on the complexation of the strontium cation with beauvericin

From extraction experiments and γ-activity measurements, the extraction constant corresponding to the equilibrium Sr²⁺(aq) + 2A^?(aq) +1(nb) ? 1·Sr²⁺(nb) + 2A^?(nb) taking place in the two-phase water–nitrobenzene system (A^? = picrate, 1 = beauvericin; aq = aqueous phase, nb = nitrobenzene phase) was evaluated as log K _ex(1·Sr²⁺,2A^?) = ?0.6 ± 0.1. Further, the stability constant of the 1·Sr²⁺ complex in nitrobenzene saturated with water was calculated for a temperature of 25 °C: log β _nb(1·Sr²⁺) = 8.5 ± 0.1. Finally, by using quantum-mechanical DFT calculations, the most probable structure of the resulting cationic complex 1·Sr²⁺ was derived.     

Thermodynamics of cesium complexes formation with 18-crown-6 in ionic liquids

Thermodynamic data for cesium complexes formation with 18-crown-6 (18C6, L) [Cs(18C6)]⁺ in N-butyl-4-methyl-pyridinium tetrafluoroborate ([BMPy][BF₄], I), in 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF₄], II) and in 1-butyl-3-methylimidazolium dicyanamide ([BMIM][N(CN)₂], III) were measured with NMR ¹³³Cs technique at 23–50 °C. The stability of cesium complex in RTILs is estimated to be in the range between water and DMFA. Stability constants for [Cs(18C6)]⁺ are found to decrease as temperature is increasing. The following values for lgK(Cs+L) and ΔH(Cs+L) at 23 °C are determined: 2.6 (0.3), ?47(1) kJ/mol (RTIL I); 2.8(0.3), ?80(3) kJ/mol (RTIL II) and 3.03 (0.08), ?47(2) kJ/mol (RTIL III). It is demonstrated that enthalpy change promotes complex formation while the corresponding change of entropy is negative and provides decomposition of [Cs(18C6)]⁺.     

Low-temperature thermodynamics of Ln(Me2dtc)3(C12H8N2) (Me2dtc = dimethyldithiocarbamate, Ln = La, Pr, Nd, Sm)

The heat capacities of Ln(Me₂dtc)₃(C₁₂H₈N₂) (Ln = La, Pr, Nd, Sm, Me₂dtc = dimethyldithiocarbamate) have been measured by the adiabatic method within the temperature range 78–404 K. The temperature dependencies of the heat capacities, C _p,m [La(Me₂dtc)₃(C₁₂H₈N₂)] = 542.097 + 229.576 X ? 27.169 X ² + 14.596 X ³ ? 7.135 X ⁴ (J K^?1 mol^?1), C _p,m [Pr(Me₂dtc)₃(C₁₂H₈N₂)] = 500.252 + 314.114 X ? 17.596 X ² ? 0.131 X ³ + 16.627 X ⁴ (J K^?1 mol^?1), C _p,m [Nd(Me₂dtc)₃(C₁₂H₈N₂)] = 543.586 + 213.876 X ? 68.040 X ² + 1.173 X ³ + 2.563 X ⁴ (J K^?1 mol^?1) and C _p,m [Sm(Me₂dtc)₃(C₁₂H₈N₂)] = 528.650 + 216.408 X ? 16.492 X ² + 12.076 X ³ + 4.912 X ⁴ (J K^?1 mol^?1), were derived by the least-squares method from the experimental data. The heat capacities of Ce(Me₂dtc)₃(C₁₂H₈N₂) and Pm(Me₂dtc)₃(C₁₂H₈N₂) at 298.15 K were evaluated to be 617.99 and 610.09 J K^?1 mol^?1, respectively. Furthermore, the thermodynamic functions (entropy, enthalpy and Gibbs free energy) have been calculated using the obtained experimental heat capacity data.