Heat release during the hydration of calcinated α-C<Subscript>2</Subscript>SH and its mixture with killalaite

In this work, the influence of the mineral composition of the synthesized calcium silicate hydrates on their hydraulic activity after thermal treatment was determined. Primary mixture, consisting of quartz sand and burnt limestone (CaO/SiO₂ = 2), was treated hydrothermally with NaOH additive at 200 °C. It was determined that α-C₂SH prevailed in the product after 4 h of the synthesis. The results of DSC and XRD analysis revealed that α-C₂SH was partially decomposed after 12 h of the synthesis and newly formed compounds were identified—killalaite, portlandite and C–S–H. The products of 4 and 12 h synthesis were treated thermally at temperatures between 450 and 1000 °C. It was determined that dellaite and x-C₂S formed already at 450 °C, β-C₂S at 600 °C and α′_L-C₂S at 800 °C when the 4 h synthesis product, in which α-C₂SH prevailed, was treated thermally. On the other hand, killalaite remained stable up to 600 °C, and the temperature values, at which mentioned calcium silicates formed, increased in case of a 12 h synthesis product. Heat flow values of the main hydration reaction and total heat release exceeded 3.1 mW g^?1 and 140 J g^?1 accordingly in case of the samples in which α-C₂SH prevailed. However, increase in the thermal treatment temperature resulted in a decrease in the mixtures hydraulic activity. It was proved that killalaite formation in the product of the 12 h hydrothermal synthesis vividly decreases its hydraulic activity after the thermal treatment in the temperature range of 450–1000 °C. No increment in the heat flow values that could be attributed to the main hydration reaction (acceleration period) was witnessed in all the curves of the heat flow analysis in this case.     

Thermal, spectral and AFM studies of calcium silicate hydrate-polymer nanocomposite material

A non-ionic polymer (poly(vinyl alcohol) (PVA)) has been incorporated into the inorganic layers of calcium silicate hydrate (C–S–H) during precipitation of quasicrystalline C–S–H from aqueous solution. C–S–H and a C–S–H-polymer nanocomposite (C–S–HPN) material were synthesized and characterized by X-ray fluorescence (XRF), energy dispersive spectroscopy (EDS), ²⁹Si magic angle spinning nuclear magnetic resonance (²⁹Si MAS NMR) and ¹³C cross-polarization nuclear magnetic resonance (¹³C CP NMR) spectroscopy, atomic force microscopy (AFM), thermal conductivity, thermogravimetric analysis (TG) and differential thermal analysis (DTA). Thermal conductivity of PVA, C–S–H and C–S–HPN material was studied in the temperature range 25–50°C. C–S–HPN materials exhibited the highest thermal conductivity at 25 and 50°C. The thermal conductivity increases from 25 to 50°C are 7.03, 17.46 and 14.85% for PVA, C–S–H and C–S–HPN material, respectively. Three significant decomposition temperature ranges were observed on the TG curve of C–S–HPN material.     

Effect of water release on thermal properties of polyaniline

Conducting polyaniline (PANI) was studied by thermal expansion measurement, thermogravimetric analysis and by electrical conductivity measurement. Relative elongation and coefficient of thermal expansion (CTE) were determined from room temperature to 60 °C. Various temperature profiles were used. During heating, the treatment of samples at a constant temperature higher than the room temperature, or evacuation, water was released from the samples. Water release was detected by mass and thermogravimetric analysis. Water release was connected with shrinkage of the PANI samples and apparent negative CTE in the first thermal cycle. In the following thermal cycles, it increased and reached a positive value. CTE of PANI attained values in the range of ?30 × 10^?6 K^?1 up to 20 × 10^?6 K^?1 in dependence on water content in the sample before measurement and on experimental conditions of measurement. Irreversible shrinkage of the polymer was the largest in the first thermal cycle. Water release exhibited a strong time and temperature dependence, and it was only partially reversible. The electrical conductivity was measured by a four-point van der Pauw method. Relative electrical conductivity decreased with amounts of water release. Relative decrease of electrical conductivity reached as far as 20% after evacuation 7 h at the room temperature.     

Environmentally benign sol–gel derived nanocrystalline rod shaped calcium doped cerium phosphate yellow-green pigment

Nanocrystalline rod shaped calcium doped cerium phosphate yellow-green pigment particles having an average length of ~100 nm and aspect ratio 10 even after calcination at 600 °C have been realized through an aqueous sol–gel process. The morphology, particle size and identification of the phase are determined by using different analytical tools such as transmission electron microscopy (TEM), photon correlation spectroscopy (PCS), Fourier-transform IR (FTIR) and X-ray diffraction (XRD). Brunauer–Emmett–Teller (BET) nitrogen adsorption analysis showed the pigment particles are mesoporous texture having specific surface area 42 m² g^?1 and average pore size 153 Å. Thermogravimetric (TG) analysis is used to explain the thermal phase stability of the pigment. UV–Visible spectroscopy and colorimetric analysis are also done. The typical yellow-green color has been obtained even after heating to as low as 600 °C, which is 300 °C lesser than reported. Systematic study on synthesis and effect of temperature on color are presented.     

Preparation and characterization of blended solid polymer electrolyte 49% poly(methyl methacrylate)-grafted natural rubber:poly(methyl methacrylate)–lithium tetrafluoroborate

The preparation and characterization of blended solid polymer electrolyte 49% poly(methyl methacrylate)-grafted natural rubber (MG49):poly(methyl methacrylate) (PMMA) (30:70) were carried out. The effect of lithium tetrafluoroborate (LiBF₄) concentration on the chemical interaction, structure, morphology, and room temperature conductivity of the electrolyte were investigated. The electrolyte samples with various weight percentages (wt.%) of LiBF₄ salt were prepared by solution casting technique and characterized by Fourier transform infrared spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrochemical impedance spectroscopy. Infrared analysis demonstrated that the interaction between lithium ions and oxygen atoms occurred at symmetrical stretching of carbonyl (C=O) (1,735 cm^?1) and asymmetric deformation of (O–CH₃) (1,456 cm^?1) via the formation of coordinate bond on MMA structure in MG49 and PMMA. The reduction of MMA peaks intensity at the diffraction angle, 2θ of 29.5° and 39.5° was due to the increase in weight percent of LiBF₄. The complexation occurred between the salt and polymer host had been confirmed by the XRD analysis. The semi-crystalline phase of polymer host was found to reduce with the increase in salt content and confirmed by XRD analysis. Morphological studies by SEM showed that MG49 blended with PMMA was compatible. The addition of salt into the blend has changed the topological order of the polymer host from dark surface to brighter surface. The SEM analyses supported the enhancement of conductivity with the addition of salt. The conductivity increased drastically from 2.0 to 3.4?×?10^?5 S cm^?1 with the addition of 25 wt.% of salt. The increase in the conductivity was due to the increasing of the number of charge carriers in the electrolyte. The conductivity obeys Arrhenius equation in higher temperature region from 333 to 373 K with the pre-exponential factor σ _o of 1.21?×?10^?7 S cm^?1 and the activation energy E _a of 0.46 eV. The conductivity is not Arrhenian in lower temperature region from 303 to 323 K.     

A comparison of sulfur loading method on the electrochemical performance of porous carbon/sulfur cathode material for lithium–sulfur battery

To get a high sulfur loaded porous carbon/sulfur cathode material with an excellent performance, we investigated four different sulfur loading treatments. The samples were analyzed by the Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD) patterns, thermal gravimetric analysis (TGA), and scanning electron microscopy (SEM). We proved that it is more effective to introduce the sulfur into the pores of porous carbon at 300 °C than at 155 °C. Especially, the porous carbon/sulfur composite heated in a sealed reactor at 300 °C for 8 h presents a fine sulfur load with sulfur content of 78 wt.% and exhibits an excellent electrochemical performance. The discharge capacity is 760, 727, 744, 713, and 575 mAh g^?1 of sulfur at a current density of 80, 160, 320, 800, and 1,600 mA g^?1 based on the sulfur/carbon composite, respectively. What is more, there is almost no decay at the current density of 800 mA g^?1 for 50 cycles and coulombic efficiency remains over 95 %.     

Characterization of crystalline and amorphous content in pharmaceutical solids by dielectric thermal analysis

Morphological and thermodynamic transitions in drugs as well as their amorphous and crystalline content in the solid state have been distinguished by thermal analytical techniques, which include dielectric analysis (DEA), differential scanning calorimetry (DSC), and macro-photomicrography. These techniques were used successfully to establish a structure versus property relationship with the United States Pharmacopeia standard set of active pharmaceutical ingredient (API) drugs. A distinguishing method is the DSC determination of the amorphous and crystalline content which is based on the fusion properties of the specific drug and its recrystallization. The DSC technique to determine the crystalline and amorphous content is based on a series of heat and cool cycles to evaluate the drugs ability to recrystallize. To enhance the amorphous portion, the API is heated above its melting temperature and cooled with liquid nitrogen to ?120 °C (153 K). Alternatively a sample is program heated and cooled by DSC at a rate of 10 °C min^?1. DEA measures the crystalline solid and amorphous liquid API electrical ionic conductivity. The DEA ionic conductivity is repeatable and differentiates the solid crystalline drug with a low conductivity level (10^?2 pS cm^?1) and a high conductivity level associated with the amorphous liquid (10⁶ pS cm^?1). The DSC sets the analytical transition temperature range from melting to recrystallization. However, analysis of the DEA ionic conductivity cycle establishes the quantitative amorphous and crystalline content in the solid state at frequencies of 0.10–1.00 Hz and to greater than 30 °C below the melting transition as the peak melting temperature. This describes the “activation energy method.” An Arrhenius plot, log ionic conductivity versus reciprocal temperature (K^?1), of the pre-melt DEA transition yields frequency dependent activation energy (E _a, J mol^?1) for the complex charging in the solid state. The amorphous content is inversely proportional to the E _a where the E _a for the crystalline form is higher and lower for the amorphous form with a standard deviation of ±2%. There was a good agreement between the DSC crystalline melting, recrystallization, and the solid state DEA conductivity method with relevant microscopic evaluation. An alternate technique to determine amorphous and crystalline content has been established for the drugs of interest based on an obvious amorphous and crystalline state identified by macro-photomicrography and compared to the conductivity variations. This second “empirical method” correlates well with the “activation energy” method.     

Electrical conductivity of titanium pyrophosphate between 100 and 400 °C: effect of sintering temperature and phosphorus content

The synthesis of titanium pyrophosphate is carried out, and the material is sintered at different temperatures between 370 and 970 °C. Yttrium is added during the synthesis to act as acceptor dopant, but it is mainly present in the material in secondary phases. The conductivity is studied systematically as a function of sintering temperature, pH₂O, pO₂, and temperature (100–400 °C). Loss of phosphorus upon sintering above 580–600 °C is confirmed by energy dispersive spectroscopy and combined thermogravimetry and mass spectrometry. The conductivity decreases with increasing sintering temperature and decreasing phosphorus content. The highest conductivity is 5.3?×?10^?4 S cm^?1 at 140 °C in wet air (pH₂O?=?0.22 atm) after sintering at 370 °C. The conductivity is higher in wet atmospheres than in dry atmospheres. The proton conduction mechanism is discussed, and the conductivity is attributed to an amorphous secondary phase at the grain boundaries, associated with the presence of excess phosphorus in the samples. A contribution to the conductivity by point defects in the bulk may explain the conductivity trend in dry air and the difference in conductivity between oxidizing and reducing atmospheres at 300–390 °C. Slow loss of phosphorus by evaporation over time and changes in the distribution of the amorphous phase during testing are suggested as causes of conductivity degradation above 220 °C.     

Electrospun cellulose acetate/poly(vinylidene fluoride) nanofibrous membrane for polymer lithium-ion batteries

The membranes for gel polymer electrolyte (GPE) for lithium-ion batteries were prepared by electrospinning a blend of poly(vinylidene fluoride) (PVdF) with cellulose acetate (CA). The performances of the prepared membranes and the resulted GPEs were investigated, including scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), X-ray diffraction (XRD), porosity, hydrophilicity, electrolyte uptake, mechanical property, thermal stability, AC impedance measurements, linear sweep voltammetry, and charge–discharge cycle tests. The effect of the ratio of CA to PVdF on the performance of the prepared membranes was considered. It is found that the GPE based on the blended polymer with CA:PVdF =2:8 (in weight) has an outstanding combination property-strength (11.1 MPa), electrolyte uptake (768.2 %), thermal stability (no shrinkage under 80 °C without tension), and ionic conductivity (2.61 × 10^?3 S cm^?1). The Li/GPE/LiCoO₂ battery using this GPE exhibits superior cyclic stability and storage performance at room temperature. Its specific capacity reaches up to 204.15 mAh g^?1, with embedded lithium capacity utilization rate of 74.94 %, which is higher than the other lithium-ion batteries with the same cathode material LiCoO₂ (about 50 %).     

Preparation and characterization of electrospun LiFePO4/carbon complex improving rate performance at high C-rate

LiFePO₄/carbon complexes were prepared by electrospinning to improve rate performance at high C-rate and their electrochemical properties were investigated to be used as a cathode active material for lithium ion battery. The LiFePO₄/carbon complexes were prepared by the electrospinning method. The prepared samples were characterized by SEM, EDS, XRD, TGA, electrometer, and electrochemical analysis. The LiFePO₄/carbon complexes prepared have a continuous structure with carbon-coated LiFePO₄ and the LiFePO₄ in LiFePO₄/carbon complex has improved thermal stability from carbon coating. The conductivity of LiFePO₄/carbon complex heat-treated at 800 °C is measured as 2.23 × 10^?2 S cm^?1, which is about 10⁶–10⁷ times more than that of raw LiFePO₄. The capacity ratio of coin cell manufactured from raw LiFePO₄ is 40%, whereas the capacity ratio of coin cell manufactured from LiFePO₄/carbon complex heat-treated at 800 °C is 61% (10 C/0.1 C). The improved rate performance of LiFePO₄/carbon complex heat-treated at 800 °C is due to the carbon coating and good electrical connection.     

Thermal analysis of a white calcium bentonite

A white calcium bentonite (CaB) taken from Çaml?dere (Ankara, Turkey) region was heated at various temperatures between 100 and 1100 °C for 2 h. The mineralogy of the CaB was determined as calcium smectite (CaS), metahalloysite (MH), opal-A (OA), opal-CT (OCT), quartz (Q), feldspar (F), and calcite (C) using the X-ray diffraction patterns of the natural CaB and its heated samples. Besides the XRD patterns, the thermogravimetry, differential thermal analysis, and low-temperature nitrogen adsorption (N₂-AD) data show that the CaS lose adsorbed and hydration water up to 300 °C, dehydroxylation takes place between 300 and 750 °C, and then the 2:1 layer structure completely collapses above 900 °C. The activation energies for the dehydration and dehydroxylation were calculated as 7636 and 48838 J mol^?1, respectively, from the TG data using Coats and Redfern method. The specific surface area (S) and specific micro–mesopore volume (V) obtained from N₂-AD data were 44 m² g^?1 and 0.100 cm³ g^?1 for the natural CaB. S and V reach their maxima of 105 m² g^?1 and 0.155 cm³ g^?1, respectively, at 300 °C, remain approximately constant as the temperature increases up to 700 °C and then decrease almost in parallel with each other, reaching their minima at 900 °C. This indicates that the S and V values increase gradually during dehydration and dehydroxylation of the CaS.     

An innovative CaSiO<Subscript>3</Subscript> dielectric material from eggshells by sol–gel process

Calcium silicate (CaSiO₃), wollastonite, with a molar ratio of CaO:SiO₂ of 1:1, was synthesized by a sol–gel process and sintered at 1,100°C for 1 h. The synthesis of calcium silicate was carried out using chicken eggshells as the starting material possessing several advantages such as low cost, high purity, and less moisture sensitivity, when compared with those obtained from metal alkoxide precursors via the sol–gel process. The CaSiO₃ samples have the triclinic or anorthic phase formations and good electrical properties. The dielectric constant and electrical conductivity are 62.59 ± 0.44 and 8.0052 × 10⁻⁴ (Ω.m)⁻¹, respectively, at 25°C and 1 MHz. The transmission electron microscopy (TEM) images of the samples show a good dispersion and uniform particles with an average diameter of about 0.5 nm. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), and Simultaneous thermal analysis (STA) were used to verify the synthesis.     

Quantitative analysis of phase transition of heated Portland cement paste

This paper studies Portland cement paste heated up to different temperatures ranging from 105 to 1,000 °C by X-ray diffraction. The heated cement paste samples are kept isothermal in furnace for 6 h and cooled down to 100 °C. Then the samples are picked out and grinded into fine powders. 10 % Corundum is blended with cement paste powders as an internal standard. Quantitative phase analysis of cement paste samples is performed by Rietveld method. With the addition of a crystalline standard, the mass fractions of all crystalline phases as well as amorphous calcium silicate hydrate (C–S–H) are determined. The Rietveld analysis results are compared with independent measurements of the same material by thermal analysis (TG/DSC). The phase transition of Portland cement paste is discussed. An empirical relationship between the dehydration degree of C–S–H and the crystallization degree of C–S–H is derived.     

Preparation and investigation on tetradecanol and myristic acid/cellulose form-stable phase change material

In this paper, a novel form-stable phase change material (FS PCM) was prepared by incorporating the eutectic mixture of tetradecanol (TD) and myristic acid (MA) into the hydroxylpropyl methyl cellulose (HPMC). HPMC is used as support material, and the eutectic mixture is used as phase change material. The Fourier-transform infrared spectroscopy (FT-IR), X-ray diffractometer (XRD) and scanning electron microscopy (SEM) were used to study the chemical structure, crystallization behavior and morphology of the FS PCM, respectively. FT-IR, XRD and SEM showed that the TD–MA was distributed uniformly in HPMC by physical interaction. Specific surface area (BET) and pore size analysis determined the pore characteristics of the composite, and the results showed the porosity of HPMC. The thermal properties, thermal stability and thermal reliability were detected by differential scanning calorimetry (DSC), thermogravimetric analysis (TG), thermal cycling test and leakage test. The TG, DSC and leakage analysis results revealed that the absorption of eutectic mixture into HPMC is nearly 50% and without seepage from the composite. The peak temperatures of melting and solidifying were 34.61 and 31.09 °C, and latent heat was 102.11/84.58 J g^?1 by DSC. TG and cycling experiment detected that the FS PCM showed good thermal stability and reliability performance.     

Preparation of the Monolith of Hierarchical Macro‐/Mesoporous Calcium Silicate Ultrathin Nanosheets with Low Thermal Conductivity by Means of Ambient‐Pressure Drying

Calcium silicate monolith was prepared by the hydrothermal reaction of a slurry of SiO₂, calcium hydroxide, and surfactant (OP‐10) obtained by high‐energy ball milling, followed by drying at ambient pressure. By using this strategy, the shrinkage due to the collapse of pores during the drying of porous materials, which is a commonly observed phenomena, was successfully avoided. It has a unique microstructure of hierarchical macro‐/mesoporous ultrathin calcium silicate nanosheets with a layered gyrolite crystalline structure. Very interestingly, the calcium silicate nanosheets can be peeled off to give a single‐layer nanosheet (1.23 nm) of gyrolite by ultrasonication. The monolith has a low apparent density (0.073 g cm^?3) and low thermal conductivity (0.0399 W K^?1 m^?1). The reasons behind why the formation of the unique hierarchical macro‐/mesoporous ultrathin nanosheets avoids shrinkage during the hydrothermal reaction and drying, and considerably decreases the thermal conductivity, is discussed.     

Thermal performance and flammability of phase change material for medium and elevated temperatures for textile application

Thermal energy storage and insulation have potential applications in many fields such as incorporating phase change material (PCM) in textile materials for insulation in medium and elevated temperatures when the high heat flux 80–84 kW m^?2 results from flashover conditions in a firefighting environment. The feasibility of four selected PCMs is considered in this research. The lack of guidance of hazards of sugar alcohols as a potential PCM is analyzed from molecular structure point of view. The results showed that isomerism of PCMs has a tremendous influence on the flash point of PCMs and hence flammability. Differential scanning calorimeter thermal performance showed that the four candidate PCMs have a remarkable melting temperature and enthalpy of fusion. Different heating rates were observed (1.11, 0.43, and 0.095 %) in the melting temperatures: at 50, 20, and 5 °C·min^?1, respectively. Smaller heating rates are preferable for accurate data. PCMs also undergo degradation due to the high-temperature exposure. Although dulcitol and d-mannitol have the same molecular formula, dulcitol requires higher temperature for degradation than does d-mannitol, and this difference is around 26.08 K. The analysis of results showed that the position of functional group has tremendous influence on the thermal performance. Salt hydrates have a multistep thermal degradation and the lowest loss of mass compared with sugar alcohols. This is because salt hydrates have higher intermolecular forces, which make them undergo high thermal endothermic and exothermic processes.     

Temperature dependency of thermal conductivity of solid phases for fatty acids

Thermal conductivity variations with temperature of solid phases for lauric acid (LA), myristic acid (MA), pivalic acid (PA), and stearic acid (SA) have been measured with radial heat-flow method. Temperature dependencies of the thermal conductivity for same organic materials have been obtained by linear regression analysis. From graphs of thermal conductivity versus temperature, the thermal conductivity of solid phase at their melting temperature and temperature coefficients of thermal conductivity for LA, MA, PA, and SA have been found to be 0.37, 0.39, 0.23, and 0.35 W K^?1 m^?1 and 0.00935, 0.00446, 0.01095, and 0.00295 K^?1, respectively. The ratios of thermal conductivity of liquid phase to thermal conductivity of solid phase for LA, MA, PA, and SA have also been measured to be 0.52, 0.48, 0.25, and 0.59, respectively, with a Bridgman-type directional solidification apparatus.     

Thermal conductivity enhancement of copper–diamond composites by sintering with chromium additive

The thermal diffusivity (TD) and thermal conductivity (TC) of Cu–Cr–diamond composite materials were examined in the temperature range from 50 to 300 °C for diamond volume fractions of 22, 40, 50, 55, and 60 %. The samples were fabricated by the plasma pulse sintering (PPS) method. TC does not increase proportionally with the diamond fraction in the particular composite materials. The highest TD was determined for 50 % diamond volume fraction, and the evaluated TC reached 658 W m^?1 K^?1 at 50 °C. This article complements earlier articles concerning synthesis and characterization of the diamond–copper composites produced by the PPS method.     

Preparation and characterization of the bacterial cellulose/polyurethane nanocomposites

New nanocomposites based on bacterial cellulose nanofibers (BCN) and polyurethane (PU) prepolymer were prepared and characterized by SEM, FT-IR, XRD, and TG/DTG analyses. An improvement of the interface reaction between the BCN and the PU prepolymer was obtained by a solvent exchange process. FT-IR results showed the main urethane band at 2,270 cm^?1 to PU prepolymer; however, in nanocomposites new bands appear as disubstituted urea at 1,650 and 1,550 cm^?1. In addition, the observed decrease in the intensity of the hydroxyl band (3,500 cm^?1) suggests an interaction between BCN hydroxyls and NCO-free groups. The nanocomposites presented a non-crystalline character, significant thermal stability (up to 230 °C) and low water absorption when compared to pristine BCN.     

Influence of Ca2+ substitution on thermal,structural, and conductivity behavior of Bi1−xCaxFeO3−y (0.40 ≤ x ≤ 0.55)

Bi_1?xCa_xFeO_3?y (0.40 ≤ x ≤ 0.55) perovskite oxides have been synthesized by solid-state reaction method to study their properties as a cathode material for intermediate temperature solid oxide fuel cells. The as prepared samples were characterized by X-ray diffraction, differential thermal analyzer/thermogravimetry, dilatometer, and impedance spectroscopy to study their structural, thermal, and electrical properties. The Rietveld refinement results confirmed that all the samples exhibit tetragonal structure with P4mm space group. In addition to this, sample x = 0.55 exhibits Ca₂Fe₂O₅ as a secondary phase. It has been observed that lattice parameters decrease with increase in calcium content. The thermal expansion coefficient and ionic conductivity increases with increase in calcium content up to x = 0.50. The highest ionic conductivity is observed for Bi_0.5Ca_0.5FeO_3?y i.e. 1.71 × 10^?2 S cm^?1.