Evolution of Morphology and Structure During Crystallization and Melting in Syndiotactic Polypropylene

Polypropylene( PP) has developed into one of the most useful plastic materials.Ithas many attractive properties,among them,a relatively low price.It also possesses awide range of possibilities for chemical modification[1 ,2 ] .The structure and morphologyof PP have a directimpacton the final properties. Therefore,there is growing interestinunderstanding the structure and morphology of stereoregular PP[1～ 6] .　For isotactic PP(i PP) ,extensive structural and morphological studies have be…     

热历史对尼龙1212熔融行为的影响

利用DSC方法研究了不同热历史条件对尼龙1212熔融行为的影响.不同的热历史条件下,在DSC曲线上,观察到尼龙1212产生2个或3个熔融峰,依据聚合物结晶理论,对各峰的来源进行了分析.在160℃下不同温度退火120 min的尼龙1212样品DSC曲线上,低温结晶熔融峰主要由低温结晶形成的一些微晶体或者片晶熔融产生,其晶体完善程度较差,熔融峰值较低,峰面积较小;主熔融峰是由样品在淬火过程中形成的晶体和升温过程中低温结晶形成的晶体的熔融重结晶形成较为完善的晶体熔融所产生,熔融峰值较高,峰面积较大.在不同的升温速率条件下,熔融峰温度有所移动,表明不同升温速率条件下产生的熔融峰的结晶晶型是相同的.在不同结晶时间下结晶,延长结晶时间对较高完善程度晶体的生长有利.在不同温度下依次退火处理的样品,熔融产生两个附加峰,这两个附加峰的峰温都比它们相应的退火温度高,而峰高和峰面积随退火温度降低而减小.根据等温结晶结果,由Hoffman方法确定了尼龙1212的平衡熔融温度为202.8℃.     

Thermal memory of poly(3‐hydroxybutyrate) using temperature‐modulated differential scanning calorimetry

The influence of thermal history on morphology, melting, and crystallization behavior of bacterial poly(3‐hydroxybutyrate) (PHB) has been investigated using temperature‐modulated DSC (TMDSC), wide‐angle X‐ray diffraction (WAXRD) and polarized optical microscopy (POM). Various thermal histories were imparted by crystallization with continuous and different modulated cooling programs that involved isoscan and cool–heat segments. The subsequent melting behavior revealed that PHB experienced secondary crystallization during heating and the extent of secondary crystallization varied with the cooling treatment. PHB crystallized under slow, continuous, and moderate cooling rates were found to exhibit double melting behavior due to melting of TMDSC scan‐induced secondary crystals. PHB underwent considerable secondary crystallization/annealing that took place under modulated cooling conditions. The overall melting behavior was interpreted in terms of recrystallization and/or annealing of crystals. Interestingly, the PHB analyzed by temperature modulation programs showed a broad exotherm before the melting peak in the nonreversing heat capacity curve and a multiple melting reversing curve, verifying that the melting–recrystallization and remelting process was operative. WAXRD and POM studies supported the correlations from DSC and TMDSC results. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 70–78, 2006     

Crystallization and thermal properties of PLLA comb polymer

Poly(L ‐lactide) (PLLA) on poly(2‐hydroxyethyl methacrylate) (PHEMA) backbone was prepared by a combination of atom transfer radical polymerization (ATRP) and ring‐opening polymerization (ROP). The structure of the comb polymer was analyzed by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering (SAXS), and differential scanning calorimetry (DSC). WAXD result indicates that the comb polymer has α crystalline modification with a 10₃ helical conformation. Lamellar parameters of the crystalline structure were obtained by one‐dimension correlation function (1DCF) calculated from SAXS results. The calculations show that the thickness of crystalline layer is controlled by annealing temperature and comb structure. DSC was applied to study kinetics of the crystallization and melting behavior. Two melting peaks on melting curves of the comb polymer at different crystallization temperature were detected, and the peak at higher temperature is attributed to the melt‐recrystallization. The equilibrium melting temperature is found to be influenced by the comb structure. In this article the effects of the comb structure on Avrami exponent, equilibrium melting point and melting peak of the comb polymer were discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 589–598, 2008     

Morphology development during solid-state annealing of poly(ether-ester) multiblock copolymers

Morphology development during isothermal annealing of poly(ether-ester) multiblock copolymers with hard segments containing poly(tetramethylene isophthalate) is examined by differential scanning calorimetry (DSC) and small-angle x-ray scattering (SAXS). Reorganization in the solid-state occurs by melting and recrystallization. At temperatures close to the melting point, glass transition measurements after quenching from the annealing temperature suggest microphase mixing follows melting. The temperature of maximum recrystallization rate is elevated relative to that of isothermal crystallization. SAXS experiments suggest that a memory of the initial morphology is retained during annealing. Aspects of the DSC scans related to crystallization on cooling and rescanning also suggest that the morphology at the annealing temperature plays a governing role in the determination of the degree of order possible on cooling. The crystalline regions stable at the annealing temperature are envisioned to function in a dual role, acting as nucleation centers for recrystallization and as a form of “constraint” to ordering on cooling. © 1996 John Wiley & Sons, Inc.     

Analysis of the complex thermal behavior of poly(L‐lactic acid) film. I. Samples crystallized from the glassy state

The melting behavior of poly(L ‐lactic acid) film crystallized from the glassy state, either isothermally or nonisothermally, was studied by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering (SAXS), differential scanning calorimetry (DSC), and temperature‐modulated differential scanning calorimetry (TMDSC). Up to three crystallization and two melting peaks were observed. It was concluded that these effects could largely be accounted for on the basis of a “melt‐recrystallization” mechanism. When molecular weight is low, two melting endotherms are readily observed. But, without TMDSC, the double melting phenomena of high molecular weight PLLA is often masked by an exotherm just prior to the final melting, as metastable crystals undergo melt‐recrystallization during heating in the DSC. The appearance of a double cold‐crystallization peak during the DSC heating scan of amorphous PLLA film is the net effect of cold crystallization and melt‐recrystallization of metastable crystals formed during the initial cold crystallization. Samples cold‐crystallized at 80 and 90 °C did not exhibit a long period, although substantial crystallinity developed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3200–3214, 2006     

聚己内酯在聚己内酯/苯乙烯丙烯腈共聚物共混体系中的受限结晶

通过示差扫描量热 (DSC)、广角X 射线衍射 (WAXD)和小角X 射线散射 (SAXS)在不同尺度范围研究了聚己内酯 (PCL) 苯乙烯 丙烯腈共聚物 (SAN)共混体系中PCL的结晶行为 .由于该体系中SAN的玻璃化温度高于PCL的熔点 ,从而导致了PCL的结晶行为是一种受限结晶 .研究结果表明PCL的结晶行为从宏观 (DSC结果 )、介观 (SAXS结果 )到微观 (WAXD结果 )都受到了高玻璃化温度SAN的限制 .     

Morphology and melting behavior of semicrystalline poly(ethylene terephthalate). II. Annealed PET

Annealing of poly(ethylene terephthalate) samples crystallized under isothermal conditions above the crystallization temperature has a marked influence on their morphology and results in increased thermal stability of the crystalline structure as indicated by the melting point increase of the samples. The morphological transformation processes induced by annealing are very complex and depend on the thermal history of the samples, i.e., crystallization temperature and heating procedure. Depending on the nature of the processes occurring during annealing, various parameters characterizing the semicrystalline state of the samples can be affected such as the degree of crystallinity, the long spacing, the thickness of amorphous and crystalline layers, the crystal perfection, the fold-surface structure, and the mosaic structure of the crystalline lamellae. Annealing involves a solid-state transformation of the original crystalline structure including crystal perfection without thickening or a melting followed by recrystallization with crystal perfection and crystal thickening. The combination of differential scanning calorimetric (DSC) measurements and small-angle x-ray scattering is a powerful analytical tool to detect morphological changes and helps in deciding on the processes which are involved in the transformation of the microstructure upon annealing.     

Influence of additives on the crystal structure and melting behavior of poly(ethylene‐2,6‐naphthalene dicarboxylate)

The influence of additives on the crystal modification and melting behavior of poly(ethylene‐2,6‐naphthalene dicarboxylate) (PEN) was investigated with wide‐angle X‐ray diffraction and differential scanning calorimetry (DSC). The addition of a nucleating promoter, Ceraflour 993, had no effect on the crystal modification and melting behavior of PEN crystallized under all chosen experimental conditions. However, the addition of a nucleating agent, sodium benzoate (SB), did affect the crystal modification and melting behavior of PEN when PEN/SB was crystallized at a higher temperature, but not at a lower temperature. A mixture of α and β modifications of PEN was obtained, and an overlapped dual melting peak was observed in DSC curves when PEN was crystallized at a higher temperature in the presence of SB, instead of a single crystal form and a single melting peak for the crystallization of pure PEN. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 296–301, 2004     

Crystal modifications and multiple melting behavior of poly(L‐lactic acid‐co‐D‐lactic acid)

The crystal modifications and multiple melting behavior of poly(L ‐lactic acid‐co‐D ‐lactic acid) (98/2) as a function of crystallization temperature were studied by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). It was found that the disorder (α′) and order (α) phases of poly(L ‐lactic acid) (PLLA) were formed in cold‐crystallized poly(L ‐lactic acid‐co‐D ‐lactic acid) samples at low (<110 °C) and high (≥110 °C) temperatures, respectively. A disorder‐to‐order (α′‐to‐α) phase transition occurred during the annealing process of the α′‐crystal at elevated temperatures, which proceeded quite slowly even at the peak temperature of the exotherm P_exo but much more rapidly at higher temperature close to the melting region. The presence or absence of an additional endothermic peak before the exotherm in the DSC thermograph of the α′‐crystal was strongly dependent on the heating rate, indicating that a melting process involved during the α′‐to‐α phase transition. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Fractional crystallization behavior of PCL and PEG in blends

The crystallization behavior of poly(e-caprolactone)/poly(ethylene glycol) (PCL/PEG) blend was investigated by differential scanning calorimetry (DSC) and polarized microscopy (POM). Individual phase transition peaks in the DSC curves for both PEG and PCL in all the polymer blends with different PCL contents were observed. The crystallization and melting peak temperatures of PEG were at 41 and 65°C, respectively; while the crystallization and melting temperatures of PCL located at 28 and 56°C, respectively. In-situ POM results demonstrated that spherulites crystalline morphology was formed for both PCL and PEG homopolymers. In PEG/PCL blend, however, both the phase separation morphology and spherulitic morphology can be observed. In blends with 30 or 50 wt % PCL, the PCL component formed dispersed phase and crystallized at lower temperature. However, in blends with 70% PCL, the phase inversion behavior occurred. The continuous PCL phase crystallized at 35°C, while the PEG dispersed phase crystallized at a lower temperature. Fractional crystallization behavior of PEG and PCL was controlled by temperature. The spherulites growth rate of PEG was greatly influenced by temperature, instead of the content of PCL component in the PCL/PEG blends.     

CRYSTALLIZATION BEHAVIOR OF A THERMOTROPIC LIQUID CRYSTAL COPOLYESTER

A thermotropic liquid crystal copolyester resin based on p-hydroxybenzoic acid, 2, 6-naphthoic acid, hydroxyquinone and PET was synthesized by melt condensation and studied. The results based on DSC and X-ray diffraction indicated that there were a rapid and a slow crystallization processes for the copolyester at certain conditions. A critical temperature was suggested, below which the slow crystallization could hardly happen. Above the critical temperature the extent of the slow crystallization process depended not only on annealing temperature but also on the annealing time. A fine crystal structure with high melting point and narrow diffraction peak was formed under favorable conditions.     

Crystalline Morphology and Crystallization Kinetics of Melt-miscible Crystalline/Crystalline Polymer Blends of Poly（vinylidene fluoride） and Poly（butylene succinate-co-24mol% hexamethylene succinate）

Poly（vinylidene fluoride） （PVDF） and poly（butylene succinate-co-24 mol% hexamethylene succinate） （PBHS）, both crystalline polymers, formed melt-miscible crystalline/crystalline polymer blends. Both the characteristic diffraction peaks and nonisothermal melt crystallization peak of each component were found in the blends, indicating that PVDF and PBHS crystallized separately. The crystalline morphology and crystallization kinetics of each component were studied under different crystallization conditions for the PVDF/PBHS blends. Both the spherulitic growth rates and overall isothermal melt crystallization rates of blended PVDF decreased with increasing the PBHS composition and were lower than those of neat PVDF, when the crystallization temperature was above the melting point of PBHS component. The crystallization mechanism of neat and blended PVDF remained unchanged, despite changes of blend composition and crystallization temperature. The crystallization kinetics and crystalline morphology of neat and blended PBHS were further studied, when the crystallization temperature was below the melting point of PBHS component. Relative to neat PBHS, the overall crystallization rates of the blended PBHS first increased and then decreased with increasing the PVDF content in the blends, indicating that the preexisting PVDF crystals may show different effects on the nucleation and crystal growth of PBHS component in the crystalline/crystalline polymer blends.     

热处理对聚乙烯／炭黑导电复合体系形态结构及PTC特性的影响

借助ＷＡＸＤ、ＳＡＸＤ和ＤＳＣ等手段研究了炭黑与聚乙烯复合体系在不同热处理条件下的结晶行为及聚集态结构的大尺寸效应对ＰＴＣ特性的影响。由此提出，不仅结晶度大小，而且聚集大尺寸效应性能对ＰＴＣ行性有重要影响的新观点。     

The double melting behavior of a liquid crystalline polyimide derived from PMDA and 1,3‐bis[4‐(4′‐aminophenoxyl) cumyl] benzene

The double melting behavior of a thermotropic liquid crystalline polyimide was studied by means of differential scanning calorimetry (DSC), polarized light microscopy (PLM), transmission electron microscopy (TEM), wide‐angle X‐ray diffraction (WAXD), and small‐angle X‐ray scattering (SAXS). This liquid crystalline polyimide exhibited a normal melting peak around 278 °C and transformed into a smectic A phase. The smectic A phase changed to nematic phase upon heating to 298 °C, then became isotropic melt around 345 °C. The samples annealed or isothermally crystallized at lower temperature showed double melting endotherms during heating scan. The annealing‐induced melting endotherm was highly dependent on annealing conditions, whereas the normal melting endotherm was almost not influenced by annealing when the annealing temperature was low. Various possibilities for the lower melting endotherm are discussed. The equilibrium melting points of both melting peaks were extrapolated to be 283.2 °C. Combined analytical results showed that the double melting peaks were from the melting of the two types of crystallites generated from two crystallization processes: a slow and a fast one. Fast crystallization may start from the well‐aligned liquid crystal domains, whereas the slow one may be from the fringed or amorphous regions. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3018–3031, 2000     

Study on Melting and Recrystallization of Poly(butylene succinate) Lamellar Crystals via Step Heating Differential Scanning Calorimetry

Differential scanning calorimetry (DSC) has been widely applied to study crystallization and melting of materials.However,for polymeric lamellar crystals,the melting thermogram during heating process usually exhibits a broad endothermic peak or even multiple endotherms,which may result from changes of metastability via recrystallization process.Sometimes,the recrystallization exotherm cannot be observed due to its overlapping with the melting endotherm.In this work,we employed a step heating procedure consisting of successive heating and temperature holding stages to measure the metastability of isothermally crystallized poly(butylene succinate) (PBS) crystals.With this approach we could gain the fraction of crystals melted at different temperature ranges and quantitatively detect the melting-recrystallization behavior.The melting-recrystallization behavior depends on the polymer chain structure and the crystallization temperature.For instance,PBS block copolymer hardly shows recrystallization behavior while PBS oligomer and high molecular weight PBS homopolymer demonstrate remarkable melting-recrystallization phenomenon.High molecular weight PBS isothermally crystallized in the low temperature range shows multiple melting-recrystallization while those isothermally crystallized at elevated temperatures do not exhibit observable recrystallization behavior.Furthermore,the melting endotherms were fitted via the melting kinetics equations.The original isothermally crystallized lamellae demonstrate quite different melting kinetics from the recrystallized lamellar crystals that melt at the highest temperature range,which is attributed to the different degrees of stabilization.Finally,the mechanism of melting-recrystallization is briefly discussed.We propose that apparent meltrecrystallization phenomenon be observed when melting of preformed lamellar crystals and recrystallization of thicker lamellae have similar free energy barrier.     

Morphology and melting behavior of nascent ultra-high molecular weight polyethylene

The nascent morphology of UHMW PE exhibits high melting point, high crystallinity, and increased WAXS line breadth relative to samples formed by melt crystallization. Different empirical relationships between crystal size and melting point are observed for nascent and molded samples. This differentiation is removed following nitric acid treatment of the nascent flake. Solid-state annealing behavior is differentiated by several regimes. Regime I is characterized by increasing crystallite dimensions and crystallinity at low annealing temperatures. Regime II[a] and II[b] is identified by double melting in DSC scans of moldings and nascent flake, respectively. The double melting is due to partial melting with incomplete recrystallization. Regime II[a] of moldings is differentiated from Regime II[b] of flake by an increase in melting point of the higher melting endotherm. Within Regime II[b], the partial melting of the nascent structure is sensitive to the distribution of morphological stability. Regime III is initiated at annealing temperatures approaching the zero heating rate melting point, and shows melting kinetics by DSC or time-resolved WAXS using synchrotron x-ray radiation. The superheat, partially associated with Regime III behavior, is sensitive to morphological heterogeneity and annealing history. Morphological models are discussed which highlight the role of noncrystalline regions and melting kinetics on the melting behavior of nascent form crystallinity. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 495–517, 1998     

The multiple melting endotherms from poly(butylene terephthalate)

The melting behavior of poly(butylene terephthalate) (PBT) has been investigated, and a simulation has been performed to determine whether the multiple melting endotherms observed during the thermal analysis of PBT can be explained by the simultaneous melting and recrystallization of an initial distribution of crystal melting temperatures that contains only one maximum and two inflection points. Specimens that were cooled at constant rates from the melt showed between one and three melting endotherms upon heating in a differential scanning calorimeter (DSC). The position and breadth of the crystallization exotherms upon cooling from the melt and small-angle x-ray scattering showed that as the cooling rate is increased, the distribution of melting temperatures broadens and shifts to lower temperatures. By combining temperature-dependent recrystallization with an initial distribution of melting temperatures, simulated DSC curves were produced that agreed well with experimental DSC curves. In instances of triple peaked curves, the high temperature peak was due to crystals formed during the scanning process, and the middle and low temperature peaks were due to crystals originally present in the material. Satisfactory agreement between the experimental and simulated curves was found without considering additional crystallization from the amorphous regions during the scanning process.     

Crystal structure and thermal behavior of cold-crystallized poly(trimethylene terephthalate)

The structure and thermal behavior of cold-crystallized poly(trimethylene terephthalate) (PTT) are revealed in detail by DSC, AFM, TEM, and WAXD as well as in situ FTIR and SAXS techniques. There is no effect of crystallization temperature and initial state on the crystal modification, yet the morphology is strongly affected by these two factors. First, the small rod-like lamellae for PTT are obtained during the cold crystallization instead of the spherulites formed in the melt crystallization. Second, the edge-on lamellar orientation in thin films is identified during the cold crystallization. The thickness and the lateral width of rod-like lamellae get larger and larger with increasing crystallization temperature. Thin lamellar crystals assemble randomly when the cold-crystallization temperature is lower, while lamellar stacks composed of thicker lamellae are observed when the PTT was annealed at elevated temperature. Moreover, for the cold-crystallized PTT, the final melting temperature does not vary with the crystallization temperature. This phenomenon is explained by the structural improvement during the heating process. For the cold-crystallized PTT sample at lower temperature, three transitions occur when it is heated again: the relaxation of the rigid amorphous phase, the reorganization of molecules in the intermediate phase, and then the melt–recrystallization behavior. Those transitions finally lead to thicker lamellae besides a higher crystallinity before the final fusion. Therefore, the final melting peak of these lamellae is at the same temperature.