Synthesis and characterization of Co<Subscript>0.8</Subscript>Zn<Subscript>0.2</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles

Cobalt zinc ferrite, Co_0.8Zn_0.2Fe₂O₄, nanoparticles have been synthesized via autocatalytic decomposition of the precursor, cobalt zinc ferrous fumarato hydrazinate. The X-ray powder diffraction of the ‘as prepared’ oxide confirms the formation of single phase nanocrystalline cobalt zinc ferrite nanoparticles. The thermal decomposition of the precursor has been studied by isothermal, thermogravimetric and differential thermal analysis. The precursor has also been characterized by FTIR, and chemical analysis and its chemical composition has been determined as Co_0.8Zn_0.2Fe₂(C₄H₂O₄)₃·6N₂H_4. The Curie temperature of the ‘as-prepared oxide’ was determined by AC susceptibility measurements.     

Preparation and characterization of superconducting YBa<Subscript>2</Subscript>(Cu<Subscript>1−x</Subscript>Cr<Subscript>x</Subscript>)<Subscript>4</Subscript>O<Subscript>8</Subscript> oxides by thermal analysis

In this study the formation of chromium substituted YBa₂Cu₄O₈ (Y-124) superconductors has been investigated by TG/DTA measurements. The YBa₂(Cu_1−xCr_x)₄O₈ ceramics with nominal compositions of x=0.01, 0.03, 0.05, 0.10 and 0.20 have been prepared by an aqueous sol-gel method using aqueous mixtures of the corresponding metal acetates and nitrates. Homogeneous precursor gels were obtained by complexing metal ions with tartaric acid. To assist the interpretation of the results obtained the synthesis products were additionally characterized by X-ray powder diffraction (XRD) and resistivity measurements. It was determined that doping the YBa₂Cu₄O₈ phase with chromium has a strong effect on the phase purity and superconducting properties of the synthesis products.     

The Microstructure of Cobalt Silica Gel Catalyst in the Presence of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Additive

The physico-chemical characteristics and microstructure of cobalt silica gel catalysts with an Al₂O₃ additive (up to 10%) for the synthesis of hydrocarbons by the Fischer–Tropsch method are studied using a set of methods including X-ray diffraction, BET, IR spectroscopy, and temperature-programmed reduction of H₂, as well as scanning and transmission electron microscopy. Phases with a spinel structure, Со₃О₄, CoAl₂O₄, and solid solutions on their basis are identified in the samples. The addition of Al₂O₃ changes the degree of heterogeneity and the orientation of the cobalt crystallites in the oxide and reduced forms of the catalysts. Addition of 1% Al₂O₃ stabilizes Со₃О₄ in the spinel form with a structure close to the normal one and promotes the formation of cobalt with a unimodal distribution of particles with an average size of 8 nm. The catalyst is characterized by maximum activity and selectivity with respect to C⁵⁺ carbons.     

Carbon paste electrode modified with Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles and BMI.PF<Subscript>6</Subscript> ionic liquid for determination of estrone by square-wave voltammetry

A carbon paste electrode (CPE) modified with Fe₃O₄ nanoparticles (Fe₃O₄ NP) and the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate (IL BMI.PF₆) was employed for the electroanalytical determination of estrone (E1) by square-wave voltammetry (SWV). At the modified electrode, cyclic voltammograms of E1 in B–R buffer (pH 12.0) showed an adsorption-controlled irreversible oxidation peak at around +0.365 V. The anodic current increased by a factor of five times and the peak potential shifted 65 mV to less positive values compared with the unmodified CPE. Under optimized conditions, the calibration curve obtained showed two linear ranges: from 4.0 to 9.0 μmol L^?1 and from 9.0 to 100.0 μmol L^?1. The limits of detection (LOD) and quantification (LOQ) attained were 0.47 and 4.0 μmol L^?1, respectively. The proposed modified electrode was applied to the determination of E1 in pork meat samples. Data provided by the proposed modified electrode were compared with data obtained by UV–vis spectroscopy. The outstanding performance of the electrochemical device indicates that Fe₃O₄ NP and the IL BMI.PF₆ are promising materials for the preparation of chemically modified electrodes for the determination of E1.     

Comparative study of the synthesis of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> and NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> in silica through the polymerized complex route of the sol–gel method

In this work the synthesis of CoFe₂O₄-SiO₂ and NiFe₂O₄-SiO₂ nanocomposites was studied via the sol–gel method, using the polymerized complex route. The polymerized precursors obtained by the reaction of citric acid, ethylene glycol, tetraethylorthosilicate, ferric nitrate, and cobalt nitrate or nickel chloride were characterized by nuclear magnetic resonance (NMR) and infrared (IR) spectroscopy. NMR and IR spectra of the precursors, without and with metallic ions, show the formation of polymeric chains with ester and ether groups and complexes of metal-polymeric precursor. The nanocomposites were obtained by the thermal decomposition of the organic fraction and characterized by X-ray diffraction (XRD) and vibrating sample magnetometry (VSM). XRD patterns show the formation of CoFe₂O₄ and NiFe₂O₄ in an amorphous silica matrix above 400 °C in both cases. When the calcination temperature was 800 °C the particle size of the crystalline phases, calculated using the Scherrer equation, reached ∼35 nm for the two oxides. VSM plots show the ferrimagnetic behavior that is expected for this type of magnetic material; the magnetization at 12.5 KOe of the CoFe₂O₄-SiO₂ and NiFe₂O₄-SiO₂ compounds was 29.5 and 17.4 emu/g, respectively, for samples treated at 800 °C.     

Characterization of nanosized ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript> spinel synthesized by the sol–gel method

Single-phase zinc aluminate (ZnAl₂O₄) nanoparticles with the spinel structure was successfully obtained by the sol–gel method. The nanoparticles are crystalline with no impurities related to ZnO or Al₂O₃ residues. The microstructural environment of aluminum ions changes with heat treatment temperature, as observed by FT-IR and also by ²⁷Al solid-state magic angle spinning nuclear magnetic resonance (MAS NMR) spectra. The photoluminescence spectra show that the emission of pristine ZnAl₂O₄ may change depending on the calcining temperature due to the quantum size effect.     

Effect of cerium dioxide on the properties of monolithic CuO-ZnO-CeO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/cordierite catalysts in methanol decomposition

Cerium dioxide as a component of CuO-ZnO-CeO₂/Al₂O₃/cordierite catalysts stabilizes their action in the decomposition of methanol by preventing carbon deposition on the surface and facilitating hydrogen formation with selectivity and yield in the range 85–96%. The optimal indices for this reaction are obtained for a CeO₂-CuO/Al₂O₃/cordierite sample prepared using an ammonium precursor for cerium, (NH₄)₂Ce(NO₃)₆. This catalyst displays enhanced reductive capacity relative to the analogous CeO₂-CuO composition prepared using Ce(NO₃)₃·6H₂O.     

Tin trifluoroacetylacetonate [Sn(C<Subscript>5</Subscript>H<Subscript>4</Subscript>O<Subscript>2</Subscript>F<Subscript>3</Subscript>)<Subscript>2</Subscript>] as a precursor of tin dioxide in APCVD process

A new method of synthesis of volatile complex, tin trifluoroacetylacetonate [Sn(C₅H₄O₂F₃)₂], was proposed. The prepared compound was identified by IR spectroscopy, CH analysis, X-ray powder diffraction, and DTA/TGA, the composition was confirmed by MALDI-TOF mass spectrometry, crystal structure was established. Thin films of tin dioxide on silicon were obtained by atmospheric pressure chemical vapor deposition using [Sn(C₅H₄O₂F₃)₂] as a precursor. The morphology and composition of the films were studied by scanning electron microscopy, EDX elemental analysis, and X-ray powder diffraction. Surface resistance and light transmission in visible and near IR region were studied.     

Amperometric hydrogen peroxide sensor based on the use of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> hollow nanostructures

The authors report on the preparation of a hollow-structured cobalt ferrite (CoFe₂O₄) nanocomposite for use in a non-enzymatic sensor for hydrogen peroxide (H₂O₂). Silica (SiO₂) nanoparticles were exploited as template for the deposition of Fe₃O₄/CoFe₂O₄ nanosheets, which was followed by the removal of SiO₂ template under mild conditions. This leads to the formation of hollow-structured Fe₃O₄/CoFe₂O₄ interconnected nanosheets with cubic spinel structure of high crystallinity. The material was placed on a glassy carbon electrode where it acts as a viable sensor for non-enzymatic determination of H₂O₂. Operated at a potential of ?0.45 V vs. Ag/AgCl in 0.1 M NaOH solution, the modified GCE has a sensitivity of 17 nA μM^?1 cm^?2, a linear response in the range of 10 to 1200 μM H₂O₂ concentration range, and a 2.5 μM detection limit. The sensor is reproducible and stable and was applied to the analysis of spiked urine samples, where it provided excellent recoveries.

Open image in new window

Graphical abstract Schematic of a cobalt ferrite (CoFe₂O₄) hollow structure for use in electrochemical determination of H₂O₂. The sensor shows a low detection limit, a wide linear range, and excellent selectivity for H₂O₂.

     

Kinetics of phase formation upon the treatment of La<Subscript>2</Subscript>(SO<Subscript>4</Subscript>)<Subscript>3</Subscript> and La<Subscript>2</Subscript>O<Subscript>2</Subscript>SO<Subscript>4</Subscript> in a hydrogen flow

The sequence of phases occurring during treatment of lanthanum sulfate, La₂(SO₄)₃ and lanthanum oxysulfate, La₂O₂SO₄ in a hydrogen flow is established. The temperature ranges in which homogeneous La₂O₂S is produced are revealed: when La₂(SO₄)₃ is a precursor, the range is 770–1220 K; in the case of La₂O₂SO₄, the interval is 950–1220 K. The kinetic curves showing the time dependence of the yield of La₂O₂S is constructed and treated using the Avrami-Erofeev and contracting volume equations. The activation energies of the reactions are determined.     

Electrochemical performance of novel Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> glass-ceramic nanocomposites as electrodes for energy storage devices

The novel Li₃V₂(PO₄)₃ glass-ceramic nanocomposites were synthesized and investigated as electrodes for energy storage devices. They were fabricated by heat treatment (HT) of 37.5Li₂O–25V₂O₅–37.5P₂O₅?mol% glass at 450 °C for different times in the air. XRD, SEM, and electrochemical methods were used to study the effect of HT time on the nanostructure and electrochemical performance for Li₃V₂(PO₄)₃ glass-ceramic nanocomposites electrodes. XRD patterns showed forming Li₃V₂(PO₄)₃ NASICON type with monoclinic structure. The crystalline sizes were found to be in the range of 32–56 nm. SEM morphologies exhibited non-uniform grains and changed with variation of HT time. The electrochemical performance of Li₃V₂(PO₄)₃ glass-ceramic nanocomposites was investigated by using galvanostatic charge/discharge methods, cyclic voltammetry, and electrochemical impedance spectroscopy in 1 M H₂SO₄ aqueous electrolyte. The glass-ceramic nanocomposites annealed for 4 h, which had a lower crystalline size, exhibited the best electrochemical performance with a specific capacity of 116.4 F g^?1 at 0.5 A g^?1. Small crystalline size supported the lithium ion mobility in the electrode by decreasing the ion diffusion pathway. Therefore, the Li₃V₂(PO₄)₃ glass-ceramic nanocomposites can be promising candidates for large-scale industrial applications in high-performance energy storage devices.     

Preparation and electrochemical performance of nano-structured Li<Subscript>2</Subscript>Mn<Subscript>4</Subscript>O<Subscript>9</Subscript> for supercapacitor

Nano-structured spinel Li₂Mn₄O₉ powder was prepared via a combustion method with hydrated lithium acetate (LiAc·2H₂O), manganese acetate (MnAc₂·4H₂O), and oxalic acid (C₂H₂O₄·2H₂O) as raw materials, followed by calcination of the precursor at 300 °C. The sample was characterized by X-ray diffraction, scanning electron microscope, and energy-dispersive X-ray spectroscopy techniques. Electrochemical performance of the nano-Li₂Mn₄O₉ material was studied using cyclic voltammetry, ac impedance, and galvanostatic charge/discharge methods in 2 mol L⁻¹ LiNO₃ aqueous electrolyte. The results indicated that the nano-Li₂Mn₄O₉ material exhibited excellent electrochemical performance in terms of specific capacity, cycle life, and charge/discharge stability, as evidenced by the charge/discharge results. For example, specific capacitance of the single Li₂Mn₄O₉ electrode reached 407 F g⁻¹ at the scan rates of 5 mV s⁻¹. The capacitor, which is composed of activated carbon negative electrode and Li₂Mn₄O₉ positive electrode, also exhibits an excellent cycling performance in potential range of 0–1.6 V and keeps over 98% of the maximum capacitance even after 4,000 cycles.     

Hydrogen generation from H<Subscript>2</Subscript>O/H<Subscript>2</Subscript>O<Subscript>2</Subscript>/MnWO<Subscript>4</Subscript> system

Hydrogen gas as a clear energy resource was found to be largely bubbled from a H₂O/H₂O₂/MnWO₄ system. MnWO₄ powder was fabricated by an aqueous reaction method. The powder was characterized with X-ray diffraction (XRD), transmission electron microscope (TEM), and X-ray photoelectron spectrometry (XPS). The efficiency of the hydrogen generation increases with an increase in initial pH in the appropriate range, H₂O₂ proportion, MnWO₄ proportion, and intensity of light resource. Calcining at 400 °C for 1 h can make the MnWO₄ powder synthesized by an aqueous reaction more effective for H₂ generation and more stable in higher initial pH. The MnWO₄ catalyst shows a long-term stability for photocatalytic H₂ generation. A mechanism was suggested for the hydrogen generation from the H₂O/H₂O₂/MnWO₄ system together with XPS analysis.     

Synthesis,structure and thermal decomposition of [Ni(NH<Subscript>3</Subscript>)<Subscript>6</Subscript>][VO(O<Subscript>2</Subscript>)<Subscript>2</Subscript>(NH<Subscript>3</Subscript>)]<Subscript>2</Subscript>

The compound [Ni(NH₃)₆][VO(O₂)₂(NH₃)]₂ was prepared and characterized by elemental analysis and vibrational spectra. The single crystal X-ray study revealed that the structure consists of [Ni(NH₃)₆]²⁺ and [VO(O₂)₂(NH₃)]⁻ ions. As a result of weak interionic interactions V′···O_p (O_p-peroxo oxygen), ([VO(O₂)₂(NH₃)]⁻)₂ dimers are formed in the solid-state. The thermal decomposition of [Ni(NH₃)₆][VO(O₂)₂(NH₃)]₂ is a multi-step process with overlapped individual steps; no defined intermediates were obtained. The final solid products of thermal decomposition up to 600°C were Ni₂V₂O₇ and V₂O₅.     

Preparation,spectroscopic and thermal analysis of hexa-hydrazine nickel cobalt ferrous succinate precursor and study of solid-state properties of its nanosized thermal product,Ni<Subscript>0.5</Subscript>Co<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>

Nickel cobalt ferrite, Ni_0.5Co_0.5Fe₂O₄, has been prepared by precursor combustion technique from hexa-hydrazine nickel cobalt ferrous succinate precursor. The precursor was characterized by chemical analysis, CHNS analysis, infrared spectroscopy, TG–DTA and mass loss studies. The thermal data show how the precursor decomposes in four steps to give stable ferrite phase. The precursor decomposes autocatalytically once initially ignited, to give the ‘as-prepared’ nano-spinel ferrite. The X-ray diffraction analysis reveals single cubic spinel phase structure. The infrared measurements between 4000 and 350 cm^?1 confirmed the intrinsic cation vibrations of the spinel structure. The SEM image clearly shows the nanosized nature of the ferrite. The dielectric constant and loss tangent are found to decrease with increase in frequency which is due to Maxwell–Wagner interfacial polarization. The loss tangent shows a relaxation peak at ~1 kHz. The variation of DC electrical resistivity with temperature indicates semiconductor behaviour. The temperature- and field-dependent magnetization data of ‘as-prepared’ ferrite reveal that the lattice has either a canted or partially misaligned spin structure due to the nanosized nature of the ferrite.     

Synthesis of nanoparticles of the giant dielectric material,CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> from a precursor route

A complex oxalate precursor, CaCu₃(TiO)₄(C₂O₄)₈·9H₂O, (CCT-OX), was synthesized and the precipitate that obtained was confirmed to be monophasic by the wet chemical analyses, X-ray diffraction, FTIR absorption and TG/DTA analyses. The thermal decomposition of this oxalate precursor led to the formation of phase-pure calcium copper titanate, CaCu₃Ti₄O₁₂, (CCTO) at ≥680°C. The bright-field TEM micrographs revealed that the size of the as synthesized crystallites to be in the 30–80 nm range. The powders so obtained had excellent sinterability resulting in high density ceramics which exhibited giant dielectric constants upto 40000 (1 kHz) at 25°C, accompanied by low dielectric losses, <0.07.     

LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> and LiCoO<Subscript>2</Subscript> composite cathode materials obtained by mechanical activation

New composite cathode materials xLiMn₂O₄/(1 ? x) LiCoO₂(x = 0.7, 0.6, 0.5 и 0.4) were obtained by mechanical activation. According to scanning electron microscopy data, the process was accompanied by pronounced dispersion and fine mixing of the initial components. In the course of the preparation and electrochemical cycling of the composites, LiMn₂O₄ and LiCoO₂ partially reacted, leading to the replacement of manganese with cobalt in the structure of spinel, which was detected by powder X-ray diffraction (XRD), IR and X-ray photoelectron spectroscopy (XPS), and cyclic chronopotentiometry. The specific discharge capacity of composites was ～100 mAh/g.     

Improvement of the cycle life of composite xerogel V<Subscript>2</Subscript>O<Subscript>5</Subscript>/C in aqueous LiNO<Subscript>3</Subscript> solution by addition of vinylene carbonate

The xerogel V₂O₅/C composite was synthesized by a sol-gel method, using the suspension of carbon black in the solution of crystalline V₂O₅ in hydrogen peroxide as the precursor solution. The Li⁺ intercalation/deintercalation reactions of the xerogel V₂O₅/C composite, used as an anode material of a two-electrode cell with an aqueous LiNO₃ solution as the electrolyte, was studied before and after the addition of vinylene carbonate (VC). Upon addition of vinylene carbonate in an amount of only l wt %, the coulombic capacity during galvanostatic cycling, instead of commonly observed permanent fade, displayed an initial increase and then a stable plateau.     

New cobalt and rare earth metal tungstates CoRE<Subscript>2</Subscript>W<Subscript>2</Subscript>O<Subscript>10</Subscript>

A new family of cobalt and rare-earth metal tungstates (CoRE₂W₂O₁₀ where RE=Y, Dy, Ho and Er) were synthesized by heating in the solid-state equimolar CoWO₄/RE₂WO₆ mixtures. The obtained compounds are isostructural and crystallize in the monoclinic system. They melt incongruently in an inert atmosphere at 1494 K (CoY₂W₂O₁₀), 1523 K (CoDy₂W₂O₁₀), 1517 K (CoHo₂W₂O₁₀) and 1493 K (CoEr₂W₂O₁₀). For each CoRE₂W₂O₁₀ compound the solid product of melting is an adequate RE₂WO₆.     

Synthesis and study of sodium triuranate Na<Subscript>2</Subscript>(UO<Subscript>2</Subscript>)<Subscript>3</Subscript>O<Subscript>3</Subscript>(OH)<Subscript>2</Subscript>

Sodium triuranate Na₂(UO₂)₃O₃(OH)₂ was synthesized by the reaction between aqueous uranyl acetate solution and aqueous sodium nitrate solution under hydrothermal conditions at 200°C. The composition and structure of the synthesized compound were determined, and its dehydration and thermal decomposition were studied, by chemical analysis, X-ray diffraction, IR spectroscopy, and thermal analysis.