电感耦合等离子体原子发射光谱（ICP-AES）法测定粉煤灰中的铝

采用碳酸钠-碳酸钾-硼酸分解试样,盐酸浸取,电感耦合等离子体原子发射光谱法测定粉煤灰中的铝含量。铝的测定范围5.00%~25.00%。经加标回收实验,铝元素的加标回收率为99.6%~106%(n=3),方法准确简单,适用于粉煤灰中铝的测定。     

Direct analysis of fly ash materials by inductively coupled plasma atomic emission spectrometry using slurry nebulization

Fly ash samples of cement works were analysed using slurry nebulization inductively coupled plasma atomic emission spectrometric (ICP-AES). Because of the influence of the experimental factors on the signal intensity, the optimal conditions of the analysis circumstances were determined. Control analyses (wet digestion followed by ICP-AES, and XRF of dry powders (pressed pellets)) were also carried out to compare the results. Based on the result, it was concluded that the slurry nebulization method using slurry standard of same type reference material for calibration can be applied for rapid but less precise (RSD 5–10%) determination of the elements in fly ash.     

Single-step microwave digestion with HNO(3) alone for determination of trace elements in coal by ICP spectrometry

A microwave digestion method with HNO₃ alone was conducted at a temperature as high as 250 °C for determination of 19 trace elements (Li, Be, V, Cr, Mn, Co, Ni, Cu, Zn, Ga, As, Se, Rb, Sr, Cd, Cs, Ba, Hg, and Pb) in coal jointly by inductively coupled plasma optical emission spectrometry (ICP-OES), inductively coupled plasma mass spectrometry (ICP-MS), and flow injection ICP-MS (FI-ICP-MS). The validity of determination was assessed by using three standard coals, SRM 1632c, BCR 180, and SARM 19. It was found that the high-temperature digestion led to an extensive decomposition of the organic matrix and clay in coal, and no dissolved and solid carbon remained in the final solution after evaporation. Good recoveries were observed for all trace elements in three coals, with the exception of V, Rb, and Cs in high-ash SARM 19. Additionally, FI-ICP-MS combined with the present digestion without evaporation pretreatment was proved to be a rapid and efficient approach for determination of ultra-trace elements such as Se, Cd, and Hg in coal.     

Characterization and determination of 28 elements in fly ashes collected in a thermal power plant in Argentina using different instrumental techniques

Different techniques were selected for comprehensive characterization of seven samples of fly ashes collected from the electrostatic precipitator of the San Nicolás thermal power plant (Buenos Aires, Argentina). Particle size was measured using laser based particle size analyzer. X-ray diffraction powder (XRD) analysis and scanning electron microscopy (SEM) were used to characterize the mineral phase present in the matrix consisting basically of aluminosilicates and large amounts of amorphous material. The predominant crystalline phases were mullite and quartz. Major and minors elements (Al, Ca, Cl, Fe, K, Mg, Na, S, Si and Ti) were detected by energy dispersive X-ray analysis (EDAX). Trace elements (As, Cd, Co, Cr, Cu, Mn, Ni, Pb, Se, V and Zn) content was quantified by inductively coupled plasma optical emission spectrometry (ICP OES). Different acid mixtures and digestion procedures were compared for subsequent ICP OES measurements of the dissolved samples. The digestion procedures used were: i) a mixture of FH + HNO₃ + HClO₄ (open system digestion); ii) a mixture of FH + HNO₃ (MW-assisted digestion); iii) a mixture of HF and aqua regia (MW-assisted digestion). Instrumental neutron activation analysis (INAA) was employed for the determination of As, Ba, Co, Cr, Ce, Cs, Eu, Fe, Gd, Hf, La, Lu, Rb, Sb, Sc, Sm, Ta, Tb, Th, U and Yb. The validation of the procedure was performed by the analysis of two certified materials namely, i) NIST 1633b, coal fly ash and ii) GBW07105, rock. Mean elements content spanned from 41870 μg g^− 1 for Fe to 1.14 μg g^− 1 for Lu. The study showed that Fe (41870 μg g^− 1) ? V (1137 μg g^− 1) > Ni (269 μg g^− 1) > Mn (169 μg g^− 1) are the main components. An enrichment, with respect to crustal average, in many elements was observed especially for As, V and Sb that deserve particular interest from the environmental and human health point of view.     

Determination of trace elements in coal and coal fly ash by joint-use of ICP-AES and atomic absorption spectrometry

Microwave-acid digestion (MW-AD) followed by inductively coupled plasma-atomic emission spectrometry (ICP-AES), graphite furnace atomic absorption spectrometry (GFAAS), and hydride generation atomic absorption spectrometry (HGAAS) were examined for the determination of various elements in coal and coal fly ash (CFA). Eight certified reference materials (four coal samples and four CFA samples) were tested. The 10 elements (As, Be, Cd, Co, Cr, Mn, Ni, Pb, Sb, and Se), which are described in the Clean Air Act Amendments (CAAA), were especially considered. For coal, the HF-free MW-AD followed by ICP-AES was successful in the determination of various elements except for As, Be, Cd, Sb, and Se. These elements (except for Sb) were well-determined by use of GFAAS (Be and Cd) and HGAAS (As and Se). For CFA, the addition of HF in the digestion acid mixture was needed for the determination of elements, except for As, Sb, and Se, for which the HF-free MW-AD was applicable. The use of GFAAS (Be and Cd) or HGAAS (Sb and Se) resulted in the successful determination of the elements for which ICP-AES did not work well. The protocol for the determination of the 10 elements in coal and CFA by MW-AD followed by the joint-use of ICP-AES, GFAAS, and HGAAS was established.     

Determination of trace elements in fly ash samples by FAAS after applying different digestion procedure

The fly ash samples obtained from Kangal Power Plant were prepared for FAAS analysis by a new approach. The trace elements of the fly ash samples were leached with appropriate solvents under suitable conditions. The leaching method is known as an effective technique for substances dissolving very hard and refractory materials. The leaching effects of solvents and their mixtures were investigated on fly ash samples that are used largely in analysis of soil and sediment samples.The fly ashes mainly consist of glassy aluminosilicates. The major components of the samples are SiO₂, Al₂O₃, CaO and Fe₂O₃. Therefore, decomposition of the silicate lattice of the fly ash is required for liberation of trace elements. The dissolution process can be completed by using a mineral acid such as concentrated HCl. This technique has an advantage that the fly ash can be dissolved without any oxidation at room temperature.Maximum element recoveries were obtained by the procedure of 37% HCl leaching after the samples were treated with 2.0 ml of concentrated HF. It was also observed that maximum mass loss occurred in this procedure. The effect of the four leaching reagents, which are HCl, HNO₃, HClO₄ and HNO₃ + HClO_4, were investigated on fly ash samples that were treated with concentrated HF. An optimum leaching method was determined based on the confidence of analytical results and element recovery rates.     

Application of sequential extraction and the ICP-AES method for study of the partitioning of metals in fly ashes

In this work, the original BCR extraction scheme was modified and applied to study the partitioning of metals in fly ashes. In the first step, the water-soluble fraction was investigated here. The next metal fractions were acid-soluble, reducible, and oxidisable. Two kinds of coal fly ash certified reference materials were analysed. Metal concentrations in the extracts were measured by inductively coupled plasma atomic emission spectrometry (ICP-AES). The efficiency of the extraction process for each step was examined. The partitioning of metals between the individual fractions was investigated and is discussed.     

A pilot study for the production of a certified reference material for trace elements in honey

In the context of the general mandate of the European Union Community Reference Laboratory (CRL) for residues in living animals and their products established at the Istituto Superiore di Sanità, a pilot study was undertaken to assess the possibility of producing a new certified reference material (CRM) for trace elements in a matrix of honey. The elements considered were As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Sn, V and Zn. Their determination was performed by inductively coupled plasma (ICP)-based techniques. Data obtained with different ICP techniques were generally in good agreement. In light of these results, the next step was the effective production of a candidate CRM in a honey matrix. In the preliminary phase, two different types of honey, i.e., Eucalyptus (solid and sticky) and Robinia (viscous and sticky), were pretreated at the Institute for Reference Materials and Measurements, Joint Research Centre, European Commission (EC-JRC-IRMM) in order to produce the materials candidate for the certification process. Approximately 600 ampoules were thus produced for the Robinia honey and 450 ampoules for the Eucalyptus honey, each ampoule containing 5 g of an aqueous solution of honey (with 20% and 30% high purity water, respectively) and sealed under inert gas (Ar). A ring test to determine the levels of the chemical elements and a long-term study to evaluate the stability of the samples is in progress. Tentative figures for the analytes of interest are (in ng g⁻¹): Robinia, As, 1.28±0.09; Cd, 0.59±0.08; Cr, 2.36±0.21; Cu, 57.6±3.2; Fe, 209±9; Mn, 90.8±3; Ni, 18.1±0.6; Pb, 23±1.5; Sn, 8.10±0.35; V, 1.19±0.37; and Zn, 178±4; Eucalyptus, As, 3.18±0.21; Cd, 0.70±0.08; Cr, 2.73±0.22; Cu, 141±6; Fe, 926±16; Mn, 1905±81; Ni, 7.77±0.4; Pb, 138±4; Sn, 7.97±0.16; V, 3.47±0.15; and Zn, 405±9.     

Hair analysis and the early detection of imbalances in trace elements for members of expeditions in Antarctica

In the framework of the Human Biology and Medicine Project of the National Program for Research in Antarctica (Programma Nazionale di Ricerche in Antartide, PNRA) a study was undertaken to explore the suitability of trace element determination in human hair as a tool for the early detection of the impact of extreme environmental conditions on the health of members of the Italian and French expeditions. This study included three campaigns, namely, the 1995–1996 expedition to the Italian base of Terra Nova Bay, as well as the 1997–1998 and 1998–1999 expeditions to both the Italian base of Terra Nova Bay and the Italian–French base of Dome C. Sampling of hair of participants in the expeditions was carried out both prior to departure and at the end of the period spent at the bases. As regards storage, pre-treatment and analysis of hair samples they were performed in accordance with previously established procedures. Acid-assisted microwave digestion was adopted as the best approach for preparing solutions for subsequent analysis by inductively coupled plasma atomic emission spectrometry and inductively coupled plasma mass spectrometry. In the first part of this study, only the elements Ca, Cu, Fe, Mg and Zn were selected, while at a later stage it was decided to also include Co, Cr, Mn, Mo and Ni. Experimental results were subjected to basic statistical analysis to detect possible significant differences in element concentrations that occurred during the sojourn at the bases, with a view to identify possible remedial action to minimize adverse consequences.     

Determination of Ga, Ge, As, Se and Sb in fly ash samples by ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry (USS-ETV-ICP-MS) has been applied to determine Ga, Ge, As, Se and Sb in fly ash samples. The influences of instrument operating conditions and slurry preparation on the ion signals were reported. Pd and ascorbic acid were used as the mixed modifiers to enhance the ion signals. This method has been applied to determine Ga, Ge, As, Se and Sb in NIST SRM 1633a and 1633b coal fly ash reference materials and a fly ash sample collected locally. Since the sensitivities of the elements studied in slurry solution and aqueous solution were different slightly, analyte addition technique was used for the determination of Ga, Ge, As, Se and Sb in these samples. The As and Se analysis results of the reference materials agreed with the certified values. The results for which no certified value was available were also found to be in good agreement between the ETV-ICP-MS results and the reference values. The reference value was obtained by digesting the samples and analyzing the digested sample solutions by pneumatic nebulization Dynamic Reaction Cell™ (DRC) ICP-MS. The method detection limits estimated from analyte addition curves were about 0.23, 0.13, 0.17, 0.25 and 0.11 μg g⁻¹ for Ga, Ge, As, Se and Sb, respectively, in original fly ash samples.     

Inductively coupled plasma optical emission spectrometric determination of trace elements in sediments after sequential selective extraction: effects of reagents and major elements on the analytical signal

The interfering effects due to the reagents and matrix elements associated with a four step sequential extraction procedure on ICPOES determination of trace elements were investigated in a systematic way. The emission lines were selected in order to include the most interesting elements for environmental studies (Zn, Pb, Ni, Cr, V and Cu) and the concentrations ranged according with the values occurring in the real samples. In order to distinguish between chemical and physical interfering effects, the Mg 280.270–Mg 285.213 line intensity ratio was measured, in each condition. Both pneumatic and ultrasonic nebulization were considered for comparison. It was found that both the elements which constitute the sample and the reagents which are added during the sample preparation steps significantly influence the emission intensity of all the analytes, depending on the analytical concentration and the nebulization system. Generally, the signal variations were higher with ultrasonic nebulization. Concerning the interference mechanism, it was found that the effect of the major elements (Na, K, Mg, Ca, Al and Fe) is essentially related to a change of the aerosol generation and transport processes. Differently, acetic acid, ammonium acetate and hydroxylamine hydrochloride significantly improved the plasma excitation conditions, depending on their concentration. A change of the sample introduction efficiency due to the presence of these reagents was also evident. On the contrary, the effect of hydrochloric and nitric acid emerged to be related only to the processes occurring in the sample introduction system.     

ICP-AES 法测定硅铁中痕量元素

采用电感耦合等离子原子发射光谱法测定硅铁中的痕量元素,研究了 Fe 基体对被测元素的影响,并选择了最佳工作条件.被测元素的检测限为 0 .60～76.2 ng/mL,样品加标回收率为 92%～108%,RSD(n=8)<3%.     

Application of ultrasound-assisted acid leaching procedures for major and trace elements determination in edible seaweed by inductively coupled plasma-optical emission spectrometry

A new method using diluted reagents (nitric and hydrochloric acids and oxygen peroxide) and ultrasound energy to assist metals acid leaching with from edible seaweed was optimized. The method uses a first sonication at high temperature with hydrochloric acid as a previous stage to an ultrasound-assisted acid leaching with 7 ml of an acid solution containing nitric acid, hydrochloric acid and hydrogen peroxide at concentrations of 3.7, 3.0 and 3.0 M, respectively. Optimum conditions for the first sonication step were ultrasound energy at 17 kHz, sonication temperature at 65 °C, an acid volume of 2 ml, an hydrochloric acid concentration of 6.0 M and a sonication time of 10 min. It has been found that the first sonication stage at high temperature with hydrochloric acid is necessary to obtain quantitative recoveries for As, Ba, Fe and V. Otherwise quantitative recoveries were reached for the other elements investigated (Ca, K, Na, Mg, Cd, Cr, Cu, Mn, Ni, Pb and Zn). The repeatability of the ultrasound-assisted acid leaching method was around 10% for all elements. Adequate limit of detection and limit of quantification were reached by using inductively coupled plasma-optical emission spectrometry (ICP-OES) for measurements. The method resulted accurate after analysing several seaweed certified reference materials (IAEA-140/TM, NIES-03 and NIES-09). The method was finally applied to the multi-element determination in edible seaweed samples.     

Determination of trace elements in human serum by inductively coupled plasma atomic emission spectrometry with flow injection

An analytical method for the simultaneous determination of some trace elements (Au, Fe, Mg, Li, Sr, Zn) in human serum by inductively coupled plasma atomic emission spectrometry (ICP-AES) with flow injection is described. Physical interference caused by the change of sample viscosity is discussed. When 100 μl of serum was injected, the relevant recoveries of > 99% for Li, > 98% for Cu and Mg, > 95% for Fe were obtained for an NIST SRM with R.S.D. > 1.3% using optimized flow injection parameters. The prepared lyophilized control serum for routine analysis in clinical laboratories was analyzed and verified for the validity of the technique employed in this experiment using NIST SRM 909 as a primary reference material.     

The use of electrothermal vaporization ICP-OES for the determination of trace elements in human hair using slurry sampling and PTFE as modifier

A procedure for the determination of trace elements in human hair has been proposed by electrothermal vaporization inductively coupled plasma optical emission spectrometry (ETV-ICP-OES) with slurry sampling. Slurry was prepared by immersing human hair with conc. HNO₃ and then adding a polytetrafluoroethylene (PTFE) slurry, which was used as a chemical modifier for the improvement of vaporization characteristic of analyte. The slurry was homogenized with an ultrasonic vibrator before the measurement. The vaporization behaviour of the analytes in slurry and solution and the main influence factors for the determination were studied with the addition of PTFE systematically. Detection limits for this method varied from 0.033?µg?g^?1 (Cu) to 3.21?µg?g^?1 (Zn) with the relative standard deviations (RSDs) of 2.8–7.1%. The proposed method was successfully applied for the determination of trace elements (Cu, Mn, Cr, Fe, Zn, Cd and Pb) in human hair with minimum chemical pretreatment and aqueous calibration. The accuracy was checked by comparing the results of this method with those using pneumatic nebulization (PN) ICP-OES after a conventional acid decomposition of the same sample. In addition, the standard reference material of human hair (GBW 07601) was analysed with good agreement between the results from the proposed method and the certified values.     

电感耦合等离子体质谱法同时测定成品烟烟丝中7种微量元素

采用微波消解前处理样品,电感耦合等离子体质谱检测,同时测定了成品烟烟丝中Cr、Ni、Cu、As、Se、Cd、Pb等7种微量元素。方法的回收率92.8%~120%,检出限25.2~245 ng/L,相对标准偏差均小于10%。分析和比较了5种国外卷烟和10种国内卷烟烟丝中7种元素的含量。     

Levels of essential and potentially toxic trace metals in Antarctic macro algae

Eleven species of Antarctic algae were examined for their accumulation ability in the uptake of different metals and metalloids from the Antarctic aquatic environment. Macro algae were collected during the 2000 austral summer season at Jubany Station (Argentinean base) around Potter Cove, King George Island. The elements quantified were: As, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Se, Sr, V, and Zn. An optimized microwave-assisted digestion procedure was used to digest the samples and the elements were determined by inductively coupled plasma optical emission spectrometry. A wide range of metal retention capacity among the different species was observed. The highest levels of trace elements were found in Monostroma hariotii and Phaeurus antarcticus, with concentrations up to 3095 μg g⁻¹ for Fe. On the basis of the levels of trace elements observed in Monostroma hariotii and its wide distribution in the Antarctic Peninsula, this organism accomplishes a number of prerequisites to be considered as an adequate biomonitor for future studies.     

Determination of total mercury in coal fly ash by gold amalgamation cold vapour atomic absorption spectrometry

A method for the determination of total mercury in coal fly ash by gold amalgamation cold vapour atomic absorption spectrometry (CV-AAS) was optimized. Most of the experiments were performed on NBS SRM 1633a Coal Fly Ash with a certified value of 160 ± 10 ng Hg g^?1. The main attention was focused on the decomposition of the sample. The efficacy of pressure decompositions in closed silica and sealed Pyrex tubes using various combinations of acids (HNO₃, HCl, HClO₄) was compared with oxidative combustion of the coal fly ash. Notwithstanding the incomplete mineralization of the sample in sealed tubes, the results obtained showed good agreement with the certified value and results obtained by neutron activation analysis (NAA), which suggests that mercury is quantitatively released from the sample into solution. Lower results were obtained using decomposition in closed (but not hermetically sealed) silica tubes owing to losses of mercury by volatilization during decomposition. Interferences from some metal ions (nickel, lead, copper, silver, palladium, zinc and antimony) were also examined. The results showed a serious depression of the mercury signal only when gold, palladium and platinum were present at higher concentrations, which never or very seldom occur in fly ash matrices, and therefore do not represent a limitation of the method.     

Direct multielement trace analyses of silicon carbide powders by spark ablation simultaneous inductively coupled plasma optical emission spectrometry

A procedure for the direct analysis of silicon carbide powders (SiC) by simultaneous detection inductively coupled plasma optical emission spectrometry using a Spectro-CIROS™ spectrometer (CCD-ICP-OES) and a novel spark ablation system Spectro-SASSy (SA) as sample introduction technique is described. The sample preparation procedure for SA of non-conducting material is based on mixing the sample powders with a conducting matrix, in this case copper and briquetting pellets. Pressing time, pressure and mixing ratio are shown to be important parameters of the pelleting technique with respect to their mechanical stability for the reliability of the analysis results. A mixing ratio of 0.2 g +0.6 g for SiC and Cu, a pressure of 10 t cm^− 2 and a pressing time of 8 min have been found optimum. It has also been shown that the spark parameters selected are crucial for uniform volatilization. Electron probe micrographs of the burning spots and the analytical signal magnitude showed that a rather hard spark at 100 Hz was optimum. The determination of trace elements in silicon carbide powders is demonstrated using a calibration based on the addition of standard solutions. For Al, Ti, V, Mn and Fe detection limits in the lower µg g^− 1 range can be achieved. Internal standardization with Y in combination with the addition of standard solutions allows relative standard deviations in the range of 4 to 24% for concentration levels of the order of 3 to 350 µg g^− 1.     

催化褪色光度法测定粉煤灰中痕量钼

在pH11.0的Na2CO3 NaHCO3缓冲溶液中,痕量钼(Ⅵ)对H2O2氧化偶氮胭脂红B的褪色反应具有强烈的催化作用,据此建立了一种测定痕量钼(Ⅵ)的催化光度法的新方法。方法的检出限为2.04×10-2μg/L,线性范围为0～6.0μg/L,该法已应用于粉煤灰中痕量钼的测定。