Influence of MnO<Subscript>2</Subscript> on the photocatalytic activity of P-25 TiO<Subscript>2</Subscript> in the degradation of methyl orange

Influences of α-MnO₂, β-MnO₂, and δ-MnO₂ on the photocatalytic activity of Degussa P-25 TiO₂ have been investigated through the photocatalytic degradation of methyl orange. The TiO₂ photocatalyst, before and after being contaminated by MnO₂, was characterized by UV-visible diffuse reflectance spectroscopy (UV-vis DRS), photoluminescence (PL), and X-ray photoelectron spectroscopy (XPS). The results showed that photocatalytic activity of TiO₂ could be inhibited significantly or completely deactivated due to the presence of even a small amount of MnO₂ particles. It was found that the poisoning effect varied with the crystal phases of MnO₂ and the effect was in the order δ-MnO₂ >α-MnO₂ >β-MnO₂. The poisoning effect was attributed to the formation of heterojunctions between MnO₂ and TiO₂ particles. The heterojunctions changed the chemical state of Ti⁴⁺ and O²⁻ sites in the crystalline phase of TiO₂. MnO₂ in contact with TiO₂ particles also broadens the band-gap of TiO₂, which decreases UV absorption of TiO₂. It can also create some deep impurity energy levels serving as photoelectron-photohole recombination center, which accelerates the electron-hole recombination. Supported by the National Natural Science Foundation of China (Grant No. 20477009) and the Natural Science Foundation of Hebei Province (Grant No. E2005000183)     

Photocatalytic activity of polyaniline/Fe-doped TiO2 composites by in situ polymerization method

This study was focused on the photocatalytic activity of polyaniline (Pani)/iron doped titanium dioxide (Fe–TiO₂) composites for the degradation of methylene blue as a model dye. TiO₂ nanoparticles were doped with iron ions (Fe) using the wet impregnation method and the doped nanoparticles were further combined with Pani via an in situ polymerization method. For comparison purposes, Pani composites were also synthesized in the presence undoped TiO₂. The photocatalyst and the composites were characterized by standard analytical techniques such as FTIR, XRD, SEM, EDX and UV–Vis spectroscopies. Fe–TiO₂ and its composites exhibited enhanced photocatalytic activity under ultraviolet light irradiation. Improved photocatalytic activity of Fe–TiO₂ was attributed to the dopant Fe ions hindering the recombination of the photoinduced charge carriers. Pani/Fe–TiO₂ composite with 30?wt.% of TiO₂ nanoparticles achieved 28% dye removal and the discoloration rate of methylene blue for the sample was 0.0025?min^?1. FTIR, XRD, SEM, EDX and UV–Vis spectroscopies supported the idea that Fe ions integrated into TiO₂ crystal structure and Pani composites were successfully synthesized in the presence of the photocatalyst nanoparticles. The novelty of this study was to investigate the photocatalytic activity of Pani composites, containing iron doped TiO₂ and to compare their results with that of Pani/TiO₂.     

Preparation and photocatalytic activity of TiO2-coated granular activated carbon composites by a molecular adsorption-deposition method

TiO₂ nanoparticle-coated granular activated carbon (GAC) composite photocatalysts (CPs) were successfully prepared by a molecular adsorption-deposition (MAD) method. The CPs were detected by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), BET surface area and UV-Vis adsorption spectroscopy, and their photoactivity was evaluated by methyl orange (MO) photodegradation. The results show that small-sized TiO₂ nanoparticles were dispersed well, deposited on the surface of GAC, and showed slight blue shift in comparison with pure TiO₂. With the increase in TiO₂ content, the CPs showed band gaps in lower energy, smaller surface areas and the higher content of Ti³⁺ ions. Compared with pure TiO₂ and others CPs samples, CPs-382 sample showed the highest photoactivity due to the optimum TiO₂ content and surface area besides the synergic effect of photocatalytic degradation of TiO₂ and adsorptive property of GAC. In addition, the CPs could be very easily reclaimed, recycled and reused for methyl orange removal while high photoactivity is preserved. Supported by the Natural Science Foundation of Hunan Province (Grant No. 06JJ50150), the Scientific Research Fund of Science and Technology Department of Hunan Province (Grant No. 2007GK3060) and Jishou University (Grant No. JSDXKYZZ200648)     

Influence of ThO<Subscript>2</Subscript> on the photocatalytic activity of TiO<Subscript>2</Subscript>

Microcomposites consisting of TiO₂ (or Ce-doped TiO₂) and ThO₂ (0.5–2% of the TiO₂ mass) are produced by sol-gel synthesis of TiO₂ in presence of ThO₂. X-ray diffraction study reveals the effects of ThO₂ (compared to the ThO₂-free TiO₂, obtained by the same method) on the anatase interplanar distances, crystallites size and phase composition. The photocatalytic tests in presence of the composites under UV irradiation reveal an increase of the Malachite Green degradation rate constant. The effect depends on the Th relative content, temperature of annealing of the catalyst and addition of other doping agent. The highest photocatalytic activity is observed for TiO₂ obtained at 550°C and containing 1% ThO₂. The composite exhibits activity in dark, also. The presence of Ce⁴⁺ ions is not an obligatory requirement for the realization of the ThO₂ effect. The reported results suggest that the radioactivity of the Th and/or its decay products is one of the main factors responsible for the increased photocatalytic activity of TiO₂.      

Effect of PEG with different <Emphasis Type="Italic">M</Emphasis><Subscript>W</Subscript> as template direction reagent on preparation of porous TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> with assistance of supercritical CO<Subscript>2</Subscript>

Titania–silica composite have been prepared using polyethylene glycol (PEG) with different molecular weights (M _w), PEG20000, PEG10000, and PEG2000, as template in supercritical carbon dioxide (SC CO₂). The composite precursors were dissolved in SC CO₂ and impregnated into PEG templates using SC CO₂ as swelling agent and carrier. After removing the template by calcination at suitable temperature, the titania–silica composite were obtained. The composite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and nitrogen sorption–desorption experiment. Photocatalytic activity of the samples has been investigated by photodegradation of methyl orange. Results indicate that there are many Si–O–Ti linkages in the TiO₂/SiO₂ composite; the PEG template has a significant influence on the structure of TiO₂/SiO₂. In addition, the TiO₂/SiO₂ prepared with PEG10000 exhibited high photocatalytic efficiency. So this work supplies a clue to control and obtain the TiO₂/SiO₂ composite with different photocatalytic reactivity with the aid of suitable PEG template in supercritical CO₂.     

原位红外光谱法研究Gd3+掺杂TiO2光催化降解乙烯性能

随着环境污染的日益严重,寻求环境友好、节能、高效的污染治理技术已成为各国科学研究者致力的目标。以TiO2半导体为主的多相光催化氧化技术因与传统污染处理技术相比具有许多优点而倍受青睐,但是,目前以TiO2为基础的光催化技术还存在量子效率低、太阳能利用率低等技术难题[1,2     

Microstructure of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> hybrid electrospun nanofibers and their application in dye degradation

SiO₂/TiO₂ hybrid nanofibers were prepared by electrospinning and applied for photocatalytic degradation of methylene blue (MB). The phase structure, specific surface area, and surface morphologies of the SiO₂/TiO₂ hybrid nanofibers were characterized through thermogravimetry (TG), X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), etc. XRD measurements indicated that doping of silica into TiO₂ nanofibers can delay the phase transition from anatase to rutile and decrease the grain size. SEM and BET characterization proved that silica doping can remarkably enhance the porosity of the SiO₂/TiO₂ hybrid nanofibers. The MB adsorption capacity and photocatalytic activity of the SiO₂/TiO₂ hybrid nanofibers were distinguished experimentally. It was found that, although increased silica doping content could enhance the MB adsorption capacity, the intrinsic photocatalytic activity gradually dropped. The SiO₂ (10 %)/TiO₂ composite nanofibers exhibited the highest MB degradation rate, being superior to SiO₂ (20 %)/TiO₂ or pure TiO₂.     

Enhancement of visible-light photocatalytic activity of Cu-doped TiO<Subscript>2</Subscript> nanoparticles

Bare TiO₂ and Cu-doped TiO₂ nanoparticles with different nominal doping amounts of Cu ranging from of 0.5 to 5.0 mol% were synthesized using the modified sol–gel method. The samples were physically characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer–Emmett–Teller-specific surface area, UV–Vis diffuse reflectance spectroscopy, zeta potential, X-ray photoelectron spectroscopy, inductively coupled plasma, and photoluminescence techniques. The Cu-doped TiO₂ exhibited good photocatalytic activity in mineralization of oxalic acid and formic acid under visible light irradiation. Photomineralization of oxalic and formic acids under visible light irradiation revealed greatly enhanced photoactivity exhibited by the 2.0 mol% Cu-doped TiO₂ photocatalyst compared to bare TiO₂ . The enhanced photocatalytic performance arises from copper ion doping in the TiO₂ structure, leading to an extended photoresponsive range, enhanced photogenerated charge separation, and transportation efficiency.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Structural characterization and photocatalytic properties of novel Bi<Subscript>2</Subscript>FeVO<Subscript>7</Subscript>

Bi₂FeVO₇ was prepared by a solid-state reaction technique for the first time and the structural and photocatalytic properties of Bi₂FeVO₇ were studied. The results shows that this compound crystallized in the tetragonal crystal system with space group I4/mmm. Moreover, the band gap of Bi₂FeVO₇ was estimated to be about 2.22(6) eV. For the photocatalytic water splitting reaction, H₂ or O₂ evolution was observed from pure water with Bi₂FeVO₇ as the photocatalyst by ultraviolet light irradiation. Degradation of aqueous methylene blue (MB) dye by photocatalytic way over this compound was further studied under visible light irradiation. Bi₂FeVO₇ shows higher catalytic activity compared to TiO₂ (P-25) for MB photocatalytic degradation under visible light irradiation. Complete removal of aqueous MB was realized after visible light irradiation for 170 min with Bi₂FeVO₇ as the photocatalyst. The reduction of the total organic carbon (TOC) and the formation of inorganic products, SO ₄ ²⁻ and NO ₃ ⁻ revealed the continuous mineralization of aqueous MB during the photocatalytic course.     

Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.     

Photocatalytic degradation of methylene blue on Fe3+-doped TiO2 nanoparticles under visible light irradiation

Fe³⁺-doped TiO₂ composite nanoparticles with different doping amounts were successfully synthesized using sol-gel method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and ultravioletvisible spectroscopy (UV-Vis) diffuse reflectance spectra (DRS). The photocatalytic degradation of methylene blue was used as a model reaction to evaluate the photocatalytic activity of Fe³⁺/TiO₂ nanoparticles under visible light irradiation. The influence of doping amount of Fe³⁺ (ω: 0.00%–3.00%) on photocatalytic activities of TiO₂ was investigated. Results show that the size of Fe³⁺/TiO₂ particles decreases with the increase of the amount of Fe³⁺ and their absorption spectra are broaden and absorption intensities are also increased. Doping Fe³⁺ can control the conversion of TiO₂ from anatase to rutile. The doping amount of Fe³⁺ remarkably affects the activity of the catalyst, and the optimum efficiency occurs at about the doping amount of 0.3%. The appropriate doping of Fe³⁺ can markedly increase the catalytic activity of TiO₂ under visible light irradiation. __________ Translated from Journal of Northwest Normal University (Natural Science), 2006, 42(6): 55–56 [译自: 西北师范大学学报(自然科学版)]     

Photocatalytic degradation of organic compounds in aqueous systems by Fe and Ho codoped TiO<Subscript>2</Subscript>

Undoped, single-doped, and codoped TiO₂ nanoparticles were prepared by the sol-gel method and characterized with X-ray diffraction (XRD), the Brunauer-Emmett-Teller (BET)-specific surface area (S_BET), UV-Vis absorption spectra (UV-Vis), and X-ray photoelectron spectroscopy (XPS). Their photocatalytic activity was evaluated by methyl orange (MO) degradation in an aqueous suspension under UV or simulated solar light illumination. XRD showed that all samples calcined at 600°C preserved the anatase structure, and doping inhibited the increase of crystallite size. The BET result revealed that doping improved the surface area of TiO₂. UV-Vis indicated that Fe³⁺-doping broadened the absorption profile of TiO₂. XPS demonstrated that doping was advantageous to absorb more surface hydroxyl groups or chemisorbed water molecules. Photocatalytic degradation showed that the photocatalytic activity of TiO₂ codoped with Fe³⁺ and Ho³⁺ ions was markedly improved. This was ascribed to the fact that there was a cooperative action in the two doped elements. Fe³⁺-doping broadens the absorption profile, improves photo utilization of TiO₂, and then generates more electronhole pairs. Ho³⁺-doping restrains the increase in grain size and retards the recombination of photo-generated electrons and holes.     

Photocatalytic intercalated material based on HLaNb<Subscript>2</Subscript>O<Subscript>7</Subscript> as host and Cd<Subscript>0.8</Subscript>Zn<Subscript>0.2</Subscript>S as guest

A novel photocatalytic material (Pt,Cd0.8Zn0.2S)/HLaNb2O7 was fabricated by successive intercalation and exchange reactions. The (Pt,Cd0.8Zn0.2S)/HLaNb2O7 possessed a gallery height less than 0.5 nm and showed a broad absorption with wavelength over 370-500 nm. Using (Pt,Cd0.8Zn0.2S)/HLaNb2O7 as catalyst, the photocatalytic H2 evolution was more than 160 cm3·h-1·g-1 in the presence of Na2S as a sacrificial agent under irradiation with wavelength more than 290 nm from a 100-W mercury lamp. Furthermore, the catalyst showed photocatalytic activity even under visible light irradiation.     

Influence of NH<Subscript>3</Subscript>-treating temperature on visible light photocatalytic activity of N-doped P<Subscript>25</Subscript>-TiO<Subscript>2</Subscript>

The influence of NH₃-treating temperature on the visible light photocatalytic activity of N-doped P₂₅-TiO₂ as well as the relationship between the surface composition structure of TiO₂ and its visible light photocatalytic activity were investigated. The results showed that N-doped P₂₅-TiO₂ treated at 600°C had the highest activity. The structure of P₂₅-TiO₂ was converted from anatase to rutile at 700°C. Moreover, no N-doping was detected at the surface of P₂₅-TiO₂. There was no simply linear relationship between the visible light photocatalytic activity and the concentration of doped nitrogen, and visible light absorption. The visible light photocatalytic activity of N-doped P₂₅-TiO₂ was mainly influenced by the synergistic action of the following factors: (i) the formation of the single-electron-trapped oxygen vacancies (denoted as V_o^·); (ii) the doped nitrogen on the surface of TiO₂; (iii) the anatase TiO₂ structure.     

原位红外光谱法研究La/TiO2对有机污染物的光催化降解

本工作采用改进的溶胶-凝胶法和浸渍法制备了TiO₂掺杂稀土离子La³⁺的La/TiO₂光催化剂，运用XRD、N₂吸附脱附、紫外可见漫反射光谱(DRS)、表面光电压谱(SPS)等手段进行表征，同时利用原位红外技术考察了La/TiO₂样品光催化降解乙烯、丙酮、苯的气-固相光催化氧化反应，对其光催化降解有机污染物的过程进行了研究。结果表明，TiO₂经适量La³⁺掺杂后，锐钛矿晶型的含量增加，晶粒度减小，比表面积增大，禁带宽度增加，表面光电压信号增强，光生电子-空穴对有效分离；La/TiO₂样品对乙烯、丙酮、苯的光催化性能与纯TiO₂相比均有不同程度的改善，乙烯可以被光催化氧化完全矿化生成CO₂，而丙酮被光催化氧化可能生成中间产物丙酸，苯被光催化氧化可能生成中间产物苯酚和苯醌。     

Fabrication and photocatalytic property of TiO<Subscript>2</Subscript> nanofibers

TiO₂ nanofibers were prepared from tetrabutyl titanate sol precursors by using electrospun method. X-ray diffraction (XRD) and atomic force microscope (AFM) were used to characterize their crystal structure and morphology feature. The results demonstrated that TiO₂ nanofibers possessed anatase phase and the average diameter of TiO₂ nanofibers was about 150 nm. The photocatalytic property of TiO₂ nanofibers was evaluated for the photodecomposition of methyl orange solution. And TiO₂ nanofibers exhibited high photocatalytic activities with transfer efficiency about 100% after 20 min.     

Hydrothermal synthesis of (Fe,N) co-doped TiO<Subscript>2</Subscript> powders and their photocatalytic properties under visible light irradiation

(Fe, N) co-doped titanium dioxide powders have been prepared by a quick, low-temperature hydrothermal method using TiOSO₄, CO(NH₂)₂, Fe(NO₃)₃, and CN₃H₅ · HCl as starting materials. The synthesized powders were characterized by XRD, TEM, BET, XPS, and UV–Vis spectroscopy. Experimental results show that the as-synthesized TiO₂ powders are present as the anatase phase and that the N and Fe ions have been doped into the TiO₂ lattice. The specific surface area of the powders is 167.8 m²/g by the BET method and the mean grain size is about 11 nm, calculated by Scherrer’s formula. UV–Vis absorption spectra show that the edge of the photon absorption has been red-shifted up to 605 nm. The doped titanium dioxide powders had excellent photocatalytic activity during the process of photo-degradation of formaldehyde and some TVOC gases under visible light irradiation.     

Doped titanium dioxide nanocrystalline powders with high photocatalytic activity

Doped titanium dioxide nanopowders (M:TiO₂; M=Fe, Co, Nb, Sb) with anatase structure were successfully synthesized through an hydrothermal route preceded by a precipitation doping step. Structural and morphological characterizations were performed by powder XRD and TEM. Thermodynamic stability studies allowed to conclude that the anatase structure is highly stable for all doped TiO₂ prepared compounds. The photocatalytic efficiency of the synthesized nanopowders was tested and the results showed an appreciable enhancement in the photoactivity of the Sb:TiO₂ and Nb:TiO₂, whereas no photocatalytic activity was detected for the Fe:TiO₂ and Co:TiO₂ nanopowders. These results were correlated to the doping ions oxidation states, determined by Mössbauer spectroscopy and magnetization data.     

Temperatures and kinetics of anatase to rutile transformation in doped TiO<Subscript>2</Subscript> heated in microwave field

The influence of aliovalent ions such as Mn, Cr, Fe, Mo, and V on the temperature and kinetics of anatase to rutile phase transformation in TiO₂ heated in microwave field was studied in this work. The results indicated that heat treatment method and dopants considerably affected the anatase-to-rutile phase transition temperature and kinetics of transformation. The activation energy for anatase to rutile transformation of TiO₂ derived from the isothermal data was found to be 328.4 kJ mol^–1, which was considerably reduced by the addition of dopants in TiO₂ matrix. The activation energy for Mo, Mn and V doped samples was 252.0, 101.3 and 96.4 kJ mol^–1, respectively.